Professional Documents
Culture Documents
This spreadsheet is generic. It covers both new and existing chillers and constant and
variable flow condenser water scenarios. You will need to customize it for your
particular application by deleting or hiding extraneous rows and worksheets.
General
Option:
Manufacturer:
Model:
Compressor type:
Refrigerant type:
Variable speed drive (Y/N)
Operating Constraints
Maximum CHW flow rate (GPM):
Minimum CHW flow rate (GPM):
Capacity (% of design capacity) below which
hot-gas bypass operates (set to 0 if no HGBP)
Voltage/phase: 480/3
Design Conditions
Evaporator
CHW fouling factor: 0.0001
Leaving CHWST (F):
Entering CHWRT (F):
Design CHW flow (GPM):
CHW pressure drop (ft):
Evaporator passes:
Evap. Refrigerant Temperature (F)
General
Design Conditions
Condenser
CW fouling factor: 0.00025
Entering OAT (F):
ormation:
Full Load Conditions
Complete the "Start Here" worksheet before completing this worksheet. Fill out all yellow-highlighted field
shall be at the proposed design conditions entered above except where noted. The capacity and power in
unmodulated operation (no power or current limits with all capacity control devices fully open). Do not in
capacity or power listed.
Evaporator
Unloading Capacity Power Leaving Temp
% tons kW CHWST (°F)
100% 0
100% 0
100% 0
100% 0
100% 0
100% 5
100% 5
100% 5
100% 5
100% 5
100% 10
100% 10
100% 10
100% 10
100% 10
100% 15
100% 15
100% 15
100% 15
100% 15
100% 20
100% 20
100% 20
100% 20
100% 20
ditions
Evaporator Condenser
Entering Temp CHW flow Entering Temp
CHWRT (°F) gpm OAT (°F)
- -
- -
- -
- -
- Min = -
- -
- -
- -
- -
- Min = -
- -
- -
- -
- -
- Min = -
- -
- -
- -
- -
- Min = -
- -
- -
- -
- -
- Min = -
Part Load Conditions
Complete the "Start Here" worksheet before completing this worksheet. Fill out all yellow-highlighted field
following data shall be at the proposed design conditions entered on the "Start Here" worksheet except w
noted. Do not include ARI tolerance in capacity or power listed. If the calculated capacity is below m
capacity, override this field and enter the minimum capacity.
Evaporator
Percent Capacity Power Exit Entering
of Design tons kW CHWST (°F) CHWRT (°F)
#DIV/0! - 0 0 -
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
Constant OAT
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
With OAT Relief
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
#DIV/0! - 0 #DIV/0!
out all yellow-highlighted fields. The
art Here" worksheet except where
calculated capacity is below minimum
orator Condenser
CHW flow Entering
gpm OAT (°F)
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0
- 0.0