Professional Documents
Culture Documents
Sensor de Oxigeno 2
Sensor de Oxigeno 2
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and
review the general troubleshooting information (see GENERAL
TROUBLESHOOTING INFORMATION ).
NO -Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at
the secondary HO2S (Sensor 2) and the ECM.
NO -Repair short in the wire between the secondary HO2S (Sensor 2) and the No. 3 ALTERNATOR (10
A) fuse. Also replace the No. 3 ALTERNATOR (10 A) fuse, then go to step 23.
Fig. 41: Measuring Resistance Between Secondary Ho2S 4P Connector Terminals 3 And 4
Courtesy of AMERICAN HONDA MOTOR CO., INC.
9. At the secondary HO2S (Sensor 2) side, check for continuity between body ground and secondary HO2S
(Sensor 2) 4P connector terminals No. 3 and No. 4 individually.
Fig. 42: Checking Continuity Between Body Ground And Secondary HO2S 4P Connector
Terminals 3 And 4
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
Fig. 43: Measuring Voltage Between Secondary HO2S 4P Connector Terminals 3 And 4
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Monday, November 25, 2019 7:38:10 PM Page 2 © 2011 Mitchell Repair Information Company, LLC.
2008 Honda Civic Si
2006-11 ENGINE PERFORMANCE PGM-FI System (K20Z3) - Civic
Fig. 44: Checking Continuity Between ECM Connector Terminal B4 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Repair short in the wire between the ECM (B4) and the secondary HO2S (Sensor 2), then go to step
23.
16. Measure the voltage between secondary HO2S (Sensor 2) 4P connector terminal No. 4 and body ground.
Monday, November 25, 2019 7:38:10 PM Page 3 © 2011 Mitchell Repair Information Company, LLC.
2008 Honda Civic Si
2006-11 ENGINE PERFORMANCE PGM-FI System (K20Z3) - Civic
Fig. 45: Measuring Voltage Between Secondary HO2S 4P Connector Terminal 4 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
NO -Repair open in the wire between the secondary HO2S (Sensor 2) and the No. 3 ALTERNATOR (10
A) fuse, then go to step 23.
Fig. 46: Connecting Secondary HO2S 4P Connector Terminal 3 To Body Ground With Jumper
Wire
Courtesy of AMERICAN HONDA MOTOR CO., INC.
21. Check for continuity between ECM connector terminal B4 and body ground.
Monday, November 25, 2019 7:38:10 PM Page 4 © 2011 Mitchell Repair Information Company, LLC.
2008 Honda Civic Si
2006-11 ENGINE PERFORMANCE PGM-FI System (K20Z3) - Civic
Fig. 47: Checking Continuity Between ECM Connector Terminal B4 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
NO -Repair open in the wire between the ECM (B4) and the secondary HO2S (Sensor 2), then go to step
23.
22. Replace the secondary HO2S (Sensor 2) (see SECONDARY HO2S REPLACEMENT ).
23. Reconnect all connectors.
24. Turn the ignition switch to ON (II).
25. Reset the ECM with the HDS.
26. Do the ECM idle learn procedure (see ECM IDLE LEARN PROCEDURE ).
27. Check for Pending or Confirmed or DTCs with the HDS.
YES -Check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM,
then go to step 1.
28. Monitor the OBD STATUS for DTC P0141 in the DTCs MENU with the HDS.
YES -Troubleshooting is complete. If any other Pending or Confirmed or DTCs were indicated in step
27, go to the INDICATED DTC'S TROUBLESHOOTING.
NO -If the screen indicates FAILED, check for poor connections or loose terminals at the secondary
HO2S (Sensor 2) and the ECM, then go to step 1. If the screen indicates NOT COMPLETED, keep idling
Monday, November 25, 2019 7:38:10 PM Page 5 © 2011 Mitchell Repair Information Company, LLC.
2008 Honda Civic Si
2006-11 ENGINE PERFORMANCE PGM-FI System (K20Z3) - Civic
YES -Check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM. If
the ECM was updated, substitute a known-good ECM (see SUBSTITUTING THE ECM ), then go to
step 31. If the ECM was substituted, go to step 1.
33. Monitor the OBD STATUS for DTC P0141 in the DTCs MENU with the HDS.
YES -If the ECM was updated, troubleshooting is complete. If the ECM was substituted, replace the
original ECM (see ECM REPLACEMENT ). If any other Pending or Confirmed or DTCs were
indicated in step 32, go to the INDICATED DTC'S TROUBLESHOOTING.
NO -If the screen indicates FAILED, check for poor connections or loose terminals at the secondary
HO2S (Sensor 2) and the ECM. If the ECM was updated, substitute a known-good ECM (see
SUBSTITUTING THE ECM ), then go to step 31. If the ECM was substituted, go to step 1. If the
screen indicates NOT COMPLETED, keep idling until a result comes on.
Monday, November 25, 2019 7:38:10 PM Page 6 © 2011 Mitchell Repair Information Company, LLC.