Professional Documents
Culture Documents
Buro Happold Limited Four Winds Pacific Quay Glasgow G51 1DY UK Telephone: +44 (0) 141 419 3000 Facsimile: +44 (0) 870 787 4146
Buro Happold Limited Four Winds Pacific Quay Glasgow G51 1DY UK Telephone: +44 (0) 141 419 3000 Facsimile: +44 (0) 870 787 4146
0 FD issue TG April 11 AP
Socket Outlets Back of house areas Recessed MK (UK) Electric Logic Plus White
Fused Connection Units Back of house areas Recessed MK (UK) Electric Logic Plus White
Data Outlets Back of house areas Recessed MK (UK) Electric Logic Plus White
Lighting Switches Back of house areas Recessed MK (UK) Electric Logic Plus White
Socket Outlets Plant and Service areas Surface MK (UK) Electric Metal Clad Plus Aluminum
Fused Connection Units Plant and Service areas Surface MK (UK) Electric Metal Clad Plus Aluminum
Data Outlets Plant and Service areas Surface MK (UK) Electric Metal Clad Plus Aluminum
Lighting Switches Plant and Service areas Surface MK (UK) Electric Metal Clad Plus Aluminum
Notes
1. Front of house areas to include all areas accessable to the public and tenants for office and residential areas.
2. Refer to specifcation for further details and descriptions.
1 of 1
Buro Happold
Notes
1. Refer to specifcation and drawings for further details and description
1 of 1
Buro Happold
Reference General
Location Rating (A) Manufacturer Ambient temp Frequency Mounting Voltage
B1 Tx & RMU Room 3000 ASCO Max 50°C 60Hz Floor 3 phase 380
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
1829 965 2311 2118 Refer to Architectural layouts
Notes
ATS - 1
1. Refer to specifcation for further details and descriptions
2. Unit to supply essential main switchboard EMDB-1
Notes
1 of 3
Buro Happold
Reference General
Location Rating (A) Manufacturer Ambient temp Frequency Mounting Voltage
L10 Plant Room TBC ASCO Max 50°C 60Hz Floor 3 phase 380
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
TBC TBC TBC TBC Refer to Architectural layouts
Notes
ATS - 2
1. Refer to specifcation for further details and descriptions
2. Unit to supply fire pump distribution panel
Notes
2 of 3
Buro Happold
Reference General
Location Rating (A) Manufacturer Ambient temp Frequency Mounting Voltage
L27 Plant Room TBC ASCO Max 50°C 60Hz Floor 3 phase 380
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
TBC TBC TBC TBC Refer to Architectural layouts
Notes
ATS - 3
1. Refer to specifcation for further details and descriptions
2. Unit to supply fire pump distribution panel
Notes
3 of 3
Buro Happold
Reference General
Location Rating (A) Manufacturer Ambient temp Frequency Mounting Voltage
LB1 Plant Room 20KVA Cooper Max 50°C 60Hz Floor 3 phase 380
Physical
Depth (mm) Width (mm) Height (mm) IP Rating Room Dim.'s (m)
400mm 5600 2050 23 Refer to Architectural layouts
Notes
CBU - B1A
1. Refer to specifcation and drawings for further details and descriptions
2. Unit to have 3hour battery duration at full rated load.
3. Outstations as shown on the drawing to 13way. Dimensions 800mm (H) x 600mm (W) x 250mm (D)
4. All equipment to be contained within dedicated cabinet
Notes
1 of 2
Buro Happold
Reference General
Location Rating (A) Manufacturer Ambient temp Frequency Mounting Voltage
LB1 Plant Room 20KVA Cooper Max 50°C 60Hz Floor 3 phase 380
Physical
Depth (mm) Width (mm) Height (mm) IP Rating Room Dim.'s (m)
400mm 5600 2050 23 Refer to Architectural layouts
Notes
CBU - 10A
1. Refer to specifcation and drawings for further details and descriptions
2. Unit to have 3hour battery duration at full rated load.
3. Outstations as shown on the drawing to 13way. Dimensions 800mm (H) x 600mm (W) x 250mm (D)
4. All equipment to be contained within dedicated cabinet
Notes
2 of 2
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
B1 Electrical Plant Room 400 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 1 8No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
3. 1 master unit + 1 slave unit required.
Notes
1 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
B1 Electrical Plant Room 350 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 2 7No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
3. 1 master unit + 1 slave unit required.
Notes
2 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
B1 Electrical Plant Room 250 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 3 5No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
Notes
3 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
B1 Electrical Plant Room 350 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 4 7No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
3. 1 master unit + 1 slave unit required.
Notes
4 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
B1 Electrical Plant Room 400 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 5 8No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
3. 1 master unit + 1 slave unit required.
Notes
5 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
L10 Electrical Plant Rm 250 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 6 5No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
Notes
6 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
L10 Electrical Plant Rm 200 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 7 8No 25KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
Notes
7 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
L10 Electrical Plant Rm 200 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 8 8No 25KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
Notes
8 of 9
Buro Happold
Reference General
Location Rating (kVAr) Manufacturer Range Ambient Temp Mounting
L10 Electrical Plant Rm 250 ABB APC Max 50°C Separate Floor
Physical
Length (mm) Width (mm) Height (mm) Mass(kg) Room Dim.'s (m) IP Rating
600 550 2000 500 Refer to Architectural layouts 23
Technical
Steps Control Short CCT rating Voltage Frequency
PFC 9 7No 50KVAr Maximum Automatic 42kA rms 380 60Hz
Notes
1. All equipment to be contained within purpose made steel IP23 enclosure
2. Enclosure to have forced air ventilation.
Notes
9 of 9
Buro Happold
Voice Controller Main control panel Within Rack Bosch LBB1990 Standard
Routers 6 zone Expansion Router Within Rack Bosch LBB1992 Standard
Remote Controller PA control from additional locations Desk Mounted Bosch LBB1996 Standard
Call Station 6 zone call station Desk Mounted Bosch LBB1956 Standard
Keypad 6 zone call station extension Desk Mounted Bosch LBB 1957 Standard
Recessed Ceiling Speaker Recessed Speaker Ceiling Bosch LC1 RAL T.B.C.
Speaker Cable Fully insulated 100V Line 2 core
Notes
1. Refer to specifcation and drawings for further details and description
2. Each call station, router and the main control panel shall have a separate SPN power supply which shall be derived from dedicated local socket outlets.
3. Contractor shall make allowance for the powder coating of the speakers a RAL colour that will be confirmed by the Project Architech.
4. Interconnecting cabling between control equipment shall be via shielded Cat 5e cable.
1 of 1
Buro Happold
Contents
1.0 Introduction
1.0 Introduction
This document details the calculations for Plot 3.09 for the various electrical systems throughout the building
and should be read in conjunction with all relevant design drawings and documents.
Transformer TX6 L10 - Residential Tower L10 - L11 0.76 1.25 0.80 1.25 0.80
Transformer TX7 L10 - Residential Tower L12 - L17 0.55 1.25 0.80 1.00 0.64
Transformer TX8 L10 - Residential Tower L18 - L23 0.55 1.25 0.80 1.00 0.64
Transformer TX9 L10 - Residential Tower L24 - Roof 0.76 1.25 0.80 1.25 0.80
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 151.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 664.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.94
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.78
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 21.429 / 13.182
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.55 x 106 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 1 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 233.0
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 674.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.92
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.10
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 19.796 / 11.836
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.29 x 106 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 2 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 150.5
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 664.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.53
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.16
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 17.399 / 9.993
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 948.78 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 3 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 286.4
Device Rating In = 800 Overload Setting Ir = 800 [Ir >
_ Ib]
Min. Cable Capacity Iz = 570.8 [BS 7671, Appendix 4.5, Formula (2)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
14.47
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 46.91
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 30.894 / 22.595
Protective Device Breaking Capacity (kA): Icu: 50 Ics: 37.5
Adiabatic Check: CPD Energy Let-through (A²s): 45.00 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 4 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 202.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 670.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.93
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.81
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 16.299 / 9.195
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 809.18 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 5 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 150.9
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 664.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
11.21
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 7.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 23.345 / 14.864
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.49 x 106 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 6 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 200.9
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 670.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.42
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 15.327 / 8.515
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 690.06 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 7 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 344.3
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 696.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
5.97
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 39.510 / 35.219 Load End: 14.464 / 7.927
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 591.43 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 8 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 8.1
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.46
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.40
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.399 / 9.993 Load End: 14.301 / 7.340
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 304.24 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 9 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 3.7
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.46
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.399 / 9.993 Load End: 14.301 / 7.340
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 300.25 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 10 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 141.4
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 277.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.24
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.78
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.399 / 9.993 Load End: 11.275 / 5.822
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 371.10 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 11 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 8.2
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
8.42
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 4.10
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 30.894 / 22.595 Load End: 22.576 / 12.430
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 429.17 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 12 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 7.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
8.42
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 4.08
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 30.894 / 22.595 Load End: 22.576 / 12.430
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 431.60 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 13 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 273.0
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 389.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
5.99
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 3.89
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 30.894 / 22.595 Load End: 16.610 / 8.842
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 747.38 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 14 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.9
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.13
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.32
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.299 / 9.195 Load End: 13.538 / 6.898
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 288.34 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 15 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 6.5
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.13
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.299 / 9.195 Load End: 13.538 / 6.898
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 283.69 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 16 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 190.2
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 290.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.04
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.71
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.299 / 9.195 Load End: 10.796 / 5.540
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 356.98 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 17 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.15
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.81
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.345 / 14.864 Load End: 18.203 / 9.694
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.98 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 18 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.2
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.15
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.79
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.345 / 14.864 Load End: 18.203 / 9.694
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.52 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 19 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 144.8
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 278.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.53
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.345 / 14.864 Load End: 12.489 / 6.093
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 383.27 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 20 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.85
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 15.327 / 8.515 Load End: 12.852 / 6.507
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 274.24 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 21 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 6.5
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.85
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.02
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 15.327 / 8.515 Load End: 12.852 / 6.507
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 269.00 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 22 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 191.2
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 290.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.86
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 15.327 / 8.515 Load End: 10.357 / 5.283
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 344.16 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 23 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.9
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.61
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.69
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.429 / 13.182 Load End: 16.984 / 8.940
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 361.85 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 24 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 3.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.61
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.65
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.429 / 13.182 Load End: 16.984 / 8.940
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 360.26 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 25 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 144.8
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 278.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.31
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.80
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.429 / 13.182 Load End: 11.906 / 5.789
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 369.47 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 26 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 6.2
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.59
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.09
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 14.464 / 7.927 Load End: 12.232 / 6.157
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 261.65 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 27 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 6.4
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.59
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.90
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 14.464 / 7.927 Load End: 12.232 / 6.157
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 255.88 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 28 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 186.4
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 289.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.69
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.65
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 14.464 / 7.927 Load End: 9.951 / 5.050
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 332.48 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 29 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 147.6
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 278.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.69
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.65
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 14.464 / 7.927 Load End: 9.951 / 5.050
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 332.48 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 30 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 7.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 104.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.15
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.57
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.796 / 11.836 Load End: 15.918 / 8.295
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 338.62 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 31 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 5.7
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.22
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.796 / 11.836 Load End: 14.303 / 7.105
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 291.42 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 32 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 136.4
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 276.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.11
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.74
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.796 / 11.836 Load End: 11.375 / 5.514
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 355.70 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 33 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 84.1
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 176.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
4.11
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.796 / 11.836 Load End: 11.375 / 5.514
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 278.13 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 34 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.96 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 2,400.0
Device Rating In = 3200 Overload Setting Ir = 2560 [Ir >
_ Ib]
Min. Cable Capacity Iz = 925.9 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
27.10
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 88.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 44.711 / 44.710 Load End: 39.510 / 35.219
Protective Device Breaking Capacity (kA): Icu: 125 Ics: 93.7
Adiabatic Check: CPD Energy Let-through (A²s): 160.00 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Project: KAFD 3.09 Tx 1 & Gen rev 2.p17 Page 35 of 35 Printed on: 17/01/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Buro Happold
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 146.6
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 663.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.06
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.89
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 16.217 / 9.743
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 905.05 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 401.6
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 710.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 741.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
5.02
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 12.344 / 6.853
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 465.11 x 103 Adiabatic Limit k²S² (A²s): 3,271.84 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 46.0
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 334.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.79
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 3.37
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 13.168 / 6.926
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 444.31 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 62.7
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 336.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
3.29
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 8.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 9.708 / 4.758
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 229.24 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 46.0
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 334.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.39
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 3.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 12.299 / 6.350
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 360.75 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 59.8
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 335.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
3.09
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 8.10
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 9.219 / 4.476
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 210.94 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 96.5
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 339.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.05
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 3.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 11.534 / 5.861
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 300.96 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 116.8
Device Rating In = 400 Overload Setting Ir = 320 [Ir >
_ Ib]
Min. Cable Capacity Iz = 342.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 456.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
3.21
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 8.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.860 / 25.000 Load End: 8.775 / 4.226
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 194.66 x 103 Adiabatic Limit k²S² (A²s): 699.87 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 39.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 107.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.26
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.93
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 11.106 / 5.844
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 250.37 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.6
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 83.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.04
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.64
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 10.720 / 5.514
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 223.26 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 159.3
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 281.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.53
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 3.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 9.387 / 4.853
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 322.63 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 30.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 106.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.66
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 2.04
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 7.553 / 3.597
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 135.80 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 64.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 112.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.75
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 9.934 / 5.082
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 222.95 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 112.0
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 183.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
4.31
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.31
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.344 / 6.853 Load End: 11.036 / 5.854
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 293.45 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 118.3
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 184.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.26
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.217 / 9.743 Load End: 13.594 / 7.267
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 334.84 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 26.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 85.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.26
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.20
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.217 / 9.743 Load End: 13.594 / 7.267
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 297.50 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1.4
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 166.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.71
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.06
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.217 / 9.743 Load End: 10.166 / 5.051
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 257.31 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 46.9
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 108.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.88
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 9.708 / 4.758 Load End: 8.786 / 4.176
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 170.57 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 22.3
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
2.75
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.04
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 9.708 / 4.758 Load End: 8.482 / 3.976
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 138.95 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 27.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 105.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.75
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 13.168 / 6.926 Load End: 11.085 / 5.408
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 234.70 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 18.6
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.75
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.51
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 13.168 / 6.926 Load End: 11.085 / 5.408
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 217.46 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 44.1
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 108.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.73
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.07
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 9.219 / 4.476 Load End: 8.379 / 3.956
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 157.39 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 19.4
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
2.61
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.97
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 9.219 / 4.476 Load End: 8.101 / 3.776
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 130.15 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 27.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 105.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.49
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.52
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.299 / 6.350 Load End: 10.445 / 5.045
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 221.62 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 18.6
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.49
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.40
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 12.299 / 6.350 Load End: 10.445 / 5.045
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 197.48 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 48.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 109.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.82
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.12
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 8.775 / 4.226 Load End: 8.008 / 3.759
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 145.52 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 23.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
2.70
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.01
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 8.775 / 4.226 Load End: 7.752 / 3.595
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 122.19 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 45.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 108.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.22
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 1.79
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 8.775 / 4.226 Load End: 6.466 / 2.945
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 97.59 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 30.7
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 106.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.27
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.534 / 5.861 Load End: 9.875 / 4.727
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 203.65 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.1
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 84.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.27
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.30
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.534 / 5.861 Load End: 9.875 / 4.727
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 180.01 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 109.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.59
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 2.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.534 / 5.861 Load End: 7.884 / 3.665
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 139.88 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Comments
Rating Factors
Air Temperature(°C) = 35.0 Ca = 0.96 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.93 [BS 7671, Table 4C5]
No. of ladders = 2 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,700.0
Device Rating In = 2000 Overload Setting Ir = 1800 [Ir >
_ Ib]
Min. Cable Capacity Iz = 672.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
17.29
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 88.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 36.627 / 36.627 Load End: 29.860 / 25.000
Protective Device Breaking Capacity (kA): Icu: 85 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 160.00 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 217.7
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.28
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 4.14
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.719 / 12.133 Load End: 17.064 / 11.425
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.01 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =5 Cg = 0.75 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 5
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 355.3
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 544.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
5.00
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 3.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.692 / 12.101 Load End: 14.092 / 8.625
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 709.44 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 431.3
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.31
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.560 / 11.941 Load End: 17.232 / 11.587
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.25 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 341.7
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 538.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 150 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.43
Adiabatic check (mm 2 ) CPC Section = Separate 150 Total = 150.0 Min. Section = 4.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.013 / 15.873 Load End: 15.961 / 10.235
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 960.59 x 103 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 542.1
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.99
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.904 / 15.716 Load End: 20.453 / 15.127
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.42 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 259.7
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.90
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 6.08
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.049 / 15.926 Load End: 20.152 / 14.762
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.16 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.49 Maximum for circuit: 5.00
0.55
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 7.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 1.788 / 0.709
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 15.92 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.92 Maximum for circuit: 5.00
0.48
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 6.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 1.550 / 0.613
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 14.00 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.96 Maximum for circuit: 5.00
0.47
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 6.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 1.534 / 0.607
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 14.00 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,004.3
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 704.6 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
6.72
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 17.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 18.043 / 12.533
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 173.06 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,143.5
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 704.6 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
9.77
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 25.58
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 21.491 / 16.580
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 173.06 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.84
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.98
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 2.694 / 1.077
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 26.20 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.83
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.97
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 2.647 / 1.057
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 25.67 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.57 Maximum for circuit: 5.00
0.53
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 7.06
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 1.727 / 0.684
