You are on page 1of 240

A318/A319/A320/A321

SERVICE BULLETIN

CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.

ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - UP AND DOWN DATA LOADING


SYSTEM - INSTALL ARINC 615A PDL CONNECTOR FOR ATSU
MODIFICATION No.:
CONF 001 002 005-009
33443P8153
CONF 002-004 006-009
163660P18410
CONF 003
38958P11023
CONF 003 004
36208P8990

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 1
A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - UP AND DOWN DATA LOADING


SYSTEM - INSTALL ARINC 615A PDL CONNECTOR FOR ATSU
CONF ALL
REVISION TRANSMITTAL SHEET
This page transmits Revision No. 05 of Service Bulletin No. A320-31-1583.
A. ADDITIONAL WORK
No additional work is required by this revision.
B. REASON
Revision No. 05 issued to add aircraft MSN 03374 for operator AIJ.
C. CHANGES
CONF 001

SUMMARY
APPLICABILITY Operator added
CONCURRENT REQUIREMENTS Applicability updated
PLANNING INFORMATION
APPLICABILITY
Configuration definition Aircraft added
CONCURRENT REQUIREMENTS Applicability updated
CONF 002

SUMMARY
APPLICABILITY Operators updated
CONF 003
None
CONF 004
None
CONF 005
None
CONF 006
None
CONF 007

SUMMARY
APPLICABILITY Operator updated
CONF 008

SUMMARY
APPLICABILITY Operator updated
CONF 009

SUMMARY
APPLICABILITY Operator updated

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 2
A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
CONF ALL
D. FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete
document. Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
E. HISTORY OF PREVIOUS REVISIONS
Revision No. 01 issued to add aircraft and change the gauge of the wires 3138-0293 and
3138-0294 from CF24 to CF22 for CONF 002 and CONF 003.
Revision No. 02 issued to add aircraft for operators BAV, BKP, EZY, RZO, SHU and UAL.
Revision No. 03 issued to add aircraft MSN 02108 for operator IGO and add missing SBs in
Concurrent Requirements paragraph.
Revision No. 04 issued to add aircraft MSN 03069 for operator VOI.
F. REVISION SEQUENCE
ORIGINAL: Dec 12/19
REVISION No. : 01 - Mar 11/20
REVISION No. : 02 - Jun 03/20
REVISION No. : 03 - Sep 23/20
REVISION No. : 04 - Nov 30/20
REVISION No. : 05 - Apr 09/21

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 3
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - UP AND DOWN DATA LOADING


SYSTEM - INSTALL ARINC 615A PDL CONNECTOR FOR ATSU
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 002

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 003

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 36208P8990 38958P11023

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 004

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 36208P8990

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 005

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 33443P8153

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 4
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 006

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 007

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 008

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 009

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 163660P18410 33443P8153

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF ALL
B. REASON

(1) History
This Service Bulletin is issued further to an operator’s request.
(2) Objective/Action
For the aircraft already equipped with the Data Loading Routing Box (DLRB), this
Service Bulletin consists in the installation of:

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 5
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
- A connector to enable ARINC 615A data loading of the ATSU, within the
framework of ARINC 615A data loading with the PDL.
For the aircraft not equipped with the DLRB, this Service Bulletin consists in the
installation of:

- The wiring on the connector, to allow ARINC 615A data loading of the ATSU
(Ethernet high speed). This will allow the operator to use the PDL with ARINC
615A or ARINC 615-3 (low speed) protocols.
(3) Advantages
Accomplishment of this Service Bulletin fulfills the operator’s request.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION

EVALUATION TABLE
COMPLIANCE OPTIONAL COST SAVING NO
A/C OPERATION NO VENDOR SB NO
AFFECTED
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD NO
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

NOTE: Service Bulletin for convenience or option.

D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
CONF 002
No specific aircraft maintenance configuration required.
CONF 003
No specific aircraft maintenance configuration required.
CONF 004
No specific aircraft maintenance configuration required.
CONF 005
No specific aircraft maintenance configuration required.
CONF 006
No specific aircraft maintenance configuration required.
CONF 007
No specific aircraft maintenance configuration required.
CONF 008
No specific aircraft maintenance configuration required.
CONF 009
No specific aircraft maintenance configuration required.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 6
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A03R03 1 See SB Bundle, connector, label,
module, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 002
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A01R00 1 See SB Buttons, placard
Part kit 311583A04R02 1 See SB Bundle, C/B, connector, label,
modules, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A10R00 1 See SB Bundle
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 003
(1) Modification

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 7
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A02R00 1 See SB Buttons, placard
Part kit 311583A05R01 1 See SB Bundle, C/B, placard set
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A10R00 1 See SB Bundle
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 004
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A05R01 1 See SB Bundle, C/B, placard set
Part kit 311583A07R00 1 See SB Buttons, placard
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 005
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A03R03 1 See SB Bundle, connector, label,
module, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Components See SB See Note Cable ties

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 8
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
NOTE: Price information to be obtained from the given supplier.

CONF 006
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A04R02 1 See SB Bundle, C/B, connector, label,
modules, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Part kit 311583A07R00 1 See SB Buttons, placard
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 007
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A04R02 1 See SB Bundle, C/B, connector, label,
modules, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Part kit 311583A08R00 1 See SB Buttons, placard
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 008
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A04R02 1 See SB Bundle, C/B, connector, label,
modules, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Part kit 311583A09R00 1 See SB Buttons, placard
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF 009

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 9
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Part kit 311583A04R02 1 See SB Bundle, C/B, connector, label,
modules, placard set
Part kit 311583A06R00 1 See SB Cap, fasteners
Part kit 311583A09R00 1 See SB Buttons, placard
Components See SB See Note Cable ties

NOTE: Price information to be obtained from the given supplier.

CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
39K 39V 41N 82W 90Q ABY AIJ ART AUA BAV EOK ETD EZY GSW IGO RBG RWZ RZO SEK SHU
UAL VOI WRC

NOTE: This Service Bulletin is written for the operators listed above. The modification in
this Service Bulletin can be done by other operators. If other operators want to do
this modification, use the RFC/RMO procedure and write to:
AIRBUS
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE

G. CONCURRENT REQUIREMENTS

ON A/C 00357
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-34-1560  
Ref. SB A320-46-1043  
Ref. SB A320-46-1125  

NOTE: Service Bulletin No. Ref. SB A320-34-1560 (NAVIGATION - ILS - REMOVE


ILS COMPUTER AND INSTALL ADDITIONAL WIRING PROVISIONS FOR MMR
INSTALLATION).

NOTE: Service Bulletin No. Ref. SB A320-46-1043 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU SYSTEM ADVANCED PROVISIONS).

NOTE: Service Bulletin No. Ref. SB A320-46-1125 (INFORMATION SYSTEMS - ATIMS -


INSTALL FANS SYSTEM PROVISIONS).

ON A/C 01554, 01670, 01707, 01763, 01944, 02011, 02084, 02108, 02193, 02216, 02273,
02372, 02390, 02393, 02404, 02405, 02460, 02482, 02548, 02677, 02712, 02738, 02739,
02914, 03024, 03069

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 10
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 03246, 03356, 03361, 03374


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

ON A/C 02742, 02744, 02754, 02765, 02769, 02779, 02803, 02818


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  
Ref. SB A320-46-1126  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

NOTE: Service Bulletin No. Ref. SB A320-46-1126 (INFORMATION SYSTEMS — FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 11
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
ON A/C 03004, 03050
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  
Ref. SB A320-46-1134  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

NOTE: Service Bulletin No. Ref. SB A320-46-1134 (INFORMATION SYSTEMS — FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

ON A/C 03108, 03135


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


None  
And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 03234, 03268


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1121  

NOTE: Service Bulletin No. Ref. SB A320-46-1121 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE
2 ACTIVATED).

ON A/C 02325

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 12
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1121  

NOTE: Service Bulletin No. Ref. SB A320-46-1121 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE
2 ACTIVATED).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 01207
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1044  
Ref. SB A320-46-1125  

NOTE: Service Bulletin No. A320-46–1044 (INFORMATION SYSTEMS - ATSU - INSTALL ATSU
CSB4 WITH HARDWARE - 070 IN PREFANS CONFIGURATION).

NOTE: Service Bulletin No. A320-46–1125 (INFORMATION SYSTEMS - ATIMS - INSTALL FANS
SYSTEM PROVISIONS).

ON A/C 03152
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  
Ref. SB A320-46-1134  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

NOTE: Service Bulletin No. Ref. SB A320-46-1134 (INFORMATION SYSTEMS - FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 13
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS
— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 02495, 02565, 02578, 02605, 02636, 02646, 02691, 02715, 02777, 02782, 02795
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  
Ref. SB A320-46-1126  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

NOTE: Service Bulletin No. Ref. SB A320-46-1126 (INFORMATION SYSTEMS - FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

CONF ALL
H. NATURE OF THE WORK
CONF 001
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 002
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

AIRCRAFT YES
EQUIPMENT NO

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 14
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 003
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

AIRCRAFT YES
EQUIPMENT NO
CONF 004
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 005
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 006
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 007
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 008
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF 009

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 15
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT YES
EQUIPMENT NO
CONF ALL
I. MANPOWER
CONF 001
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 13.00 h
ELAPSED TIME (HOURS) 13.00 h
CONF 002
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

MANPOWER
TOTAL MAN-HOURS 7.50 h
ELAPSED TIME (HOURS) 7.50 h
CONF 003
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 14.50 h
ELAPSED TIME (HOURS) 14.00 h
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

MANPOWER
TOTAL MAN-HOURS 7.50 h
ELAPSED TIME (HOURS) 7.50 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 16
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 004
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 14.50 h
ELAPSED TIME (HOURS) 14.00 h
CONF 005
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 13.00 h
ELAPSED TIME (HOURS) 13.00 h
CONF 006
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h
CONF 007
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h
CONF 008
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h
CONF 009
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

MANPOWER
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 17
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF ALL
J. GENERAL OVERVIEW
CONF 001 005

INSTALLATION OF THE EQUIPMENT AND THE


WIRING IN AFT ELECTRONICS RACK 80VU

Z120

FR24

1M

INSTALLATION OF THE WIRING


BETWEEN AFT ELECTRONICS RACK
80VU AND FWD ELECTRONICS RACK 90VU

FR1

MODIFICATION OF THE EQUIPMENT


AND THE WIRING IN SHELF 93VU

ICN-A320-A-31XX1583-A-FAPE3-01RNC-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RNC-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
General Overview
REV 05 Apr 09/21 Page 18
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 002 006-009

INSTALLATION OF THE EQUIPMENT AND THE


WIRING IN AFT ELECTRONICS RACK 80VU

MODIFICATION OF THE
EQUIPMENT AND THE WIRING
IN REAR C/B PANEL 121VU

INSTALLATION OF THE WIRING


BETWEEN REAR C/B
PANEL 121VU AND AFT
ELECTRONICS RACK 80VU

Z210

FR24

1M

FR12
Z120
INSTALLATION OF THE WIRING
BETWEEN AFT ELECTRONICS RACK
FR1 80VU AND FWD ELECTRONICS RACK 90VU

MODIFICATION OF THE EQUIPMENT


AND THE WIRING IN SHELF 93VU

ICN-A320-A-31XX1583-A-FAPE3-01RN5-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RN5-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
General Overview
REV 05 Apr 09/21 Page 19
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 003 004

MODIFICATION OF THE WIRING


IN AFT ELECTRONICS RACK 80VU

MODIFICATION OF THE
EQUIPMENT AND THE WIRING
IN REAR C/B PANEL 121VU

INSTALLATION OF THE WIRING


BETWEEN REAR C/B
PANEL 121VU AND AFT
ELECTRONICS RACK 80VU

Z210

FR24

1M

FR12
Z120

FR1

ICN-A320-A-31XX1583-A-FAPE3-01RN4-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RN4-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
General Overview
REV 05 Apr 09/21 Page 20
A318/A319/A320/A321
SERVICE BULLETIN

ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - UP AND DOWN DATA LOADING


SYSTEM - INSTALL ARINC 615A PDL CONNECTOR FOR ATSU
CONF ALL
1. PLANNING INFORMATION
A. APPLICABILITY
(1) Models
ON A/C 02460, 02495, 02548, 02565, 02578, 02605, 02636, 02646, 02677, 02691, 02715,
02742, 02744, 02754, 02765, 02769, 02777, 02779, 02782, 02795, 02803, 02818
319-111
ON A/C 03024, 03108
319-112
ON A/C 03356
319-115
ON A/C 02273, 02404, 02738, 02739
319-132
ON A/C 03069
319-133
ON A/C 02011, 02325, 02390, 02712, 03135, 03152, 03234, 03246, 03268, 03361, 03374
320-214
ON A/C 00357
320-231
ON A/C 01944, 02084, 02108, 02193, 02372, 02393, 02405, 02482, 02914, 03004, 03050
320-232
ON A/C 01554
321-211
ON A/C 01207, 01670, 01707, 01763, 02216
321-231
CONF ALL
(2) Applicability by MSN
00357 01207 01554 01670 01707 01763 01944 02011 02084 02108 02193 02216
02273 02325 02372 02390 02393 02404 02405 02460 02482 02495 02548 02565
02578 02605 02636 02646 02677 02691 02712 02715 02738 02739 02742 02744
02754 02765 02769 02777 02779 02782 02795 02803 02818 02914 03004 03024
03050 03069 03108 03135 03152 03234 03246 03268 03356 03361 03374
(3) MSN by configuration
CONF 001

MSN CONFIGURATION
03234 03246 03268 03356 03361 03374 001
CONF 002

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 21
A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
02011 02084 02108 02216 02273 02325 02390 02404 02712 002
02738 02739 02914 03024 03069 03135
CONF 003

MSN CONFIGURATION
00357 003
CONF 004

MSN CONFIGURATION
01207 004
CONF 005

MSN CONFIGURATION
02495 02565 02578 02605 02636 02646 02691 02715 02777 005
02782 02795 03152
CONF 006

MSN CONFIGURATION
01554 006
CONF 007

MSN CONFIGURATION
01670 007
CONF 008

MSN CONFIGURATION
01707 01763 01944 02372 02393 02460 02548 02677 02742 008
02744 02754 02765 02769 02779 02803 02818 03004 03050
03108
CONF 009

MSN CONFIGURATION
02193 02405 02482 009
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 regards the specific PRE-SB status of the related aircraft.
CONF 001 retrofits following modifications: 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 22
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
Configuration 002
CONF 002 regards the specific PRE-SB status of the related aircraft.
CONF 002 retrofits following modifications: 163660P18410, 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 003
Configuration 003
CONF 003 regards the specific PRE-SB status of the related aircraft.
CONF 003 retrofits following modifications: 163660P18410, 36208P8990,
38958P11023.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 004
Configuration 004
CONF 004 regards the specific PRE-SB status of the related aircraft.
CONF 004 retrofits following modifications: 163660P18410, 36208P8990.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 005
Configuration 005
CONF 005 regards the specific PRE-SB status of the related aircraft.
CONF 005 retrofits following modifications: 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 006
Configuration 006
CONF 006 regards the specific PRE-SB status of the related aircraft.
CONF 006 retrofits following modifications: 163660P18410, 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 23
A318/A319/A320/A321
SERVICE BULLETIN

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 007
Configuration 007
CONF 007 regards the specific PRE-SB status of the related aircraft.
CONF 007 retrofits following modifications: 163660P18410, 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 008
Configuration 008
CONF 008 regards the specific PRE-SB status of the related aircraft.
CONF 008 retrofits following modifications: 163660P18410, 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF 009
Configuration 009
CONF 009 regards the specific PRE-SB status of the related aircraft.
CONF 009 retrofits following modifications: 163660P18410, 33443P8153.

NOTE: For further information concerning the Configuration Definition, refer to


Appendix CONFIGURATION DEFINITION TABLE.

NOTE: For the retrofitted modifications after accomplishment of this Service


Bulletin, refer to Appendix RETROFITTED MODIFICATION.

