HAY TK100H is suits to many hays 1.1.It is portable, compact, automatic temperature MOISTURE METER moisture content testing, just easy to use and the compensation. as alfalfa, leymus chinensis, moisture measurement 1.5.Measurements are taken orchard grass pennisetum readings are instant. by inserting the sensors hydridum and other Hays. 1.2.Digital display with back into the bale of grains . light gives exact and clearly 1.6.Manual off at any time reading although you stay .Auto power off after 5 at the somber conditions. minutes from last 1.3.It will save time and operation. expense by monitoring dryness and helps to prevent deterioration & decay caused by moisture whilst in storage, therefore ATO-TK100H processing will be more convenient and efficient. 1.4.The moisture meter operates by electrical
2.Specification 3.Panel descriptions
Display:4 digital LCD Measuring range :0-80%(CD00) Operating conditions: 4.Operation procedure Thanks for choosing our Temperature:-10~60°C 3-1 3-6 4.1 Turn on the key ,the moisture meters! Humidity:5%~90%RH 3-2 symbol “0”will be showed Resolusion:0.1 3-3 3-7 on display. It will need For your easy to master this instrument as soon as Accuracy: ± 0.5%n 3-8 zeroing if showed other 3-4 3-9 possible, please read Operating principle: value, please depress 3-5 following instructions E l e c t r i c a l c o n d u c t i v i t y, 3-10 ZE key while the probe carefully and always keep Automatic temperature sensor without touch this meter within easy reach. Compensation anything, or zeroing is Power supply: not efficient. make 4x1.5 AAA size (UM-4) battery zeroing can decrease Dimensions: the effect from the 460×75×35mm 3-1 % symbol 3-5 zero/inc key temperature and 18.3x3x1.4 inch 3-2 low battery 3-6 pin probe humidity in the air. Weight: 3-3 max symbol 3-7 testing value 4.2 Hold the instrument with 203g (not including batteries) 3-4 warning light your hand, insert the probes 3-9 hold/dec key 3-8 power/function 3-10 battery cover key into the materials straightly. needed code. Please refer to will be returned back the 8.Reference Code Table The probes are more the table in 8.0 factory setting, just to CODE Hays deeper, the value is better. say,AL1=13,AL2=18. 4.3 Depress key ,the 5.Warning setting Straw Cd00 symbol “max”will be 5.1 Depressing key and 6.Replace batteries /General showed on display, then don't release until “AL2” When battery symbol 555 the max value must be showed on display(it will showed on display, it must Guinea grass Cd01 stored on display when takes 5 seconds to complete replace the batteries in time. /Clover measuring. Depress the operation),then press key 3- Slide the batteries cover ,put Soap wort Cd02 HO key again, this or 3- to choose your suitable the batteries into the hole function will be canceled. value according to your correctly. Cd03 Wheat Straw 4.4 Choose the suitable need, press key again code for different hays. back to the operation state. 7.Notes: Please choose the code Depress the key and 5.2 Setting the “AL1” just the Please take out the batteries if according to your true not release until the same ways as “AL2”. the instruments without use for conditions, and the default “CDXX” showed on 5.3 Usually ,“AL2”must larger a long time. code is CD00. display, then press 3-5 or than “AL1”,if the “AL2” less Put the probe in the air without 3- key to choose your than “AL1” during setting touch anything when zeroing, process, then the instrument or the zeroing is not efficient.