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 15.23 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.60 Maximum for circuit: 5.00
0.53
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 7.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.339 / 23.867 Load End: 1.707 / 0.676
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 15.01 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 60.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 123.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.55
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 15.808 / 9.791
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 392.48 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 30.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 94.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.33
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 15.458 / 9.331
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 374.92 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 108.1
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 200.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.90
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 2.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 9.459 / 4.646
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 239.06 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 98.3
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 198.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.35
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 10.819 / 5.439
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 274.76 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 106.2
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 200.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.26
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.81
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 10.570 / 5.268
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 267.05 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 28.8
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 94.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.92
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.56
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.232 / 11.587 Load End: 6.106 / 2.593
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 78.09 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 60.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 123.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.53
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.90
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 18.556 / 12.283
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 427.40 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 30.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 94.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.11
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.78
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 18.090 / 11.567
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 420.37 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 21.6
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.58
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.40
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 4.985 / 2.057
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.52 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 129.0
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 250.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
4.33
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 3.51
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 12.732 / 6.767
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.33 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 135.1
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 252.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.74
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 3.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 11.387 / 5.794
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 339.68 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 42.1
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 97.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.35
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.29
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 4.292 / 1.754
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.11 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 39.5
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 96.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.36
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.29
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 5.149 / 2.145
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.36 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 42.6
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 97.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.68
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 5.762 / 2.448
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 71.70 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =9 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 9
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 42.2
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 97.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.38
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.30
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.453 / 15.127 Load End: 5.212 / 2.173
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 59.61 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =5 Cg = 0.75 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 5
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 80.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 127.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.52
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.064 / 11.425 Load End: 15.662 / 9.672
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.21 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =5 Cg = 0.75 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 5
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 40.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 96.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.30
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.064 / 11.425 Load End: 15.317 / 9.223
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 370.88 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =5 Cg = 0.75 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 5
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 25.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.01
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.09
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.064 / 11.425 Load End: 13.920 / 7.516
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 306.86 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =5 Cg = 0.75 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 5
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 72.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 152.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.50
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.10
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.064 / 11.425 Load End: 8.369 / 3.831
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 169.88 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 80.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 129.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.45
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.88
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 18.295 / 12.025
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 424.30 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 40.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 96.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.03
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.76
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 17.838 / 11.336
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 417.37 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 25.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.49
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 15.957 / 8.801
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 355.04 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 39.7
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 96.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.97
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 7.989 / 3.487
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 117.41 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 45.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 97.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.93
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.56
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 7.046 / 3.040
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 97.78 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 94.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.56
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 20.152 / 14.762 Load End: 4.682 / 1.937
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 50.23 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,519.4
Device Rating In = 2000 Overload Setting Ir = 2000 [Ir >
_ Ib]
Min. Cable Capacity Iz = 592.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 1.72 Maximum for circuit: 5.00
17.35
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 159.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.229 / 29.229 Load End: 26.339 / 23.867
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: Max. disconnection time (s) = (k²S²/I²): 14.25 Actual disconnection time (s) = 0.14
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 70.0
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.37
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 4.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.002 / 15.990 Load End: 21.913 / 14.781
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.17 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 1 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 720.2
Device Rating In = 800 Overload Setting Ir = 800 [Ir >
_ Ib]
Min. Cable Capacity Iz = 522.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
5.48
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 46.91
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.864 / 15.815 Load End: 17.994 / 11.040
Protective Device Breaking Capacity (kA): Icu: 50 Ics: 37.5
Adiabatic Check: CPD Energy Let-through (A²s): 45.00 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 2 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.44
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.11
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.830 / 15.772 Load End: 22.280 / 15.160
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.42 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 3 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.38
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.08
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.659 / 15.560 Load End: 22.116 / 14.961
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.46 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 4 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.32
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.05
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.490 / 15.352 Load End: 21.953 / 14.767
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.51 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 5 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 70.0
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.68
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 6.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.906 / 19.307 Load End: 24.552 / 17.603
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.29 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 6 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 556.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.72
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.69
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.735 / 19.062 Load End: 19.809 / 12.479
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.41 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 7 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.79
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.69
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.692 / 19.001 Load End: 25.009 / 18.137
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 686.39 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 8 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.69
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.481 / 18.704 Load End: 24.806 / 17.861
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 754.17 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 9 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.59
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.56
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.272 / 18.412 Load End: 24.606 / 17.590
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 820.43 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 10 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.1
Device Rating In = 20 Motor Overload Setting Ir = 1.07 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.44
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 1.158 / 0.768
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 11 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.1
Device Rating In = 20 Motor Overload Setting Ir = 1.07 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.44
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 1.158 / 0.768
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 12 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.1
Device Rating In = 20 Motor Overload Setting Ir = 1.07 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.44
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 1.158 / 0.768
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 13 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 32.2
Device Rating In = 40 Motor Overload Setting Ir = 32.18 [Ir >
_ Ib]
Min. Cable Capacity Iz = 51.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 4.668 / 2.907
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 138.95 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 14 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 32.2
Device Rating In = 40 Motor Overload Setting Ir = 32.18 [Ir >
_ Ib]
Min. Cable Capacity Iz = 51.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 4.668 / 2.907
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 138.95 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 15 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.20
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.258 / 2.081
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 85.24 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 16 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.20
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.258 / 2.081
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 85.24 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 17 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 270.4
Device Rating In = 400 Overload Setting Ir = 280 [Ir >
_ Ib]
Min. Cable Capacity Iz = 431.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.34
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 3.14
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 14.244 / 7.977
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 596.70 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 18 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.42
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.69
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.870 / 2.444
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 108.89 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 19 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.42
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.69
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.870 / 2.444
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 108.89 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 20 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.64
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.642 / 2.310
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 100.16 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 21 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.64
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.642 / 2.310
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 100.16 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 22 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 165.6
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 264.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 346.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 70 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.94
Adiabatic check (mm 2 ) CPC Section = Separate 70 Total = 70.0 Min. Section = 3.30
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 13.074 / 6.872
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 393.58 x 103 Adiabatic Limit k²S² (A²s): 294.47 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 23 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.14
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.094 / 1.982
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 79.32 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 24 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.14
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 3.094 / 1.982
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 79.32 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 25 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.68
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 1.796 / 1.178
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 26 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.68
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 1.796 / 1.178
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 27 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 18 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 176.2
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 281.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.32
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 2.95
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.994 / 11.040 Load End: 11.511 / 5.712
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 335.61 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 28 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 3.3
Device Rating In = 20 Motor Overload Setting Ir = 3.26 [Ir >
_ Ib]
Min. Cable Capacity Iz = 5.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.98
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.580 / 1.677
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 67.87 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 29 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 3.3
Device Rating In = 20 Motor Overload Setting Ir = 3.26 [Ir >
_ Ib]
Min. Cable Capacity Iz = 5.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.98
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.580 / 1.677
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 67.87 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 30 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.705 / 1.755
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.80 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 31 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.705 / 1.755
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.80 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 32 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.96
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.537 / 1.650
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 66.87 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 33 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.96
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 2.537 / 1.650
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 66.87 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 34 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 145.9
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 232.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.91
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 10.015 / 4.621
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 237.93 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 35 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
0.68
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.793 / 1.179
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 36 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 23.9
Device Rating In = 40 Motor Overload Setting Ir = 23.86 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
0.68
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.793 / 1.179
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 37 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.40
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.028 / 0.684
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 38 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.40
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.028 / 0.684
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 39 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 176.2
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 281.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.72
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 2.72
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 9.285 / 4.301
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 249.35 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 40 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.1
Device Rating In = 20 Motor Overload Setting Ir = 1.07 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.38
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 0.999 / 0.665
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 41 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.1
Device Rating In = 20 Motor Overload Setting Ir = 1.07 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.38
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 0.999 / 0.665
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 42 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.70
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.847 / 1.214
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 43 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.70
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.847 / 1.214
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 44 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.41
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.058 / 0.704
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 45 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.41
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 1.058 / 0.704
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 46 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 145.9
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 232.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.28
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 8.018 / 3.549
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 180.70 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 47 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 1.7
Device Rating In = 20 Motor Overload Setting Ir = 1.68 [Ir >
_ Ib]
Min. Cable Capacity Iz = 1.9 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 63.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 0.40
0.37
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.809 / 12.479 Load End: 0.486 / 0.373
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 48 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.05
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 3.042 / 1.361
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 56.05 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 49 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.25
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 3.779 / 1.520
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.57 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 50 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 3.887 / 1.572
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 40.05 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 51 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.21
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.400 / 3.143 Load End: 3.966 / 1.838
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.92 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 52 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.36
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.29
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.400 / 3.143 Load End: 4.602 / 1.862
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 48.16 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 53 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.400 / 3.143 Load End: 4.581 / 1.866
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 48.26 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 54 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 2.900 / 1.318
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.44 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 55 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 3.642 / 1.462
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.96 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 56 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.374 / 2.216 Load End: 4.124 / 1.675
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 42.93 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 57 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.706 Load End: 3.283 / 1.533
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.47 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 58 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.706 Load End: 4.214 / 1.696
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.51 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 59 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.28
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.25
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.706 Load End: 4.717 / 1.921
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.78 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 60 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.663 Load End: 3.345 / 1.544
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.91 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 61 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.663 Load End: 4.261 / 1.716
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 44.08 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 62 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.15
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.663 Load End: 4.217 / 1.707
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.82 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 63 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.17
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.023 / 2.948 Load End: 3.840 / 1.756
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.86 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 64 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.31
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.27
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.023 / 2.948 Load End: 4.436 / 1.789
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 46.10 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 65 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.023 / 2.948 Load End: 4.915 / 2.005
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 52.24 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 66 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.05
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 3.038 / 1.359
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.97 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 67 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 3.774 / 1.517
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.51 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 68 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 3.881 / 1.570
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 39.98 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 69 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.20
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.132 Load End: 3.960 / 1.834
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.77 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 70 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.36
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.29
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.132 Load End: 4.594 / 1.859
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 48.06 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 71 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.132 Load End: 4.573 / 1.863
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 48.16 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 72 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 2.897 / 1.316
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.36 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 73 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 3.637 / 1.459
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.90 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 74 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.362 / 2.211 Load End: 4.117 / 1.672
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 42.85 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 75 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.477 / 2.699 Load End: 3.279 / 1.530
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.37 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 76 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.477 / 2.699 Load End: 4.207 / 1.693
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.43 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 77 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.28
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.25
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.477 / 2.699 Load End: 4.708 / 1.917
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.68 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 78 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.381 / 2.655 Load End: 3.341 / 1.542
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.81 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 79 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.381 / 2.655 Load End: 4.254 / 1.713
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.99 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 80 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.15
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.381 / 2.655 Load End: 4.210 / 1.704
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.74 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 81 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.17
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.003 / 2.939 Load End: 3.834 / 1.753
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.72 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 82 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.31
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.003 / 2.939 Load End: 4.429 / 1.786
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 46.01 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 83 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.003 / 2.939 Load End: 4.906 / 2.001
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 52.05 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 84 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.05
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 3.035 / 1.357
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.89 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 85 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 3.768 / 1.515
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.44 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 86 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 4.192 / 1.704
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.73 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 87 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.20
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.356 / 3.122 Load End: 3.954 / 1.830
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.62 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 88 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.35
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.29
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.356 / 3.122 Load End: 4.585 / 1.855
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.96 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 89 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.25
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.356 / 3.122 Load End: 4.564 / 1.859
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 48.06 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 90 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 2.893 / 1.314
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.28 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 91 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 3.632 / 1.457
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.84 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 92 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.351 / 2.206 Load End: 4.111 / 1.669
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 42.76 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 93 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.460 / 2.691 Load End: 3.275 / 1.527
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.26 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 94 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.460 / 2.691 Load End: 4.200 / 1.690
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.35 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 95 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.25
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.460 / 2.691 Load End: 4.699 / 1.913
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.57 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 96 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.364 / 2.648 Load End: 3.337 / 1.539
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.70 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 97 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.364 / 2.648 Load End: 4.247 / 1.710
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.91 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 98 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.15
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.364 / 2.648 Load End: 4.203 / 1.701
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.65 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 99 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.984 / 2.930 Load End: 3.828 / 1.749
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.59 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 100 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.31
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.984 / 2.930 Load End: 4.421 / 1.782
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.92 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 101 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.984 / 2.930 Load End: 4.896 / 1.997
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 51.92 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 102 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 2 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,526.8
Device Rating In = 2000 Overload Setting Ir = 2000 [Ir >
_ Ib]
Min. Cable Capacity Iz = 660.6 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
8.07
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 21.11
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 32.664 / 29.340 Load End: 23.748 / 16.955
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 270.40 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 103 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 2 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,170.0
Device Rating In = 2000 Overload Setting Ir = 2000 [Ir >
_ Ib]
Min. Cable Capacity Iz = 660.6 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
10.87
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 28.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 32.664 / 29.340 Load End: 26.830 / 20.661
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 270.40 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 104 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 118.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.32
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.913 / 14.781 Load End: 19.605 / 11.906
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 422.87 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 105 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.02