CONF ALL
B. CONCURRENT REQUIREMENTS

ON A/C 00357
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-34-1560  
Ref. SB A320-46-1043  
Ref. SB A320-46-1125  

NOTE: Service Bulletin No. Ref. SB A320-34-1560 (NAVIGATION - ILS - REMOVE


ILS COMPUTER AND INSTALL ADDITIONAL WIRING PROVISIONS FOR MMR
INSTALLATION).

NOTE: Service Bulletin No. Ref. SB A320-46-1043 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU SYSTEM ADVANCED PROVISIONS).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 24
A318/A319/A320/A321
SERVICE BULLETIN

NOTE: Service Bulletin No. Ref. SB A320-46-1125 (INFORMATION SYSTEMS - ATIMS -


INSTALL FANS SYSTEM PROVISIONS).

ON A/C 01554, 01670, 01707, 01763, 01944, 02011, 02084, 02108, 02193, 02216, 02273,
02372, 02390, 02393, 02404, 02405, 02460, 02482, 02548, 02677, 02712, 02738, 02739,
02914, 03024, 03069
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 03246, 03356, 03361, 03374


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

ON A/C 02742, 02744, 02754, 02765, 02769, 02779, 02803, 02818


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  
Ref. SB A320-46-1126  

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 25
A318/A319/A320/A321
SERVICE BULLETIN

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

NOTE: Service Bulletin No. Ref. SB A320-46-1126 (INFORMATION SYSTEMS — FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

ON A/C 03004, 03050


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  
Ref. SB A320-46-1134  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

NOTE: Service Bulletin No. Ref. SB A320-46-1134 (INFORMATION SYSTEMS — FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

ON A/C 03108, 03135


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


None  
And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 03234, 03268


Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 26
A318/A319/A320/A321
SERVICE BULLETIN

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1121  

NOTE: Service Bulletin No. Ref. SB A320-46-1121 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE
2 ACTIVATED).

ON A/C 02325
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1121  

NOTE: Service Bulletin No. Ref. SB A320-46-1121 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE
2 ACTIVATED).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 01207
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1044  
Ref. SB A320-46-1125  

NOTE: Service Bulletin No. A320-46–1044 (INFORMATION SYSTEMS - ATSU - INSTALL ATSU
CSB4 WITH HARDWARE - 070 IN PREFANS CONFIGURATION).

NOTE: Service Bulletin No. A320-46–1125 (INFORMATION SYSTEMS - ATIMS - INSTALL FANS
SYSTEM PROVISIONS).

ON A/C 03152
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  
Ref. SB A320-46-1134  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 27
A318/A319/A320/A321
SERVICE BULLETIN

NOTE: Service Bulletin No. Ref. SB A320-46-1134 (INFORMATION SYSTEMS - FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

ON A/C 02495, 02565, 02578, 02605, 02636, 02646, 02691, 02715, 02777, 02782, 02795
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-46-1030  
Ref. SB A320-46-1126  

NOTE: Service Bulletin No. Ref. SB A320-46-1030 (INFORMATION SYSTEMS - ATIMS -


INSTALL ATSU HARDWARE -070).

NOTE: Service Bulletin No. Ref. SB A320-46-1126 (INFORMATION SYSTEMS - FLIGHT


OPERATION PERIPHERALS - INSTALL FOMAX SYSTEM PROVISIONS).

And
This Service Bulletin cannot be accomplished if this/these Service Bulletin(s) has (have)
been accomplished:

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1411  

NOTE: Service Bulletin No. Ref. SB A320-31-1411 (INDICATING/RECORDING SYSTEMS


— UP AND DOWN DATA LOADING SYSTEM - REMOVE MDDU AND INSTALL PDL
CONNECTOR ON CENTER PEDESTAL).

CONF ALL
C. REASON

(1) History
This Service Bulletin is issued further to an operator’s request.
(2) Objective/Action
For the aircraft already equipped with the Data Loading Routing Box (DLRB), this
Service Bulletin consists in the installation of:

- A connector to enable ARINC 615A data loading of the ATSU, within the
framework of ARINC 615A data loading with the PDL.
For the aircraft not equipped with the DLRB, this Service Bulletin consists in the
installation of:

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 28
A318/A319/A320/A321
SERVICE BULLETIN

- The wiring on the connector, to allow ARINC 615A data loading of the ATSU
(Ethernet high speed). This will allow the operator to use the PDL with ARINC
615A or ARINC 615-3 (low speed) protocols.
(3) Advantages
Accomplishment of this Service Bulletin fulfills the operator’s request.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification
CONF 001 005
1 Modify the Equipment and the Wiring in Shelf 93VU
CONF 002 006-009
1 Modify the Equipment and the Wiring in Shelf 93VU
CONF 001
2 Install the Equipment and the Wiring in Aft Electronics Rack 80VU
CONF 002 006-009
2 Install the Equipment and the Wiring in Aft Electronics Rack 80VU
CONF 005
2 Install the Equipment and the Wiring in Aft Electronics Rack 80VU
CONF 003 004
3 Modify the Wiring in Aft Electronics Rack 80VU
CONF 001 005
4 Install the Wiring between Aft Electronics Rack 80VU and FWD Electronics
Rack 90VU
CONF 002 006-009
4 Install the Wiring between Aft Electronics Rack 80VU and FWD Electronics
Rack 90VU
CONF 002
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 003
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 004
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 006
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 007
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 008
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 009
5 Modify the Equipment and the Wiring in Rear C/B Panel 121VU
CONF 002 006-009

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 29
A318/A319/A320/A321
SERVICE BULLETIN

6 Install the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
CONF 003 004
6 Install the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
CONF 002 003
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin
1 Modify the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
CONF ALL
E. COMPLIANCE

(1) Classification
OPTIONAL: Service Bulletin for convenience or option.
(2) Accomplishment Timescale
In accordance with operators' maintenance schedule.
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 3.50 h
80VU

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 30
A318/A319/A320/A321
SERVICE BULLETIN

Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h
TOTAL MAN-HOURS 13.00 h
ELAPSED TIME (HOURS) 13.00 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 4.00 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 31
A318/A319/A320/A321
SERVICE BULLETIN

Install/Close for Access to FWD Electronics Rack 90VU 1.50 h


Close-up 1.00 h
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h

NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.

(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Close-up 0.50 h
TOTAL MAN-HOURS 7.50 h
ELAPSED TIME (HOURS) 7.50 h
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Wiring in Aft Electronics Rack 80VU 4.00 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 32
A318/A319/A320/A321
SERVICE BULLETIN

Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Close-up 1.00 h
TOTAL MAN-HOURS 14.50 h
ELAPSED TIME (HOURS) 14.00 h
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Close-up 0.50 h
TOTAL MAN-HOURS 7.50 h
ELAPSED TIME (HOURS) 7.50 h
CONF 004
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 33
A318/A319/A320/A321
SERVICE BULLETIN

(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Wiring in Aft Electronics Rack 80VU 4.00 h
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Close-up 1.00 h
TOTAL MAN-HOURS 14.50 h
ELAPSED TIME (HOURS) 14.00 h
CONF 005
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 3.50 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
PREPARATION FOR TEST

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 34
A318/A319/A320/A321
SERVICE BULLETIN

Job Set-up 0.50 h


TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h
TOTAL MAN-HOURS 13.00 h
ELAPSED TIME (HOURS) 13.00 h
CONF 006
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 4.00 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 35
A318/A319/A320/A321
SERVICE BULLETIN

TOTAL MAN-HOURS 20.00 h


ELAPSED TIME (HOURS) 11.00 h

NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.

CONF 007
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 4.00 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h

NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 36
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 4.00 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h

NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.

CONF 009
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 37
A318/A319/A320/A321
SERVICE BULLETIN

(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

PREPARATION
Job Set-up 0.50 h
Aircraft/System Configuration 1.00 h
Remove/Open for Access to FWD Electronics Rack 90VU 1.00 h
Remove/Open for Access to Rear Panel 120VU 1.50 h
PROCEDURE
Modify the Equipment and the Wiring in Shelf 93VU 2.00 h
Install the Equipment and the Wiring in Aft Electronics Rack 4.00 h
80VU
Install the Wiring between Aft Electronics Rack 80VU and 1.00 h
FWD Electronics Rack 90VU
Modify the Equipment and the Wiring in Rear C/B Panel 2.00 h
121VU
Install the Wiring between Rear C/B Panel 121VU and Aft 1.00 h
Electronics Rack 80VU
PREPARATION FOR TEST
Job Set-up 0.50 h
Voltage Check 0.50 h
TEST
Preliminary Test 0.50 h
Test 0.50 h
CLOSE-UP
Install/Close Items Removed/Opened for access to Rear 1.50 h
Panel 120VU
Install/Close for Access to FWD Electronics Rack 90VU 1.50 h
Close-up 1.00 h
TOTAL MAN-HOURS 20.00 h
ELAPSED TIME (HOURS) 11.00 h

NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix MANPOWER GANTT CHART.

CONF ALL
H. WEIGHT AND BALANCE
CONF 001 005
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
Manufacturer's Empty Weight +0.3 kg (+0.661 lb)
Effect on Balance +1.7 kg.m (+12.296 lb.ft)
CONF 002 006-009
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 38
A318/A319/A320/A321
SERVICE BULLETIN

Manufacturer's Empty Weight +0.4 kg (+0.882 lb)


Effect on Balance +2.3 kg.m (+16.636 lb.ft)
CONF 003 004
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
Manufacturer's Empty Weight +0.3 kg (+0.661 lb)
Effect on Balance +2.3 kg.m (+16.636 lb.ft)
CONF ALL
I. ELECTRICAL LOAD DATA
CONF 001 005
Not changed
CONF 002-004 006-009
(1) Alternating Current (AC) Load Changes
Not Changed
(2) Direct Current (DC) Load Changes
The values listed in the table(s) show the increase (+) or decrease (-) of the electrical
load resulting from the accomplishment of this Service Bulletin.
(a) Circuit Breaker Data

Busbar: 103PP ATA/SubATA: 31-38 Panel 121VU


Circuit Breaker: 14TD New
Designation: PDL/PWR/SPLY
Nominal Power (Differential Value): +100W
Intermittent: NO Sheddable: NO Clipped: NO
Effect on Electrical Loads

Flight Configuration Value (W) Operational Value (W) Max


Ground +100 +100
Start 0 0
Roll 0 0
Take Off 0 0
Climb 0 0
Cruise 0 0
Descent 0 0
Landing 0 0
Taxi 0 0
CONF ALL
J. REFERENCES

ON A/C 00357

CONCURRENT SERVICE BULLETIN (SB)


A320-34-1560 A320-46-1043

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 39
A318/A319/A320/A321
SERVICE BULLETIN

CONCURRENT SERVICE BULLETIN (SB)


A320-46-1125
ON A/C 01554, 01670, 01707, 01763, 01944, 02011, 02084, 02108, 02193, 02216, 02273,
02372, 02390, 02393, 02404, 02405, 02460, 02482, 02548, 02677, 02712, 02738, 02739,
02914, 03024, 03069

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1030
ON A/C 03246, 03356, 03361, 03374

CONCURRENT SERVICE BULLETIN (SB)


A320-46-1030
ON A/C 02742, 02744, 02754, 02765, 02769, 02779, 02803, 02818

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1030
A320-46-1126
ON A/C 03004, 03050

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1030
A320-46-1134
ON A/C 03108, 03135

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411
ON A/C 03234, 03268

CONCURRENT SERVICE BULLETIN (SB)


A320-46-1121
ON A/C 02325

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1121
ON A/C 01207

CONCURRENT SERVICE BULLETIN (SB)


A320-46-1044 A320-46-1125
ON A/C 03152

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1030
A320-46-1134
ON A/C 02495, 02565, 02578, 02605, 02636, 02646, 02691, 02715, 02777, 02782, 02795

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 40
A318/A319/A320/A321
SERVICE BULLETIN

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1411 A320-46-1030
A320-46-1126
CONF 001
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONF 002
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 41
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 12-34-24-869-002
Task 20-21-11-911-001 Task 20-21-15-912-001
Task 21-26-00-710-001 Task 22-96-00-710-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 42
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 31-38-00-740-001
Task 25-54-11-400-001
Task 31-50-00-710-001 Task 31-60-00-710-001
Task 31-50-00-710-004
Task 33-13-00-710-001 Task 33-14-00-710-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 003
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 22-96-00-710-001 Task 22-97-00-710-001
Task 24-38-51-000-001 Task 24-41-00-861-002
Task 24-38-51-400-001
Task 25-13-41-000-002 Task 25-54-11-000-001
Task 25-13-41-400-002 Task 25-54-11-400-001
Task 28-22-00-710-002 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 33-13-00-710-001
Task 33-14-00-710-001 Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-52-10 20-52-21

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 43
A318/A319/A320/A321
SERVICE BULLETIN

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-54-50 20-55-00
20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
(2) Additional work for Aircraft Modified by the original issue of this Service
Bulletin
(a) Task set A320-A-31-XX-1583-02000-93AA-A Additional work for Aircraft Modified
by the original issue of this Service Bulletin

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 12-34-24-869-002
Task 20-21-11-911-001 Task 20-21-15-912-001
Task 21-26-00-710-001 Task 22-96-00-710-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 28-22-00-710-002
Task 25-54-11-400-001
Task 31-50-00-710-001 Task 31-60-00-710-001
Task 31-50-00-710-004
Task 33-13-00-710-001 Task 33-14-00-710-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 004
(1) Modification

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 44
A318/A319/A320/A321
SERVICE BULLETIN

(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 22-96-00-710-001 Task 22-97-00-710-001
Task 24-38-51-000-001 Task 24-41-00-861-002
Task 24-38-51-400-001
Task 25-13-41-000-002 Task 25-54-11-000-001
Task 25-13-41-400-002 Task 25-54-11-400-001
Task 28-22-00-710-002 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 33-13-00-710-001
Task 33-14-00-710-001 Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-52-10 20-52-21
20-54-50 20-55-00
20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 005
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 45
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONF 006
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 46
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 007
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 47
A318/A319/A320/A321
SERVICE BULLETIN

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 008
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 48
A318/A319/A320/A321
SERVICE BULLETIN

WEIGHT AND BALANCE MANUAL (WBM)


STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF 009
(1) Modification
(a) Task set A320-A-31-XX-1583-01000-93AA-A Modification

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 06-31-53, Page Block 001
06-41-53, Page Block 001 Task 11-00-00-400-002
Task 12-34-24-869-002 Task 20-21-11-911-001
Task 20-21-15-912-001 Task 21-26-00-710-001
Task 21-63-34-000-001 Task 22-96-00-710-001
Task 21-63-34-400-001
Task 22-97-00-710-001 Task 24-38-51-000-001
Task 24-38-51-400-001
Task 24-41-00-861-002 Task 25-13-41-000-002
Task 25-13-41-400-002
Task 25-54-11-000-001 Task 27-94-34-000-001
Task 25-54-11-400-001 Task 27-94-34-400-001
Task 31-38-00-740-001 Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001 Task 32-31-71-000-001
Task 32-31-71-400-001
Task 33-13-00-710-001 Task 33-14-00-710-001
Task 46-21-34-000-001
Task 46-21-34-400-001

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-33-00 20-33-44
20-44-51 20-52-10
20-52-21 20-54-50
20-55-00 20-56-51

STRUCTURAL REPAIR MANUAL (SRM)


51-42-00 51-75-12
WEIGHT AND BALANCE MANUAL (WBM)
STANDARDS MANUAL (SM)
CONSUMABLE MATERIAL LIST (CML)
CONF ALL
K. PUBLICATION AFFECTED
AIRCRAFT MAINTENANCE MANUAL (AMM)

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 49
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT SCHEMATIC MANUAL (ASM)


AIRCRAFT WIRING LIST (AWL)
AIRCRAFT WIRING MANUAL (AWM)
ILLUSTRATED PART CATALOG (IPC)
L. INDUSTRY SUPPORT INFORMATION
Industry Support terms must be agreed between the Customer and AIRBUS in accordance
with the RFC (or RFC/RMO) procedure.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 50
A318/A319/A320/A321
SERVICE BULLETIN

2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Part kit 311583A03R03 1
Part kit 311583A06R00 1
Components See SB
CONF 002
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A01R00 1
Part kit 311583A04R02 1
Part kit 311583A06R00 1
Components See SB
Spare parts See SB
Material for task set A320-A-31-XX-1583-02000-93AA-A Additional work for
Aircraft Modified by the original issue of this Service Bulletin

