This document provides specifications for a low-voltage circuit breaker motor control center, including:
1) Project details such as location, codes, temperature ranges, and system voltage/frequency.
2) Options for the unit including NEMA ratings, control power transformers, overload relays, motor protection devices, and contactors.
3) Requirements for the enclosure, main power bus, grounding, and documentation including schematics, nameplates, and operating manuals.
This document provides specifications for a low-voltage circuit breaker motor control center, including:
1) Project details such as location, codes, temperature ranges, and system voltage/frequency.
2) Options for the unit including NEMA ratings, control power transformers, overload relays, motor protection devices, and contactors.
3) Requirements for the enclosure, main power bus, grounding, and documentation including schematics, nameplates, and operating manuals.
This document provides specifications for a low-voltage circuit breaker motor control center, including:
1) Project details such as location, codes, temperature ranges, and system voltage/frequency.
2) Options for the unit including NEMA ratings, control power transformers, overload relays, motor protection devices, and contactors.
3) Requirements for the enclosure, main power bus, grounding, and documentation including schematics, nameplates, and operating manuals.
Data Sheet for Low-Voltage Circuit Breaker Motor Control Centers
Client Engineering Org. Spec. No.
Project Title Location Date Project Location Contract No. Equip. No. Proj. No. Specifier Name Tele. No. P. O. No. Refer to PDVSA N-274 for General Requirements Applicable State and Local Codes: Data Provided by: Buyer Bidder with Proposal Seller after Order Site Conditions Unit Options Altitude Feet Seismic Zone NEMA Wiring Ambient Temp: Max C Min C Class I - Type B Other System Parameters Control Power Transformers V Phase Hertz Wire 480/120 VAC Other Available Fault Current Individual CPTs Other Incoming Line Power Extra VA Line Enters Overload Relays Top Bottom Electro-Mechanical Electronic (Solid State) Left Right Automatic Reset Ambient Compensated Top Hat 12" " Class 20 Class 10 Lugs Only Main Circuit Breaker A Heaters Sized per Buyer’s Attachments Lugs Without Heaters Lugs by Seller Copper Aluminum Motor Protection Devices Qty Wire(s) per Phase Wire Size AWG Thermal-Magnetic Magnetic Only MCC Enclosure Adjustment Range NEMA Per NEC Table Other Outdoor Enclosure (See PIP ELSSG12) Indoor Contactors – Size 4 & Above 1 (Standard) 3R Drip-Proof Magnetic Air Vacuum 1A Gasket 12 Dust-Tight Accessories Front Only Back-to-Back Automatic Shutters 15" Deep 20" Deep " Deep Provisions for Two-Hole Compression Lugs Units > 100 A Standard Finish Unit Load Cable Lugs by Seller Custom Finish Space for Future Unit Internal Devices Expansion Cover Plate(s) Required Left Right Surge Suppressors on Contactor Coils Horizontal Wireway Size 6" Min. Other Other Unit Devices Space Heater Required High-Temp Cutout Heater CB Door-Mounted Devices Thermostat Control Test PB and Ammeter Main Power Bus Nameplates Bus Duct A Close Coupled 1" x 2-1/2" (Std.) Other Bus Bracing White Tag/Black Letters Other 42,000 A 65,000 A 3/16" Letters Other 50,000 A 100,000 A Engraved Plastic Other Bus Material (Horizontal and Vertical) Door-Mounted Device Nameplate Located Inside Door Copper Aluminum Documentation Bus Joint Plating Schematic Diagrams Manufacturer Standard Manufacturer’s Standard Tin-Plated Silver-Plated Other By Buyer Horizontal Power Bus Electronic Document Format .DXF Other 600 A 800 A 1000 A Manufacturer to Provide: Reproducible Plus Number of Copies of All Documentation Plus 1 Copies of the Operating Manuals 2 Additional Documentation Requirements 0 0
A 1600 A 2000 A 2500 A Vertical Power Bus 300 A 600 A 450 A 800 A Ground Bus Size: Manufacturer Std. 1/4" X 1" Other Vertical Copper Ground Bus Other Horizontal Copper Ground Bus Top Bottom