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.913 / 14.781 Load End: 19.035 / 11.196
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 415.55 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 106 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 118.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.94
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.552 / 17.603 Load End: 21.750 / 13.709
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 444.51 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 107 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.43
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.85
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.552 / 17.603 Load End: 21.056 / 12.768
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 435.99 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 108 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.38
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 19.914 / 12.163
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 425.95 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 109 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.07
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.52
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 19.329 / 11.424
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 418.52 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 110 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.59
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.16
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 9.107 / 4.026
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 181.55 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 111 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.15
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.51
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 10.932 / 5.018
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 241.07 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 112 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.63
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 9.249 / 4.100
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 185.99 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 113 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.72
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 5.374 / 2.216
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.12 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 114 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.93
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 7.400 / 3.143
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 165.36 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 115 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.72
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.280 / 15.160 Load End: 5.374 / 2.216
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.12 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 116 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
8.04
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 4.01
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 22.130 / 14.052
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 448.62 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 117 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.52
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.88
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 21.416 / 13.066
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 439.86 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 118 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.06
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 10.332 / 4.624
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 217.44 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 119 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.64
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.20
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 9.059 / 3.963
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 177.80 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 120 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.38
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.64
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 11.309 / 5.158
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 249.51 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 121 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.70
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 6.494 / 2.706
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.80 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 122 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.67
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 6.397 / 2.663
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.47 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 123 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.85
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.009 / 18.137 Load End: 7.023 / 2.948
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.61 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 124 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.33
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 19.770 / 12.018
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 424.22 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 125 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.03
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 19.190 / 11.294
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 416.82 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 126 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.58
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 9.073 / 4.009
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 180.51 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 127 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.14
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 10.884 / 4.991
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 239.46 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 128 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 9.214 / 4.082
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 184.92 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 129 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.72
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 5.362 / 2.211
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.09 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 130 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.93
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 7.378 / 3.132
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 164.60 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 131 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.72
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.116 / 14.961 Load End: 5.362 / 2.211
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.09 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 132 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.96
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 4.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 21.953 / 13.859
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 446.30 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 133 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.45
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 21.246 / 12.895
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 437.63 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 134 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.04
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 10.288 / 4.601
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 216.08 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 135 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.63
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 9.026 / 3.947
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 176.81 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 136 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.37
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.64
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 11.257 / 5.130
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 247.81 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 137 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 6.477 / 2.699
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.74 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 138 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.67
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 6.381 / 2.655
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.41 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 139 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.84
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.806 / 17.861 Load End: 7.003 / 2.939
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.54 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 140 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.41
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 17.463 / 9.692
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.91 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 141 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.88
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.04
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 16.395 / 8.665
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 349.93 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 142 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.57
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 9.039 / 3.992
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 179.49 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 143 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.12
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 10.835 / 4.965
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 237.87 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 144 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.61
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 9.179 / 4.064
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 183.86 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 145 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.71
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 5.351 / 2.206
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.05 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 146 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.92
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 7.356 / 3.122
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 163.85 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 147 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.71
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.953 / 14.767 Load End: 5.351 / 2.206
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 149.05 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 148 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.88
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.98
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 21.778 / 13.671
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 444.05 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 149 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.38
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.84
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 21.078 / 12.728
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 435.46 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 150 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.03
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.44
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 10.245 / 4.579
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 214.74 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 151 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 8.993 / 3.930
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 175.82 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 152 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.35
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 11.205 / 5.102
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 246.13 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 153 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 6.460 / 2.691
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.68 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 154 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.66
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 6.364 / 2.648
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.36 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 155 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.84
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 24.606 / 17.590 Load End: 6.984 / 2.930
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.47 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 156 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,944.2
Device Rating In = 2500 Overload Setting Ir = 2500 [Ir >
_ Ib]
Min. Cable Capacity Iz = 740.6 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.77 Maximum for circuit: 5.00
20.85
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 283.12
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 36.627 / 36.627 Load End: 32.664 / 29.340
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 422.50 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Project: KAFD 3.09 Tx 4 rev 0.p17 Page 157 of 157 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Buro Happold
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.25
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.589 / 15.043 Load End: 22.994 / 14.476
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.58 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 1 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.17
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.96
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.350 / 14.788 Load End: 22.765 / 14.237
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.64 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 2 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.10
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.91
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.114 / 14.540 Load End: 22.539 / 14.005
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.70 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 3 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 421.4
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.02
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.882 / 14.300 Load End: 22.317 / 13.779
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.66 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 4 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.84
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.72
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 27.128 / 18.433 Load End: 26.356 / 17.600
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 818.04 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 5 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.70
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.819 / 18.060 Load End: 26.061 / 17.255
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 902.58 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 6 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.57
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.54
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.514 / 17.699 Load End: 25.770 / 16.921
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 984.33 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 7 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 408.7
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
9.44
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.215 / 17.351 Load End: 25.485 / 16.598
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.06 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 8 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.04
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 3.039 / 1.353
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.73 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 9 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 3.776 / 1.510
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.31 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 10 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 3.884 / 1.562
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 39.77 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 11 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.20
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.406 / 3.103 Load End: 3.961 / 1.822
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.32 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 12 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.35
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.406 / 3.103 Load End: 4.597 / 1.848
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.76 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 13 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.25
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.406 / 3.103 Load End: 4.578 / 1.852
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.87 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 14 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 2.897 / 1.310
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.13 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 15 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 3.638 / 1.453
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.72 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 16 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.19
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.20
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.372 / 2.196 Load End: 3.788 / 1.522
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.65 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 17 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.515 / 2.684 Load End: 3.284 / 1.524
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.16 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 18 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.515 / 2.684 Load End: 4.217 / 1.687
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.27 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 19 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.515 / 2.684 Load End: 4.724 / 1.910
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.47 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 20 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.418 / 2.641 Load End: 3.346 / 1.536
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.60 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 21 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.418 / 2.641 Load End: 4.264 / 1.707
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.83 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 22 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.15
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.418 / 2.641 Load End: 4.222 / 1.698
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.58 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 23 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.050 / 2.922 Load End: 3.842 / 1.746
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.46 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 24 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.31
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.050 / 2.922 Load End: 4.440 / 1.779
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.83 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 25 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.050 / 2.922 Load End: 4.924 / 1.993
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 51.81 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 26 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.04
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 3.034 / 1.350
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.62 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 27 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 3.769 / 1.507
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.23 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 28 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 3.877 / 1.559
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 39.68 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 29 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.19
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.090 Load End: 3.954 / 1.817
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.13 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 30 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.090 Load End: 4.587 / 1.844
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.64 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 31 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.25
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.378 / 3.090 Load End: 4.568 / 1.848
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.74 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 32 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 2.893 / 1.308
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.04 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 33 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 3.632 / 1.450
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.64 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 34 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.19
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.20
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.358 / 2.190 Load End: 3.781 / 1.519
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.56 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 35 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.675 Load End: 3.279 / 1.521
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.03 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 36 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.675 Load End: 4.209 / 1.684
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.16 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 37 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.494 / 2.675 Load End: 4.713 / 1.905
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.34 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 38 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.632 Load End: 3.341 / 1.532
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.47 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 39 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.632 Load End: 4.255 / 1.704
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.72 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 40 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.15
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.397 / 2.632 Load End: 4.213 / 1.695
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.47 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 41 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.025 / 2.910 Load End: 3.834 / 1.741
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.28 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 42 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.30
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.025 / 2.910 Load End: 4.431 / 1.775
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.71 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 43 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.33
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.025 / 2.910 Load End: 4.912 / 1.988
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 51.67 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 44 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.04
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 3.030 / 1.347
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.52 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 45 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 3.762 / 1.504
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.15 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 46 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 3.869 / 1.556
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 39.59 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 47 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.19
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.350 / 3.077 Load End: 3.946 / 1.812
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 72.95 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 48 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.350 / 3.077 Load End: 4.576 / 1.839
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.51 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 49 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.350 / 3.077 Load End: 4.557 / 1.843
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.62 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 50 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 2.889 / 1.305
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.94 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 51 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 3.625 / 1.448
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.56 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 52 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.18
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.20
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.343 / 2.184 Load End: 3.774 / 1.516
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.48 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 53 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.472 / 2.665 Load End: 3.273 / 1.517
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 61.90 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 54 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.472 / 2.665 Load End: 4.200 / 1.680
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.06 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 55 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.472 / 2.665 Load End: 4.702 / 1.900
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.20 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 56 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.02
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.376 / 2.623 Load End: 3.336 / 1.529
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.33 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 57 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.23
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.376 / 2.623 Load End: 4.247 / 1.700
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.61 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 58 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.14
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.376 / 2.623 Load End: 4.204 / 1.691
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.36 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 59 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.000 / 2.899 Load End: 3.827 / 1.736
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 70.11 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 60 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.30
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.000 / 2.899 Load End: 4.421 / 1.771
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.60 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 61 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.33
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.000 / 2.899 Load End: 4.900 / 1.983
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 51.52 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 62 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.04
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 3.025 / 1.344
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 55.42 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 63 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 3.755 / 1.501
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.06 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 64 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.21
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 3.862 / 1.553
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 39.50 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 65 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.19
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.322 / 3.064 Load End: 3.938 / 1.807
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 72.76 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 66 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.28
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.322 / 3.064 Load End: 4.566 / 1.835
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.39 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 67 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.24
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.23
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 7.322 / 3.064 Load End: 4.547 / 1.839
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 47.49 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 68 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.99
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 2.885 / 1.302
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.84 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 69 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 3.619 / 1.445
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.49 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 70 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.18
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 5.329 / 2.177 Load End: 3.767 / 1.513
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 38.39 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 71 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.00
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.451 / 2.656 Load End: 3.268 / 1.514
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 61.77 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 72 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.451 / 2.656 Load End: 4.191 / 1.676
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 42.96 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 73 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.24
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.451 / 2.656 Load End: 4.691 / 1.895
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 49.07 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 74 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.355 / 2.614 Load End: 3.330 / 1.525
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.20 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 75 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.22
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.355 / 2.614 Load End: 4.238 / 1.696
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.51 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 76 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.14
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.355 / 2.614 Load End: 4.196 / 1.687
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.26 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 77 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 14.5
Device Rating In = 20 Motor Overload Setting Ir = 14.54 [Ir >
_ Ib]
Min. Cable Capacity Iz = 20.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.975 / 2.888 Load End: 3.820 / 1.732
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 69.94 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 78 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 22.8
Device Rating In = 32 Overload Setting Ir = 32 [Ir >
_ Ib]
Min. Cable Capacity Iz = 38.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.30
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.26
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.975 / 2.888 Load End: 4.411 / 1.767
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 45.48 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 79 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.6
Device Rating In = 50 Overload Setting Ir = 50 [Ir >
_ Ib]
Min. Cable Capacity Iz = 63.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.33
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.27
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 6.975 / 2.888 Load End: 4.888 / 1.978
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 51.38 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 80 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.58
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 1.879 / 0.742
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 16.84 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 81 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.42 Maximum for circuit: 5.00
0.57
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 7.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 1.856 / 0.732
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 16.58 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 82 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 3.41 Maximum for circuit: 5.00
0.58
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 7.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 1.868 / 0.737
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 16.71 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 83 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.63
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 2.515 / 0.999
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 24.04 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 84 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 2 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,180.0
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 528.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
8.22
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 21.51
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 25.699 / 17.421
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 173.06 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 85 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 2 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,144.2
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 528.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
11.67
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 91.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 29.866 / 21.948
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 192.90 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 86 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.79
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.95
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 2.564 / 1.016
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 24.50 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 87 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.77
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.93
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 35.973 / 29.944 Load End: 2.480 / 0.982
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 23.55 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 88 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.21
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 20.393 / 11.650
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 419.80 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 89 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.90
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 19.750 / 10.957
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 412.44 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 90 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.55
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.13
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 9.133 / 3.960
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 177.61 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 91 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.09
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.48
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 10.987 / 4.917
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 234.99 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 92 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.59
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.16
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 9.277 / 4.032
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 181.91 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 93 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.70
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 5.372 / 2.196
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.97 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 94 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.91
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 7.406 / 3.103
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 162.44 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 95 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.70