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A10R00 1
Components See SB
CONF 003
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A02R00 1
Part kit 311583A05R01 1
Components See SB
Spare parts See SB
Material for task set A320-A-31-XX-1583-02000-93AA-A Additional work for
Aircraft Modified by the original issue of this Service Bulletin

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A10R00 1
Components See SB

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 51
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A05R01 1
Part kit 311583A07R00 1
Components See SB
Spare parts See SB
CONF 005
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Part kit 311583A03R03 1
Part kit 311583A06R00 1
Components See SB
CONF 006
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A04R02 1
Part kit 311583A06R00 1
Part kit 311583A07R00 1
Components See SB
Spare parts See SB
CONF 007
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A04R02 1
Part kit 311583A06R00 1
Part kit 311583A08R00 1
Components See SB
Spare parts See SB
CONF 008
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A04R02 1
Part kit 311583A06R00 1
Part kit 311583A09R00 1
Components See SB

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 52
A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY SEE NOTES


Spare parts See SB
CONF 009
Material for task set A320-A-31-XX-1583-01000-93AA-A Modification

MATERIAL QTY SEE NOTES


Consumables See SB
Part kit 311583A04R02 1
Part kit 311583A06R00 1
Part kit 311583A09R00 1
Components See SB
Spare parts See SB
CONF ALL
B. TOOLING
No tools
C. CONSUMABLES
CONF 002
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
Consumables for task set A320-A-31-XX-1583-02000-93AA-A Additional work for
Aircraft Modified by the original issue of this Service Bulletin

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 003
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
Consumables for task set A320-A-31-XX-1583-02000-93AA-A Additional work for
Aircraft Modified by the original issue of this Service Bulletin

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 004
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 53
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 007
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 008
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 009
Consumables for task set A320-A-31-XX-1583-01000-93AA-A Modification

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES


Top Coat Polyurethane -
04JMD9
Decorative Furnishing
CONF 001 005
No consumables
CONF ALL
D. LIST OF NEW PARTS
CONF 002
Part kit 311583A01R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


1 D11311800A00 1 PLACARD

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 54
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


2 ASNA2080G04 5 BUTTON
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 003
Part kit 311583A02R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


1 D00411926A00 1 PLACARD
2 ASNA2080G04 5 BUTTON
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 001 005
Part kit 311583A03R03

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


12 E0734E17FSN 1 CONNECTR

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 55
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


13 NSA937901M22-02 1 MODULE
14 NSA937901E5 1 LABEL
D9000095499995 1 BUNDLE
D9100095450095 1 PLCRDSET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 002 006-009
Part kit 311583A04R02

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


4 NSA931320-050 1 CB
12 E0734E17FSN 1 CONNECTR
13 NSA937901M22-02 1 MODULE
14 NSA937901E5 1 LABEL
15 NSA937901MA2204 1 MODULE
16 NSA937901E1 2 LABEL
17 NSA937901FM 2 MODULE
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 003 004
Part kit 311583A05R01

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 56
A318/A319/A320/A321
SERVICE BULLETIN

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


4 NSA931320-050 1 CB
D9001095400296 1 BUNDLE
D9100095450095 1 PLCRDSET
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 001 002 005-009
Part kit 311583A06R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


5 NSA938005-18 1 CAP
6 NAS1101-04-5 2 SCREW
7 MS21042-06 1 NUT
8 NAS1149FN616P 1 WASHER
9 NAS1101-06-7 1 SCREW
10 MS21042-04 2 NUT
11 NAS1149FN416P 2 WASHER
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 57
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004 006


Part kit 311583A07R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


1 D00414089A00 1 PLACARD
2 ASNA2080G04 5 BUTTON
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 007
Part kit 311583A08R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


1 D00411993A00 1 PLACARD
2 ASNA2080G04 5 BUTTON
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 58
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008 009


Part kit 311583A09R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


1 D11311721A00 1 PLACARD
2 ASNA2080G04 5 BUTTON
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
CONF 002 003
Part kit 311583A10R00

Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.

Procurement address  
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:

- AIRBUS Upgrade Services


- Attn. Sales Manager

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


D9001095405095 1 BUNDLE
CONF 001
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 59
A318/A319/A320/A321
SERVICE BULLETIN

Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 520 TIE (1)
NSA935401-08 520 TIE (1)
NSA935401-13 520 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 002
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 750 TIE (1)
NSA935401-08 750 TIE (1)
NSA935401-13 750 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 60
A318/A319/A320/A321
SERVICE BULLETIN

Components for task set A320-A-31-XX-1583-02000-93AA-A Additional work for


Aircraft Modified by the original issue of this Service Bulletin

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 180 TIE (1)
NSA935401-08 180 TIE (1)
NSA935401-13 180 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 003
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 450 TIE (1)
NSA935401-08 450 TIE (1)
NSA935401-13 450 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 61
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Components for task set A320-A-31-XX-1583-02000-93AA-A Additional work for
Aircraft Modified by the original issue of this Service Bulletin

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 180 TIE (1)
NSA935401-08 180 TIE (1)
NSA935401-13 180 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 004
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 450 TIE (1)
NSA935401-08 450 TIE (1)

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 62
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-13 450 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 005
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 520 TIE (1)
NSA935401-08 520 TIE (1)
NSA935401-13 520 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 006
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 63
A318/A319/A320/A321
SERVICE BULLETIN

For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 750 TIE (1)
NSA935401-08 750 TIE (1)
NSA935401-13 750 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 007
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 750 TIE (1)
NSA935401-08 750 TIE (1)
NSA935401-13 750 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 008
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 64
A318/A319/A320/A321
SERVICE BULLETIN

Customer Order Fulfilment


Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 750 TIE (1)
NSA935401-08 750 TIE (1)
NSA935401-13 750 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF 009
Components for task set A320-A-31-XX-1583-01000-93AA-A Modification

Procurement address  
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
AIRBUS Material, Logistics and Suppliers Standard Parts
Customer Order Fulfilment
Phone: +49 (0) 40 50 76 40 02
E-mail: Please contact your Single Point Of Contact (SPOC)
Internet: http://spares.airbus.com or via SPEC2000
For standard hardware the purchase order must be addressed to AIRBUS at the
address given above. Quote the number of this Service Bulletin, the MSN and, if
applicable the Retrofit Information Letter (RIL) reference.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


NSA935401-05 750 TIE (1)
NSA935401-08 750 TIE (1)
NSA935401-13 750 TIE (1)
NOTE(S)
Refer to the AIRBUS Ref. SM if you find part numbers of hardware components which
you cannot identify. The SM will give you the correct part number to part number
relationship.
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
CONF ALL
E. LIST OF EXISTING PARTS
CONF 002
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 65
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311460A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 003
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

DESCRIPTION OLD PART No. SEE NOTES


PLACARD 002046-64 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 004
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311260A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 006
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311260A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 007
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311272A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 008
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 66
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311461A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 009
Spare parts for task set A320-A-31-XX-1583-01000-93AA-A Modification

DESCRIPTION OLD PART No. SEE NOTES


PLACARD D11311461A00 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 001 005
No parts

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 67
A318/A319/A320/A321
SERVICE BULLETIN

CONF ALL
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A320-A-31-XX-1583-01000-93AA-A (A320-A-31-XX-1583-01ZZZ-93AZ-A)
Modification

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL


WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATION


Task Manpower
CONF 001
TOTAL MAN-HOURS 13.00 h
CONF 002
TOTAL MAN-HOURS 20.00 h
CONF 003
TOTAL MAN-HOURS 14.50 h
CONF 004
TOTAL MAN-HOURS 14.50 h
CONF 005
TOTAL MAN-HOURS 13.00 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 68
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006
TOTAL MAN-HOURS 20.00 h
CONF 007
TOTAL MAN-HOURS 20.00 h
CONF 008
TOTAL MAN-HOURS 20.00 h
CONF 009
TOTAL MAN-HOURS 20.00 h
CONF 001
ELAPSED TIME (HOURS) 13.00 h
CONF 002
ELAPSED TIME (HOURS) 11.00 h
CONF 003
ELAPSED TIME (HOURS) 14.00 h
CONF 004
ELAPSED TIME (HOURS) 14.00 h
CONF 005
ELAPSED TIME (HOURS) 13.00 h
CONF 006
ELAPSED TIME (HOURS) 11.00 h
CONF 007
ELAPSED TIME (HOURS) 11.00 h
CONF 008
ELAPSED TIME (HOURS) 11.00 h
CONF 009
ELAPSED TIME (HOURS) 11.00 h
CONF ALL
B. PREPARATION
(1) Task A320-A-31-XX-1583-01003-540A-A (A320-A-31-XX-1583-01ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 12-34-24-869-002
AMM
Task 25-54-11-000-001
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 69
A318/A319/A320/A321
SERVICE BULLETIN

(b) Remove the partition panels (Panel 131CW, Panel 131DW and Panel 132EW)
from the FWD cargo compartment, at Frame 24A for access, refer to Ref. AMM
Task 25-54-11-000-001.
(2) Task A320-A-31-XX-1583-04002-540A-A (A320-A-31-XX-1583-04ZZZ-540Z-A)
Aircraft/System Configuration
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-38-51-000-001
Procedure
(a) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(b) Put the warning notices in position on the external power receptacle to tell
persons not to connect an external power source.
(c) Make sure that the EMER EXIT LT pushbutton switch on the overhead CTL & IND
panel (Electrical Panel 25VU) is set to the OFF position.
(d) In the cockpit, on the ELEC panel (Electrical Panel 35VU), release the BAT
pushbutton switches.
(e) Put a warning notice in position on the ELEC panel (Electrical Panel 35VU) to tell
persons not to operate the batteries.
(f) Put a warning notice in position on the refuel/defuel control panel (Electrical
Panel 800VU) to tell persons not to operate the NORMAL BATTERY switch.
(g) Put a warning notice in position in the cockpit to tell persons not to start the
Auxiliary Power Unit (APU).
(h) Put a warning notice in position in the cockpit to tell persons not to start ENG 1
and ENG 2.
(i) Disconnect the battery connectors:
1 Do the job set-up procedure as specified in the removal of the batteries,
refer to Ref. AMM Task 24-38-51-000-001.
2 Turn the knurled nut a quarter turn.
3 Disconnect the connectors.
4 Put the blanking caps on the disconnected electrical connectors.
CONF 001 002 005-009
(3) Task A320-A-31-XX-1583-02001-540A-A (A320-A-31-XX-1583-02ZZZ-540Z-A)
Remove/Open for Access to FWD Electronics Rack 90VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.00 h

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 70
A318/A319/A320/A321
SERVICE BULLETIN

Minimum Number of person 1


Elapsed Time 1.00 h
Skills Electrical

Referenced Information

Manuals/Drawings References/Sheets
Task 21-63-34-000-001
AMM Task 27-94-34-000-001
Task 32-31-71-000-001
Procedure
(a) Remove the shelf (Electrical Panel 93VU).
1 Remove and retain SEC-3 (FIN 1CE3) from the shelf (Electrical Panel 93VU)
for access, refer to Ref. AMM Task 27-94-34-000-001.
2 Remove and retain the zone controller (FIN 8HK) (if installed) from the shelf
(Electrical Panel 93VU) for access, refer to Ref. AMM Task 21-63-34-000-
001.
3 Remove and retain LGCIU-1 (FIN 5GA1) from the shelf (Electrical Panel
93VU) for access, refer to Ref. AMM Task 32-31-71-000-001.
4 Put the blanking caps on the disconnected connectors.
5 Disconnect the bonding braid.
6 Remove the attachment hardware from the shelf.

NOTE: You must retain the hardware.

7 Remove the shelf (Electrical Panel 93VU) and install it on bench.


CONF 002-004 006-009
(4) Task A320-A-31-XX-1583-03001-540A-A (A320-A-31-XX-1583-03ZZZ-540Z-A)
Remove/Open for Access to Rear Panel 120VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM 06-41-53, Page Block 001
Task 20-21-15-912-001
Task 25-13-41-000-002
SRM 51-42-00
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 71
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
5 Tag all the parts you must remove and retain to make the subsequent
installation easier.
6 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
7 To torque tighten the electrical component fasteners, refer to Ref. AMM
Task 20-21-15-912-001.
(b) Remove the sidewall panels (Panel 212HW, Panel 212JW and Panel 212KW) from
the cockpit for access, refer to Ref. AMM Task 25-13-41-000-002.
(c) Remove the panel from the cockpit in accordance with Ref. SRM 51-42-00 and
refer to Ref. Fig. Removal/Installation of the Access Panel from/in the Cockpit (For
Access).
1 Remove as shown in view A and B:

1 PANEL-RH LATERAL   Item (40) Retain


attached with

2 SCREW   Item (41) Retain

1 SCREW   Item (42) Retain


(d) Remove the stowage box from the right aft console, in the cockpit in accordance
with Ref. SRM 51-42-00 and refer to Ref. Fig. Removal of the Stowage Box from
the Right Aft Console, in the Cockpit (For Access).
1 Remove as shown in view A and B:

1 MODULE ASSY 702VU   Item (43) Retain


attached with

4 SCREW   Item (48) Retain

1 SCREW   Item (47) Retain

2 SCREW   Item (44) Retain

4 WASHER   Item (49) Retain

2 WASHER   Item (45) Retain

1 WASHER   Item (46) Retain


2 Remove as shown in view A and C:

1 BOX ASSY-STOWAGE   Item (51) Retain


attached with

4 SCREW   Item (50) Retain

2 SCREW   Item (48) Retain

2 WASHER   Item (49) Retain

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 72
A318/A319/A320/A321
SERVICE BULLETIN

(e) Remove the right aft console (Electrical Panel 702VU) from the cockpit in
accordance with Ref. SRM 51-42-00 and refer to Ref. Fig. Removal/Installation of
Right Aft Console 702VU from/in the Cockpit (For Access).
1 Remove as shown in view A:

1 STRUCTURE   Item (54) Retain


attached with

6 SCREW   Item (53) Retain

6 WASHER   Item (52) Retain

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 73
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

A
Z210

FR12

FR1
B

(41)

(40)

(42)

(41)
ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of the Access A320-31-1583
REV 05 Apr 09/21 Panel from/in the Cockpit (For Access) Page 74
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

C
(46)
(47)
(48)
A
(44) 702VU
(45)

(49)

(43)

ICN-A320-A-31XX1583-A-FAPE3-01RH9-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH9-A-001-01 SHEET 1/2


REV 00 Dec 12/19 Removal of the Stowage Box from the Right A320-31-1583
REV 05 Apr 09/21 Aft Console, in the Cockpit (For Access) Page 75
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

(50)

(50)

(51)

(48)

(49)

ICN-A320-A-31XX1583-A-FAPE3-01RHA-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHA-A-001-01 SHEET 2/2


REV 00 Dec 12/19 Removal of the Stowage Box from the Right A320-31-1583
REV 05 Apr 09/21 Aft Console, in the Cockpit (For Access) Page 76
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

(52)
(53)

(53)

(54) (52)

(53)

(52)
(53)

(52)

A
702VU
ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of Right Aft Console A320-31-1583
REV 05 Apr 09/21 702VU from/in the Cockpit (For Access) Page 77
A318/A319/A320/A321
SERVICE BULLETIN

CONF ALL
C. PROCEDURE
CONF 001 005
(1) Task A320-A-31-XX-1583-01001-920A-A (A320-A-31-XX-1583-01ZZZ-920Z-A)
Modify the Equipment and the Wiring in Shelf 93VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Work location Electrical Panel 93VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A03R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
13 NSA937901M22-02 1 MODULE
14 NSA937901E5 1 LABEL
D9000095499995 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 20 TIE (1)
NSA935401-08 20 TIE (1)
NSA935401-13 20 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
20-33-00
20-33-44
20-44-51
ESPM
20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 78
A318/A319/A320/A321
SERVICE BULLETIN

2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Modify the terminal block (FIN 219VT) in the shelf (Electrical Panel 93VU), refer
to Ref. ESPM 20-44-51 and Ref. Fig. Modification of Terminal Block 219VT in Shelf
93VU.
1 Loosen the end clamps at each end of the terminal block.
2 Install at position 5 as shown in view A thru C:

