Professional Documents
Culture Documents
10 Plywood Sheets
Product Information Overview on the Germ. Market
18.10 Schalungsplatten
PI 261 E 1 - 8 Übersicht auf deutschem Markt
Overview of the most common plywood sheets available on the German market
The information provided is subject to fluctuations in the market and further development of each
product.
Flexural stress and The values were adopted from or determined based on the manufacturer´s
modulus of elasticity information. These correspond predominantly to a manufacturing moisture
content of 7 % to 9 % and the ultimate flexural stress. As a rule, standard
deviations have been taken into consideration.
The table values have been converted and refer to a wood moisture content of 20 % according to the
recommendations of the German Quality Protection Association for Concrete Formwork. For this, cor-
rection factors taken from the Finnforest plywood handbook were used.
Note: the given values are empirical which are to be regarded as average values. As timber products
are subject to strong natural fluctuations, the specific plywood sheet values of the respective manufac-
turer as well as the conditions on the construction site, handling and maintenance etc. are also to be
taken into consideration. In addition, the structure of some sheets (e.g. type and thickness of veneer)
can change which could result in different statical values.
If no specific details are available, the values indicated in the table can be used for roughly estimated
calculations. For a proven different wood moisture content in the plywood working conditions, the table
values can be corrected using the following factors.
Flexural stress: 15 % wood moisture content = correction factor approx. 1.14 (birch) 1.08 (spruce)
27 % wood moisture content = correction factor approx. 0.80 (birch) 0.87 (spruce)
The flexural strength σbieg is given in Value II (= long) and ⊥ (= transverse) grain direction of the face
veneer. A safety factor of 2.33 has been taken into consideration for the ultimate flexural stress.
The modulus of elasticity is given in Value II (= long) and ⊥ (= transverse) grain direction of the face
veneer.
No. Name Description/Structure Item no. Surface/ Thickness Size Size Weight Flexural Flexural Modulus Modulus Remarks on utilisation
Surface Coating [mm] Length Width stress stress of of
[cm] [cm] [kg/m²] long trans- elasticity elasticity
[N/mm²] verse long trans.
[N/mm²] [N/mm²] [N/mm²]
1.5 Arauco pine Veneered plywood 052837 Sanded surface, 21 250 125 11.3 Values published by manufacturer First-class processed formwork and gen-
Chilean pine plywood uncoated/natural are determined only according to DIN eral-purpose plywood, for concrete surfaces
2
) 9-ply EN 310 with normal requirements up to approx. 3
weather and boilproof bonding uses,
(BFU 100), Quality C+/C concrete surface with wood finish
1 1 1 1
1.6 Lake pine Veneered plywood 052800 Sanded surface, 20.5 250 125 11.0 ) ) ) ) Simple, uncoated formwork plywood, used
Brazilian pine plywood uncoated/natural with slab formwork for concrete surfaces
7-ply with minimum requirements up to approx. 3
weather and boilproof bonding uses,
Quality C+/C concrete surface with wood finish
1) 2
No details possible due to strong fluctuations ) Currently not included in the PERI programme
No. Name Description/Structure Item no. Surface/ Thickness Size Size Weight Flexural Flexural Modulus Modulus Remarks on utilisation
Surface Coating [mm] Length Width stress stress of of
[cm] [cm] [kg/m²] long trans- elasticity elasticity
[N/mm²] verse long trans.
