Professional Documents
Culture Documents
Completion Equipment
1
Ver.0
Mostafa Ghifary August 2021
11. (L2) Which of the following are closing mechanisms used in Tubing
Retrievable Surface Controlled DHSV? (2 answers)
a. Poppet
b. Flapper
c. Plug
d. Ball
e. Sleeve
f. Gate.
12. When a Tubing retrievable DHSV is run into the well we need to lock it open
a.False
b. True.
2
Ver.0
Mostafa Ghifary August 2021
13. (L2) Which of the following DHSV‟s are sub-surface controlled? (2 answers)
How the subsurface DHSV operated? (2 answers)
a.Differential pressure (change in differential pressure at valve)
b. Ambient pressure (change in ambient pressure at valve)
c. Wireline retrievable
d. Tubing retrievable
e. Ball
f. Flapper.
g. Hydraulic pressure
h. Rise in temperature of wellbore fluid
i. Fall in temperature of wellbore fluid
15. Can a dummy SPM positively isolate the annulus from the tubing?
a.Yes
b. No
16. (L2) What is the primary reason that determines the setting depth of the
DHSV?
a. To prevent deliberate sabotage
b. Is set as high as possible to reduce the volume of well bore fluids that
might escape above the valve
c.Is set below the depth where it can be damaged by surface impact,
explosion, or cratering
d. Is set below the cratering depth from a blow out around the casing
e. Is set as close to the packer as possible to keep well pressure as deep as
possible
f. To prevent accidental penetration of drilling tools from an adjacent well.
3
Ver.0
Mostafa Ghifary August 2021
18. Would it be an acceptable practice to lock open and set an insert valve to
reinstate production in a well with a failed tubing retrievable DHSV?
a. No
b. Yes
23. (L2) How do lock mandrels (flow control devices) seal within the nipple
bore?
a. With slips
b. On No-Go shoulders
c. With mandrel locking dogs in matching profiles
d. With expanding rubber elements in the bore
e.With elastomeric packing in a polished nipple bore
f. By metal to metal seals.
4
Ver.0
Mostafa Ghifary August 2021
25. What are the main advantages of the production packer in well completion
(2 answers)
a.Isolate inner annulus from tubing string
b. Anchor tubing string
c. Suspend tubing string
d. Prevent well fluid and treatment fluids enter the outer annulus
27. Which of the following statements about the circulation devices used in a well
kill is true? (2 answers)
a. Check that the pressure rating is adequate for the work to be performed
b. Check the pressures are equalized at the device level before opening
c.Check that the device is fully open
d. Check that the tail pipe plug is in place before opening the sleeve
e. Check that the catcher is installed below the sliding sleeve
28. (L2) Name the two basic packer types used in completions. (2 answers)
a. Bridge plug
b. Permanent
c. Pump through
d. Retrievable
e. Check valve.
5
Ver.0
Mostafa Ghifary August 2021
29. (L2) How is a surface controlled wireline retrievable DHSV run in the open
position?
a. With locked in hydraulic pressure
b. With a lock open sleeve
c.With a prong on the wireline running tool
d. With an automatic ‘J’ device.
30. (L2) Which DHSV has the largest ID for the same tubing size?
a. Wireline retrievable
b. Tubing retrievable
c. Ambient pressure
d. Differential pressure.
31. (L2) What is the main reason for using tubing nipples?
a.To receive flow control devices
b. To reduce well flow
c. For wireline depth control.
33. (L2) Which of the following statements are true regarding side pocket
mandrels? (2 answers)
a. The SPM plugs the tubing
b. The SPM is the receptacle for the DHSV
c.The SPM is the receptacle for the gas lift valves
d. The SPM is the receptacle for the downhole plugs
e.The SPM can provide a means of communication between annulus and
tubing by itself or by valve set inside it.
34. (L2) Which of the following DHSVs are surface controlled? (2 answers)
a. Differential pressure
b. Ambient pressure
c. Wireline retrievable
d. Tubing retrievable.
6
Ver.0
Mostafa Ghifary August 2021
38. (L2) What is the main advantage of using wireline retrievable DHSVs?
a. Simple construction
b. Can be installed after running the completion
c. Can be removed to allow intervention work
d. Can be easily retrieved and replaced.
39. Does the check valve in a gas lift valve, fitted in an SPM, prevent well bore
fluids entering the annulus?
a. No
b. Yes.
40. (L2) What stops wellbore fluids entering the annulus through gas lift valve in
SPM
a. Differential pressure
b.Check valve in gas lift valve
c. The venturi effect across the port of the gas lift valve
7
Ver.0
Mostafa Ghifary August 2021
43. (L2) Which of the following statements about tubing hangers are true?
(3 answers)
a.A plug can usually be set inside the hanger body
b. It supports the weight of the bottom of the completion
c. It supports the weight of the top of the completion
d. It allows communication from inside the completion to the completion
annulus through the control line port(s)
e. It allows communication into the completion annulus through the control
line port(s)
f.It isolates the completion from the completion annulus
g. It can be closed by applying pressure to the control line.