FIN 219VT5
1 MODULE NSA937901M22-02 Item 13

1 LABEL IDENTIFICATION NSA937901E5 Item 14


3 Tighten the end clamps at each end of the terminal block.
(c) Modify the wiring in the shelf (Electrical Panel 93VU).
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WD and Ref. Fig. HD.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WD and Ref. Fig. HD, supplied in:

1 BUNDLE D9000095499995  
(d) Attach the wires with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

20 TIE-CABLE NSA935401-05  
or

20 TIE-CABLE NSA935401-08  
or

20 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 79
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

Z120

A
FR24

FR1

A
90VU
ICN-A320-A-31XX1583-A-FAPE3-01P70-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P70-A-001-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of Terminal Block 219VT in Shelf 93VU
REV 05 Apr 09/21 Page 80
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

14

B
93VU

EXISTING
END CLAMP

13
219VT5

C
EXISTING 219VT
END CLAMP
ICN-A320-A-31XX1583-A-FAPE3-01P71-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P71-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of Terminal Block 219VT in Shelf 93VU
REV 05 Apr 09/21 Page 81
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

BEFORE AFTER

AB AB 5
13E 0147 G
13E 0147 22 F.R.
- F.R. P 0296 22 F.R.
- F.R. 283VC A
283VC A
5GA1 LGCIU-1
5GA1 LGCIU-1
Y 0303 70 F.R.
93VU 121
219VT 281VC A

93VU 121

NEW WIRE DELETED WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RE4-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE4-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WDAA
REV 05 Apr 09/21 Page 82
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 93VU 5GA1-AB 13E 3138-0147 1M CF24 93VU 283VC 22 D

2 93VU 219VT 5G EN3155-016M2222 3138-0147 1M CF24 2000 80 93VU 5GA1-AB 13E E0170FA2200 (a) A (b) (1)

3 93VU 219VT 5P EN3155-016M2222 3138-0296 1M CF24 1000 40 93VU 283VC 22 EN3155-008M2222 (a) A (b) (1)

4 93VU 219VT 5Y EN3155-016M2222 3138-0303 1M CF24 1500 60 93VU 281VC 70 EN3155-008M2222 (a) A (b) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE (1) = (a) = BUNDLE D9000095499995 OR


D = DELETED WIRE (b) = BUNDLE D9001095400196

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE9-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HDAA
REV 05 Apr 09/21 Page 83
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009


(1) Task A320-A-31-XX-1583-01002-920A-A (A320-A-31-XX-1583-01ZZZ-920Z-A)
Modify the Equipment and the Wiring in Shelf 93VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Work location Electrical Panel 93VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
13 NSA937901M22-02 1 MODULE
14 NSA937901E5 1 LABEL
D9001095400196 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 20 TIE (1)
NSA935401-08 20 TIE (1)
NSA935401-13 20 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
20-33-00
20-33-44
20-44-51
ESPM
20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 84
A318/A319/A320/A321
SERVICE BULLETIN

3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Modify the terminal block (FIN 219VT) in the shelf (Electrical Panel 93VU), refer
to Ref. ESPM 20-44-51 and Ref. Fig. Modification of Terminal Block 219VT in Shelf
93VU.
1 Loosen the end clamps at each end of the terminal block.
2 Install at position 5, as shown in view A thru C:

FIN 219VT5
1 MODULE NSA937901M22-02 Item 13

1 LABEL IDENTIFICATION NSA937901E5 Item 14


3 Tighten the end clamps at each end of the terminal block.
(c) Modify the wiring in the shelf (Electrical Panel 93VU).
1 Remove the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WD and Ref. Fig. HD.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WD and Ref. Fig. HD, supplied in:

1 BUNDLE D9001095400196  
(d) Attach the wires with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

20 TIE-CABLE NSA935401-05  
or

20 TIE-CABLE NSA935401-08  
or

20 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 85
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

Z120

A
FR24

FR1

A
90VU
ICN-A320-A-31XX1583-A-FAPE3-01P70-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P70-A-001-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of Terminal Block 219VT in Shelf 93VU
REV 05 Apr 09/21 Page 86
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

14

B
93VU

EXISTING
END CLAMP

13
219VT5

C
EXISTING 219VT
END CLAMP
ICN-A320-A-31XX1583-A-FAPE3-01P71-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P71-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of Terminal Block 219VT in Shelf 93VU
REV 05 Apr 09/21 Page 87
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

BEFORE AFTER

AB AB 5
13E 0147 G
13E 0147 22 F.R.
- F.R. P 0296 22 F.R.
- F.R. 283VC A
283VC A
5GA1 LGCIU-1
5GA1 LGCIU-1
Y 0303 70 F.R.
93VU 121
219VT 281VC A

93VU 121

NEW WIRE DELETED WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RE4-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE4-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WDAA
REV 05 Apr 09/21 Page 88
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 93VU 5GA1-AB 13E 3138-0147 1M CF24 93VU 283VC 22 D

2 93VU 219VT 5G EN3155-016M2222 3138-0147 1M CF24 2000 80 93VU 5GA1-AB 13E E0170FA2200 (a) A (b) (1)

3 93VU 219VT 5P EN3155-016M2222 3138-0296 1M CF24 1000 40 93VU 283VC 22 EN3155-008M2222 (a) A (b) (1)

4 93VU 219VT 5Y EN3155-016M2222 3138-0303 1M CF24 1500 60 93VU 281VC 70 EN3155-008M2222 (a) A (b) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE (1) = (a) = BUNDLE D9000095499995 OR


D = DELETED WIRE (b) = BUNDLE D9001095400196

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE9-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HDAA
REV 05 Apr 09/21 Page 89
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001
(2) Task A320-A-31-XX-1583-01001-720A-A (A320-A-31-XX-1583-01ZZZ-720Z-A)
Install the Equipment and the Wiring in Aft Electronics Rack 80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Manpower/Resources/Skills

Man-hours 3.50 h
Minimum Number of person 1
Elapsed Time 3.50 h
Skills Electrical
Material necessary to do the job
Part kit 311583A03R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
12 E0734E17FSN 1 CONNECTR
D9000095499995 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A06R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 NSA938005-18 1 CAP
6 NAS1101-04-5 2 SCREW
7 MS21042-06 1 NUT
8 NAS1149FN616P 1 WASHER
9 NAS1101-06-7 1 SCREW
10 MS21042-04 2 NUT
11 NAS1149FN416P 2 WASHER

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 350 TIE (1)
NSA935401-08 350 TIE (1)
NSA935401-13 350 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
06-41-53, Page Block 001
Task 11-00-00-400-002

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 90
A318/A319/A320/A321
SERVICE BULLETIN

Manuals/Drawings References/Sheets
Task 46-21-34-000-001
Task 46-21-34-400-001
20-33-00
20-33-44
20-52-10
ESPM
20-52-21
20-54-50
20-56-51
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
6 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
7 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
8 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
9 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
10 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
11 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Install the connector in the aft electronics rack (Electrical Panel 80VU), refer to
Ref. Fig. Installation of the Equipment in Aft Electronics Rack 80VU.
1 Install as shown in view A and B:

FIN 183VC
1 CONNECTOR E0734E17FSN Item 12
and attach with

2 SCREW NAS1101-04-5 Item 6

2 WASHER NAS1149FN416P Item 11

2 NUT MS21042-04 Item 10


2 Install as shown in view A and B:

1 CAP NSA938005-18 Item 5


and attach with

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 91
A318/A319/A320/A321
SERVICE BULLETIN

1 SCREW NAS1101-06-7 Item 9

1 WASHER NAS1149FN616P Item 8

1 NUT MS21042-06 Item 7


3 Bond the placards identified ATSU DATA LOADER and 183VC as shown in
view A thru D, supplied in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Remove and retain the ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-000-
001.
(d) Install the wiring in the aft electronics rack (Electrical Panel 80VU).
Refer to Ref. ESPM 20-33-00
1 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC, supplied in:

1 BUNDLE D9000095499995  
(e) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

350 TIE-CABLE NSA935401-05  


or

350 TIE-CABLE NSA935401-08  


or

350 TIE-CABLE NSA935401-13  


(f) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(g) Install the retained ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-400-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 92
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001

FR24

Z120

10
FR1
183VC
12
C A
80VU B
7

11
6
5

D
8
9

PLACARD
B
PLACARD

ATSU
DATA LOADER
183VC

C D
ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
Installation of the Equipment in Aft Electronics Rack 80VU
REV 05 Apr 09/21 Page 93
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001

AFTER
11
F.R. G
P 0297 CF22 37
Y
1822VT
127 F.R.
82VU 0298 CF22 38
DC1

983VG
127
187VU B1 0299 CF22 21
F.R.
3785VN
127
83VU

0300 28
0301
F.R.
B1

979VG
127

LOADING PLUG
187VU
AB
8G R 23
7156
WX26
8H B 39
- F.R.

AA
9C R 6
7157
WX26
9D B 7
- F.R.

1TX1 ATSU-1
127 81VU

14
M 0302 19
F.R. -
1813VT
127
81VU

F.R. 50 0305 18
A 64VC
128 80VU 183VC A
80VU 127

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE

ICN-A320-A-31XX1583-A-FAPE3-01P7C-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P7C-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WCAA
REV 05 Apr 09/21 Page 94
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 50 EN3155-014M2018 3138-0305 1M CF24 9500 380 80VU 183VC 18 E0685LE2200 (a) A (b) (1)

2 80VU 183VC 37 E0685LE2200 3138-0297 1M CF22 7500 300 82VU 1822VT 11P EN3155-016M2222 (a) A (b) (1)

3 80VU 183VC 38 E0685LE2200 3138-0298 1M CF22 4000 160 187VU 983VG GND EN3155-015F2018 (a) A (b) (1)

4 80VU 183VC 21 E0685LE2200 3138-0299 1M CF22 6000 240 83VU 3785VN GND NSA936501TA2206 (a) A (b) (1)

5 80VU 183VC 28 E0685LE2200 3138-0300 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A (b) (1)

6 80VU 183VC 19 E0685LE2200 3138-0302 1M CF24 5500 220 81VU 1813VT 14M EN3155-016M2222 (a) A (b) (1)

7 80VU 183VC SH E0718-02-30 3138G7156 1M WX26 6000 240 81VU 1TX1-AB SH E0718-02-30 (a) A (b) (1)

8 80VU 183VC 39 E0685LE2200 3138-7156 B 1M WX26 6000 240 81VU 1TX1-AB 8H E0170FA2200 (a) A (b) (1)

9 80VU 183VC 23 E0685LE2200 3138-7156 R 1M WX26 6000 240 81VU 1TX1-AB 8G E0170FA2200 (a) A (b) (1)

10 80VU 183VC SH E0718-02-30 3138G7157 1M WX26 6000 240 81VU 1TX1-AA SH E0718-02-30 (a) A (b) (1)

11 80VU 183VC 7 E0685LE2200 3138-7157 B 1M WX26 6000 240 81VU 1TX1-AA 9D E0170FA2200 (a) A (b) (1)

12 80VU 183VC 6 E0685LE2200 3138-7157 R 1M WX26 6000 240 81VU 1TX1-AA 9C E0170FA2200 (a) A (b) (1)

13 80VU 3138G7157 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 80VU 3138G7156 W.F. E0160-1-0H (a) A (b) (1)

14 80VU 3138G7156 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A (b) (1)

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE (1) = (a) = BUNDLE D9000095499995 OR


SH = SHIELD (b) = BUNDLE D9001095400196
W.F. = WIRE FERRULE GND = GROUND

Figure ICN-A320-A-31XX1583-A-FAPE3-01P7B-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HCAA
REV 05 Apr 09/21 Page 95
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009


(2) Task A320-A-31-XX-1583-01002-720A-A (A320-A-31-XX-1583-01ZZZ-720Z-A)
Install the Equipment and the Wiring in Aft Electronics Rack 80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
12 E0734E17FSN 1 CONNECTR
15 NSA937901MA2204 1 MODULE
16 NSA937901E1 2 LABEL
17 NSA937901FM 2 MODULE
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A06R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 NSA938005-18 1 CAP
6 NAS1101-04-5 2 SCREW
7 MS21042-06 1 NUT
8 NAS1149FN616P 1 WASHER
9 NAS1101-06-7 1 SCREW
10 MS21042-04 2 NUT
11 NAS1149FN416P 2 WASHER

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 390 TIE (1)
NSA935401-08 390 TIE (1)
NSA935401-13 390 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 96
A318/A319/A320/A321
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
AMM
Task 11-00-00-400-002
Task 46-21-34-000-001
Task 46-21-34-400-001
20-33-00
20-33-44
20-44-51
ESPM 20-52-10
20-52-21
20-54-50
20-56-51
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
6 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
7 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
8 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
9 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
10 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
11 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Install the connector in the aft electronics rack (Electrical Panel 80VU), refer to
Ref. Fig. Installation of the Equipment in Aft Electronics Rack 80VU.
1 Install as shown in view A and B:

FIN 183VC
1 CONNECTOR E0734E17FSN Item 12
and attach with

2 SCREW NAS1101-04-5 Item 6

2 WASHER NAS1149FN416P Item 11

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 97
A318/A319/A320/A321
SERVICE BULLETIN

2 NUT MS21042-04 Item 10


2 Install as shown in view A and B:

1 CAP NSA938005-18 Item 5


and attach with

1 SCREW NAS1101-06-7 Item 9

1 WASHER NAS1149FN616P Item 8

1 NUT MS21042-06 Item 7


3 Bond the placards identified ATSU DATA LOADER and 183VC as shown in
view A thru D, supplied in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the terminal block (FIN 1822VT) (if necessary) in the aft electronics rack
(Electrical Panel 80VU), refer to Ref. ESPM 20-44-51 and Ref. Fig. Modification of
Terminal Block 1822VT in Aft Electronics Rack 80VU.
1 Loosen the end clamps at each end of the terminal block.
2 If necessary, install at position 9 as shown in view A and B:

FIN 1822VT9
1 MODULE-FALSE NSA937901FM Item 17
3 If necessary, install at position 10 as shown in view A and B:

FIN 1822VT10
1 MODULE-FALSE NSA937901FM Item 17
4 If necessary, install at position 11 as shown in view A and B:

FIN 1822VT11
1 MODULE NSA937901MA2204 Item 15

2 LABEL IDENTIFICATION NSA937901E1 Item 16


5 Tighten the end clamps at each end of the terminal block.
(d) Remove and retain the ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-000-
001.
(e) Install the wiring in the aft electronics rack (Electrical Panel 80VU).
Refer to Ref. ESPM 20-33-00
1 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC
- Ref. Fig. WG and Ref. Fig. HG, supplied in:

1 BUNDLE D9001095400196  
(f) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

390 TIE-CABLE NSA935401-05  


or

390 TIE-CABLE NSA935401-08  


REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 98
A318/A319/A320/A321
SERVICE BULLETIN

or

390 TIE-CABLE NSA935401-13  


(g) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(h) Install the retained ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-400-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 99
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

FR24

Z120

10
FR1
183VC
12
C A
80VU B
7

11
6
5

D
8
9

PLACARD
B
PLACARD

ATSU
DATA LOADER
183VC

C D
ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
Installation of the Equipment in Aft Electronics Rack 80VU
REV 05 Apr 09/21 Page 100
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

A
Z120

FR24

FR1

A
80VU

EXISTING 1822VT9
END CLAMP 17

1822VT10 16
17
16

1822VT11
15
EXISTING
END CLAMP

B
1822VT

ICN-A320-A-31XX1583-A-FAPE3-01P72-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P72-A-002-01 SHEET 1/1


REV 00 Dec 12/19 Modification of Terminal Block A320-31-1583
REV 05 Apr 09/21 1822VT in Aft Electronics Rack 80VU Page 101
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

AFTER
11
F.R. G
P 0297 CF22 37
Y
1822VT
127 F.R.
82VU 0298 CF22 38
DC1

983VG
127
187VU B1 0299 CF22 21
F.R.
3785VN
127
83VU

0300 28
0301
F.R.
B1

979VG
127

LOADING PLUG
187VU
AB
8G R 23
7156
WX26
8H B 39
- F.R.