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.994 / 14.476 Load End: 5.372 / 2.196
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.97 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 96 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
8.00
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 4.00
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 23.058 / 13.617
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 443.41 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 97 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.46
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 22.242 / 12.667
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 434.67 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 98 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.03
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.44
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 10.429 / 4.562
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 213.73 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 99 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 9.126 / 3.917
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 175.05 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 100 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.35
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 11.435 / 5.082
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 244.92 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 101 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 6.515 / 2.684
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.63 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 102 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.66
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 6.418 / 2.641
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.31 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 103 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.84
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.356 / 17.600 Load End: 7.050 / 2.922
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.41 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 104 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.15
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.57
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 20.196 / 11.479
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 417.74 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 105 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.84
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.44
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 19.562 / 10.802
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 410.42 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 106 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.54
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.12
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 9.089 / 3.939
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 176.33 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 107 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.08
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.47
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 10.924 / 4.884
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 233.02 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 108 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.58
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 9.232 / 4.010
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 180.58 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 109 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.70
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 5.358 / 2.190
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.93 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 110 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.90
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 7.378 / 3.090
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 161.50 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 111 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.70
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.765 / 14.237 Load End: 5.358 / 2.190
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.93 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 112 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.89
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.98
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 22.807 / 13.383
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 440.59 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 113 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.37
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.84
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 22.004 / 12.460
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 431.97 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 114 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.01
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 10.372 / 4.534
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 212.03 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 115 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.61
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 9.082 / 3.897
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 173.80 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 116 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.33
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 11.367 / 5.047
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 242.82 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 117 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.68
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 6.494 / 2.675
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.56 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 118 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.66
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 6.397 / 2.632
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.24 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 119 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.83
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.061 / 17.255 Load End: 7.025 / 2.910
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.33 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 120 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.09
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.56
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 20.003 / 11.312
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 415.75 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 121 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.79
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.41
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 19.377 / 10.652
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 408.47 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 122 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.53
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.12
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 9.046 / 3.918
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 175.07 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 123 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.06
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.46
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 10.861 / 4.851
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 231.08 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 124 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.57
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.14
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 9.187 / 3.988
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 179.28 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 125 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 5.343 / 2.184
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.88 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 126 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.90
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 7.350 / 3.077
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 160.57 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 127 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.539 / 14.005 Load End: 5.343 / 2.184
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.88 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 128 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.79
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.96
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 22.562 / 13.157
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 437.88 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 129 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.27
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.82
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 21.770 / 12.259
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 429.37 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 130 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.00
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 10.316 / 4.506
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 210.37 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 131 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.60
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.16
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 9.039 / 3.876
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 172.57 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 132 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.31
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 11.300 / 5.012
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 240.75 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 133 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.68
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 6.472 / 2.665
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.49 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 134 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.65
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 6.376 / 2.623
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.17 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 135 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.82
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.770 / 16.921 Load End: 7.000 / 2.899
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.24 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 136 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.03
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.54
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 19.813 / 11.151
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 413.81 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 137 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.73
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.39
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 19.195 / 10.506
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 406.57 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 138 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 30.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.51
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.11
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 9.003 / 3.897
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 173.83 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 139 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 41.6
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 147.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.04
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 10.800 / 4.820
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 229.17 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 140 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.55
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.14
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 9.143 / 3.966
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 177.99 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 141 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 5.329 / 2.177
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.83 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 142 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.89
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 7.322 / 3.064
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 159.66 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 143 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.69
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.317 / 13.779 Load End: 5.329 / 2.177
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 148.83 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 144 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 50.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 121.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
7.69
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.94
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 22.321 / 12.938
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 435.25 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 145 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 93.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: < 0.1 Maximum for circuit: 5.00
7.18
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.79
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 21.540 / 12.065
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 426.84 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 146 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 25.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 145.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.98
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.41
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 10.261 / 4.479
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 208.73 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 147 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.4
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.58
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.16
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 8.997 / 3.856
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 171.36 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 148 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 35.7
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 146.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.29
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 11.233 / 4.979
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 238.72 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 149 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.67
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 6.451 / 2.656
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.42 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 150 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.65
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 6.355 / 2.614
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 152.10 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 151 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =8 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 8
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 81.3
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 130.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.82
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 25.485 / 16.598 Load End: 6.975 / 2.888
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 154.16 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 152 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Cable Calculation Report
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 2,431.0
Device Rating In = 3200 Overload Setting Ir = 2720 [Ir >
_ Ib]
Min. Cable Capacity Iz = 805.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,454.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
20.83
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 54.49
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 44.711 / 44.710 Load End: 35.973 / 29.944
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 692.22 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Project: KAFD 3.09 Tx 5 rev 0.p17 Page 153 of 153 Printed on: 14/04/2011
Created using: v17.0.1 (BS7671:2008) - Buro Happold Ltd Copyright © AMTECH Power Software Ltd 2010
Buro Happold
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.52
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.353 / 0.899
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.53
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.369 / 0.909
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 12.5
Device Rating In = 20 Motor Overload Setting Ir = 12.46 [Ir >
_ Ib]
Min. Cable Capacity Iz = 19.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.53
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.384 / 0.919
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 12.5
Device Rating In = 20 Motor Overload Setting Ir = 12.46 [Ir >
_ Ib]
Min. Cable Capacity Iz = 19.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.54
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.400 / 0.929
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 112.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 180.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.57
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.52
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 5.350 / 2.269
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 76.14 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.0
Device Rating In = 50 Motor Overload Setting Ir = 45 [Ir >
_ Ib]
Min. Cable Capacity Iz = 71.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.96
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.499 / 1.635
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 66.29 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 45.0
Device Rating In = 50 Motor Overload Setting Ir = 45 [Ir >
_ Ib]
Min. Cable Capacity Iz = 71.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 100.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.98
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.531 / 1.655
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 67.06 x 103 Adiabatic Limit k²S² (A²s): 5.23 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.63
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.646 / 1.089
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.64
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.668 / 1.103
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.73 [BS 7671, Table 4C4] Subject to Simultaneous Overload
No. of trays = 5 No. of circuits per tray = 4
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 402.6
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 496.0 [BS 7671, Appendix 4.5, Formula (2)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.85
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 13.939 / 8.295
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 651.55 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.49
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.262 / 0.840
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.50
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.285 / 0.854
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.83
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.172 / 1.427
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.51 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.85
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.212 / 1.452
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 59.45 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.51
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.308 / 0.870
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.50
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.285 / 0.854
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.77
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.002 / 1.318
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 54.42 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.73
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 1.896 / 1.250
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.16
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 3.031 / 1.968
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 78.81 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 20 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 16.2
Device Rating In = 20 Motor Overload Setting Ir = 16.15 [Ir >
_ Ib]
Min. Cable Capacity Iz = 25.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.11
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.812 / 11.996 Load End: 2.889 / 1.879
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 75.48 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 140.0
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 472.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
7.94
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 5.38
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 16.999 / 10.971
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 993.68 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 55.0
Device Rating In = 63 Overload Setting Ir = 63 [Ir >
_ Ib]
Min. Cable Capacity Iz = 87.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.33
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.27
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 4.178 / 1.696
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 43.50 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 55.0
Device Rating In = 63 Overload Setting Ir = 63 [Ir >
_ Ib]
Min. Cable Capacity Iz = 87.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.29
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.25
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 4.067 / 1.648
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 42.18 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
No. of trays = 4 No. of circuits per tray = 1
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 648.4
Device Rating In = 1000 Overload Setting Ir = 800 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
7.20
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 46.91
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 17.812 / 11.996
Protective Device Breaking Capacity (kA): Icu: 50 Ics: 37.5
Adiabatic Check: CPD Energy Let-through (A²s): 45.00 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 55.0
Device Rating In = 63 Overload Setting Ir = 63 [Ir >
_ Ib]
Min. Cable Capacity Iz = 87.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.01
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.09
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 3.526 / 1.438
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 36.29 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 55.0
Device Rating In = 63 Overload Setting Ir = 63 [Ir >
_ Ib]
Min. Cable Capacity Iz = 87.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.99
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 1.08
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 3.482 / 1.419
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 35.77 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 172.6
Device Rating In = 200 Overload Setting Ir = 200 [Ir >
_ Ib]
Min. Cable Capacity Iz = 275.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.10
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 2.82
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 9.635 / 4.553
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 267.57 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 24.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 49.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.60
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 1.926 / 0.764
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 17.47 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 214.5
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 342.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 399.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 95 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.28
Adiabatic check (mm 2 ) CPC Section = Separate 95 Total = 95.0 Min. Section = 3.57
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 8.792 / 4.250
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 292.51 x 103 Adiabatic Limit k²S² (A²s): 460.10 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 124.3
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 207.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.93
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 1.94
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 6.442 / 2.847
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 135.07 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.70
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 2.239 / 0.891
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 21.01 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.69
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 2.206 / 0.878
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 20.64 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 5.48 V (User defined)
Design Current Ib = 34.0
Device Rating In = 40 Overload Setting Ir = 40 [Ir >
_ Ib]
Min. Cable Capacity Iz = 54.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
0.64
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 0.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 2.071 / 0.823
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 19.10 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 0.0
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 287.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.06 Maximum for circuit: 5.00
2.30
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 3.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 7.518 / 3.393
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 263.81 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 140.0
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 472.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
4.76
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 3.35
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 11.994 / 6.683
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 408.97 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 80.0
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 189.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.88
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 3.98
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.999 / 10.971 Load End: 15.827 / 9.631
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 399.86 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 40.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 117.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
6.57
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 3.68
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.999 / 10.971 Load End: 15.462 / 9.182
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 370.56 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
5.99
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.49
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.999 / 10.971 Load End: 14.477 / 8.083
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 328.12 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 80.0
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 189.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
4.34
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 3.32
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.994 / 6.683 Load End: 11.342 / 6.128
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 303.53 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.6 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
3.95
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.994 / 6.683 Load End: 10.568 / 5.441
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 219.28 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =3 Cg = 0.82 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 40.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 117.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 192.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 5.00
4.21
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.90
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.994 / 6.683 Load End: 11.130 / 5.933
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 253.58 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Cable CAB-Tx6 Tx 6
Connection From: Tx 6 To: MDB 6
Active Source: Tx 6
Load Type: Main cable to Switchboard Design Current Ib (A): 1,519.4
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,519.4
Device Rating In = 2000 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 474.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
18.69
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 114.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.229 / 29.229 Load End: 26.807 / 24.669
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 270.40 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 472.2
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.96
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 6.13
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.958 / 15.394 Load End: 18.592 / 14.844
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.49 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 514.3
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.74
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.97
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.644 / 14.879 Load End: 18.287 / 14.356
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.61 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =2 Cg = 0.78 [BS 7671, Table 4C5] Subject to Simultaneous Overload
No. of trays = 3 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 986.5
Device Rating In = 1250 Overload Setting Ir = 1250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 460.5 [BS 7671, Appendix 4.5, Formula (2)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
9.73
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 71.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 22.123 / 20.647 Load End: 19.428 / 16.183
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 105.63 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 116.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
7.13
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.65
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 16.720 / 11.534
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 399.95 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.92
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 16.106 / 10.528
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 386.86 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.67
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.428 / 4.181
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 190.84 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 57.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 102.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.22
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.74
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 4.507 / 3.477
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 117.00 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.32
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.97
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 4.707 / 3.630
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 157.83 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.60
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.17
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.294 / 4.078
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 184.68 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.08
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.47
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.946 / 4.603
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 216.17 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.20
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.54
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 6.199 / 4.798
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 227.85 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 57.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 102.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.05
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.63
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 4.152 / 3.206
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 105.06 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.86
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.33
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.494 / 4.256
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 195.36 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.14
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.51
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 6.070 / 4.698
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 221.90 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.86
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.33
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.494 / 4.256
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 195.36 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.96
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.40
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.712 / 4.423
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 205.37 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 57.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 102.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.90
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.55
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 3.848 / 2.973
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 94.82 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.66
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.105 / 3.956
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 177.38 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.91
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.37
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.601 / 4.338
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 200.27 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.66
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.21
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.592 / 14.844 Load End: 5.105 / 3.956
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 177.38 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 116.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.94
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 16.441 / 11.178
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 395.32 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.75
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.55
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 15.839 / 10.221
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 382.87 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.64
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.395 / 4.129
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 187.75 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 57.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 102.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.20
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.72
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 4.484 / 3.442
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 115.43 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.30
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.95
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 4.683 / 3.592
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 155.50 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.57
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 2.15
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.262 / 4.029
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 181.74 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.04
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.906 / 4.540
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 212.42 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.16
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.52
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 6.155 / 4.730
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 223.77 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 57.9
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 102.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 185.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.03
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 4.133 / 3.176
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 103.73 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.82
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.31
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.460 / 4.202
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 192.15 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.10
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.48
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 6.028 / 4.633