[N/mm²] [N/mm²] [N/mm²]
1.8 3-ply plywood 3- ply plywood - coated 050070 Sanded surface and 21 150 50 10.5 13,8 2,5 9450 736Plywood sheets for wall and slab areas,
(yellow/red) without steel protection profile 050080 melamine resin coating 21 200 50 for concrete surfaces with high require-
(with steel protection profile on 050000 21 250 50 Values according approval Z-9.1-401 ments, approx. 10 – 30 uses
request) concrete surface with slight timber finish
Bonding EN 314-2 Nkl. 3
(BFU 100), edges coated with
melamine resin
1.9 PERI Spruce Veneered plywood 052830 Phenolic resin coating 21 250 125 10.9 8,0 6,0 6450 3920 Plywood sheets for concrete surfaces with
Finnish coniferous wood 052831 on both sides 21 250 50 high requirements, approx. 15 – 25 uses,
11-ply coated 120 g/m² mainly used in slab areas,
Bonding EN 314-2 Nkl. 3 slight timber structure possible
(BFU 100), edge protective
coating
1 1 1 1
1.10 Plastform Veneered plywood Phenolic resin coating 21 250 125 12.6 ) ) ) ) Plywood sheets for concrete surfaces with
(Brazil) Combi-plywood, 9-ply on both sides ±1 standard requirements, approx. 10 uses,
hardwood top layers, pine middle 120 g/m² mainly used in slab and residual areas
2
) layers, coated,
weather and boilproof,
edge protective coating
1.11 Chinese coated Veneered plywood 052622 Phenolic resin coating 21 125 250 12.0 19,5 10,2 7560 3820 Plywood sheets for concrete surfaces with
plywood Chinese poplar plywood, 13-ply on both sides 27 250 62.5 standard requirements, approx. 10 uses,
Values determined by individual
(poplar) coated 120 g/m² mainly used in slab and filler areas
testing, statistically not assured
weather and boilproof,
edge protective coating
1.12 PERI Ecoform Veneered plywood 050080 Phenolic resin coating 21 250 125 10.9 7,6 4,7 6820 3140 Plywood sheets for concrete surfaces with
Finnish coniferous wood on both sides standard requirements, approx. 15 – 20
2
) 7-ply coated 120 g/m² uses, mainly used in slab, residual and filler
Bonding EN 314-2 Nkl. 3 areas , slight timber structure, slight crack
(BFU 100), edge protective formation in coating and face veneer possi-
coating ble
1) 2
No details possible due to strong fluctuations ) Currently not included in the PERI programme
No. Name Description/Structure Item no. Surface/ Thickness Size Size Weight Flexural Flexural Modulus Modulus Remarks on utilisation
Surface Coating [mm] Length Width stress stress of of
[cm] [cm] [kg/m²] long trans- elasticity elasticity
[N/mm²] verse long trans.
[N/mm²] [N/mm²] [N/mm²]
1.13 Wisa Form Veneered plywood Phenolic resin coating 21 250 125 10.6 7,6 4,7 6820 3140 Plywood sheets for concrete surfaces with
Spruce Finnish coniferous wood on both sides standard requirements, approx. 15 – 20
7-ply coated 300 g/m² uses,
2
) Bonding EN 314-2 Nkl. 3 mainly used in slab, residual and filler areas
(BFU 100), edge protective
coating
1 1 1 1
1.14 AS Ply Veneered plywood 052620 Phenolic resin coating 21 250 125 14.9 ) ) ) ) Plywood sheets for concrete surfaces with
Asian on both sides standard requirements, approx. 15 – 25
2
) 11-ply 120 g/m² uses,
different timber structure mainly used in slab, residual and filler areas
weather and boilproof bonding, , slight structuring possible
edge protective coating
1.15 PERI Beto Veneered plywood sheet 052821 Phenolic resin coating 21 125 250 11.9 13,8 6,9 8180 4710 Plywood sheets for concrete surfaces with
Finnish Combi-Mirror sheet 052824 on both sides 21 62.5 250 11.9 standard requirements, approx. 15 – 30
11-ply 052822 120 g/m² 21 150 300 11.9 uses,
Birch face veneers mainly used in slab areas
Birch/coniferous middle layers Concrete surface basically without structure
Bonding EN 314-2 Nkl. 3
(BFU 100), edge protective
coating
1.16 PERI Birch Veneered plywood sheet 052820 Phenolic resin coating 21 125 250 14.25 13,3 11,5 8080 6270 Plywood sheets for concrete surfaces with
Birch throughout on both sides standard requirements, approx. 20 – 50
15-ply 120 g/m² uses,
Bonding EN 314-2 Nkl. 3 used for walls, column and slab areas,
(BFU 100), edge protective even concrete surface without structure
coating
1) 2
No details possible due to strong fluctuations ) Currently not included in the PERI programme
No. Name Description/Structure Item no. Surface/ Thickness Size Size Weight Flexural Flexural Modulus Modulus Remarks on utilisation
Surface Coating [mm] Length Width stress stress of of
[cm] [cm] [kg/m²] long trans- elasticity elasticity
[N/mm²] verse long trans.