AA
9C R 6
7157
WX26
9D B 7
- F.R.

1TX1 ATSU-1
127 81VU

14
M 0302 19
F.R. -
1813VT
127
81VU

F.R. 50 0305 18
A 64VC
128 80VU 183VC A
80VU 127

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE

ICN-A320-A-31XX1583-A-FAPE3-01P7C-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01P7C-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WCAA
REV 05 Apr 09/21 Page 102
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 50 EN3155-014M2018 3138-0305 1M CF24 9500 380 80VU 183VC 18 E0685LE2200 (a) A (b) (1)

2 80VU 183VC 37 E0685LE2200 3138-0297 1M CF22 7500 300 82VU 1822VT 11P EN3155-016M2222 (a) A (b) (1)

3 80VU 183VC 38 E0685LE2200 3138-0298 1M CF22 4000 160 187VU 983VG GND EN3155-015F2018 (a) A (b) (1)

4 80VU 183VC 21 E0685LE2200 3138-0299 1M CF22 6000 240 83VU 3785VN GND NSA936501TA2206 (a) A (b) (1)

5 80VU 183VC 28 E0685LE2200 3138-0300 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A (b) (1)

6 80VU 183VC 19 E0685LE2200 3138-0302 1M CF24 5500 220 81VU 1813VT 14M EN3155-016M2222 (a) A (b) (1)

7 80VU 183VC SH E0718-02-30 3138G7156 1M WX26 6000 240 81VU 1TX1-AB SH E0718-02-30 (a) A (b) (1)

8 80VU 183VC 39 E0685LE2200 3138-7156 B 1M WX26 6000 240 81VU 1TX1-AB 8H E0170FA2200 (a) A (b) (1)

9 80VU 183VC 23 E0685LE2200 3138-7156 R 1M WX26 6000 240 81VU 1TX1-AB 8G E0170FA2200 (a) A (b) (1)

10 80VU 183VC SH E0718-02-30 3138G7157 1M WX26 6000 240 81VU 1TX1-AA SH E0718-02-30 (a) A (b) (1)

11 80VU 183VC 7 E0685LE2200 3138-7157 B 1M WX26 6000 240 81VU 1TX1-AA 9D E0170FA2200 (a) A (b) (1)

12 80VU 183VC 6 E0685LE2200 3138-7157 R 1M WX26 6000 240 81VU 1TX1-AA 9C E0170FA2200 (a) A (b) (1)

13 80VU 3138G7157 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 80VU 3138G7156 W.F. E0160-1-0H (a) A (b) (1)

14 80VU 3138G7156 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A (b) (1)

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE (1) = (a) = BUNDLE D9000095499995 OR


SH = SHIELD (b) = BUNDLE D9001095400196
W.F. = WIRE FERRULE GND = GROUND

Figure ICN-A320-A-31XX1583-A-FAPE3-01P7B-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HCAA
REV 05 Apr 09/21 Page 103
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

AFTER

11
F.R. 47 0294 G
P F.R.
Y
A 64VC
128 80VU 1822VT
128
82VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLK-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLK-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WGAA
REV 05 Apr 09/21 Page 104
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 47 EN3155-014M2018 3138-0294 1M CF22 4000 160 82VU 1822VT 11G EN3155-016M2222 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLN-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HGAA
REV 05 Apr 09/21 Page 105
A318/A319/A320/A321
SERVICE BULLETIN

CONF 005
(2) Task A320-A-31-XX-1583-01013-720A-A (A320-A-31-XX-1583-01ZZZ-720Z-A)
Install the Equipment and the Wiring in Aft Electronics Rack 80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Manpower/Resources/Skills

Man-hours 3.50 h
Minimum Number of person 1
Elapsed Time 3.50 h
Skills Electrical
Material necessary to do the job
Part kit 311583A03R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
12 E0734E17FSN 1 CONNECTR
D9000095499995 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A06R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
5 NSA938005-18 1 CAP
6 NAS1101-04-5 2 SCREW
7 MS21042-06 1 NUT
8 NAS1149FN616P 1 WASHER
9 NAS1101-06-7 1 SCREW
10 MS21042-04 2 NUT
11 NAS1149FN416P 2 WASHER

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 350 TIE (1)
NSA935401-08 350 TIE (1)
NSA935401-13 350 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM
06-41-53, Page Block 001
Task 11-00-00-400-002

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 106
A318/A319/A320/A321
SERVICE BULLETIN

Manuals/Drawings References/Sheets
Task 46-21-34-000-001
Task 46-21-34-400-001
20-33-00
20-33-44
20-52-10
ESPM
20-52-21
20-54-50
20-56-51
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
5 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
6 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
7 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
8 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
9 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
10 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
11 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Install the connector in the aft electronics rack (Electrical Panel 80VU), refer to
Ref. Fig. Installation of the Equipment in Aft Electronics Rack 80VU.
1 Install as shown in view A and B:

FIN 183VC
1 CONNECTOR E0734E17FSN Item 12
and attach with

2 SCREW NAS1101-04-5 Item 6

2 WASHER NAS1149FN416P Item 11

2 NUT MS21042-04 Item 10


2 Install as shown in view A and B:

1 CAP NSA938005-18 Item 5


and attach with

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 107
A318/A319/A320/A321
SERVICE BULLETIN

1 SCREW NAS1101-06-7 Item 9

1 WASHER NAS1149FN616P Item 8

1 NUT MS21042-06 Item 7


3 Bond the placards identified ATSU DATA LOADER and 183VC as shown in
view A thru D, supplied in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Remove and retain the ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-000-
001.
(d) Install the wiring in the aft electronics rack (Electrical Panel 80VU).
Refer to Ref. ESPM 20-33-00
1 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC, supplied in:

1 BUNDLE D9000095499995  
(e) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

350 TIE-CABLE NSA935401-05  


or

350 TIE-CABLE NSA935401-08  


or

350 TIE-CABLE NSA935401-13  


(f) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(g) Install the retained ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-400-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 108
A318/A319/A320/A321
SERVICE BULLETIN

CONF 005

FR24

Z120

10
FR1
183VC
12
C A
80VU B
7

11
6
5

D
8
9

PLACARD
B
PLACARD

ATSU
DATA LOADER
183VC

C D
ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHC-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
Installation of the Equipment in Aft Electronics Rack 80VU
REV 05 Apr 09/21 Page 109
A318/A319/A320/A321
SERVICE BULLETIN

CONF 005

AFTER
36
F.R. -
B 0297 CF22 37
1822VT
127
82VU F.R.
0298 CF22 38
DC1

983VG
127
187VU B1 0299 CF22 21
F.R.
3785VN
127
83VU

0300 28
0301
F.R.
B1

979VG
127

LOADING PLUG
187VU
AB
8G R 23
7156
WX26
8H B 39
- F.R.

AA
9C R 6
7157
WX26
9D B 7
- F.R.

1TX1 ATSU-1
127 81VU

14
M 0302 19
F.R. -
1813VT
127
81VU

F.R. 50 0305 18
A 64VC
128 80VU 183VC A
80VU 127

NEW WIRE F.R. FOR REFERENCE


NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE
ICN-A320-A-31XX1583-A-FAPE3-01YFJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WCAC
REV 05 Apr 09/21 Page 110
A318/A319/A320/A321
SERVICE BULLETIN

CONF 005

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 50 EN3155-014M2018 3138-0305 1M CF24 9500 380 80VU 183VC 18 E0685LE2200 (a) A

2 80VU 183VC 37 E0685LE2200 3138-0297 1M CF22 7500 300 82VU 1822VT 36B EN3155-016M2222 (a) A

3 80VU 183VC 38 E0685LE2200 3138-0298 1M CF22 4000 160 187VU 983VG GND EN3155-015F2018 (a) A

4 80VU 183VC 21 E0685LE2200 3138-0299 1M CF22 6000 240 83VU 3785VN GND NSA936501TA2206 (a) A

5 80VU 183VC 28 E0685LE2200 3138-0300 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A

6 80VU 183VC 19 E0685LE2200 3138-0302 1M CF24 5500 220 81VU 1813VT 14M EN3155-016M2222 (a) A

7 80VU 183VC SH 3138G7156 1M WX26 6000 240 81VU 1TX1-AB SH (a) A

8 80VU 183VC 39 E0685LE2200 3138-7156 B 1M WX26 6000 240 81VU 1TX1-AB 8H E0170FA2200 (a) A

9 80VU 183VC 23 E0685LE2200 3138-7156 R 1M WX26 6000 240 81VU 1TX1-AB 8G E0170FA2200 (a) A

10 80VU 183VC SH 3138G7157 1M WX26 6000 240 81VU 1TX1-AA SH (a) A

11 80VU 183VC 7 E0685LE2200 3138-7157 B 1M WX26 6000 240 81VU 1TX1-AA 9D E0170FA2200 (a) A

12 80VU 183VC 6 E0685LE2200 3138-7157 R 1M WX26 6000 240 81VU 1TX1-AA 9C E0170FA2200 (a) A

13 80VU 3138G7157 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 80VU 3138G7156 W.F. E0160-1-0H (a) A

14 80VU 3138G7156 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (a) A

15

16

17

18

19

20

21

22

23

24

25

(a) = BUNDLE D9000095499995 W.F. = WIRE FERRULE


A = ADDED WIRE GND = GROUND
SH = SHIELD

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFM-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HCAC
REV 05 Apr 09/21 Page 111
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004


(3) Task A320-A-31-XX-1583-06002-920A-A (A320-A-31-XX-1583-06ZZZ-920Z-A)
Modify the Wiring in Aft Electronics Rack 80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Manpower/Resources/Skills

Man-hours 4.00 h
Minimum Number of person 1
Elapsed Time 4.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A05R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9001095400296 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 260 TIE (1)
NSA935401-08 260 TIE (1)
NSA935401-13 260 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-41-53, Page Block 001
AMM
Task 46-21-34-000-001
Task 46-21-34-400-001
20-33-00
20-33-44
ESPM 20-52-10
20-52-21
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 112
A318/A319/A320/A321
SERVICE BULLETIN

3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 Do a check of the electrical connectors before you connect them, refer to
Ref. ESPM 20-52-10.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Remove and retain the ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-000-
001.
(c) Modify the wiring in the aft electronics rack (Electrical Panel 80VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC
- Ref. Fig. WG and Ref. Fig. HG, supplied in:

1 BUNDLE D9001095400296  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

260 TIE-CABLE NSA935401-05  


or

260 TIE-CABLE NSA935401-08  


or

260 TIE-CABLE NSA935401-13  


(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(f) Install the retained ATSU (FIN 1TX1), refer to Ref. AMM Task 46-21-34-400-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 113
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

BEFORE AFTER

11
F.R. - P 0297 CF22 37
14 F.R. -
V 4621-0058 18
1822VT F.R.
F.R. - 127 0298 CF22 38
82VU
1813VT DC1
127
81VU 983VG
127
187VU

F.R. 47 4621-0055 19
0300 28
A 29VC
127 183VC A 0301
80VU 127 F.R.
B1

979VG
127

LOADING PLUG
187VU
AB
8G R 23
7156
WX26
8H B 39
- F.R.

AA
9C R 6
7157
WX26
9D B 7
- F.R.

1TX1 ATSU-1
127 81VU

14
V 4621-0058 19
F.R. -
1813VT
127
81VU

F.R. 47 4621-0055 18
A 29VC
127 183VC A
80VU 127

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE

ICN-A320-A-31XX1583-A-FAPE3-01RE6-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE6-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WCAB
REV 05 Apr 09/21 Page 114
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 183VC 19 4621-0055 1M CF24 127 29VC 47 M1O

2 80VU 183VC 18 E0685LE2200 4621-0055 1M CF24 127 29VC 47 M1N

3 80VU 183VC 18 4621-0058 1M CF24 81VU 1813VT 14V M1O

4 80VU 183VC 19 E0685LE2200 4621-0058 1M CF24 81VU 1813VT 14V M1N

8 80VU 183VC 37 E0685LE2200 3138-0297 1M CF22 7500 300 82VU 1822VT 11P EN3155-016M2222 (c) A

9 80VU 183VC 38 E0685LE2200 3138-0298 1M CF22 4000 160 187VU 983VG GND EN3155-015F2018 (c) A

10 80VU 183VC 28 E0685LE2200 3138-0300 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (c) A

11 80VU 183VC SH E0718-02-30 3138G7156 1M WX26 6000 240 81VU 1TX1-AB SH E0718-02-30 (c) A

12 80VU 183VC 39 E0685LE2200 3138-7156 B 1M WX26 6000 240 81VU 1TX1-AB 8H E0170FA2200 (c) A

13 80VU 183VC 23 E0685LE2200 3138-7156 R 1M WX26 6000 240 81VU 1TX1-AB 8G E0170FA2200 (c) A

14 80VU 183VC SH E0718-02-30 3138G7157 1M WX26 6000 240 81VU 1TX1-AA SH E0718-02-30 (c) A

15 80VU 183VC 7 E0685LE2200 3138-7157 B 1M WX26 6000 240 81VU 1TX1-AA 9D E0170FA2200 (c) A

16 80VU 183VC 6 E0685LE2200 3138-7157 R 1M WX26 6000 240 81VU 1TX1-AA 9C E0170FA2200 (c) A

17 80VU 3138G7157 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 80VU 3138G7156 W.F. E0160-1-0H (c) A

18 80VU 3138G7156 W.F. E0160-1-0H 3138-0301 1M CF24 4000 160 187VU 979VG GND EN3155-015F2018 (c) A

19

20

21

22

23

24

25

(c) = BUNDLE D9001095400296 M1N = NEW HOOK-UP ON END 1 GND = GROUND


A = ADDED WIRE SH = SHIELD
M1O = OLD HOOK-UP ON END 1 W.F. = WIRE FERRULE

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE7-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HCAB
REV 05 Apr 09/21 Page 115
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

AFTER

11
F.R. 47 0294 G
P F.R.
Y
A 64VC
128 80VU 1822VT
128
82VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLK-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLK-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WGAA
REV 05 Apr 09/21 Page 116
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 47 EN3155-014M2018 3138-0294 1M CF22 4000 160 82VU 1822VT 11G EN3155-016M2222 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLN-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HGAA
REV 05 Apr 09/21 Page 117
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005


(4) Task A320-A-31-XX-1583-02001-720A-A (A320-A-31-XX-1583-02ZZZ-720Z-A)
Install the Wiring between Aft Electronics Rack 80VU and FWD Electronics
Rack 90VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Electrical Panel 80VU
120 Work location
Electrical Panel 90VU
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A03R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9000095499995 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 150 TIE (1)
NSA935401-08 150 TIE (1)
NSA935401-13 150 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
3 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 118
A318/A319/A320/A321
SERVICE BULLETIN

4 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
5 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Install the wiring between the aft electronics rack (Electrical Panel 80VU) and the
FWD electronics rack (Electrical Panel 90VU).
Refer to Ref. ESPM 20-33-00
1 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WE and Ref. Fig. HE, supplied in:

1 BUNDLE D9000095499995  
(c) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

150 TIE-CABLE NSA935401-05  


or

150 TIE-CABLE NSA935401-08  


or

150 TIE-CABLE NSA935401-13  


(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 119
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

AFTER

F.R. 70 0304 50 F.R.


281VC A A 64VC
93VU 121 128 80VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLI-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WEAA
REV 05 Apr 09/21 Page 120
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 005

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC-A 50 EN3155-015F2018 3138-0304 1M CF24 15000 600 93VU 281VC-A 70 EN3155-003F2222 (a) A (b) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (a) = BUNDLE D9000095499995 OR
(b) = BUNDLE D9001095400196

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLM-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HEAA
REV 05 Apr 09/21 Page 121
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009


(4) Task A320-A-31-XX-1583-02002-720A-A (A320-A-31-XX-1583-02ZZZ-720Z-A)
Install the Wiring between Aft Electronics Rack 80VU and FWD Electronics
Rack 90VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Electrical Panel 80VU
120 Work location
Electrical Panel 90VU
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9001095400196 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 150 TIE (1)
NSA935401-08 150 TIE (1)
NSA935401-13 150 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
3 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 122
A318/A319/A320/A321
SERVICE BULLETIN

4 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
5 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Install the wiring between the aft electronics rack (Electrical Panel 80VU) and the
FWD electronics rack (Electrical Panel 90VU).
Refer to Ref. ESPM 20-33-00
1 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WE and Ref. Fig. HE, supplied in:

1 BUNDLE D9001095400196  
(c) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

150 TIE-CABLE NSA935401-05  


or

150 TIE-CABLE NSA935401-08  


or

150 TIE-CABLE NSA935401-13  


(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 123
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

AFTER

F.R. 70 0304 50 F.R.


