Professional Documents
Culture Documents
LOW-LEAKAGE, SINGLE-BLADE
PRODUCT DATA
Construction:
Frame: Sleeve-type, spiral duct, crimped on downstream side.
6 to 10 in. (152 to 254 mm) diameter: 24 gage galvanized
steel.
12 to 16 in. (305 to 406 mm) diameter: 22 gage galvanized
steel.
Sleeve length: Diameter plus 1 in. (25 mm), minimum length
12 in. (305 mm).
Blade: 16 gage galvanized steel.
Shaft: 1/2 in. (13 mm) diameter, zinc-coated steel.
Extends 3.875 in. (153mm) beyond actuator mounting
plate.
Bearings: Flanged bronze oilite, pressed into frame.
Seals: Closed-cell neoprene on frame with silicone rubber
bead.
Pressure Drop:
The D690 Round Damper is used in conventional air handling Max. at full open: 0.035 in. wc at 1000 ft/min (5 m/s).
systems to control airflow in a round duct. The damper is
specifically designed to mount to the Honeywell actuators. Leakage: 12.5 cfm per sq ft of Damper face at 1 in. wc.
Refer to Table 2 for leakage at pressures other than 1 in. wc.
FEATURES Torque:
Accommodates actuators of up to 44 lb-in. (5 Nm) of torque.
• Neoprene and silicone seal for tight closing and low
Mounting Plate:
leakage.
8.5 in. x 9 in. (width x length).
• Oilite bearings for long life.
Damper Opening:
• 90-degree damper travel for a variety of applications. Rotate clockwise (cw) to open.
• Designed to mount to a variety of Honeywell actuators
for an economical package. Actuator Mounting:
Attached plate for mounting Honeywell ML6161, ML6171,
MN6105, MN7505, Zelix model series, Spyder MicroVAV
SPECIFICATIONS Actuator.
1.0"
400
FRAME SEALS
CFM
0.5"
BLADE 300
BEARINGS
200
SHAFT CONTROL
ROD
100
0
0 10 20 30 40 50 60 70 80 90
1/2 IN.
DAMPER POSITION IN DEGREES M974
(12 MM)
6 TO 16 IN.
(152 TO 406 MM)
IN 2-IN. (51 MM)
Fig. 3. 6-inch D690 flowrate vs. damper position.
INCREMENTS 3-7/8 in.
(153 mm)
M33002
900
600
500
0.5"
CFM
400
300
200
100
0
0 10 20 30 40 50 60 70 80 90
DAMPER POSITION IN DEGREES M975
63-2577—01 2
D690 ROUND DAMPER
1400 3000
1.0"
1200 1.0"
2500
1000
0.5" 2000
800 CFM
0.5"
CFM 1500
600
1000
400
500
200
0 0
0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90
DAMPER POSITION IN DEGREES M976 DAMPER POSITION IN DEGREES M979
Fig. 5. 10-inch D690 flowrate vs. damper position, in Fig. 8. 16-inch D690 flowrate vs. damper position.
inches (mm).
1800
1.0"
1600
1400
1200
0.5"
1000
CFM
800
600
400
200
0
0 10 20 30 40 50 60 70 80 90
DAMPER POSITION IN DEGREES M977
1.0"
2000
1500
CFM 0.5"
1000
500
0
0 10 20 30 40 50 60 70 80 90
DAMPER POSITION IN DEGREES M978
3 63-2577—01
D690 ROUND DAMPER
M33005 M33063
M33006