Professional Documents
Culture Documents
FK 4142
FK 4142
42(11)GB
DN 80-600, PN 10-40, ANSI Class 150, 300 10.00
Replaces Fk41.42(10)GB 1.99
Primary characteristics
NAF-Torex butterfly valve is available with either metal-
to-metal or soft seats. Due to its unique design, it closes
as tightly as a globe valve. It can be used both as a
control valve and as a shut-off valve. It is supplied as
standard in stainless steel as wafer type for pressure
ratings PN 10 - 40 and ANSI 150 - 300 and as lug type
for ANSI 150. Sizes DN 80 - 600.
The valves are also available in other materials e.g.
Carbon steel, Titanium and NACE-material and in Fire-
safe design. Contact NAF for more information.
The valve has:
double offset action which enables the valve closure
to be adjusted externally and ensures good tightness
in the closed position.
small offset and thus low operating torque in all
control positions, so that low-torque actuators can
be used.
a special disc profile (segment of a toroid) - a patented Technical specification
principle which eliminates abrasive sliding action Size range: DN 80—600
when the disc is opening and closing, thus ensuring Pressure ratings: PN 10 - 40
a longer service life. ANSI Class 150 and 300
a large mean value of seating angle, so that the disc Max. differential pressure:
closes without tending to stick in the closed position. valve closed DN 80—600 25 bar
at 70° open valve DN 80 8 bar
metaloplast bearings. For temperature above 250°C
DN 100 13 bar
hard chromium stem, direct mounted in the body (Limitation depending DN 125 11 bar
a one-piece valve body of stainless steel. of high velocity with DN 150 6,5 bar
big dynamic torque DN 200 4,5 bar
a metallic or soft seat ring. Soft seats of three
at this differential DN 250 3 bar
different materials are available. pressure when valve DN 300 2,7 bar
the NAF standard for mounting the actuator, which is open 70°) DN 350 1,8 bar
simplifies installation and results in a compact DN 400 2 bar
valve/actuator unit. DN 500 1,9 bar
DN 600 1,8 bar
See also page 3
Applications
NAF-Torex can be used both as a control valve and as a Face-to-face lengths: Wafer type
shut-off valve, in a wide variety of applications and in PN 10-25: EN 558-1, serie 20
ANSI Class 150: API standard
different operating modes.
609 Class 150
The valve represents a concrete result of our product
PN 40: EN 558-1, serie 16
philosophy which is focused on functionality, high quality
ANSI Class 300: API standard
and low life cycle costs, and is based on concentrating our
609 Class 3001)
range to a limited number of valve types, but all of them
Lug type
suitable for a wide variety of applications. ANSI Class 150: API Standard
The excellent characteristics of NAF-Torex are particular- 609 Clas 150
ly beneficial in arduous control applications, in which
difficult media and demanding pressure conditions make Installation method: Wafer type and Lug type
body
severe demands on the design, materials and performance.
Temperature range: Up to 350°C
(see product code)
Test pressure: 1.5 x PN with valve open
1.1 x Max. differential
pressure with valve closed
Sealing class: Soft seats:
ISO 5208-2, Rate A
DIN 3230 BN, Leckrate 1
Metal seats:
IEC 534-4, Class V
1) Wafer type ANSI Class 300 also available with face-to-face
according to EN 558-1, serie 16. (PN 40).
1
Materials
4 1 Stem, SS 2324,
driven hardchromiumplated
5 1 Stem, SS 2324,
lower hardchromiunplated
2
NAF-Torex butterfly valves
Kv at opening angle at
DN
10° 20° 30° 40° 50° 60° 70° 80° 90°
80 22 - 29 50 38 60 42 67 45 75
100 30 - 38 70 50 85 55 100 65 110
125 50 - 65 95 85 115 95 135 110 150
150 80 - 105 140 130 170 150 200 170 230
200 160 - 205 300 270 350 300 400 350 470
250 280 - 370 500 480 600 540 720 650 850
300 450 - 580 750 750 980 850 1100 960 1250
350 660 - 860 1100 1120 1400 1240 1620 1460 1900
400 940 - 1220 1600 1600 2000 1820 2370 2070 2700
500 1700 - 2200 2800 2800 3500 3140 4090 3610 4700
600 2700 - 3530 4600 4460 5800 5150 6700 5920 7700
Soft = Soft seat ring (EPDM, FPM)
Hard = Metal seat ring (Inconel 718) and PTFE seat ring
Operating torque
The above table specifies the torques necessary for
closing the valve to the specified tightness. To achieve torque is decisive for the actuator selection.
the specified tightness with a metal or a PTFE seat ring, In doubts, consult NAF concerning the torque required
the minimum design torque is that corresponding to a for actuator selection.
differential pressure of 10 bar.At flow through the
valve the disc is being affected by dynamic torque Sizing of control valves
which tries to close the valve. At liquid flow and high We have a Window based valve calculation program
velocities this may be decisive for selection of actuator which is advanced but very easy to use. This program
size.In general, for this valve, is valid that water velocities can be ordered through your NAF representative.
below 8 m/s in the pipe line at fully open valve do not The program is based on calculation formula according
give a dynamic torque higher than the closing torques to the Standards IEC 534, ISA 575.01 and VDMA 24422.
according to the above table.