281VC A A 64VC
93VU 121 128 80VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLI-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WEAA
REV 05 Apr 09/21 Page 124
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC-A 50 EN3155-015F2018 3138-0304 1M CF24 15000 600 93VU 281VC-A 70 EN3155-003F2222 (a) A (b) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (a) = BUNDLE D9000095499995 OR
(b) = BUNDLE D9001095400196

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLM-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HEAA
REV 05 Apr 09/21 Page 125
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
(5) Task A320-A-31-XX-1583-03001-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A01R00
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D11311800A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Part kit 311583A04R02


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 126
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311460A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D11311800A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from the position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 127
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400196  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 128
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 129
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 130
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

BEFORE AFTER

1 2
1 2 F.R. 14WW -K3
F.R. 14WW -K3 0469
0241

1 2
1 2 14TD -K19
6TX1 -L17 0241
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P

ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAA
REV 05 Apr 09/21 Page 131
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 14WW 1 2468-0241 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0241 DK10 121VU 6TX1 1 M1N

6 121VU 14TD 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14WW 1 NSA936501TA1003 (b) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(b) = BUNDLE D9001095400196 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE2-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAA
REV 05 Apr 09/21 Page 132
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 133
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 134
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003
(5) Task A320-A-31-XX-1583-03002-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A02R00
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D00411926A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Part kit 311583A05R01


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400296 1 BUNDLE
D9100095450095 1 PLCRDSET

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 135
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD 002046-64 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D00411926A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 136
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400296  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 137
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 138
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 139
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

BEFORE AFTER

1 2
1 2 F.R. 9TU -K18
F.R. 9TU -K18 0469
0115

1 2
1 2 14TD -K19
6TX1 -L17 0115
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE


NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P
ICN-A320-A-31XX1583-A-FAPE3-01RE8-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE8-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAB
REV 05 Apr 09/21 Page 140
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 9TU 1 2468-0115 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0115 DK10 121VU 6TX1 1 M1N

6 121VU 9TU 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14TD 1 NSA936501TA1003 (c) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(c) = BUNDLE D9001095400296 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE5-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAB
REV 05 Apr 09/21 Page 141
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 142
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 143
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004
(5) Task A320-A-31-XX-1583-03022-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A05R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400296 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A07R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D00414089A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 144
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311260A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D00414089A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 145
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400296  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 146
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 147
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 148
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

BEFORE AFTER

1 2
1 2 F.R. 2TW -J18
F.R. 2TW -J18 0469
0114

1 2
1 2 14TD -K19
6TX1 -L17 0114
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE


NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P
ICN-A320-A-31XX1583-A-FAPE3-01YFO-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFO-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAD
REV 05 Apr 09/21 Page 149
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 2TW 1 2468-0114 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0114 DK10 121VU 6TX1 1 M1N

6 121VU 2TW 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14TD 1 NSA936501TA1003 (c) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(c) = BUNDLE D9001095400296 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFK-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAD
REV 05 Apr 09/21 Page 150
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 151
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 152
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006
(5) Task A320-A-31-XX-1583-03023-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A07R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D00414089A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 153
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311260A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D00414089A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from the position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 154
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400196  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 155
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 156
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 157
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

BEFORE AFTER

1 2
1 2 F.R. 14WW -K3
F.R. 14WW -K3 0469
0241

1 2
1 2 14TD -K19
6TX1 -L17 0241
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P

ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAA
REV 05 Apr 09/21 Page 158
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 14WW 1 2468-0241 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0241 DK10 121VU 6TX1 1 M1N

6 121VU 14TD 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14WW 1 NSA936501TA1003 (b) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(b) = BUNDLE D9001095400196 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE2-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAA
REV 05 Apr 09/21 Page 159
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 160
A318/A319/A320/A321
SERVICE BULLETIN

CONF 006

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 161
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007
(5) Task A320-A-31-XX-1583-03024-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A08R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D00411993A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 162
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311272A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D00411993A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from the position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 163
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400196  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 164
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 165
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 166
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

BEFORE AFTER

1 2
1 2 F.R. 14WW -K3
F.R. 14WW -K3 0469
0241

1 2
1 2 14TD -K19
6TX1 -L17 0241
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P

ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAA
REV 05 Apr 09/21 Page 167
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 14WW 1 2468-0241 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0241 DK10 121VU 6TX1 1 M1N

6 121VU 14TD 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14WW 1 NSA936501TA1003 (b) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(b) = BUNDLE D9001095400196 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE2-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAA
REV 05 Apr 09/21 Page 168
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 169
A318/A319/A320/A321
SERVICE BULLETIN

CONF 007

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 170
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008
(5) Task A320-A-31-XX-1583-03025-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A09R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D11311721A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 171
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311461A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D11311721A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from the position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 172
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400196  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 173
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 174
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 175
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

BEFORE AFTER

1 2
1 2 F.R. 14WW -K3
F.R. 14WW -K3 0469
0241

1 2
1 2 14TD -K19
6TX1 -L17 0241
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P

ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE1-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAA
REV 05 Apr 09/21 Page 176
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 14WW 1 2468-0241 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0241 DK10 121VU 6TX1 1 M1N

6 121VU 14TD 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14WW 1 NSA936501TA1003 (b) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(b) = BUNDLE D9001095400196 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01RE2-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAA
REV 05 Apr 09/21 Page 177
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 178
A318/A319/A320/A321
SERVICE BULLETIN

CONF 008

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 179
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009
(5) Task A320-A-31-XX-1583-03026-920A-A (A320-A-31-XX-1583-03ZZZ-920Z-A)
Modify the Equipment and the Wiring in Rear C/B Panel 121VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210 Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
4 NSA931320-050 1 CB
D9001095400196 1 BUNDLE
D9100095450095 1 PLCRDSET

Part kit 311583A09R00


ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
1 D11311721A00 1 PLACARD
2 ASNA2080G04 5 BUTTON

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 50 TIE (1)
NSA935401-08 50 TIE (1)
NSA935401-13 50 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM 06-31-53, Page Block 001
Task 11-00-00-400-002
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 180
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
7 For the installation of placards, refer to Ref. AMM Task 11-00-00-400-002.
(b) Modify the equipment in the rear C/B panel (Electrical Panel 121VU), refer to Ref.
Fig. Modification of the Equipment in Rear C/B Panel 121VU.
1 Remove as shown in view A and B:

FIN 37LM
1 PLACARD D11311461A00 Item (1) Discard
attached with

5 BUTTON RIVET PLASTIC   Item (2) Discard


2 Install as shown in view A and B:

FIN 37LM
1 PLACARD D11311721A00 Item 1
and attach with

5 BUTTON RIVET PLASTIC ASNA2080G04 Item 2


3 Remove from the position 19 as shown in view A thru C:

1 COVER   Item (3) Discard


4 Install at position 19 as shown in view A, B and D:

FIN 14TD
1 CIRCUIT BREAKER NSA931320-050 Item 4
5 Bond the placard identified 14TD as shown in view A, B, D and E, supplied
in:
Refer to Ref. AMM Task 11-00-00-400-002

1 PLACARD SET D9100095450095  


(c) Modify the wiring in the rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WA and Ref. Fig. HA
- Ref. Fig. WF and Ref. Fig. HF, supplied in:
REV 00 Dec 12/19 A320-31-1583
REV 05 Apr 09/21 Page 181
A318/A319/A320/A321
SERVICE BULLETIN

1 BUNDLE D9001095400196  
(d) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

50 TIE-CABLE NSA935401-05  
or

50 TIE-CABLE NSA935401-08  
or

50 TIE-CABLE NSA935401-13  
(e) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 182
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

A
B
Z210

FR12

FR1

(1)
37LM
1 A
K 120VU

(2) x5
2 x5

1
2
3 PD
PWL
4 SP R
LY
5

15
16
17 C D
18
19
20
21
B
121VU

ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHM-A-002-01 SHEET 1/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 183
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

BEFORE

PD
PW L
SP R
LY

AFTER

(3)
14TD
4
C

PD
PW L
SP R
LY

D
PLACARD

14TD

ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RJI-A-001-01 SHEET 2/2


REV 00 Dec 12/19 A320-31-1583
Modification of the Equipment in Rear C/B Panel 121VU
REV 05 Apr 09/21 Page 184
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

BEFORE AFTER

1 2
1 2 F.R. 5TD -J15
F.R. 5TD -J15 0469
0114

1 2
1 2 14TD -K19
6TX1 -L17 0114
F.R.

1 2
6TX1 -L17
F.R.

121VU 121VU

120VU 120VU
212 212

NEW WIRE OLD HOOK-UP NEW HOOK-UP F.R. FOR REFERENCE


NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2468
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK10 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1P
ICN-A320-A-31XX1583-A-FAPE3-01YFN-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFN-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WAAE
REV 05 Apr 09/21 Page 185
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 121VU 5TD 1 2468-0114 DK10 121VU 6TX1 1 M1O

2 121VU 14TD 1 NSA936501TA1003 2468-0114 DK10 121VU 6TX1 1 M1N

6 121VU 5TD 1 NSA936501TA1003 2468-0469 DK10 1000 40 121VU 14TD 1 NSA936501TA1003 (b) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(b) = BUNDLE D9001095400195 M1N = NEW HOOK-UP ON END 1


A = ADDED WIRE
M1O = OLD HOOK-UP ON END 1

Figure ICN-A320-A-31XX1583-A-FAPE3-01YFL-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HAAE
REV 05 Apr 09/21 Page 186
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

AFTER

1 2
F.R. 0291 37 F.R.
5
14TD C/B
PDL PWR SPLY 2212VC A
212 121VU 120VU 212

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE DK22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLJ-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WFAA
REV 05 Apr 09/21 Page 187
A318/A319/A320/A321
SERVICE BULLETIN

CONF 009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 120VU 2212VC 37 EN3155-003F2222 3138-0291 1M DK22 4000 160 121VU 14TD 2 NSA936501TA2205 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01RLL-A-002-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HFAA
REV 05 Apr 09/21 Page 188
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009


(6) Task A320-A-31-XX-1583-03001-720A-A (A320-A-31-XX-1583-03ZZZ-720Z-A)
Install the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Access Panel 212HW, Panel 212JW, Panel 212KW
210
Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A04R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9001095400196 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 140 TIE (1)
NSA935401-08 140 TIE (1)
NSA935401-13 140 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 189
A318/A319/A320/A321
SERVICE BULLETIN

3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Install the wire(s) as shown on this (these) wiring diagram(s) and the related
hook-up chart(s):
Refer to Ref. ESPM 20-33-00
- Ref. Fig. WB and Ref. Fig. HB, supplied in:

1 BUNDLE D9001095400196  
(c) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

140 TIE-CABLE NSA935401-05  


or

140 TIE-CABLE NSA935401-08  


or

140 TIE-CABLE NSA935401-13  


(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 190
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

AFTER

F.R. 37 0293 47 F.R.

2212VC A A 64VC
120VU 212 128 80VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01NMG-A-003-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01NMG-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WBAA
REV 05 Apr 09/21 Page 191
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 006-009

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC-A 47 EN3155-015F2018 3138-0293 1M CF22 14000 560 120VU 2212VC-A 37 EN3155-008M2222 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01NMF-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HBAA
REV 05 Apr 09/21 Page 192
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004


(6) Task A320-A-31-XX-1583-03002-720A-A (A320-A-31-XX-1583-03ZZZ-720Z-A)
Install the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Access Panel 212HW, Panel 212JW, Panel 212KW
210
Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Skills Electrical
Material necessary to do the job
Part kit 311583A05R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9001095400296 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 140 TIE (1)
NSA935401-08 140 TIE (1)
NSA935401-13 140 TIE (1)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 193
A318/A319/A320/A321
SERVICE BULLETIN

3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Install the wire(s) as shown on this (these) wiring diagram(s) and the related
hook-up chart(s):
Refer to Ref. ESPM 20-33-00
- Ref. Fig. WB and Ref. Fig. HB, supplied in:

1 BUNDLE D9001095400296  
(c) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

140 TIE-CABLE NSA935401-05  


or

140 TIE-CABLE NSA935401-08  


or

140 TIE-CABLE NSA935401-13  


(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 194
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

AFTER

F.R. 37 0293 47 F.R.

2212VC A A 64VC
120VU 212 128 80VU

NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF22 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01NMG-A-003-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01NMG-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WBAA
REV 05 Apr 09/21 Page 195
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003 004

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC-A 47 EN3155-015F2018 3138-0293 1M CF22 14000 560 120VU 2212VC-A 37 EN3155-008M2222 (b) A (c) (1)

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

A = ADDED WIRE
(1) = (b) = BUNDLE D9001095400196 OR
(c) = BUNDLE D9001095400296

Figure ICN-A320-A-31XX1583-A-FAPE3-01NMF-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HBAA
REV 05 Apr 09/21 Page 196
A318/A319/A320/A321
SERVICE BULLETIN

CONF ALL
D. PREPARATION FOR TEST
(1) Task A320-A-31-XX-1583-01002-331A-A (A320-A-31-XX-1583-01ZZZ-331Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-38-51-400-001
Procedure
(a) Connect the battery connectors
1 Do the job set-up procedure as specified in the installation of the batteries,
refer to Ref. AMM Task 24-38-51-400-001.
2 Remove the blanking caps from the electrical connectors.
3 Make sure that the electrical connectors are clean and in a correct
condition.
4 Connect the connectors to the battery.
5 Turn the knurled nut a quarter turn.
(b) Remove all the warning notices.
CONF 002 006-008
(2) Task A320-A-31-XX-1583-01001-390A-A (A320-A-31-XX-1583-01ZZZ-390Z-A)
Voltage Check
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-861-002
Procedure
(a) Open, safety/lock and tag this (these) circuit breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


AUDIO MIXING 14WW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 197
A318/A319/A320/A321
SERVICE BULLETIN

PANEL DESIGNATION FIN LOCATION SEE NOTES


(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(b) Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-861-002.
(c) Voltage check
1 Do a voltage check at pin 1 of each circuit breaker that follows to make
sure that there is 28VDC voltage:

PANEL DESIGNATION FIN LOCATION SEE NOTES


AUDIO MIXING 14WW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(d) Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


AUDIO MIXING 14WW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
CONF 003
(2) Task A320-A-31-XX-1583-01002-390A-A (A320-A-31-XX-1583-01ZZZ-390Z-A)
Voltage Check
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-861-002
Procedure
(a) Open, safety/lock and tag this (these) circuit breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


RCDR/ACCLRM 9TU
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 198
A318/A319/A320/A321
SERVICE BULLETIN

(b) Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-861-002.
(c) Voltage check
1 Do a voltage check at pin 1 of each circuit breaker that follows to make
sure that there is 28VDC voltage:

PANEL DESIGNATION FIN LOCATION SEE NOTES


RCDR/ACCLRM 9TU
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(d) Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


RCDR/ACCLRM 9TU
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
CONF 009
(2) Task A320-A-31-XX-1583-01012-390A-A (A320-A-31-XX-1583-01ZZZ-390Z-A)
Voltage Check
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-861-002
Procedure
(a) Open, safety/lock and tag this (these) circuit breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


PDL/PWR/SPLY 14TD (1) (2)
DLS&/DLRB/SPLY 5TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(b) Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-861-002.
(c) Voltage check

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 199
A318/A319/A320/A321
SERVICE BULLETIN

1 Do a voltage check at pin 1 of each circuit breaker that follows to make


sure that there is 28VDC voltage:

PANEL DESIGNATION FIN LOCATION SEE NOTES


PDL/PWR/SPLY 14TD (1) (2)
DLS&/DLRB/SPLY 5TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(d) Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


PDL/PWR/SPLY 14TD (1) (2)
DLS&/DLRB/SPLY 5TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
CONF 004
(2) Task A320-A-31-XX-1583-01013-390A-A (A320-A-31-XX-1583-01ZZZ-390Z-A)
Voltage Check
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-861-002
Procedure
(a) Open, safety/lock and tag this (these) circuit breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


CFDS/CFDIU/SPLY 2TW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(b) Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-861-002.
(c) Voltage check
1 Do a voltage check at pin 1 of each circuit breaker that follows to make
sure that there is 28VDC voltage:

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 200
A318/A319/A320/A321
SERVICE BULLETIN

PANEL DESIGNATION FIN LOCATION SEE NOTES


CFDS/CFDIU/SPLY 2TW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
(d) Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):

PANEL DESIGNATION FIN LOCATION SEE NOTES


CFDS/CFDIU/SPLY 2TW (1) (2)
PDL/PWR/SPLY 14TD (1) (2)
NOTE(S)
(1): For the circuit breaker location, refer to Ref. AMM 24-50-00.
(2): For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-912-001.
CONF ALL
E. TEST
(1) Task A320-A-31-XX-1583-02002-390A-A (A320-A-31-XX-1583-02ZZZ-390Z-A)
Preliminary Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 21-26-00-710-001
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 31-50-00-710-001
AMM
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001
Procedure

NOTE: If the aircraft is operated in actual CAT3 conditions, you must also do the
LAND CAT3 capability test, refer to Ref. AMM Task 22-97-00-710-001.