44. (L2) Which of the following statements about Xmas tree valves is true?
a. All Swab valves can be used to cut Slickline
b.Some master valves can be used to cut Slickline
c. Any (all) flow wing valve can be used to cut Slickline
d. Any (all) kill wing valve can be used to cut Slickline.
46. (L2) Which of the following statements about Xmas tree valves are true?
(2 answers)
a.After closing, a manual valve handle should be backed out by part of a
turn
b. The valve must be closed as tightly as possible
c. All valves take 30 turns to open or close
d. The indicator shows how many turns have to be made
e.Counting the turns as the valve is opened or closed can show any
obstructions in front of the valve.
8
Ver.0
Mostafa Ghifary August 2021
47. (L2) When being used as a communication device, what could be installed in
the SPM to isolate (positive closure) the annulus from the tubing (block flow
in both directions)?
a. A gas lift valve
b. A gate valve
c.A dummy valve
d. A chemical injection valve
e. A circulation valve
50. (L2) What is the primary purpose (function) of No-Go shoulders in nipples?
a.To locate the correct lock mandrel to their particular matching nipple
b. In the bottom nipple to prevent the tools falling out of the bottom of the
tubing
c. To bear the load from the differential pressure across the plug
d. To lock the mandrel into the nipple.
51. What is the primary function of the No-Go shoulder on the equipment
stopper?
a.To guide the locking dogs on a wireline tools to a suitable nipple profile
b. To prevent equipment falling out of the production string when the
shoulder is installed on the bottom nipple profile
c. To relieve forces when there is a pressure differential across the
equipment
d. To lock a wireline tool into nipple profile
9
Ver.0
Mostafa Ghifary August 2021
52. (L2) What is the correct action to take to temporarily re-instate production
in a well with a failed tubing retrievable DHSV?
a. Workover the well
b. Lock open DHSV
c.Lock open DHSV (lock the valve mechanism open) and install an insert
valve
d. Rig up wireline and replace the valve
53. (L2) How is tubing retrievable DHSV run in the open position? (2 answers)
a.With pressure on control line
b. By using the lock open mechanism
c. With straddle set across the valve
d. By keeping the tubing pressurized
e. By pumping above the valve to equalize the pressure differential
54. No-Go shoulders in landing nipples enable the correct lock mandrel to be
located in it?
a.True
b. False
55. (L2) Given the drawing below, match the correct numbers to their
description
10
Ver.0
Mostafa Ghifary August 2021
56. Figure below illustrates the profile of an API 6BX type flange. Which
number indicates the Nominal flange dimension?
a.Dimension No. 1.
b. Dimension No. 2.
c. Dimension No. 3.
d. Dimension No. 4.
57. Which one of API flanges has a specified distance between “made-up
flanges” that require occasional re-tightening of bolts/studs and nuts?
a.API type 6B.
b. API type 6BX.
58. Which of the following statements about ring gaskets are correct?
(2 answers)
a. Ring gaskets may be used several times
b. The same material specifications apply to ring gaskets as to ring grooves.
c. Type RX and BX ring gaskets provide a pressure-energized seal.
d. Only BX ring gaskets can be used with 6BX type flanges.
59. Which one of these gaskets matches the 6BX type flange?
a. Type R Octagonal.
b. Type BX.
c. Type RX.
60. Select the correct types that illustrate pressure energized ring gaskets
(2 answers).
a. Type R Octagonal.
b. Type R Oval.
c. Type RX.
d. Type BX.
61. Select the pressure-energized type of ring gasket that should be used for
flanged BOP connection type 6B.
a. Type R Octagonal.
b. Type R Oval.
c. Type RX.
d. Type BX.
11
Ver.0
Mostafa Ghifary August 2021
63. 6BX flanges with BX gaskets require more checking than 6B with RX
gaskets.
a. True
b. False
64. The nominal size of a flange is the diameter of the required gasket.
a. True
b. False
65. Which one of the following rated working pressure does not match an API
type 6B flange?
a. 10000 psi.
b. 2000psi.
c. 3000psi.
d. 5000psi.
66. (L2) Which of the following best describes a 7 1/16” 10,000 psi flange?
a. It is designed to have an ‘RX’ gasket
b. It has a 10,000 psi test pressure and 5,000 psi working pressure
c. It has a 7 1/16” OD and 10,000 psi working pressure
d.It has a 7 1/16” ID and 10,000 psi working pressure.
67. The term „6BX‟ when used to describe a flange refers to its size and rating?
a.False
b. True
68. (L2) What would be the effect of fitting a 71/16“ X 5,000 psi flange to a
10,000 psi rated BOP stack?
a. The rating would remain at 10,000 psi
b. The rating would become 5,000 psi
c. The rating would become 7,500 psi.
69. (L2) What is the meaning of the expression „6BX‟ for a flange?
a.Type
b. Dimension
c. Trademark
d. Serial number.
12
Ver.0