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 217.98 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.82
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.31
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.460 / 4.202
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 192.15 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.93
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.38
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.675 / 4.365
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 201.90 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.55
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.13
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 4.902 / 3.778
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 166.70 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.64
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.075 / 3.910
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 174.61 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.88
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.35
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.565 / 4.282
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 196.93 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 17 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 20
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.64
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.19
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.287 / 14.356 Load End: 5.075 / 3.910
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 174.61 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,215.4
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 474.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.14 Maximum for circuit: 5.00
16.28
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 42.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.747 / 23.747 Load End: 22.123 / 20.647
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: Max. disconnection time (s) = (k²S²/I²): 19.04 Actual disconnection time (s) = 0.14
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 514.3
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.56
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 5.85
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.388 / 14.480 Load End: 18.067 / 14.030
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.69 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 569.2
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 621.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.37
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 5.70
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.114 / 14.048 Load End: 17.801 / 13.620
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.63 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 2 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,083.5
Device Rating In = 1250 Overload Setting Ir = 1250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 412.9 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
9.68
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 71.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 21.962 / 20.361 Load End: 19.393 / 16.137
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 105.63 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 116.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.82
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.57
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 16.252 / 10.957
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 392.45 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.63
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.52
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 15.661 / 10.033
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 380.43 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.40
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 6.689 / 5.110
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 246.57 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.02
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.882 / 4.504
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 210.21 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.33
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.62
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 6.540 / 4.998
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 239.88 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.96
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.40
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.765 / 4.416
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 204.94 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.14
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 6.130 / 4.690
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 221.37 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.76
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.27
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.339 / 4.095
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 185.72 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.80
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.30
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.440 / 4.171
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 190.26 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.08
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.47
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 6.003 / 4.595
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 215.68 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.76
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.27
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.339 / 4.095
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 185.72 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 94.9
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 161.1 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.91
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.37
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.653 / 4.331
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 199.87 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 89.5
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 159.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.058 / 3.883
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 172.98 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.85
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.33
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.544 / 4.250
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 194.98 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 15 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 16
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 100.0
Device Rating In = 125 Overload Setting Ir = 125 [Ir >
_ Ib]
Min. Cable Capacity Iz = 162.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 225.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 25 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.62
Adiabatic check (mm 2 ) CPC Section = Separate 25 Total = 25.0 Min. Section = 2.18
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.067 / 14.030 Load End: 5.058 / 3.883
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 172.98 x 103 Adiabatic Limit k²S² (A²s): 51.12 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 116.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.67
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.53
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 16.011 / 10.662
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 388.60 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.49
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.48
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 15.429 / 9.777
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 371.64 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 66.6
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 125.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.44
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.92
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 7.360 / 3.251
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 115.05 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 61.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 124.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.11
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.73
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 6.474 / 2.797
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 91.07 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 63.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 124.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.38
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.89
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 7.197 / 3.165
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 109.93 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 77.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 129.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.32
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.85
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 8.048 / 3.658
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 139.49 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 66.6
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 125.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.07
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.70
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 6.346 / 2.733
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 88.26 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 61.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 124.4 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.83
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.58
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 5.666 / 2.404
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 73.77 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 63.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 124.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.02
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.67
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 6.222 / 2.672
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 85.58 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group = 10 Cg = 0.72 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 12
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 77.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 129.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.01
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 17.801 / 13.620 Load End: 7.157 / 3.173
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 110.38 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.93 [BS 7671, Table 4C5]
No. of ladders = 2 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,215.4
Device Rating In = 1600 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 494.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
15.75
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 91.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 23.747 / 23.747 Load End: 21.962 / 20.361
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 173.06 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 299.6
Device Rating In = 400 Overload Setting Ir = 400 [Ir >
_ Ib]
Min. Cable Capacity Iz = 459.8 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 120 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.38
Adiabatic check (mm 2 ) CPC Section = Separate 120 Total = 120.0 Min. Section = 5.71
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.810 / 14.018 Load End: 18.989 / 13.058
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.09 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 406.3
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
6.12
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 4.42
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.477 / 13.577 Load End: 16.058 / 10.005
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 950.93 x 103 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.88 [BS 7671, Table 4C4]
No. of trays = 1 No. of circuits per tray = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 526.1
Device Rating In = 630 Overload Setting Ir = 630 [Ir >
_ Ib]
Min. Cable Capacity Iz = 411.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 538.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 240 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
8.24
Adiabatic check (mm 2 ) CPC Section = Separate 240 Total = 240.0 Min. Section = 5.60
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 19.314 / 13.366 Load End: 18.913 / 12.910
Protective Device Breaking Capacity (kA): Icu: 45 Ics: 45
Adiabatic Check: CPD Energy Let-through (A²s): 1.50 x 106 Adiabatic Limit k²S² (A²s): 1,177.86 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.45
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 1.171 / 0.773
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.46
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 1.190 / 0.785
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.46
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 1.210 / 0.798
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.47
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 1.231 / 0.812
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 5.6
Device Rating In = 20 Motor Overload Setting Ir = 5.61 [Ir >
_ Ib]
Min. Cable Capacity Iz = 6.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 42.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 4 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 0.40
0.36
Adiabatic check (mm 2 ) CPC Section = Separate 4 Total = 4.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 0.946 / 0.628
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 327.18 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 5.6
Device Rating In = 20 Motor Overload Setting Ir = 5.61 [Ir >
_ Ib]
Min. Cable Capacity Iz = 6.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 42.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 4 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 0.40
0.37
Adiabatic check (mm 2 ) CPC Section = Separate 4 Total = 4.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 0.965 / 0.640
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 327.18 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 5.6
Device Rating In = 20 Motor Overload Setting Ir = 5.61 [Ir >
_ Ib]
Min. Cable Capacity Iz = 6.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 42.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 4 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 0.40
0.38
Adiabatic check (mm 2 ) CPC Section = Separate 4 Total = 4.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 1.005 / 0.666
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 53.00 x 103 Adiabatic Limit k²S² (A²s): 327.18 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 12.5
Device Rating In = 20 Motor Overload Setting Ir = 12.46 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.3 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.82
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.154 / 1.393
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 57.24 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 12.5
Device Rating In = 20 Motor Overload Setting Ir = 12.46 [Ir >
_ Ib]
Min. Cable Capacity Iz = 14.3 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.85
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.221 / 1.434
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.78 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.87
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.291 / 1.477
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 60.40 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.85
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.221 / 1.434
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.78 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 74.5
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.19
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.72
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 6.855 / 2.949
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 93.76 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.85
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.221 / 1.434
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.78 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.87
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.291 / 1.477
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 60.40 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.90
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.366 / 1.523
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 62.13 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 32.2
Device Rating In = 40 Motor Overload Setting Ir = 32.18 [Ir >
_ Ib]
Min. Cable Capacity Iz = 37.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.51
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.73
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 4.038 / 2.513
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 113.32 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 32.2
Device Rating In = 40 Motor Overload Setting Ir = 32.18 [Ir >
_ Ib]
Min. Cable Capacity Iz = 37.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
1.46
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 1.71
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 3.911 / 2.440
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 108.60 x 103 Adiabatic Limit k²S² (A²s): 2.04 x 106
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.85
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.221 / 1.434
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 58.78 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 9.1
Device Rating In = 20 Motor Overload Setting Ir = 9.11 [Ir >
_ Ib]
Min. Cable Capacity Iz = 10.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 54.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 6 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
0.82
Adiabatic check (mm 2 ) CPC Section = Separate 6 Total = 6.0 Min. Section = 1.61
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 2.154 / 1.393
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 57.24 x 103 Adiabatic Limit k²S² (A²s): 736.16 x 103
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 240.1
Device Rating In = 250 Overload Setting Ir = 250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 287.4 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 298.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 50 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.04 Maximum for circuit: 5.00
3.77
Adiabatic check (mm 2 ) CPC Section = Separate 50 Total = 50.0 Min. Section = 3.66
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 16.058 / 10.005 Load End: 11.381 / 5.879
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 373.93 x 103 Adiabatic Limit k²S² (A²s): 184.55 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.87 [BS 7671, Table 4C5]
No. of trays = 1 No. of circuits per tray = 3
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,228.0
Device Rating In = 1250 Overload Setting Ir = 1250 [Ir >
_ Ib]
Min. Cable Capacity Iz = 550.5 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 736.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 300 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
10.64
Adiabatic check (mm 2 ) CPC Section = Separate 300 Total = 300.0 Min. Section = 71.87
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 26.807 / 24.669 Load End: 22.191 / 17.487
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 122.32 x 106 Adiabatic Limit k²S² (A²s): 1,840.41 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 115.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.54
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.50
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 16.777 / 10.112
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 381.46 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.35
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.45
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 16.073 / 9.267
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 352.50 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 66.6
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 125.2 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 7.205 / 3.089
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 105.32 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 61.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 123.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.08
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.71
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 6.473 / 2.736
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 88.40 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 63.4
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 124.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.34
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 7.205 / 3.089
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 105.32 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 77.8
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 128.7 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
2.28
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 1.83
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.989 / 13.058 Load End: 8.083 / 3.559
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 133.52 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 20.0
Device Rating In = 100 Overload Setting Ir = 100 [Ir >
_ Ib]
Min. Cable Capacity Iz = 115.9 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 158.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.45
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.47
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 16.702 / 10.000
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 380.00 x 103 Adiabatic Limit k²S² (A²s): 25.05 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 10.0
Device Rating In = 80 Overload Setting Ir = 80 [Ir >
_ Ib]
Min. Cable Capacity Iz = 92.3 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 127.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 16 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
6.26
Adiabatic check (mm 2 ) CPC Section = Separate 16 Total = 16.0 Min. Section = 3.43
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 15.999 / 9.167
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 348.77 x 103 Adiabatic Limit k²S² (A²s): 12.78 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 123.0
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 205.5 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.68
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 3.04
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 11.320 / 5.593
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 281.68 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 127.6
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 207.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.51
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.95
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 10.906 / 5.321
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 269.44 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 121.0
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 204.8 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.35
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.86
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 10.518 / 5.073
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 258.29 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =6 Cg = 0.73 [BS 7671, Table 4C4] Not Subject to Simultaneous Overload
No. of trays = 1 No. of circuits per tray = 6
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 124.6
Device Rating In = 160 Overload Setting Ir = 160 [Ir >
_ Ib]
Min. Cable Capacity Iz = 206.0 [BS 7671, Appendix 4.5, Formula (3/4)]
Actual Cable Rating It = 246.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 35 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.02 Maximum for circuit: 5.00
3.45
Adiabatic check (mm 2 ) CPC Section = Separate 35 Total = 35.0 Min. Section = 2.92
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 18.913 / 12.910 Load End: 10.774 / 5.236
Protective Device Breaking Capacity (kA): Icu: 36 Ics: 36
Adiabatic Check: CPD Energy Let-through (A²s): 265.61 x 103 Adiabatic Limit k²S² (A²s): 100.20 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 0.97 [BS 7671, Table 4C5]
No. of ladders = 1 No. of circuits per ladder = 2
3rd Harmonics (%) = 0.00 Ch = 1.00
CPD and Installation Factor Cc = 1.00 [Factor: 0.725 for CPD type BS 30365; 0.9 for Installation Methods 70-73]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Design Current Ib = 1,519.4
Device Rating In = 2000 Overload Setting Ir = 1600 [Ir >
_ Ib]
Min. Cable Capacity Iz = 474.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 1,151.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 630 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.03 Maximum for circuit: 5.00
18.69
Adiabatic check (mm 2 ) CPC Section = Separate 630 Total = 630.0 Min. Section = 114.99
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 29.229 / 29.229 Load End: 26.807 / 24.669
Protective Device Breaking Capacity (kA): Icu: 65 Ics: 65
Adiabatic Check: CPD Energy Let-through (A²s): 270.40 x 106 Adiabatic Limit k²S² (A²s): 8,116.21 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 20.0
Device Rating In = 20 Overload Setting Ir = N/A [Ir >
_ Ib]
Min. Cable Capacity Iz = 23.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.11
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 0.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 10.774 / 5.236 Load End: 3.112 / 1.242
Protective Device Breaking Capacity (kA): Icu: 15 Ics: 7.5
Adiabatic Check: CPD Energy Let-through (A²s): 7,000.00 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 20.0
Device Rating In = 20 Overload Setting Ir = N/A [Ir >
_ Ib]
Min. Cable Capacity Iz = 23.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.10
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 0.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 10.518 / 5.073 Load End: 3.088 / 1.232
Protective Device Breaking Capacity (kA): Icu: 15 Ics: 7.5
Adiabatic Check: CPD Energy Let-through (A²s): 7,000.00 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 20.0
Device Rating In = 20 Overload Setting Ir = N/A [Ir >
_ Ib]
Min. Cable Capacity Iz = 23.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.11
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 0.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 10.906 / 5.321 Load End: 3.124 / 1.246
Protective Device Breaking Capacity (kA): Icu: 15 Ics: 7.5
Adiabatic Check: CPD Energy Let-through (A²s): 7,000.00 Adiabatic Limit k²S² (A²s): 2.04 x 106
Comments
Rating Factors
Air Temperature(°C) = 45.0 Ca = 0.87 [BS 7671, Table 4B1]
Circuits In Group =1 Cg = 1.00 [BS 7671, Table 4C4]
Cable sizing (A) Sized For: Phase Current Carrying Capacity Auto-sized for current-carrying capacity and voltage drop limits.
Voltage drop limit = 8.76 V (User defined)
Design Current Ib = 20.0
Device Rating In = 20 Overload Setting Ir = N/A [Ir >
_ Ib]
Min. Cable Capacity Iz = 23.0 [BS 7671, Appendix 4.5, Formula (1)]
Actual Cable Rating It = 75.0 [It >
_ Iz]
Earth Fault Circuit Protective Conductor (CPC) (mm²): Separate 10 [f] [a] = Auto, [f] = Fixed
Disconnection time (s): From characteristic: 0.01 Maximum for circuit: 0.40
1.13
Adiabatic check (mm 2 ) CPC Section = Separate 10 Total = 10.0 Min. Section = 0.59
Phase Fault
Phase Fault Current Max./Min. (kA): Source End: 11.320 / 5.593 Load End: 3.161 / 1.261
Protective Device Breaking Capacity (kA): Icu: 15 Ics: 7.5
Adiabatic Check: CPD Energy Let-through (A²s): 7,000.00 Adiabatic Limit k²S² (A²s): 2.04 x 106
Operator
Telephone
Fax
e-Mail
13.76 m
12.64
11.64
9.95
160 9.24
160 160 120 8.45
7.47
120
160
120 6.12
120 160 5.45
160
160 4.45
160
120 3.30
160
0.70
0.00
0.00 4.87 6.31 7.64 9.02 10.86 13.55 m
Height of Room: 2.300 m, Mounting Height: 2.410 m, Maintenance factor: Values in Lux, Scale 1:177
0.80
Workplane:
Height: 0.000 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.354, Ceiling / Working Plane: 0.167.
Specific connected load: 4.13 W/m² = 3.29 W/m²/100 lx (Ground area: 93.49 m²)
Page 1
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
14.06 m
13.05
10.89
10.11
8.30
120
6.77
6.10
120 5.31
150
4.57
120
120 2.98
150 1.98
0.70
0.00
0.00 1.60 4.02 5.36 6.72 8.54 11.50 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:181
Workplane:
Height: 0.000 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.376, Ceiling / Working Plane: 0.178.
Specific connected load: 5.77 W/m² = 4.76 W/m²/100 lx (Ground area: 52.24 m²)
Page 2
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
7.64 m
6.93
120
120
130 5.61
130
130 130
130
120
130 130
120 130
130 130 2.06
0.71
0.00
0.00 2.30 4.72 7.03 m
Height of Room: 2.300 m, Mounting Height: 2.500 m, Maintenance factor: Values in Lux, Scale 1:99
0.80
Workplane:
Height: 0.000 m
Grid: 32 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.227, Ceiling / Working Plane: 0.129.
Specific connected load: 3.78 W/m² = 3.09 W/m²/100 lx (Ground area: 22.61 m²)
Page 3
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
14.12 m
13.43
150
120 120 11.65
120 120
150 8.63
120
7.96
150
7.30
120 6.59
180 5.90
150
5.01
4.11
1.51
0.70
0.00
0.00 1.98 7.36 8.80 10.77 12.71 14.74 18.76 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:182
Workplane:
Height: 0.000 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.362, Ceiling / Working Plane: 0.173.
Specific connected load: 5.45 W/m² = 4.24 W/m²/100 lx (Ground area: 71.24 m²)
Page 4
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
Staircases / Summary
6.63 m
5.92
5.33
80
4.89
4.55
60
20
40
20
20 1.76
0.71
0.00
0.00 0.70 1.84 2.67 4.13 5.39 6.09 m
Height of Room: 7.000 m, Maintenance factor: 0.50 Values in Lux, Scale 1:86
Workplane:
Height: 0.000 m
Grid: 32 x 16 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.827, Ceiling / Working Plane: 0.776.
Specific connected load: 9.09 W/m² = 28.13 W/m²/100 lx (Ground area: 16.83 m²)
Page 5
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
Staircases / 3D Rendering
Page 6
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
10.01.2011
Operator
Telephone
Fax
e-Mail
Page 7
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
107.68 m
100.29
93.86
88.50
83.51
78.39
73.33
68.36
62.82
150 57.70
150
52.53
150
120 150 47.35
42.25
37.07
31.90
26.73
21.43
16.25
120 11.11
5.84
0.00
0.00 10.60 23.03 35.45 47.85 61.87 74.41 86.83 100.11 124.05 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:1383
0.85
Workplane:
Height: 0.000 m
Grid: 128 x 128 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.825, Ceiling / Working Plane: 0.481.
Specific connected load: 2.67 W/m² = 2.12 W/m²/100 lx (Ground area: 4222.99 m²)
Page 1
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
6.76 m
6.05
240
240 270
300 300
240 270 270
240 3.62
210 270 300
300 270 3.13
240 300
270 240
240
240
210
0.70
0.00
0.00 0.70 2.71 4.23 6.24 6.95 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:87
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.678, Ceiling / Working Plane: 0.498.
Specific connected load: 9.24 W/m² = 3.64 W/m²/100 lx (Ground area: 23.16 m²)
Page 6
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
15.86 m
250 12.93
250 11.94
250 250
250 250
250 250
250 9.50
250
0.00
0.00 2.07 4.75 7.57 9.51 12.73 17.29 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:204
0.85
Workplane:
Height: 0.800 m
Grid: 64 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.769, Ceiling / Working Plane: 0.458.
Specific connected load: 6.86 W/m² = 3.02 W/m²/100 lx (Ground area: 124.76 m²)
Page 7
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
6.47 m
150
180
180 180
180 210
150 210 180
150
210 3.15
210
120 180 210 180
210 2.53
150
180 180
180 180
0.00
0.00 2.77 6.16 7.50 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:84
0.85
Workplane:
Height: 0.000 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.856, Ceiling / Working Plane: 0.684.
Specific connected load: 8.45 W/m² = 4.96 W/m²/100 lx (Ground area: 25.31 m²)
Page 8
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
4.49 m
360
0.00
0.00 1.34 3.47 4.81 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:58
0.85
Specific connected load: 16.19 W/m² = 4.28 W/m²/100 lx (Ground area: 9.45 m²)
Page 9
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
2.88 m
270
300
300 300 270
330
330 330 300 270
300
330 1.54
330 300 240
270
300 330 330 1.34
270
330 330
300 330 300
270
300
270
240
0.00
0.00 1.28 1.62 2.89 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:37
0.85
Workplane:
Height: 0.800 m
Grid: 16 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.893, Ceiling / Working Plane: 0.292.
Specific connected load: 18.21 W/m² = 6.23 W/m²/100 lx (Ground area: 4.20 m²)
Page 10
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
3.26 m
240
200
0.00
0.00 1.27 2.08 3.36 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:42
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.830, Ceiling / Working Plane: 0.277.
Specific connected load: 14.17 W/m² = 5.41 W/m²/100 lx (Ground area: 5.40 m²)
Page 11
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
2.85 m
120
140
140
120
140
140
1.66
0.00
0.00 0.99 2.00 2.99 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:37
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.145, Ceiling / Working Plane: 0.377.
Specific connected load: 9.55 W/m² = 7.38 W/m²/100 lx (Ground area: 4.03 m²)
Page 12
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
3.17 m
100
120
140 120
140
140 120
140 100
140
120 140
140
120
0.00
0.00 1.34 1.87 3.21 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:41
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.006, Ceiling / Working Plane: 0.363.
Specific connected load: 7.54 W/m² = 5.98 W/m²/100 lx (Ground area: 5.10 m²)
Page 13
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
5.52 m
240
280
280 280
3.96
240
280
280
320 3.10
280
320 2.59
280
240
1.99
240 280 1.52
280
240
0.00
0.00 2.04 2.90 3.52 5.00 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:71
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.999, Ceiling / Working Plane: 0.830.
Specific connected load: 17.56 W/m² = 6.63 W/m²/100 lx (Ground area: 12.19 m²)
Page 14
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
4.50 m
150
180 180
180
150 180
210 180 2.70
210
180
210 210 180 150
180 1.80
180 180
180
150
150
0.00
0.00 1.26 3.85 5.11 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:58
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.868, Ceiling / Working Plane: 0.415.
Specific connected load: 7.45 W/m² = 4.47 W/m²/100 lx (Ground area: 10.34 m²)
Page 15
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
2.83 m
240
280
0.00
0.00 0.98 2.05 3.02 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:37
0.85
Workplane:
Height: 0.800 m
Grid: 16 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.903, Ceiling / Working Plane: 0.288.
Specific connected load: 18.00 W/m² = 6.33 W/m²/100 lx (Ground area: 4.25 m²)
Page 16
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
3.60 m
200
240
240
280 280
240 280
200 240
2.05
240 280 280 200
320
280 280 240
1.55
200
240
280 280 240
240 200
0.00
0.00 1.44 2.21 3.65 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:47
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.755, Ceiling / Working Plane: 0.269.
Specific connected load: 11.33 W/m² = 4.66 W/m²/100 lx (Ground area: 6.75 m²)
Page 17
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
3.60 m
200
240
240 280
280 240
240 280 200
280 2.05
200 320
280
280 240
240 1.55
280
240
280 280
240 200
240
200
0.00
0.00 1.44 2.21 3.65 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:47
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.753, Ceiling / Working Plane: 0.270.
Specific connected load: 11.33 W/m² = 4.66 W/m²/100 lx (Ground area: 6.75 m²)
Page 18
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
2.21 m
140
160 160
140
160
160 140
140
160
160 1.06
0.00
0.00 0.75 1.64 2.38 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:29
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.346, Ceiling / Working Plane: 0.429.
Specific connected load: 14.80 W/m² = 10.07 W/m²/100 lx (Ground area: 2.60 m²)
Page 19
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
5.22 m
90
120
120
90
120 120
90 2.91
2.56
120
2.16
90 120 1.90
120 90
1.47
90
0.00
0.00 1.78 3.14 3.70 4.40 5.61 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:67
0.85
Workplane:
Height: 0.000 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.019, Ceiling / Working Plane: 1.034.
Specific connected load: 5.82 W/m² = 5.54 W/m²/100 lx (Ground area: 13.15 m²)
Page 21
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
5.37 m
100
120 100
120
3.76
120
120
120
100 120
120 1.61
100
100
0.00
0.00 2.29 4.94 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:69
0.85
Specific connected load: 5.94 W/m² = 5.20 W/m²/100 lx (Ground area: 12.88 m²)
Page 22
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
15.04 m
480 12.97
540
540
540 600
600
600
600
600 540
540
540
420 2.08
0.00
0.00 2.50 10.63 13.23 m
Height of Room: 3.200 m, Mounting Height: 3.200 m, Maintenance factor: Values in Lux, Scale 1:194
0.85
Workplane:
Height: 0.000 m
Grid: 64 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.794, Ceiling / Working Plane: 0.590.