(a) Do the operational test of the instrument and panel integral lighting, refer to Ref.
AMM Task 33-13-00-710-001.
(b) Do the operational test of the lights, refer to Ref. AMM Task 33-14-00-710-001.
(c) Do the operational check of the avionics equipment ventilation-system through
the Multipurpose Control & Display Unit (MCDU), refer to Ref. AMM Task 21-26-
00-710-001.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 201
A318/A319/A320/A321
SERVICE BULLETIN

(d) Do the operational test of the Automatic Flight System (AFS), refer to Ref. AMM
Task 22-96-00-710-001.
(e) Do the operational test of the Electronic Instrument System (EIS), refer to Ref.
AMM Task 31-60-00-710-001.
(f) Do the operational test of the Electronic Centralized Aircraft Monitoring (ECAM)
control panel, refer to Ref. AMM Task 31-50-00-710-004.
(g) Do the ground scanning of the central warning system, refer to Ref. AMM Task
31-50-00-710-001.
CONF 001 002 005-009
(2) Task A320-A-31-XX-1583-03001-390A-A (A320-A-31-XX-1583-03ZZZ-390Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 21-63-34-400-001
Task 27-94-34-400-001
AMM Task 31-38-00-740-001
Task 32-31-71-400-001
Task 46-21-34-400-001
Procedure
(a) This Service Bulletin requires the accomplishment of Tests given in other topics
which are referenced in the table below:

Task Tests
The test procedures of LGCIU-1, zone Do the test procedure as specified after the
controller and SEC-3 are performed in the installation of LGCIU-1 (FIN 5GA1), refer to
Line Replaceable Unit (LRU) installation Ref. AMM Task 32-31-71-400-001.
procedures through Ref. Task A320-A-31-XX- Do the test procedure as specified after the
1583-02ZZZ-740Z-A. installation of the zone controller (FIN 8HK)
(If installed), refer to Ref. AMM Task 21-63-
34-400-001.
Do the test procedure as specified after the
installation of SEC-3 (FIN 1CE3), refer to Ref.
AMM Task 27-94-34-400-001.
(b) Do the test after the installation of the ATSU (FIN 1TX1), refer to Ref. AMM Task
46-21-34-400-001.
(c) Do the Built-In Test Equipment (BITE) test of the DLRB, refer to Ref. AMM Task 31-
38-00-740-001.
CONF 003 004
(2) Task A320-A-31-XX-1583-03002-390A-A (A320-A-31-XX-1583-03ZZZ-390Z-A)
Test

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 202
A318/A319/A320/A321
SERVICE BULLETIN

Job Set-Up Information


Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 28-22-00-710-002
AMM
Task 46-21-34-400-001
Procedure
(a) Do the test after the Installation of the ATSU, refer to Ref. AMM Task 46-21-34-
400-001
(b) Do the operational test of the APU fuel-pump system, refer to Ref. AMM Task 28-
22-00-710-002.
CONF ALL
F. CLOSE-UP
CONF 002-004 006-009
(1) Task A320-A-31-XX-1583-01001-740A-A (A320-A-31-XX-1583-01ZZZ-740Z-A)
Install/Close Items Removed/Opened for access to Rear Panel 120VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Top Coat Polyurethane -
04JMD9
Decorative Furnishing
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM 06-41-53, Page Block 001
Task 20-21-11-911-001
Task 25-13-41-400-002
CML CONSUMABLE MATERIAL LIST (CML)
51-42-00
SRM
51-75-12
Procedure
(a) Standard Practices

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 203
A318/A319/A320/A321
SERVICE BULLETIN

1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 For the specification of Material application codes given in this Service
Bulletin, refer to the Ref. CML.
6 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
7 To torque tighten the standard threaded fasteners, refer to Ref. AMM Task
20-21-11-911-001.
(b) Install the right aft console (Electrical Panel 702VU) in the cockpit in accordance
with Ref. SRM 51-42-00, refer to Ref. AMM Task 20-21-11-911-001 and Ref. Fig.
Removal/Installation of Right Aft Console 702VU from/in the Cockpit (For Access).
1 Install as shown in view A:

1 STRUCTURE   Item (54) Retained


and attach with

6 SCREW   Item (53) Retained

6 WASHER   Item (52) Retained


(c) Install the stowage box to the right aft console, in the cockpit in accordance
with Ref. SRM 51-42-00, refer to Ref. AMM Task 20-21-11-911-001 and Ref. Fig.
Installation of the Stowage Box in the Right Aft Console, in the Cockpit.
1 Install as shown in view A and C:

1 BOX ASSY-STOWAGE   Item (51) Retained


and attach with

4 SCREW   Item (50) Retained

2 SCREW   Item (48) Retained

2 WASHER   Item (49) Retained


2 Install as shown in view A and B:

1 MODULE ASSY 702VU   Item (43) Retained


and attach with

4 SCREW   Item (48) Retained

1 SCREW   Item (47) Retained

2 SCREW   Item (44) Retained

4 WASHER   Item (49) Retained

2 WASHER   Item (45) Retained

1 WASHER   Item (46) Retained

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 204
A318/A319/A320/A321
SERVICE BULLETIN

3 Renew the protective finish on the fasteners, with:

  Top Coat Polyurethane - 04JMD9  


Decorative Furnishing
(d) Install the panel in accordance with Ref. SRM 51-42-00, refer to Ref. AMM Task
20-21-11-911-001 and Ref. Fig. Removal/Installation of the Access Panel from/in
the Cockpit (For Access).
1 Install as shown in view A and B:

1 PANEL-RH LATERAL   Item (40) Retained


and attach with

2 SCREW   Item (41) Retained

1 SCREW   Item (42) Retained


(e) Install the sidewall panels (Panel 212HW, Panel 212JW and Panel 212KW) in the
cockpit, refer to Ref. AMM Task 25-13-41-400-002.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 205
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

(52)
(53)

(53)

(54) (52)

(53)

(52)
(53)

(52)

A
702VU
ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of Right Aft Console A320-31-1583
REV 05 Apr 09/21 702VU from/in the Cockpit (For Access) Page 206
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

C
(46) 01
(47) 01
(48) 01
A
01 (44) 702VU
(45) 01

(49) 01

(43)

NOTE:
01 RENEW THE PROTECTIVE FINISH WITH MATERIAL No 04JMD9
ICN-A320-A-31XX1583-A-FAPE3-01RGE-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RGE-A-001-01 SHEET 1/2


REV 00 Dec 12/19 Installation of the Stowage Box in A320-31-1583
REV 05 Apr 09/21 the Right Aft Console, in the Cockpit Page 207
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

01 (50)

(50) 01

(51)

01 (48)

01 (49)

NOTE:
01 RENEW THE PROTECTIVE FINISH WITH MATERIAL No 04JMD9
ICN-A320-A-31XX1583-A-FAPE3-01RH7-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH7-A-001-01 SHEET 2/2


REV 00 Dec 12/19 Installation of the Stowage Box in A320-31-1583
REV 05 Apr 09/21 the Right Aft Console, in the Cockpit Page 208
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002-004 006-009

A
Z210

FR12

FR1
B

(41)

(40)

(42)

(41)
ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of the Access A320-31-1583
REV 05 Apr 09/21 Panel from/in the Cockpit (For Access) Page 209
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001 002 005-009


(2) Task A320-A-31-XX-1583-02001-740A-A (A320-A-31-XX-1583-02ZZZ-740Z-A)
Install/Close for Access to FWD Electronics Rack 90VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 21-63-34-400-001
AMM Task 27-94-34-400-001
Task 32-31-71-400-001
Procedure
(a) Install the shelf (Electrical Panel 93VU).
1 Install the shelf (Electrical Panel 93VU) on the aircraft.
2 Do the electrical bonding on the shelf attachment.
3 Attach the shelf (Electrical Panel 93VU) and connect the bonding braid with
the hardware retained at removal.
4 Connect the related connectors.
5 Install retained LGCIU-1 (FIN 5GA1) on the shelf (Electrical Panel 93VU),
refer to Ref. AMM Task 32-31-71-400-001.
6 Install the retained zone controller (FIN 8HK) (if removed) on the shelf
(Electrical Panel 93VU), refer to Ref. AMM Task 21-63-34-400-001.
7 Install retained SEC-3 (FIN 1CE3) on the shelf (Electrical Panel 93VU), refer
to Ref. AMM Task 27-94-34-400-001.
CONF ALL
(3) Task A320-A-31-XX-1583-03001-740A-A (A320-A-31-XX-1583-03ZZZ-740Z-A)
Close-up
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 25-54-11-400-001

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 210
A318/A319/A320/A321
SERVICE BULLETIN

Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the partition panels (Panel 131CW, Panel 131DW and Panel 132EW) in the
FWD cargo compartment, at Frame 24A, refer to Ref. AMM Task 25-54-11-400-
001.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-31-XX-1583-01001-90AA-A (A320-A-31-XX-1583-01ZZZ-90AZ-A)
Administrative

Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 211
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003


Task set A320-A-31-XX-1583-02000-93AA-A (A320-A-31-XX-1583-02ZZZ-93AZ-A)
Additional work for Aircraft Modified by the original issue of this Service Bulletin

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL


WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.

A. TASK SET ASSOCIATED INFORMATION


Task Manpower
CONF 002
TOTAL MAN-HOURS 7.50 h
CONF 003
TOTAL MAN-HOURS 7.50 h
CONF 002
ELAPSED TIME (HOURS) 7.50 h
CONF 003
ELAPSED TIME (HOURS) 7.50 h
CONF 002 003
B. PREPARATION
(1) Task A320-A-31-XX-1583-06001-540A-A (A320-A-31-XX-1583-06ZZZ-540Z-A)
Job Set-up

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 212
A318/A319/A320/A321
SERVICE BULLETIN

Job Set-Up Information


Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 12-34-24-869-002
AMM
Task 25-54-11-000-001
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.
(b) Remove the partition panels (Panel 131CW, Panel 131DW and Panel 132EW)
from the FWD cargo compartment, at Frame 24A for access, refer to Ref. AMM
Task 25-54-11-000-001.
(2) Task A320-A-31-XX-1583-08001-540A-A (A320-A-31-XX-1583-08ZZZ-540Z-A)
Aircraft/System Configuration
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-38-51-000-001
Procedure
(a) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(b) Put the warning notices in position on the external power receptacle to tell
persons not to connect an external power source.
(c) Make sure that the EMER EXIT LT pushbutton switch on the overhead CTL & IND
panel (Electrical Panel 25VU) is set to the OFF position.
(d) In the cockpit, on the ELEC panel (Electrical Panel 35VU), release the BAT
pushbutton switches.
(e) Put a warning notice in position on the ELEC panel (Electrical Panel 35VU) to tell
persons not to operate the batteries.
(f) Put a warning notice in position on the refuel/defuel control panel (Electrical
Panel 800VU) to tell persons not to operate the NORMAL BATTERY switch.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 213
A318/A319/A320/A321
SERVICE BULLETIN

(g) Put a warning notice in position in the cockpit to tell persons not to start the
APU.
(h) Put a warning notice in position in the cockpit to tell persons not to start ENG 1
and ENG 2.
(i) Disconnect the battery connectors:
1 Do the job set-up procedure as specified in the removal of the batteries,
refer to Ref. AMM Task 24-38-51-000-001.
2 Turn the knurled nut a quarter turn.
3 Disconnect the connectors.
4 Put the blanking caps on the disconnected electrical connectors.
(3) Task A320-A-31-XX-1583-07001-540A-A (A320-A-31-XX-1583-07ZZZ-540Z-A)
Remove/Open for Access to Rear Panel 120VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM 06-41-53, Page Block 001
Task 20-21-15-912-001
Task 25-13-41-000-002
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
5 Tag all the parts you must remove and retain to make the subsequent
installation easier.
6 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
7 To torque tighten the electrical component fasteners, refer to Ref. AMM
Task 20-21-15-912-001.
(b) Remove the sidewall panels (Panel 212HW, Panel 212JW and Panel 212KW) from
the cockpit for access, refer to Ref. AMM Task 25-13-41-000-002.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 214
A318/A319/A320/A321
SERVICE BULLETIN

(c) Remove the panel from the cockpit in accordance with Ref. SRM 51-42-00 and
refer to Ref. Fig. Removal/Installation of the Access Panel from/in the Cockpit (For
Access).
1 Remove as shown in view A and B:

1 PANEL-RH LATERAL   Item (40) Retain


attached with

2 SCREW   Item (41) Retain

1 SCREW   Item (42) Retain


(d) Remove the stowage box from the right aft console, in the cockpit in accordance
with Ref. SRM 51-42-00 and refer to Ref. Fig. Removal of the Stowage Box from
the Right Aft Console, in the Cockpit (For Access).
1 Remove as shown in view A and B:

1 MODULE ASSY 702VU   Item (43) Retain


attached with

4 SCREW   Item (48) Retain

1 SCREW   Item (47) Retain

2 SCREW   Item (44) Retain

4 WASHER   Item (49) Retain

2 WASHER   Item (45) Retain

1 WASHER   Item (46) Retain


2 Remove as shown in view A and C:

1 BOX ASSY-STOWAGE   Item (51) Retain


attached with

4 SCREW   Item (50) Retain

2 SCREW   Item (48) Retain

2 WASHER   Item (49) Retain


(e) Remove the right aft console (Electrical Panel 702VU) from the cockpit in
accordance with Ref. SRM 51-42-00 and refer to Ref. Fig. Removal/Installation of
Right Aft Console 702VU from/in the Cockpit (For Access).
1 Remove as shown in view A:

1 STRUCTURE   Item (54) Retain


attached with

6 SCREW   Item (53) Retain

6 WASHER   Item (52) Retain

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 215
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

A
Z210

FR12

FR1
B

(41)

(40)

(42)

(41)
ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of the Access A320-31-1583
REV 05 Apr 09/21 Panel from/in the Cockpit (For Access) Page 216
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

C
(46)
(47)
(48)
A
(44) 702VU
(45)

(49)

(43)

ICN-A320-A-31XX1583-A-FAPE3-01RH9-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH9-A-001-01 SHEET 1/2


REV 00 Dec 12/19 Removal of the Stowage Box from the Right A320-31-1583
REV 05 Apr 09/21 Aft Console, in the Cockpit (For Access) Page 217
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

(50)

(50)

(51)

(48)

(49)

ICN-A320-A-31XX1583-A-FAPE3-01RHA-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHA-A-001-01 SHEET 2/2


REV 00 Dec 12/19 Removal of the Stowage Box from the Right A320-31-1583
REV 05 Apr 09/21 Aft Console, in the Cockpit (For Access) Page 218
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

(52)
(53)

(53)

(54) (52)

