Professional Documents
Culture Documents
www.veristar.com
Requirements:
BUREAU VERITAS Rules for the Classification of Steel Ships,
BUREAU VERITAS Rules for the Classification of Offshore Units,
IACS UR E16, IACS Rec. 73.
IEC 61537, IEC 60068-2-75, IEC 60093.
FTP Code, Resolution MSC 61(67), Part 2.
This certificate is issued to attest that BUREAU VERITAS did undertake the relevant approval procedures for the product identified above which
was found to comply with the relevant requirements mentioned above.
This certificate remains valid until the date stated above, unless cancelled or revoked, provided the conditions indicated in the subsequent page(s) are complied
with and the product remains satisfactory in service. This certificate will not be valid if the applicant makes any changes or modifications to the approved product,
which have not been notified to, and agreed in writing with BUREAU VERITAS. Should the specified regulations or standards be amended during the validity of
this certificate, the product(s) is/are to be re-approved prior to it/they being placed on board vessels to which the amended regulations or standards apply. This
certificate is issued within the scope of the General Conditions of BUREAU VERITAS Marine Division available on the internet site www.veristar.com. Any
Person not a party to the contract pursuant to which this document is delivered may not assert a claim against BUREAU VERITAS for any liability arising out of
errors or omissions which may be contained in said document, or for errors of judgement, fault or negligence committed by personnel of the Society or of its
Agents in establishment or issuance of this document, and in connection with any activities for which it may provide.
1.1 - Specifications:
Safe Working Load (SWL): IEC 61537 (IACS Rec. 73)
Impact resistance: IEC 60068-2-75 (IACS Rec. 73)
Fire / Flame retardant: URE 10, Test 21/ IEC 60092-101:1999
Smoke emissions and Toxicity: Resolution MSC.61(67) Part 2
Resistivity: IEC 60093 - 1980
As per manufacturer affirmations, compliance with rules/standards ASTM E84-05, ASTM D635-98, ASTM E662-03,
NES 713-83, ASTM D256-03, ASTM D257, ASTM D2565-99, ASTM D2583-92, ASTM D570-98, ASTM D638-03.
width Length
Cable Trays Heavy Description
(mm) (mm)
Cable tray ladder type LCP-3M - LCP-6M 100 to 1000 3 to 6
45°, 90° Flat bend CH90 - CH45 100 to 1000 -
90° Elbow challenger CTO90 100 to 1000 -
90° Flat tees TH90 100 to 1000 -
90° Flat crosshead CZT 100 to 1000 -
45°, 90° Vertical outside bends CVE45 - CVE90 100 to 1000 -
45°, 90° Vertical inside bends CVI45 - CVI90 100 to 1000 -
90° Inversion bends LCX-CI90 100 to 1000 -
90° Vertical tees TVD/S90 100 to 1000 -
Reduction bends RCÉXSX - RD/RE 100 to 1000 -
Accessories / Supports - - -
3. TEST REPORTS:
Stratus:
- Mechanical Test Report 015A/08-rev 01 dated 12/11/2008 - Impact Resistance Test.
- Mechanical Test Report 016A/08-rev 03 dated 26/01/2011 - Safe Load -SWL - Test.
CEPEL:
- Test Report No. DVLF - 46554/08-C dated 10/12/2008.
4.2 - As per BUREAU VERITAS Rules for the Classification of Offshore Units.
5.2 - Production sites are to be recognized by Bureau Veritas as per NR320 for HBV products. To this end STRATUS
COMPOSTOS ESTRUTURAIS LTDA has to make the necessary arrangements for a Society's Surveyor to perform visits and
product audits at the production sites.
5.3 - STRATUS COMPOSTOS ESTRUTURAIS LTDA has declared to Bureau Veritas that the type of product described in
this certificate are manufactured at the following production site:
6. MARKING OF PRODUCT:
The product or packing is to be marked with manufacturer name, type, designation and relevant standards.
7. OTHERS:
This approval is given on the understanding that the Society reserves the right to require check tests to be carried out on the units
at any time and that:
STRATUS COMPOSTOS ESTRUTURAIS LTDA
rua Januária, 581 - Chácaras Reunidas
São José dos Campos
12238 500 São Paulo
BRAZIL
will accept full responsibility for informing shipbuilders, ship-owners and/or their sub-contractors of the proper methods of
fitting and general maintenance of the approved units and the conditions of this approval.