Specific connected load: 21.29 W/m² = 4.16 W/m²/100 lx (Ground area: 55.27 m²)
Page 25
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
9.52 m
8.82
8.13
160 80
7.51
200 200
160
200 200
200
200 200
3.67
200
200 200
120
160 1.91
120
0.53
0.00
0.00 2.72 3.79 5.29 6.33 8.05 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:123
0.85
Workplane:
Height: 0.800 m
Grid: 64 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.759, Ceiling / Working Plane: 0.578.
Specific connected load: 6.79 W/m² = 4.20 W/m²/100 lx (Ground area: 31.53 m²)
Page 26
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
5.06 m
4.56
120
150
120 150
180
150 180 180
3.20
120 150
180 180
150
180 2.24
180 150
180 180
150
150
120
0.00
0.00 2.25 3.13 5.36 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:65
0.85
Workplane:
Height: 0.800 m
Grid: 32 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.836, Ceiling / Working Plane: 0.656.
Specific connected load: 7.53 W/m² = 5.04 W/m²/100 lx (Ground area: 14.21 m²)
Page 28
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
20.18 m
300
300
13.19
240
300
360
360 240 9.79
360 360
8.27
360 7.05
360
3.99
0.00
0.00 7.49 9.47 11.60 16.66 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:260
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.716, Ceiling / Working Plane: 0.305.
Specific connected load: 9.92 W/m² = 3.19 W/m²/100 lx (Ground area: 172.55 m²)
Page 1
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
LV Switchroom 1 / Summary
14.25 m
13.54
0.70
0.00
0.00 4.29 11.69 15.76 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:183
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.638, Ceiling / Working Plane: 0.276.
Specific connected load: 8.39 W/m² = 3.19 W/m²/100 lx (Ground area: 102.01 m²)
Page 2
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
14.58 m
13.89
300 13.07
300
300
300 300 10.48
300 9.15
300
8.04
300 300
300 6.75
300
300
300 5.09
300
240
2.43
0.00
0.00 2.28 9.62 12.69 14.87 16.62 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:188
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 16 Points
Boundary Zone: 0.100 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.727, Ceiling / Working Plane: 0.298.
Specific connected load: 11.81 W/m² = 4.22 W/m²/100 lx (Ground area: 81.52 m²)
Page 3
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
MTR / Summary
6.25 m
5.55
480
480 520
480
520
440
0.70
0.00
0.00 0.70 2.23 4.50 5.95 6.64 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:81
0.80
Workplane:
Height: 1.000 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.682, Ceiling / Working Plane: 0.300.
Specific connected load: 21.09 W/m² = 4.17 W/m²/100 lx (Ground area: 20.30 m²)
Page 4
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
MV Switchroom / Summary
5.17 m
4.46
280
300 280
300
300 280
260
300 2.66
280 280
300 2.42
280 300
280
260
0.70
0.00
0.00 0.70 2.13 3.15 4.53 5.22 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:67
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 16 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.667, Ceiling / Working Plane: 0.246.
Specific connected load: 15.52 W/m² = 5.46 W/m²/100 lx (Ground area: 13.79 m²)
Page 5
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
5.17 m
4.46
260
280 260
280 260
300
280 300 280
260 2.66
300 2.42
260
280
260 280 280
260
0.70
0.00
0.00 0.70 2.13 3.15 4.53 5.22 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:67
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 16 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.701, Ceiling / Working Plane: 0.264.
Specific connected load: 15.52 W/m² = 5.69 W/m²/100 lx (Ground area: 13.79 m²)
Page 6
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
20.74 m
19.39
17.42
300 300 15.84
300 240
300 13.69
240
8.04
240 5.85
300
300 4.36
300
240 2.46
0.00
0.00 2.49 4.86 6.92 9.88 13.37 19.31 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:267
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.592, Ceiling / Working Plane: 0.306.
Specific connected load: 7.70 W/m² = 2.84 W/m²/100 lx (Ground area: 236.23 m²)
Page 7
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
LV Switchroom 2 / Summary
15.08 m
240
300
300
240 300
300 10.72
300
300
240 8.21
300 360
120
360 7.01
300
180 5.88
300 5.06
300 300 4.30
300 300
1.65
0.00
0.00 3.34 4.88 6.55 9.43 13.86 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:194
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.669, Ceiling / Working Plane: 0.308.
Specific connected load: 9.62 W/m² = 3.43 W/m²/100 lx (Ground area: 111.25 m²)
Page 8
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
5.11 m
4.46
180 220
220 3.21
200 2.91
2.56
220 2.06
220 180
0.65
0.00
0.00 0.65 1.29 3.89 5.52 6.10 6.74 7.39 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:66
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.691, Ceiling / Working Plane: 0.224.
Specific connected load: 11.86 W/m² = 5.70 W/m²/100 lx (Ground area: 18.04 m²)
Page 9
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
24.72 m
80
120
120 18.92
120 100
120 17.08
120
13.50
120 12.35
120
120
7.65
120
5.39
120
0.00
0.00 4.49 6.89 9.61 13.00 19.06 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:318
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.705, Ceiling / Working Plane: 0.362.
Specific connected load: 2.96 W/m² = 2.66 W/m²/100 lx (Ground area: 218.75 m²)
Page 10
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
5.99 m
5.29
140 4.55
160 4.00
180
180 180 3.33
180 2.88
180 180
180
0.70
0.00
0.00 0.70 1.55 2.69 3.43 4.07 6.06 6.76 m
Height of Room: 3.000 m, Mounting Height: 3.100 m, Maintenance factor: Values in Lux, Scale 1:77
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.435, Ceiling / Working Plane: 0.185.
Specific connected load: 6.94 W/m² = 4.15 W/m²/100 lx (Ground area: 20.53 m²)
Page 11
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
1.89 m
60 55
65 60
65
1.20
70 70
65 65 60
70
70
65
60
0.69
55 65
65
60
55
0.00
0.00 0.57 1.44 2.02 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:25
0.80
Workplane:
Height: 0.750 m
Grid: 32 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.898, Ceiling / Working Plane: 0.510.
Specific connected load: 12.15 W/m² = 19.77 W/m²/100 lx (Ground area: 1.69 m²)
Page 12
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
Typical WC / Summary
1.60 m
65
65
70 65
70
70
70 0.90
70 65
70
65 70 0.69
70
70 70
65
65
0.00
0.00 0.57 1.09 1.67 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:21
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.033, Ceiling / Working Plane: 0.612.
Specific connected load: 16.06 W/m² = 24.06 W/m²/100 lx (Ground area: 1.28 m²)
Page 13
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
8.70 m
7.89
7.29
6.71
250
150 250
150 5.07
100
100
3.90
100
3.18
2.60
2.18
1.66
0.69
0.00
0.00 1.43 2.53 3.51 4.74 5.59 6.54 8.34 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:112
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.503, Ceiling / Working Plane: 0.217.
Specific connected load: 8.11 W/m² = 7.48 W/m²/100 lx (Ground area: 35.15 m²)
Page 14
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
2.88 m
2.18
65
65
70
65 65 60
70 1.44
65
60 1.16
0.91
0.70
0.00
0.00 0.70 1.58 1.89 2.18 2.74 3.44 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:38
0.80
Workplane:
Height: 0.750 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.426, Ceiling / Working Plane: 0.183.
Specific connected load: 5.56 W/m² = 9.00 W/m²/100 lx (Ground area: 5.12 m²)
Page 15
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
9.11 m
8.40
7.80
7.26
6.20
5.59
5.01
100 4.30
100 100 3.66
100
200 150 2.87
0.70
0.00
0.00 1.22 2.27 5.07 6.18 7.23 8.47 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:117
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.494, Ceiling / Working Plane: 0.210.
Specific connected load: 7.16 W/m² = 7.17 W/m²/100 lx (Ground area: 39.81 m²)
Page 16
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
3.89 m
3.18
2.90
60
2.37
60 60
60 60 60 1.64
50
0.70
0.00
0.00 0.70 1.55 2.07 2.47 3.41 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:50
0.80
Workplane:
Height: 0.750 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.360, Ceiling / Working Plane: 0.158.
Specific connected load: 4.15 W/m² = 7.46 W/m²/100 lx (Ground area: 6.86 m²)
Page 17
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
34.41 m
27.73
24.78
22.86
5.38
2.68
0.00
0.00 4.99 9.63 15.18 26.18 30.64 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:442
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.343, Ceiling / Working Plane: 0.155.
Specific connected load: 5.35 W/m² = 3.31 W/m²/100 lx (Ground area: 112.67 m²)
Page 18
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
28.28 m
23.76
210 210 22.35
21.06
210 210 210 19.65
210
13.55
210
12.09
210 10.10
210 180
210
7.96
150 6.35
0.00
0.00 3.71 6.79 12.87 17.50 21.37 25.72 m
Height of Room: 5.150 m, Mounting Height: 5.150 m, Maintenance factor: Values in Lux, Scale 1:364
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.720, Ceiling / Working Plane: 0.464.
Specific connected load: 5.28 W/m² = 2.73 W/m²/100 lx (Ground area: 344.42 m²)
Page 19
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
3.52 m
180
160 200
180 220
220 220
2.03
220 220
200 200
220 220
1.50
220 160
220
200
1.02
200 180
160
0.28
0.00
0.00 1.05 2.89 3.42 3.94 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:46
0.80
Workplane:
Height: 0.750 m
Grid: 32 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.939, Ceiling / Working Plane: 0.353.
Specific connected load: 16.80 W/m² = 8.78 W/m²/100 lx (Ground area: 6.37 m²)
Page 20
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
3.65 m
2.94
230 220
230 2.34
240
240 240
230
220
1.27
220
0.70
0.00
0.00 0.70 1.51 1.87 2.67 3.36 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:47
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 8 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.852, Ceiling / Working Plane: 0.320.
Specific connected load: 17.67 W/m² = 7.76 W/m²/100 lx (Ground area: 6.06 m²)
Page 21
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
6.94 m
60 6.49
90 5.81
120 5.33
120
4.35
120 150
150
150 120 2.86
120 150
150
2.11
150
120
1.32
0.76
0.00
0.00 2.60 3.56 4.24 4.90 6.37 m
Height of Room: 3.000 m, Mounting Height: 3.000 m, Maintenance factor: Values in Lux, Scale 1:90
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.717, Ceiling / Working Plane: 0.668.
Specific connected load: 3.62 W/m² = 2.97 W/m²/100 lx (Ground area: 21.24 m²)
Page 22
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
14.35 m
120
120
120
8.87
90 150 120
150 8.03
150
150
5.96
120
150 4.51
150 3.43
150
120 1.63
120
0.00
0.00 3.21 6.17 7.62 10.28 12.10 15.55 m
Height of Room: 5.000 m, Mounting Height: 5.000 m, Maintenance factor: Values in Lux, Scale 1:185
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.790, Ceiling / Working Plane: 0.611.
Specific connected load: 5.24 W/m² = 4.45 W/m²/100 lx (Ground area: 102.06 m²)
Page 23
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
11.24 m
10.53
110
120
130 120
130 130 110
130 130 6.81
140
120 140 130
130
120 130 4.82
130
130
120
120
110
0.72
0.00
0.00 4.62 7.70 11.34 m
Height of Room: 5.000 m, Mounting Height: 5.000 m, Maintenance factor: Values in Lux, Scale 1:145
0.50
Workplane:
Height: 0.750 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.863, Ceiling / Working Plane: 0.637.
Specific connected load: 7.56 W/m² = 6.16 W/m²/100 lx (Ground area: 60.72 m²)
Page 24
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
10.01.2011
Operator
Telephone
Fax
e-Mail
4.60 m
3.90
75
80
80
75 2.65
80 80
75 80 1.86
80
75
0.68
0.00
0.00 0.73 1.85 3.22 4.26 4.96 m
Height of Room: 5.000 m, Mounting Height: 5.000 m, Maintenance factor: Values in Lux, Scale 1:60
0.80
Workplane:
Height: 0.750 m
Grid: 32 x 16 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.222, Ceiling / Working Plane: 1.309.
Specific connected load: 7.01 W/m² = 9.04 W/m²/100 lx (Ground area: 10.91 m²)
Page 25
Project 1
10.01.2011
Operator
Telephone
Fax
e-Mail
14.05 m
12.37
550 550
550
550
550 550 550 550
550 550 550
550
550 550
550 1.39
0.00
0.00 18.34 20.49 26.86 33.44 m
Height of Room: 6.100 m, Maintenance factor: 0.80 Values in Lux, Scale 1:240
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.490, Ceiling / Working Plane: 0.223.
Specific connected load: 13.67 W/m² = 5.55 W/m²/100 lx (Ground area: 357.59 m²)
Page 1
KAFD Parcel 3.09 Basement 3 Water Tanks
19.01.2011
Operator
Telephone
Fax
e-Mail
25.60 m
23.61
20.60
18.70
17.00
15.77
12.92
10.97
9.74
6.65
5.42
3.19
1.96
0.00
0.00 2.45 4.85 10.94 18.30 23.24 26.51 31.04 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:329
0.80
Workplane:
Height: 0.000 m
Grid: 64 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.186, Ceiling / Working Plane: 0.706.
Specific connected load: 8.38 W/m² = 4.45 W/m²/100 lx (Ground area: 280.83 m²)
Page 1
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
15.35 m
240
240 280 240
240 240 11.72
240
200 240
9.17
240
7.21
6.00
1.49
0.00
0.00 4.22 7.36 12.42 17.00 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:198
0.50
Workplane:
Height: 0.800 m
Grid: 64 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.112, Ceiling / Working Plane: 0.592.
Specific connected load: 12.76 W/m² = 6.16 W/m²/100 lx (Ground area: 117.38 m²)
Page 1
Level B4
19.01.2011
Operator
Telephone
Fax
e-Mail
17.53 m
240
14.73
240
180
12.45
240 11.61
240
300 9.62
7.96
180
240 180
180 240
3.56
2.23
1.12
0.00
0.00 3.00 5.07 7.04 9.81 13.55 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:226
0.85
Workplane:
Height: 0.800 m
Grid: 64 x 32 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.627, Ceiling / Working Plane: 0.467.
Specific connected load: 6.59 W/m² = 3.32 W/m²/100 lx (Ground area: 81.24 m²)
Page 1
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
70.64 m
320
63.39
59.40
55.84
400 52.54
49.21
44.78
41.52
36.39
32.62
29.39
24.22
18.58
13.87
10.41
6.62
3.39
0.00
0.00 7.17 13.84 23.13 32.02 41.33 50.54 58.72 67.07 75.27 89.36 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:907
0.80
Workplane:
Height: 0.000 m
Grid: 128 x 128 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.964, Ceiling / Working Plane: 0.529.