(53)

(52)
(53)

(52)

A
702VU
ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of Right Aft Console A320-31-1583
REV 05 Apr 09/21 702VU from/in the Cockpit (For Access) Page 219
A318/A319/A320/A321
SERVICE BULLETIN

C. PROCEDURE
(1) Task A320-A-31-XX-1583-07001-920A-A (A320-A-31-XX-1583-07ZZZ-920Z-A)
Modify the Wiring between Rear C/B Panel 121VU and Aft Electronics Rack
80VU
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


Access Panel 131CW, Panel 131DW, Panel 131EW
120
Work location Electrical Panel 80VU
Access Panel 212HW, Panel 212JW, Panel 212KW
210
Work location Electrical Panel 121VU
Manpower/Resources/Skills

Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Material necessary to do the job
Part kit 311583A10R00
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9001095405095 1 BUNDLE

Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NSA935401-05 180 TIE
NSA935401-08 180 TIE
NSA935401-13 180 TIE
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-41-53, Page Block 001
20-33-00
20-33-44
ESPM 20-52-21
20-54-50
20-56-51
Procedure
(a) Standard Practices
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
3 For the cable tie application and tooling, refer to Ref. ESPM 20-33-44 and
Ref. ESPM 20-56-51.
4 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 220
A318/A319/A320/A321
SERVICE BULLETIN

5 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
6 To install new wires, cut them to the necessary length, attach the terminals
and connect them.
(b) Modify the wiring in the aft electronics rack (Electrical Panel 80VU) and in the
rear C/B panel (Electrical Panel 121VU).
Refer to Ref. ESPM 20-33-00
1 Remove the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WH and Ref. Fig. HH.
2 Install the wire(s) as shown on this (these) wiring diagram(s) and the
related hook-up chart(s):
- Ref. Fig. WH and Ref. Fig. HH, supplied in:

1 BUNDLE D9001095405095  
(c) Attach the wire(s) with:
Refer to Ref. ESPM 20-33-44 and Ref. ESPM 20-56-51

180 TIE-CABLE NSA935401-05  


or

180 TIE-CABLE NSA935401-08  


or

180 TIE-CABLE NSA935401-13  


(d) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 221
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

BEFORE

11
F.R. 37 0293 47 0294 G
P F.R.
Y
2212VC A A 64VC
120VU 212 128 80VU 1822VT
128
82VU

AFTER

11
F.R. 37 0293 CF22 47 0294 CF22 G
P F.R.
Y
2212VC A A 64VC
120VU 212 128 80VU 1822VT
128
82VU

DELETED WIRE NEW WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3138
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M

ICN-A320-A-31XX1583-A-FAPE3-01Z74-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01Z74-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
WHAA
REV 05 Apr 09/21 Page 222
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N

1 80VU 64VC 47 3138-0294 1M CF24 82VU 1822VT 11G D

2 80VU 64VC-A 47 3138-0293 1M CF24 120VU 2212VC-A 37 D

6 80VU 64VC 47 EN3155-014M2018 3138-0294 1M CF22 4000 160 82VU 1822VT 11G EN3155-016M2222 (d) A

7 80VU 64VC-A 47 EN3155-015F2018 3138-0293 1M CF22 14000 560 120VU 2212VC-A 37 EN3155-008M2222 (d) A

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

(d) = BUNDLE D9001095405095


A = ADDED WIRE
D = DELETED WIRE

Figure ICN-A320-A-31XX1583-A-FAPE3-01Z73-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
HHAA
REV 05 Apr 09/21 Page 223
A318/A319/A320/A321
SERVICE BULLETIN

D. PREPARATION FOR TEST


(1) Task A320-A-31-XX-1583-02001-331A-A (A320-A-31-XX-1583-02ZZZ-331Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 24-38-51-400-001
AMM
Task 24-41-00-861-002
Procedure
(a) Connect the battery connectors
1 Do the job set-up procedure as specified in the installation of the batteries,
refer to Ref. AMM Task 24-38-51-400-001.
2 Remove the blanking caps from the electrical connectors.
3 Make sure that the electrical connectors are clean and in a correct
condition.
4 Connect the connectors to the battery.
5 Turn the knurled nut a quarter turn.
(b) Remove all the warning notices.
(c) Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-861-002.
E. TEST
(1) Task A320-A-31-XX-1583-04001-390A-A (A320-A-31-XX-1583-04ZZZ-390Z-A)
Preliminary Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 21-26-00-710-001
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 31-50-00-710-001
AMM
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 224
A318/A319/A320/A321
SERVICE BULLETIN

Procedure

NOTE: If the aircraft is operated in actual CAT3 conditions, you must also do the
LAND CAT3 capability test, refer to Ref. AMM Task 22-97-00-710-001.

(a) Do the operational test of the instrument and panel integral lighting, refer to Ref.
AMM Task 33-13-00-710-001.
(b) Do the operational test of the lights, refer to Ref. AMM Task 33-14-00-710-001.
(c) Do the operational check of the avionics equipment ventilation-system through
the MCDU, refer to Ref. AMM Task 21-26-00-710-001.
(d) Do the operational test of the AFS, refer to Ref. AMM Task 22-96-00-710-001.
(e) Do the operational test of the EIS, refer to Ref. AMM Task 31-60-00-710-001.
(f) Do the operational test of the ECAM control panel, refer to Ref. AMM Task 31-50-
00-710-004.
(g) Do the ground scanning of the central warning system, refer to Ref. AMM Task
31-50-00-710-001.
CONF 002
(2) Task A320-A-31-XX-1583-05001-390A-A (A320-A-31-XX-1583-05ZZZ-390Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 31-38-00-740-001
Procedure
(a) Do the Built-In Test Equipment (BITE) test of the DLRB, refer to Ref. AMM Task 31-
38-00-740-001.
CONF 003
(2) Task A320-A-31-XX-1583-05003-390A-A (A320-A-31-XX-1583-05ZZZ-390Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 28-22-00-710-002
Procedure

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 225
A318/A319/A320/A321
SERVICE BULLETIN

(a) Do the operational test of the APU fuel-pump system, refer to Ref. AMM Task 28-
22-00-710-002.
CONF 002 003
F. CLOSE-UP
(1) Task A320-A-31-XX-1583-04001-740A-A (A320-A-31-XX-1583-04ZZZ-740Z-A)
Install/Close Items Removed/Opened for access to Rear Panel 120VU
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job

Consumables
ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES
Top Coat Polyurethane -
04JMD9
Decorative Furnishing
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
06-31-53, Page Block 001
AMM 06-41-53, Page Block 001
Task 20-21-11-911-001
Task 25-13-41-400-002
CML CONSUMABLE MATERIAL LIST (CML)
51-42-00
SRM
51-75-12
Procedure
(a) Standard Practices
1 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
2 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
3 For the identification of access panels, refer to Ref. AMM 06-41-53, Page
Block 001.
4 Renew the protective finish in accordance with Ref. SRM 51-75-12.
5 For the specification of Material application codes given in this Service
Bulletin, refer to the Ref. CML.
6 Remove and install fasteners in accordance with Ref. SRM 51-42-00.
7 To torque tighten the standard threaded fasteners, refer to Ref. AMM Task
20-21-11-911-001.
(b) Install the right aft console (Electrical Panel 702VU) in the cockpit in accordance
with Ref. SRM 51-42-00, refer to Ref. AMM Task 20-21-11-911-001 and Ref. Fig.
Removal/Installation of Right Aft Console 702VU from/in the Cockpit (For Access).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 226
A318/A319/A320/A321
SERVICE BULLETIN

1 Install as shown in view A:

1 STRUCTURE   Item (54) Retained


and attach with

6 SCREW   Item (53) Retained

6 WASHER   Item (52) Retained


(c) Install the stowage box to the right aft console, in the cockpit in accordance
with Ref. SRM 51-42-00, refer to Ref. AMM Task 20-21-11-911-001 and Ref. Fig.
Installation of the Stowage Box in the Right Aft Console, in the Cockpit.
1 Install as shown in view A and C:

1 BOX ASSY-STOWAGE   Item (51) Retained


and attach with

4 SCREW   Item (50) Retained

2 SCREW   Item (48) Retained

2 WASHER   Item (49) Retained


2 Install as shown in view A and B:

1 MODULE ASSY 702VU   Item (43) Retained


and attach with

4 SCREW   Item (48) Retained

1 SCREW   Item (47) Retained

2 SCREW   Item (44) Retained

4 WASHER   Item (49) Retained

2 WASHER   Item (45) Retained

1 WASHER   Item (46) Retained


3 Renew the protective finish on the fasteners, with:

  Top Coat Polyurethane - 04JMD9  


Decorative Furnishing
(d) Install the panel in accordance with Ref. SRM 51-42-00, refer to Ref. AMM Task
20-21-11-911-001 and Ref. Fig. Removal/Installation of the Access Panel from/in
the Cockpit (For Access).
1 Install as shown in view A and B:

1 PANEL-RH LATERAL   Item (40) Retained


and attach with

2 SCREW   Item (41) Retained

1 SCREW   Item (42) Retained


(e) Install the sidewall panels (Panel 212HW, Panel 212JW and Panel 212KW) in the
cockpit, refer to Ref. AMM Task 25-13-41-400-002.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 227
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

(52)
(53)

(53)

(54) (52)

(53)

(52)
(53)

(52)

A
702VU
ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH8-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of Right Aft Console A320-31-1583
REV 05 Apr 09/21 702VU from/in the Cockpit (For Access) Page 228
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

C
(46) 01
(47) 01
(48) 01
A
01 (44) 702VU
(45) 01

(49) 01

(43)

NOTE:
01 RENEW THE PROTECTIVE FINISH WITH MATERIAL No 04JMD9
ICN-A320-A-31XX1583-A-FAPE3-01RGE-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RGE-A-001-01 SHEET 1/2


REV 00 Dec 12/19 Installation of the Stowage Box in A320-31-1583
REV 05 Apr 09/21 the Right Aft Console, in the Cockpit Page 229
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

01 (50)

(50) 01

(51)

01 (48)

01 (49)

NOTE:
01 RENEW THE PROTECTIVE FINISH WITH MATERIAL No 04JMD9
ICN-A320-A-31XX1583-A-FAPE3-01RH7-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RH7-A-001-01 SHEET 2/2


REV 00 Dec 12/19 Installation of the Stowage Box in A320-31-1583
REV 05 Apr 09/21 the Right Aft Console, in the Cockpit Page 230
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002 003

A
Z210

FR12

FR1
B

(41)

(40)

(42)

(41)
ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01RHB-A-001-01 SHEET 1/1


REV 00 Dec 12/19 Removal/Installation of the Access A320-31-1583
REV 05 Apr 09/21 Panel from/in the Cockpit (For Access) Page 231
A318/A319/A320/A321
SERVICE BULLETIN

(2) Task A320-A-31-XX-1583-05001-740A-A (A320-A-31-XX-1583-05ZZZ-740Z-A)


Close-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 25-54-11-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the partition panels (Panel 131CW, Panel 131DW and Panel 132EW) in the
FWD cargo compartment, at Frame 24A, refer to Ref. AMM Task 25-54-11-400-
001.
(c) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-31-XX-1583-02001-90AA-A (A320-A-31-XX-1583-02ZZZ-90AZ-A)
Administrative

Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 232
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
CONF ALL
APPENDIX
A. CONFIGURATION DEFINITION TABLE
Configuration Definition Table
For further information concerning the Configuration Definition, refer to the next page(s).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 233
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
CONF ALL

MODIFICATIONS / SERVICE BULLETIN

WIRING
PROVISION
WIRING
INSTALL
INSTALL PROVISION
PROVISION INSTALL DLRB
PDL POWER REMOVE FOMAX FANS SYSTEM
THE BETWEEN ARRANGEMENT FOR ATSU. & DLS DLBR
SUPPLY 183VC PROVISION PROVISIONS PRE P/N OF PLACARD 37LM
OF ADDED CB 14TD INSTALL (CB 5TD) REMOVED
(CB 14TD) AND INSTALLED INSTALLED
183VC, 3TD
CONNECT
WIRING
ATSU / DLRB
ATSU
TO 183VC

D11311260A00

D11311272A00

D11311461A00

D11311460A00

D11311800A00

D00414253A00

002046-64
MOD 14WW 9TU AND 2TW AND 5TD AND MOD MOD MOD MOD MOD MOD
33441P8185 AND 6TX1 6TX1 6TX1 6TX1 26878P4500 27948P5771 25293P4151 163660P18410 153481P18093 28552P6198

CONF 001 X X X X
CONF 002 X X X X X
CONF 003 X X X
CONF 004 X X X X X X X
CONF 005 X X X X
CONF 006 X X X X X
CONF 007 X X X X X
CONF 008 X X X X X
CONF 009 X X X X X

NOTE:
"X" IS USED FOR MODIFICATIONS EMBODIED BEFORE ACCOMPLISHMENT OF THIS SERVICE BULLETIN. ICN-A320-A-31XX1583-A-FAPE3-01YGM-A-003-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01YGM-A-003-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
Configuration Definition Table
REV 05 Apr 09/21 Page 234
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
B. RETROFITTED MODIFICATION
Retrofitted Modification
For the retrofitted modifications after accomplishment of this Service Bulletin, refer to the
table below.

MOD CONF CONF CONF CONF CONF CONF CONF CONF CONF
001 002 003 004 005 006 007 008 009
33443P8153 X X X X X X X
163660P18410 X X X X X X X
36208P8990 X X
38958P11023 X

NOTE: "X" is used for the retrofitted modifications after accomplishment of this Service
Bulletin.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 235
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
C. MANPOWER GANTT CHART
Manpower Gantt Chart
For an explanation of the man-hours and elapsed time, refer to the next page(s).

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 236
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
CONF 002 006-009

01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-31-1583
02

STEPS MH PER ET/S

GET ACCESS 4.00 2 2.00

MODIFY THE EQUIPMENT 2.00 1 2.00


AND THE WIRING IN SHELF
93VU

INSTALL THE EQUIPMENT 4.00 1 4.00


AND THE WIRING IN AFT
ELECTRONICS RACK 80VU

INSTALL THE WIRING 1.00 1 1.00


BETWEEN AFT ELECTRONICS
RACK 80VU AND FWD
ELECTRONICS RACK 90VU
MODIFY THE EQUIPMENT 2.00 1 2.00
AND THE WIRING IN
REAR C/B PANEL 121VU

INSTALL THE WIRING BETWEEN 1.00 1 1.00


REAR C/B PANEL 121VU AND
AFT ELECTRONICS RACK 80VU

TEST 2.00 1 2.00

CLOSE-UP 4.00 2 2.00

0 2 4 6 8 10
SB ELAPSED TIME
TOTAL MANHOURS 20.00 (HOURS)
SB ELAPSED TIME 11.00

NOTE:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-31XX1583-A-FAPE3-01ROT-A-001-01

Figure ICN-A320-A-31XX1583-A-FAPE3-01ROT-A-001-01 SHEET 1/1


REV 00 Dec 12/19 A320-31-1583
Manpower Gantt Chart
REV 05 Apr 09/21 Page 237
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
CONF ALL
D. GLOSSARY
Glossary

ACRONYM FULL FORM


ARINC Aeronautical Radio Incorporated
ATSU Air Traffic Service Unit
C/B Circuit Breaker
FWD Forward
LGCIU Landing Gear Control and Interface Unit
PDL Portable Data Loader
SEC Spoiler Elevator Computer

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 238
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
E. REPORTING SHEET

TITLE: INDICATING/RECORDING SYSTEMS - UP AND DOWN DATA LOADING


SYSTEM - INSTALL ARINC 615A PDL CONNECTOR FOR ATSU

MODIFICATION No.: 163660P18410 33443P8153 36208P8990 38958P11023


(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus, Question 2 "What are


the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 239
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
F. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.

Quality rating of this SB 4 3 2 1


Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y/N

NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score

If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.

Planning Material Instructions


X Applicability X Tooling X Preparation
X Reason X List of Materials X Mod/Inspection
Operator Supplied
X Manpower X Kit content X Test
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support

Comments :

Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

REV 00 Dec 12/19 A320-31-1583


REV 05 Apr 09/21 Page 240

You might also like