This means that it is utmost rare that the dynamic
3
Dimensions and mass
ØD
T
H
ØA
ØB
ØR
ØS
Valve stem
DN A B D E F G H K L M N P S Mass, kg
Wafer Lug Wafer Lug
All dimensions in mm
1) ANSI Class 150 size 14" has L = 92 mm
4
NAF-Torex butterfly valves
DN A B D E F G H K L M N P Mass, kg
PN ANSI PN ANSI PN ANSI PN ANSI PN ANSI PN ANSI PN ANSI
Actuators
NAF-Torex is available with hand levers or
with pneumatic or electric actuators and
accessories.
Use the following tables for selecting the
hand levers and standard pneumatic
actuators.
5
The below stated dP apply for clean media type water.
NAF-Torex valves with pneumatic actuators For other media contact NAF, see also page 3.
Valve Max. dp bar at supply of NAF-No. Dimensions, mm Mass
size 4 bar 5 bar 6 bar kg2)
DN Soft Hard Soft Hard Soft Hard
1)
seat seat* seat seat* seat seat* A B C D E F G H R
300 12 - 20 10 25 16 -2240 700 350 145 239 390 463 797 63 120 61
300 25 20 25 25 25 25 -3140 820 410 200 239 415 515 849 75 120 73
350 5 - 9 - 12 - -2240 700 350 145 264 429 502 861 63 120 80
350 14 - 21 14 25 20 -3140 820 410 200 264 454 554 913 75 120 92
350 25 25 25 25 25 25 -3240 820 410 200 264 454 554 913 75 120 92
400 8 - 12 - 16 10 -3150 820 410 200 296 494 593 984 75 120 123
400 25 16 25 23 25 25 -3250 820 410 200 296 494 593 984 75 120 123
400 25 25 25 25 25 25 -4250 1110 555 260 296 522 654 1045 100 120 139
500 7 - 10 - 18 12 -4160 1110 555 260 382 587 719 1196 100 120 185
500 25 20 25 25 25 25 -4260 1110 555 260 382 587 719 1196 100 120 185
600 12 - 19 12 25 16 -4270 1110 555 260 474 717 801 1370 100 150 326
600 25 25 25 25 25 25 -5170 1680 840 395 474 793 936 1505 150 150 501
300 25 17 25 17 25 17 -3240 1050 640 200 239 415 515 849 75 120 87
300 25 25 25 25 25 25 -4240 1520 965 260 239 443 575 909 100 120 144
350 13 - 13 - 13 - -3240 1050 640 200 264 454 554 913 75 120 106
350 25 25 25 25 25 25 -4240 1520 965 260 264 482 614 973 100 120 163
400 6 - 6 - 6 - -3250 1050 640 200 296 494 593 989 75 120 137
400 25 18 25 18 25 18 -4250 1520 965 260 296 522 654 1045 100 120 194
400 25 25 25 25 25 25 -5250 2210 1370 395 296 559 724 1115 150 120 559
500 10 - 10 - 10 - -4260 1520 965 260 382 587 719 1196 100 120 240
500 25 25 25 25 25 25 -5260 2210 1370 395 382 624 789 1266 150 120 675
600 25 25 25 25 25 25 -5270 2210 1370 395 474 793 936 1505 150 150 766
* Hard seat = Metal and PTFE-seat 1) Including NAF valve positioner 2) Wafer type PN 10-25, ANSI Class 150
6
NAF-Torex butterfly valves
300 - - 20 14 25 20 -3240 1050 640 200 239 415 515 894 75 120 87
300 15 10 25 25 25 25 -4240 1520 965 260 239 443 575 909 100 120 144
350 - - 10 - 22 10 -3240 1050 640 200 264 454 554 913 75 120 106
350 8 - 25 25 25 25 -4240 1520 965 260 264 482 614 973 100 120 163
400 - - 5 - 12 - -3250 1050 640 200 296 494 593 984 75 120 137
400 - - 22 12 25 25 -4250 1520 965 260 296 522 654 1045 100 120 194
400 25 25 25 25 25 25 -5250 2210 1370 395 296 559 724 1115 150 120 559
500 - - 6 - 25 12 -4260 1520 965 260 382 587 719 1196 100 120 240
500 18 12 25 25 25 25 -5260 2210 1370 395 382 624 789 1266 150 120 675
600 - - - - 6 - -4270 1520 965 260 474 717 801 1370 100 150 381
600 6 - 25 22 25 25 -5270 2210 1370 395 474 793 936 1505 150 150 766
* Hard seat = Metal and PTFE-seat 1) Including NAF valve positioner 2) Wafer type PN 10-25, ANSI Class 150
7
Accessories Product code for NAF-Torex
NAF´s pneumatic actuators, see data sheet Fk74.59 Exampel:
can be equipped with a large number of accessories. 23 8 3 A B - 0150 - 06
The following are included in NAF´s standard Code 1 2 3 4 5 6 7
programme and are suitable for direct mounting to
1. Valve type
NAF pneumatic actuators. 23 NAF-Torex
NAF AB
SE-581 87 Linköping
Visiting address: Gelbgjutaregatan 2
Sweden
Tel. +46 13 31 61 00
Telefax +46 13 13 60 54 We reserve the right to design modifications without prior notice
Email: info@naf.se
Website: www.naf.se
An Invensys company ISO 9001 Certified