Specific connected load: 8.63 W/m² = 3.39 W/m²/100 lx (Ground area: 955.08 m²)
Page 1
Buro Happold
Operator
Telephone
Fax
e-Mail
11.93 m
11.22
60 10.12
30
8.30
30 60
30
60 120 6.67
6.12
90 30
5.27
30 4.62
30
3.03
90
1.99
0.71
0.00
0.00 1.62 4.04 5.41 6.61 7.78 9.29 11.52 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:154
Specific connected load: 2.34 W/m² = 4.69 W/m²/100 lx (Ground area: 48.26 m²)
Page 1
3.09 KAFD Core Areas (B1 West) - Emergency
17.01.2011
Operator
Telephone
Fax
e-Mail
15.14 m
14.43
90 13.12
30
11.75
60
9.94
8.99
90 60 60
90 8.28
60
90 60
60 30 6.42
60
30 60
60 30 4.74
60 60
60
60
0.70
0.00
0.00 2.29 4.41 5.91 7.38 10.18 14.05 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:195
Specific connected load: 1.72 W/m² = 3.30 W/m²/100 lx (Ground area: 86.12 m²)
Page 2
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
13.76 m
12.64
11.64
30
9.95
30 90 9.24
8.45
30 90 90 30
30 7.47
30
30 30 60 90
60
30 6.12
90 5.45
30 30
30 30 4.45
90 30
90
3.30
90
30
0.70
0.00
0.00 4.87 6.31 7.64 9.02 10.86 13.55 m
Height of Room: 2.300 m, Mounting Height: 2.410 m, Maintenance factor: Values in Lux, Scale 1:177
0.80
Specific connected load: 1.24 W/m² = 3.51 W/m²/100 lx (Ground area: 93.49 m²)
Page 1
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
14.06 m
13.05
10.89
10.11
30
60 8.30
60
120 6.77
6.10
90
5.31
30
4.57
30
2.98
90
1.98
0.70
0.00
0.00 1.60 4.02 5.36 6.72 8.54 11.50 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:181
Specific connected load: 2.66 W/m² = 4.55 W/m²/100 lx (Ground area: 52.24 m²)
Page 2
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
7.64 m
6.93
90 5.61
90 30
30
30
30
30
90
60 90
2.06
0.71
0.00
0.00 2.30 4.72 7.03 m
Height of Room: 2.300 m, Mounting Height: 2.500 m, Maintenance factor: Values in Lux, Scale 1:99
0.80
Specific connected load: 2.52 W/m² = 3.85 W/m²/100 lx (Ground area: 22.61 m²)
Page 3
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
14.12 m
13.43
30 90 11.65
120
90 30
30 8.63
90
60 90 7.96
7.30
90 30 6.59
30 5.90
30 5.01
60 4.11
60
1.51
0.70
0.00
0.00 1.98 7.36 8.80 10.77 12.71 14.74 18.76 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:182
Specific connected load: 1.95 W/m² = 4.21 W/m²/100 lx (Ground area: 71.24 m²)
Page 4
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
6.63 m
5.92
5.33
4.89
50 4.55
50
50
40
40
30
1.76
0.71
0.00
0.00 0.70 1.84 2.67 4.13 5.39 6.09 m
Height of Room: 7.000 m, Maintenance factor: 0.50 Values in Lux, Scale 1:86
Specific connected load: 9.09 W/m² = 21.85 W/m²/100 lx (Ground area: 16.83 m²)
Page 1
3.09 KAFD Core Areas (B4 - B2 West and B4 - B1 East)
17.01.2011
Operator
Telephone
Fax
e-Mail
Page 2
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
107.68 m
10
10 100.29
10 93.86
10
88.50
10 83.51
10
10 10 78.39
10 10 73.33
68.36
10 10 10
10 10 62.82
20 57.70
10 10
10 52.53
10 10
10 10 47.35
10 10 42.25
10 10 10 37.07
10
10 10 10 31.90
26.73
10 10 21.43
20 16.25
20 11.11
5.84
0.00
0.00 10.60 23.03 35.45 47.85 61.87 74.41 86.83 100.11 124.05 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:1383
0.80
Specific connected load: 0.38 W/m² = 3.09 W/m²/100 lx (Ground area: 4222.99 m²)
Page 1
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
6.76 m
100
100
120
120 120
100 100
140 140 120
140
80 140 3.56
100 120 140
120 100 3.20
140
140
120
100
120 120
100 100
80
0.00
0.00 2.65 4.30 6.95 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:87
0.80
Specific connected load: 9.24 W/m² = 8.44 W/m²/100 lx (Ground area: 23.16 m²)
Page 3
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
15.86 m
12.93
11.94
30
30
60
30 9.50
30 60
60
90 60 30
90
60 90 6.13
60
90 90 5.00
90
90 3.78
90 2.67
90
0.00
0.00 2.07 4.75 7.57 9.51 12.73 17.29 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:204
0.80
Specific connected load: 2.57 W/m² = 5.40 W/m²/100 lx (Ground area: 124.76 m²)
Page 4
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
6.47 m
60
60
80 80
60
80 40
80 80
80 80 60
3.15
60
40
40 60 2.53
60
60
40
0.00
0.00 2.77 6.16 7.50 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:84
0.80
Specific connected load: 4.23 W/m² = 7.92 W/m²/100 lx (Ground area: 25.31 m²)
Page 5
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
4.49 m
100
100
100
40
0.00
0.00 1.34 3.47 4.81 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:58
0.80
Specific connected load: 8.10 W/m² = 9.61 W/m²/100 lx (Ground area: 9.45 m²)
Page 6
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
2.88 m
100
110 100
110 110
110 100
110
120 1.54
110
100 110 1.34
100
110 110
100
110 110
100
0.00
0.00 1.28 1.62 2.89 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:37
0.80
Specific connected load: 18.21 W/m² = 17.21 W/m²/100 lx (Ground area: 4.20 m²)
Page 7
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
3.26 m
90
100
90
110
110 110 100
110
100 110 100 90
90 120 1.72
110 1.54
110 110
90
110 110
100
90 100
0.00
0.00 1.27 2.08 3.36 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:42
0.80
Specific connected load: 14.17 W/m² = 14.09 W/m²/100 lx (Ground area: 5.40 m²)
Page 8
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
3.17 m
40
45
45 40
45 45
40
1.55
40 45
45
40 45
40
0.00
0.00 1.34 1.87 3.21 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:41
0.80
Specific connected load: 7.54 W/m² = 17.65 W/m²/100 lx (Ground area: 5.10 m²)
Page 10
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
5.52 m
40
3.96
40
60
60 3.10
2.59
80 80
1.99
80 80
80 1.52
80
80 80
0.00
0.00 2.04 2.90 3.52 5.00 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:71
0.80
Specific connected load: 8.78 W/m² = 15.17 W/m²/100 lx (Ground area: 12.19 m²)
Page 11
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
2.83 m
90
100
90 100
110
110 110
100
90
110
110 90
100 120 100 1.39
110
110
110 100 90
110
100
90
0.00
0.00 0.98 2.05 3.02 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:37
0.80
Specific connected load: 18.00 W/m² = 17.38 W/m²/100 lx (Ground area: 4.25 m²)
Page 13
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
3.60 m
80
100
100
80
100 100 2.05
100
100
0.00
0.00 1.44 2.21 3.65 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:47
0.80
Specific connected load: 11.33 W/m² = 11.55 W/m²/100 lx (Ground area: 6.75 m²)
Page 14
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
3.60 m
100
100
100
100 2.05
100
80
100 1.55
100
100
100
80
0.00
0.00 1.44 2.21 3.65 m
Height of Room: 3.550 m, Mounting Height: 2.700 m, Maintenance factor: Values in Lux, Scale 1:47
0.80
Specific connected load: 11.33 W/m² = 11.54 W/m²/100 lx (Ground area: 6.75 m²)
Page 15
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
5.22 m
40
60
60
60 40
60
60 2.91
40
2.56
40 60
2.16
60 1.90
60
40 1.47
40
0.00
0.00 1.78 3.14 3.70 4.40 5.61 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:67
0.80
Specific connected load: 5.82 W/m² = 11.65 W/m²/100 lx (Ground area: 13.15 m²)
Page 19
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
5.37 m
40
50
50 40
60
60 50 3.76
60
60
60
60
50 60
40 60 60
50 1.61
40 50
40
0.00
0.00 2.29 4.94 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:69
0.80
Specific connected load: 5.94 W/m² = 11.19 W/m²/100 lx (Ground area: 12.88 m²)
Page 21
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
15.04 m
100
80 12.97
80 80
60
80 80
100 100
100 80
80
80
60
80
80
100
100 2.08
0.00
0.00 2.50 10.63 13.23 m
Height of Room: 3.200 m, Mounting Height: 3.200 m, Maintenance factor: Values in Lux, Scale 1:194
0.80
Specific connected load: 5.81 W/m² = 7.30 W/m²/100 lx (Ground area: 55.27 m²)
Page 25
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
9.52 m
8.82
8.13
7.51
20
40 20
60
60
40
80 80 60
3.67
80 80
60
80
60
60 1.91
60
40
0.53
0.00
0.00 2.72 3.79 5.29 6.33 8.05 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:123
0.80
Specific connected load: 3.39 W/m² = 8.23 W/m²/100 lx (Ground area: 31.53 m²)
Page 26
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
17.53 m
120 90
14.73
90
120
12.45
120 11.61
90
9.62
90 90
90 7.96
90
90
90
90
90
120 3.56
2.23
1.12
0.00
0.00 3.00 5.07 7.04 9.81 13.55 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:226
0.80
Specific connected load: 5.27 W/m² = 5.69 W/m²/100 lx (Ground area: 81.24 m²)
Page 27
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
20.18 m
120 60
60 60
60
60
13.19
30 60
60
60 120 120
30 60 60 90
9.79
90 60
120 60 8.27
60 60 7.05
60
90 60
90 3.99
30
0.00
0.00 7.49 9.47 11.60 16.66 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:260
0.80
Specific connected load: 2.48 W/m² = 4.06 W/m²/100 lx (Ground area: 172.55 m²)
Page 1
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
14.25 m
13.54
120
90 90
120
60 60 30
60
30 30
30 8.42
30 30
30 60 60 30 5.50
30 60
90 120
120
0.70
0.00
0.00 4.29 11.69 15.76 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:183
0.80
Specific connected load: 2.10 W/m² = 4.49 W/m²/100 lx (Ground area: 102.01 m²)
Page 2
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
14.58 m
13.89
13.07
60
60
30
120
60
60 10.48
120
60
60 90 9.15
120
60 120 8.04
60
60 6.75
60 60
5.09
30 90
60
120 90
2.43
90
0.00
0.00 2.28 9.62 12.69 14.87 16.62 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:188
0.80
Specific connected load: 3.94 W/m² = 5.87 W/m²/100 lx (Ground area: 81.52 m²)
Page 3
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
6.25 m
5.55
320
360
360
320 360
320 360
3.37
360 2.76
360 280
360 360
280
280
0.70
0.00
0.00 0.70 2.23 4.50 5.95 6.64 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:81
0.80
Specific connected load: 21.09 W/m² = 6.29 W/m²/100 lx (Ground area: 20.30 m²)
Page 4
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
5.17 m
4.46
120
120
100
120
80
120 100 2.66
120 120 2.42
100 80
100
80
0.70
0.00
0.00 0.70 2.13 3.15 4.53 5.22 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:67
0.80
Specific connected load: 7.76 W/m² = 7.50 W/m²/100 lx (Ground area: 13.79 m²)
Page 5
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
5.17 m
4.46
120
100
120
80
100
120 60 2.66
120 120
2.42
100 80
100
80
60
0.70
0.00
0.00 0.70 2.13 3.15 4.53 5.22 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:67
0.80
Specific connected load: 7.76 W/m² = 7.95 W/m²/100 lx (Ground area: 13.79 m²)
Page 6
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
20.74 m
90 19.39
90 90 17.42
30
30 60 30 15.84
30 30
13.69
30
60 30
60 11.84
120 90 60 90 10.80
60 30 60
60 120
60 90 120
60 8.04
60
60 60 60 60
60 30 5.85
60
60 120
60 4.36
120 60
30 2.46
0.00
0.00 2.49 4.86 6.92 9.88 13.37 19.31 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:267
0.80
Specific connected load: 1.81 W/m² = 3.70 W/m²/100 lx (Ground area: 236.23 m²)
Page 7
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
15.08 m
30
60 30 60
90 60
60 120 10.72
120 60
60 120
90 120 120 60 60
30 8.21
60
60 60
60
7.01
30 30
5.88
60 60 5.06
60 4.30
60 120
60
90 1.65
0.00
0.00 3.34 4.88 6.55 9.43 13.86 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:194
0.80
Specific connected load: 2.89 W/m² = 5.16 W/m²/100 lx (Ground area: 111.25 m²)
Page 8
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
5.11 m
4.46
120
120
120
120 90 3.21
120 2.91
120 90
2.56
60
90 30 2.06
60
0.65
0.00
0.00 0.65 1.29 3.89 5.52 6.10 6.74 7.39 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:66
0.80
Specific connected load: 5.93 W/m² = 7.55 W/m²/100 lx (Ground area: 18.04 m²)
Page 9
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
24.72 m
20
20
20 60 40
18.92
20 40
20 60
17.08
60 20
40
40
20 13.50
20
12.35
20
20
20 40
40 20 7.65
60
5.39
20
0.00
0.00 4.49 6.89 9.61 13.00 19.06 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:318
0.80
Specific connected load: 0.74 W/m² = 3.37 W/m²/100 lx (Ground area: 218.75 m²)
Page 10
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
5.99 m
5.29
4.55
20
80
40 4.00
80 60
40 60
40 80 3.33
40
60
80 2.88
40 60
20
20
0.70
0.00
0.00 0.70 1.55 2.69 3.43 4.07 6.06 6.76 m
Height of Room: 3.000 m, Mounting Height: 3.100 m, Maintenance factor: Values in Lux, Scale 1:77
0.80
Specific connected load: 2.78 W/m² = 6.73 W/m²/100 lx (Ground area: 20.53 m²)
Page 11
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
Typical WC / Summary
1.60 m
65
65
70 65
70
70
70 0.90
70 65
70
65 70 0.69
70
70 70
65
65
0.00
0.00 0.57 1.09 1.67 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:21
0.80
Workplane:
Height: 0.750 m
Grid: 16 x 16 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 1.033, Ceiling / Working Plane: 0.612.