[N/mm²] [N/mm²] [N/mm²]
1.17 Fin-Ply Veneered plywood sheet 052260 Phenolic resin coating 21 125 250 14.25 13,3 11,5 8080 6270 Plywood sheets for concrete surfaces with
Birch throughout 052060 on both sides 21 150 250 high requirements, approx. 30 – 70 uses,
15-ply 052270 240 g/m² 21 150 300 Used for walls, column and slab areas,
Bonding EN 314-2 Nkl. 3 052070 21 150 400 even concrete surface without structure
(BFU 100), edge protective
coating
1.18 Fin-Ply-Maxi Veneered plywood sheet 052823 400 g/m² 20 750 270 13.5 13,3 11,5 8080 6270 as 1.17, however joint-free surfaces
Birch throughout 052829 240 g/m² 20 540 200
15-ply Phenolic resin coating
as 1.17 on both sides
1.19 PERI Beto S Veneered plywood sheet 1 side coated 21 1.25 2.5 11.9 13,8 6,9 8180 4710 Plywood sheets for wall and slab areas,
Finnish Combi-Mirror sheet slightly absorbant (MDO) used for concrete surfaces without structure
11-ply 1 side coated with Slightly absorbant = matt concrete surfaces,
Birch face veneers, phenolic resin reduced proportion of pores
Birch/coniferous middle layers 120 g/m² Treat with release agent before use!
Bonding EN 314-2 Nkl. 3 Approx. 15 uses
(BFU 100), edge protective
coating
No. Name Description/Structure Item no. Surface / Thickness Size Size Weight Flexural Flexural Mod. of Mod. of Remarks on utilisation
Surface Coating [mm] Length Width stress stress elasticity elasticity
[cm] [cm] [kg/m²] long trans. long trans.
[N/mm²] [N/mm²] [N/mm²] [N/mm²]
2.1 3-ply large-area 3-ply sheeting Sanded; 21 600 150 11,0 13,8 2,5 9450 740 Plywood sheets used for wall and slab
plywood sheet 3-ply cross-bonded coated with melamine (27) 500 100 areas, for concrete surfaces with standard
sanded resin or uncoated/natural 400 (14,2) requirements approx. 1 – 30 uses,
coniferous wood 300 concrete finish with slight timber structure
Bonding EN 314-2 Nkl. 3 250
(BFU 100)
No. Name Description/Structure Item no. Surface / Thickness Size Size Weight Flexural Flexural Mod. of Mod. of Remarks on utilisation
Surface Coating [mm] Length Width stress stress elasticity elasticity
[cm] [cm] [kg/m²] long trans. long trans.
[N/mm²] [N/mm²] [N/mm²] [N/mm²]
2.2 3-ply large-area 3-ply sheeting Brushed surface, 21 600 150 11,0 13,8 2,5 9450 740 Plywood sheets used for wall and slab
structured ply- 3-ply cross bonded sanded rear side; (27) 500 125 (14,2) areas, for concrete surfaces with standard
wood sheet coniferous wood coated with melamine 400 100 requirements approx. 1 – 30 uses,
Bonding EN 314-2 Nkl. 3 resin or uncoated/natural timber structure is strongly pronounced
(BFU 100) with/without V-groove corresponding to the amount of brushing
treatments
No. Name Description/Structure Item no. Surface / Thick- Size Size Weight Flexural Flexural Mod. of Mod. of Remarks on utilisation
Surface Coating ness Length Width stress stress elasticity elasticity
[mm] [cm] [cm] [kg/m²] long trans. long trans.
[N/mm²] [N/mm²] [N/mm²] [N/mm²]
3.1 BETOPLAN Veneered plywood 140 g/m² 4 250 125 2.5 Facing plywood for straight and curved
4 mm 3-ply 300 125 concrete surfaces with high requirements,
Edges: brown (coating) approx. 10 – 20 uses
Bonding: EN 314-2 Nkl. 3, (BFU
100)
No. Name Description/Structure Item no. Surface / Thick- Size Size Weight Flexural Flexural Mod. of Mod. of Remarks on utilisation
Surface Coating ness Length Width stress stress elasticity elasticity
[mm] [cm] [cm] [kg/m²] long trans. long trans.
[N/mm²] [N/mm²] [N/mm²] [N/mm²]
3.3 BETOPLAN top Veneered plywood Phenolic resin coating 21.5 300 200 13.5 17,8 19,8 4260 5410 For joint-free concrete surfaces with higher
9 or 11-ply on both sides 550 g/m² 400 200 requirements,
Edges: grey (coating) with non-woven fabric 520 200 concrete finish without structure,
Bonding: EN 314-2 Nkl. 3, (BFU approx. 40 uses,
100) other sizes on request
3.4 BETOPLAN S Veneered plywood Coated plywood 21 520 200 13,5 13,8 17,5 4260 5410 Concrete formwork for higher requirements,
7 or 9-ply slightly absorbant 9 300 200 6 21,7 18,5 5740 4510 slightly absorbant plywood = darker, matt
Edges: clear (coating) finish and concrete surfaces with low a-
Bonding: EN 314-2 Nkl. 3, (BFU Values according to DIN EN 310. Not mount of pores,
100) valid for design up to approx. 20 uses
3.5 WESTOPLAN Veneered plywood GRP + Gelcoat coating 20 650 250 12,4 19,8 17,8 5410 4260 Large-area, few plywood joints, concrete
XXL 7 - 9-ply surfaces with higher requirements
Bonding: EN 314-2 Nkl. 3, (BFU Values according to DIN EN 310. Not
100) valid for design
3.6 WESTAG RS Chipboard Treated with release 10 543 205 10,0 9,4 9,8 3440 3360 For concrete surface with low amount of
spezial (geölt) 5 layers, highly compressed, agent 271 pores, high surface strength, few numbers
treated with release agent, 21 543 205 16,8 8,7 9,4 3530 3690 of use
quality according DIN EN 312:
Values according to DIN EN 310. Not
P5
valid for design
3.7 WESTASPAN Chipborad with phenolic resin Phenolic resin with fibre 21 520 200 15.5 12,8 10,8 4100 3530 Smooth concrete surface, few plywood
450 SP and fibre mat mat 450 g/m² joints, standard requirements
Values according to DIN EN 310. Not
quality according DIN EN 312:
valid for design
P5
3.8 WESTAG Phe- Chipboard with phenolic resin Phenolic resin 21 540 200 16,5 10,1 10,1 3690 3690 Smooth concrete surface, standard re-
nox spezial overlay 200 g/m² or quirements
Values according to DIN EN 310. Not
200/360 quality according DIN EN 312: 360 g/m²
valid for design
P5
3.9 MAGNOPLY Chipboard with 2mm face ve- Phenolic coating 260 21 200 520 15,9 17,2 10,4 4590 3280 Smooth concrete surface, standard re-
260 SP neer on each side, phenolic g/m² quirements
resin overlay
No. Name Description/Structure Item no. Surface / Thick- Size Size Weight Flexural Flexural Mod. of Mod. of Remarks on utilisation
Surface Coating ness Length Width stress stress elasticity elasticity
[mm] [cm] [cm] [kg/m²] long trans. long trans.
[N/mm²] [N/mm²] [N/mm²] [N/mm²]
Values for 20 % moisture content
5.1 MULTIPLEX Plywood, birch or other hard- Phenolic resin 450 g/m² 21 200 540 14,8 12,4 13,8 4260 4075 Smooth concrete surface, few plywood
450 wood, bonding EN 314-2 Nkl. 3 200 600 joints, standard requirements
(BFU 100), sealed edges
5.2 MULTIPLEX Plywood, one-side silk screen Silk screen side, 21 200 540 14,8 14,8 21,9 7720 7000 Concrete surface with silk screen texture
sieb surface , bonding EN 314-2 phenolic resin 450 g/m², 200 600
Nkl. 3 (BFU 100), sealed edges 130 g/m² on the back
5.3 MULTIPLEX Coated plywood, TOP with plastic coating 21 150 540 14,8 values on request Concrete surface with high architectural
TOP/CPL bonding EN 314-2 Nkl. 3 or CPL coating 200 540 finish requirements, high amount of plywood
(BFU 100), sealed edges uses
5.4 SPANFORM Chipboard with film overlay, Phenolic resin 130 g/m² 18 200 540 15,6 7,7 8,4 3890 4280 Economical plywood for standard applica-
bonding AW DIN 68705 21 - - - - tion