Specific connected load: 16.06 W/m² = 24.06 W/m²/100 lx (Ground area: 1.28 m²)
Page 13
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
8.70 m
7.89
20 7.29
40 6.71
20
20
20 5.07
40 40
40 3.90
40
20 40 3.18
20 2.60
2.18
1.66
0.69
0.00
0.00 1.43 2.53 3.51 4.74 5.59 6.54 8.34 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:112
0.80
Specific connected load: 1.62 W/m² = 7.10 W/m²/100 lx (Ground area: 35.15 m²)
Page 14
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
2.88 m
2.18
50
55 55 50
55
50 45 1.44
55
1.16
45
0.91
0.70
0.00
0.00 0.70 1.58 1.89 2.18 2.74 3.44 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:38
0.80
Specific connected load: 5.56 W/m² = 11.32 W/m²/100 lx (Ground area: 5.12 m²)
Page 15
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
9.11 m
8.40
7.80
40 7.26
20
20 20 6.20
20 5.59
40 40 5.01
20
40 4.30
40
20 3.66
40 40 20
20 2.87
2.21
1.47
0.70
0.00
0.00 1.22 2.27 5.07 6.18 7.23 8.47 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:117
0.80
Specific connected load: 1.43 W/m² = 6.91 W/m²/100 lx (Ground area: 39.81 m²)
Page 16
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
3.89 m
3.18
2.90
50
2.37
50
50
50 50 1.64
40
0.70
0.00
0.00 0.70 1.55 2.07 2.47 3.41 m
Height of Room: 2.800 m, Mounting Height: 2.900 m, Maintenance factor: Values in Lux, Scale 1:50
0.80
Specific connected load: 4.15 W/m² = 9.04 W/m²/100 lx (Ground area: 6.86 m²)
Page 17
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
34.41 m
27.73
24.78
22.86
5.38
40
2.68
0.00
0.00 4.99 9.63 15.18 26.18 30.64 m
Height of Room: 2.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:442
Specific connected load: 1.54 W/m² = 3.63 W/m²/100 lx (Ground area: 112.67 m²)
Page 18
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
28.28 m
20
40 23.76
20 22.35
40 40 21.06
20
20 19.65
20
17.32
20 20
40 13.55
20
40 12.09
40 10.10
40 40
40 7.96
40
20 6.35
0.00
0.00 3.71 6.79 12.87 17.50 21.37 25.72 m
Height of Room: 5.150 m, Mounting Height: 5.150 m, Maintenance factor: Values in Lux, Scale 1:364
0.80
Specific connected load: 0.93 W/m² = 4.15 W/m²/100 lx (Ground area: 344.42 m²)
Page 19
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
3.52 m
100
80
120
100
120
2.03
140
120 120
100
1.50
120
100 1.02
120
80
0.28
0.00
0.00 1.05 2.89 3.42 3.94 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:46
0.80
Specific connected load: 16.80 W/m² = 15.29 W/m²/100 lx (Ground area: 6.37 m²)
Page 20
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
3.65 m
2.94
120
130
2.34
130
140
0.70
0.00
0.00 0.70 1.51 1.87 2.67 3.36 m
Height of Room: 5.000 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:47
0.80
Specific connected load: 17.67 W/m² = 13.74 W/m²/100 lx (Ground area: 6.06 m²)
Page 21
KAFD Parcel 3.09 Basement 1 (Revised Room layouts)
17.01.2011
Operator
Telephone
Fax
e-Mail
6.94 m
6.49
5.81
5.33
80 80
160
80 120 80
160
160 120
2.86
120 160
120
80 80
120 120 40 2.11
80 1.32
80
0.76
0.00
0.00 2.60 3.56 4.24 4.90 6.37 m
Height of Room: 3.000 m, Mounting Height: 3.000 m, Maintenance factor: Values in Lux, Scale 1:90
0.80
Specific connected load: 3.60 W/m² = 4.24 W/m²/100 lx (Ground area: 21.24 m²)
Page 22
Project 1
17.01.2011
Operator
Telephone
Fax
e-Mail
14.05 m
12.37
90 90 10.07
90 90
90 90
90
90 90 90 90
90 90 90 90
90 90
1.39
0.00
0.00 18.34 20.49 26.86 33.44 m
Height of Room: 6.100 m, Maintenance factor: 0.80 Values in Lux, Scale 1:240
Specific connected load: 2.94 W/m² = 18.76 W/m²/100 lx (Ground area: 357.59 m²)
Page 1
KAFD Parcel 3.09 Basement 3 Water Tanks
19.01.2011
Operator
Telephone
Fax
e-Mail
25.60 m
23.61
20.60
80
18.70
17.00
15.77
12.92
10.97
80 9.74
6.65
5.42
3.19
60 1.96
0.00
0.00 2.45 4.85 10.94 18.30 23.24 26.51 31.04 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:329
0.80
Specific connected load: 3.05 W/m² = 6.33 W/m²/100 lx (Ground area: 280.83 m²)
Page 1
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
17.53 m
80
80
60 14.73
80
60 40
40 40 12.45
11.61
40 40 9.62
60
60 7.96
80
80
80 60
40
60
40 40
40 3.56
20 2.23
1.12
0.00
0.00 3.00 5.07 7.04 9.81 13.55 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:226
0.80
Specific connected load: 2.63 W/m² = 5.57 W/m²/100 lx (Ground area: 81.24 m²)
Page 1
Level B4
20.01.2011
Operator
Telephone
Fax
e-Mail
70.64 m
40
63.39
59.40
40
55.84
20 52.54
49.21
44.78
41.52
40
36.39
40 32.62
29.39
24.22
18.58
13.87
10.41
6.62
3.39
0.00
0.00 7.17 13.84 23.13 32.02 41.33 50.54 58.72 67.07 75.27 89.36 m
Height of Room: 3.550 m, Mounting Height: 3.550 m, Maintenance factor: Values in Lux, Scale 1:907
0.80
Specific connected load: 2.13 W/m² = 5.76 W/m²/100 lx (Ground area: 955.08 m²)
Page 2
Buro Happold
Operator
Telephone
Fax
e-Mail
26.68 m
450
450 450 450
450 450 22.09
450 450 450 450 450
18.38
450
450 16.05
450 450 450
450 450 450 450 13.92
900 450 450 450
450 450 10.21
450
450
6.39
2.83
0.00
0.00 17.32 24.56 39.74 46.35 52.58 67.15 m
Height of Room: 6.100 m, Mounting Height: 6.100 m, Maintenance factor: Values in Lux, Scale 1:481
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.173, Ceiling / Working Plane: 0.146.
Specific connected load: 9.46 W/m² = 2.81 W/m²/100 lx (Ground area: 665.78 m²)
Page 1
KAFD Parcel 3.09 Level PGL
21.01.2011
Operator
Telephone
Fax
e-Mail
6.11 m
5.41
4.54
280
360
320 360
360
320 2.97
360 360
320
320
0.70
0.00
0.00 0.70 1.81 3.79 5.41 6.62 7.32 m
Height of Room: 3.000 m, Mounting Height: 3.092 m, Maintenance factor: Values in Lux, Scale 1:79
0.67
Workplane:
Height: 0.750 m
Grid: 32 x 32 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.546, Ceiling / Working Plane: 0.223.
Specific connected load: 11.35 W/m² = 3.59 W/m²/100 lx (Ground area: 21.37 m²)
Page 1
KAFD Parcel 3.09 Level PGL
21.01.2011
Operator
Telephone
Fax
e-Mail
7.11 m
6.42
90 5.86
100
110
110
3.54
110
100 110
110 100 2.65
2.18
100
0.70
0.00
0.00 0.70 2.54 3.40 4.20 5.19 m
Height of Room: 3.000 m, Mounting Height: 3.092 m, Maintenance factor: Values in Lux, Scale 1:92
0.67
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.477, Ceiling / Working Plane: 0.205.
Specific connected load: 9.57 W/m² = 9.44 W/m²/100 lx (Ground area: 17.86 m²)
Page 2
KAFD 3.09 PGL level
21.01.2011
Operator
Telephone
Fax
e-Mail
10.81 m
10.07
9.35
1100
7.13
1100
1100 1.42
0.00
0.00 11.10 12.96 19.28 23.56 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:169
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.335, Ceiling / Working Plane: 0.176.
Specific connected load: 13.40 W/m² = 3.90 W/m²/100 lx (Ground area: 209.87 m²)
Page 1
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
50.21 m
32.03
950 29.35
950
23.81
21.23
950 950 17.96
950
950
950 14.30
950 950
11.26
950 950
950
2.38
0.00
0.00 5.28 14.46 22.41 33.02 38.85 54.96 69.05 83.97 m
Height of Room: 5.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:645
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.242, Ceiling / Working Plane: 0.146.
Specific connected load: 11.90 W/m² = 4.10 W/m²/100 lx (Ground area: 933.07 m²)
Page 2
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
3.19 m
300 2.68
200 250 300 200
250 300 200 200
300
250 250 300 200
250 250 250
200 200 200 300
250 300 250 300
300 250 200
300 250
200 300 300 200 200 250
300 250
250
300 300 200
250 300 150
0.50
0.00
0.00 0.51 7.68 8.18 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:59
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.243, Ceiling / Working Plane: 0.129.
Specific connected load: 7.57 W/m² = 3.11 W/m²/100 lx (Ground area: 25.77 m²)
Page 4
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
19.02 m
17.51
15.13
9.51
1000
1000 7.39
1000
1000
1000 1000 1000 4.64
3.73
1000 1000
1000 1000
1000 1000
0.00
0.00 2.07 8.88 11.77 19.00 22.60 29.10 m
Height of Room: 5.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:245
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.240, Ceiling / Working Plane: 0.144.
Specific connected load: 13.27 W/m² = 3.34 W/m²/100 lx (Ground area: 367.06 m²)
Page 7
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
6.69 m
6.08
450
450
3.76
450
450
450 450 450
2.92
450 450
450
450 450
0.61
0.00
0.00 1.33 12.24 13.49 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:97
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.174, Ceiling / Working Plane: 0.100.
Specific connected load: 10.07 W/m² = 3.79 W/m²/100 lx (Ground area: 44.27 m²)
Page 9
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
3.25 m
0.50
0.00
0.00 15.76 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:113
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.152, Ceiling / Working Plane: 0.092.
Specific connected load: 7.32 W/m² = 2.65 W/m²/100 lx (Ground area: 49.97 m²)
Page 11
KAFD Parcel 3.09 Level 02
21.01.2011
Operator
Telephone
Fax
e-Mail
100.37 m
94.25
88.34
83.30
280
78.56
71.60
61.73
350 57.10
350 51.00
45.11
37.89
30.60
23.49
18.15
12.44
7.27
0.00
0.00 9.81 19.58 31.88 43.67 58.47 70.32 91.13 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:1289
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.556, Ceiling / Working Plane: 0.215.
Specific connected load: 6.57 W/m² = 2.46 W/m²/100 lx (Ground area: 2166.59 m²)
Page 1
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
15.04 m
14.19
13.50
350
350
350
350 420 420 9.93
420 350 8.87
420 420 8.14
350 420
420 7.08
420 6.34
420 420 420 350
280 350
350 350
3.18
280
1.58
0.70
0.00
0.00 2.46 4.15 5.98 8.81 10.98 14.50 18.18 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:194
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.500 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.442, Ceiling / Working Plane: 0.208.
Specific connected load: 10.18 W/m² = 2.90 W/m²/100 lx (Ground area: 147.08 m²)
Page 1
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
LV Switchroom / Summary
15.95 m
210
280
13.17
350 350 12.28
280
11.52
350
280
350 420
280 8.45
7.70
350 350
6.24
210 350 350
350
210
280
0.00
0.00 4.70 6.50 10.05 15.96 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:205
0.80
Workplane:
Height: 0.750 m
Grid: 64 x 64 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.502, Ceiling / Working Plane: 0.222.
Specific connected load: 10.01 W/m² = 3.22 W/m²/100 lx (Ground area: 128.23 m²)
Page 2
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
48.54 m
350 350
350 35.30
32.77
350
350 29.18
350 350 26.74
350
24.37
350 21.92
19.45
350
350
12.35
350 350
350
7.28
280 4.87
0.00
0.00 4.85 9.86 15.94 24.03 30.14 36.31 42.47 49.17 58.19 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:624
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.624, Ceiling / Working Plane: 0.262.
Specific connected load: 9.19 W/m² = 2.94 W/m²/100 lx (Ground area: 826.69 m²)
Page 3
KAFD Parcel 3.09 Level 27
21.01.2011
Operator
Telephone
Fax
e-Mail
46.41 m
210
41.19
38.73
210 350
350 34.94
32.77
29.96
350 27.63
350 350 24.86
350 21.51
350 19.17
280
16.92
280 14.39
11.76
8.77
6.15
0.00
0.00 5.03 10.54 16.04 21.34 27.08 32.50 38.04 43.76 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:596
0.80
Workplane:
Height: 0.750 m
Grid: 128 x 128 Points
Boundary Zone: 0.000 m
Illuminance Quotient (according to LG7): Walls / Working Plane: 0.503, Ceiling / Working Plane: 0.200.
Specific connected load: 6.35 W/m² = 2.31 W/m²/100 lx (Ground area: 1028.46 m²)
Page 1
Buro Happold
Operator
Telephone
Fax
e-Mail
50.21 m
32.03
29.35
23.81
21.23
17.96
14.30
11.26
2.38
0.00
0.00 5.28 14.46 22.41 33.02 38.85 54.96 69.05 83.97 m
Height of Room: 5.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:645
Specific connected load: 2.25 W/m² = 17.97 W/m²/100 lx (Ground area: 933.07 m²)
Page 1
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
3.19 m
50 2.68
150 250 200 150 150 150
200
100 150 150 150
100 100 150 250
250
150 250
100 100 100 100 250
200 150 150
150 100 200 250 200
250
250 150 100 100
150 250 50 50 150
0.50
0.00
0.00 0.51 7.68 8.18 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:59
0.80
Specific connected load: 4.54 W/m² = 3.43 W/m²/100 lx (Ground area: 25.77 m²)
Page 3
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
9.15 m
180 60 8.65
8.09
60 60
180
240 240
180
60 60
0.51
0.00
0.00 3.55 5.54 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:118
0.80
Specific connected load: 2.85 W/m² = 3.44 W/m²/100 lx (Ground area: 27.36 m²)
Page 5
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
19.02 m
17.51
15.13
9.51
80
80 80
7.39
80 80 4.64
3.73
80
80 80 80 80 80
0.00
0.00 2.07 8.88 11.77 19.00 22.60 29.10 m
Height of Room: 5.300 m, Maintenance factor: 0.80 Values in Lux, Scale 1:245
Specific connected load: 2.74 W/m² = 24.00 W/m²/100 lx (Ground area: 367.06 m²)
Page 6
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
6.69 m
6.08
120 60
240 240
60 120 120
120 120
60 120 240 180
60 60 3.76
2.92
0.61
0.00
0.00 1.33 12.24 13.49 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:97
0.80
Specific connected load: 1.76 W/m² = 3.88 W/m²/100 lx (Ground area: 44.27 m²)
Page 8
PGL Lobby
21.01.2011
Operator
Telephone
Fax
e-Mail
3.25 m
120 180 2.67
120 120 60
120 60
240 120 60
180 120
0.50
0.00
0.00 15.76 m
Height of Room: 5.300 m, Mounting Height: 5.300 m, Maintenance factor: Values in Lux, Scale 1:113
0.80
Specific connected load: 1.56 W/m² = 4.02 W/m²/100 lx (Ground area: 49.97 m²)
Page 10
KAFD Parcel 3.09 Level 02
21.01.2011
Operator
Telephone
Fax
e-Mail
100.37 m
40 94.25
88.34
83.30
40 78.56
71.60
80
80 80 61.73
57.10
80 51.00
80 45.11
80 80
40 37.89
80 40
30.60
40 80
23.49
80
18.15
40 12.44
80
80 7.27
0.00
0.00 9.81 19.58 31.88 43.67 58.47 70.32 91.13 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:1289
0.80
Specific connected load: 1.78 W/m² = 3.02 W/m²/100 lx (Ground area: 2166.59 m²)
Page 1
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
15.04 m
14.19
120 13.50
120
120
80
120 120 9.93
40 8.87
80 120 8.14
40
80 120 7.08
40 80 80
6.34
80 120 80 80
80
120 120
120
80 80 120 3.18
1.58
0.70
0.00
0.00 2.46 4.15 5.98 8.81 10.98 14.50 18.18 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:194
0.80
Specific connected load: 2.91 W/m² = 3.75 W/m²/100 lx (Ground area: 147.08 m²)
Page 1
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
15.95 m
30
60
13.17
90
60 12.28
120 90 11.52
60 60
120
30 60 90
90 60 60
60 8.45
90 60 60 7.70
90
120 90
90 90 60
60 90 6.24
60 120 90
60
30 120
60
30
0.00
0.00 4.70 6.50 10.05 15.96 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:205
0.80
Specific connected load: 2.50 W/m² = 3.98 W/m²/100 lx (Ground area: 128.23 m²)
Page 2
KAFD Parcel 3.09 Level 10
21.01.2011
Operator
Telephone
Fax
e-Mail
48.54 m
80
40 42.68
80
80
80
80
35.30
80 32.77
80
80
80 29.18
80 80 26.74
80 80 80
80 120 24.37
80 21.92
80
80 19.45
80 80
40
40
80
80 80 80 12.35
40
40 40
80 40 7.28
4.87
0.00
0.00 4.85 9.86 15.94 24.03 30.14 36.31 42.47 49.17 58.19 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:624
0.80
Specific connected load: 2.33 W/m² = 3.68 W/m²/100 lx (Ground area: 826.69 m²)
Page 3
KAFD Parcel 3.09 Level 27 - Emergency
21.01.2011
Operator
Telephone
Fax
e-Mail
46.41 m
80
80 80 80 41.19
80 38.73
80 80 40 40
80
34.94
40 80 40 40
32.77
80 40 29.96
80
40
40 27.63
120 40 80 24.86
40 40
80 80 21.51
80
40 19.17
40 40 80 80 16.92
40 14.39
40 40 80 11.76
80
8.77
40 40
6.15
0.00
0.00 5.03 10.54 16.04 21.34 27.08 32.50 38.04 43.76 m
Height of Room: 6.400 m, Mounting Height: 3.500 m, Maintenance factor: Values in Lux, Scale 1:596
0.80
Specific connected load: 1.46 W/m² = 2.73 W/m²/100 lx (Ground area: 1028.46 m²)
Page 1
Buro Happold