Professional Documents
Culture Documents
ED-94040E
)4/
\ &&-‘/,L ,(- :-,, <’ ‘. h .%’2
SHARP ISSUE March 5, 1998
PAGE 14 Pages
APPROVED BY: DATE: ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION REPRESENTAm DMSION
- ,. I- 1 -. ,dC,
A 1 lUi\1 OPTO-ELECTRONIC DEVICES Dn!
I
PHOTOCOUPLER
MODEL No.
PC123
1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
ill This product is designed for use in the following application areas :
1
* OA equipment * Audio visual equipment * Home appliances
* Telecommunication equipment (Terminal) * Measuring equipment
+ Computers
[ * Tooling machines
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (31, please be sure to observe the precautions given in those respective paragraphs.
(21 Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
1
. Transportation control and safety equipment (aircraft, train, automobile etc.1
- Trafhc signals * Gas leakage sensor breakers . Rescue and security equipment
[ * Other safety equipment
(31 Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as :
[
. Space equipment
* Nuclear power
. Telecommunication
control equipment *
equipment (for trunk lines)
Medical equipment
. Please contact and consult with a Sharp sales representative for any questions about this product.
DATE
CUSTOMER’S APPROVAL PRESENTED
BY
T. Matsumura,
DATE Department General Manager of
Engineering Dept.,11
Opto-Electronic Devices Div.
BY ELECOM Group
SHARP CORPORATION
SHARP CORPORATION ED-94040E 1 March 5, 1998
MODEL No. 1 PAGE
PC 123 l/8
I
1. Application
2. Outline
4. Reliability
5. Incoming inspection
6. Supplement
(1 I Short between anode to cathode on the primary side and between collector
to emitter on the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shall be used.
Specific brominated flame retardants such as the PBBO, and PBB, are not used
in this device at all.
7. Notes
2. Outline
Rank mark
mark l2
1: Anode 3: Emitter
2: Cathode 4: Collector
7.62’0-3 4. 58 ‘0.3
*4 For 10s
SHARP CORPORATION ED-94040E 1 March 5, 1998
MODEL No. PAGE
PC 123 5/B
g 80
2 70
3 60
4
35 40
&
$ 2o
5 0
-30 0 25 55 75 100 125 -30 0 25 55 75 100 125
200
150
100
50
0
r
-30 0 25 50 75 100 125 -30 0 25 50 75 100 125
4. Reliability
5. Incoming inspection
(2) Appearance
1 For cleaning
In case when the other solvent is used, there are cases that
the packaging resin is eroded. Please use the other solvent
after thorough confirmation is performed in actual using condition.
2. The LED used in the Photocoupler generally decreases the light emission power
by operation. In case of long operation time, please design the circuit with considering
the degradation of the light emission power of the LED. (50%/5yearsl
SHARP CORPORATION ED-94040E 1 March 5, 1998
MODEL No. PAGE
PC 123 Attach
sheet- 1-2
Solder
I I I I I I I I
‘0 2 4 6 8 10 12 14 16 18 20
Soldering time (sl
230°C
25C
4. Outline
Pollution DINVDEOllO 2
6.2 Please don’t carry out isolation test (Visa) over U,,. This
product deteriorates isolation characteristics by partial discharge
due to applying high voltage (ex. U,,). And there is possibility
that this product occurs partial discharge in operating isolation
voltage. NJ,,,, 1.
SHARP CORPORATION ED-94040E 1 March 5, 1998
MODEL No. 1 PAGE
PC123Y (Option) Attach
sheets-2-3
4. Outline
Rankmark
kL-
6
‘II I
\
v :..,
PC1
/I
i-..
I
1: Anode
2: Cathode
.m
Pin Nos. and
connection diagram
internal
4: Collector
3: Emitter
7.62’0.3
1
L Drawing
No.
CY7252K02
SHARP CORPORATION
MODEL No. PAG E
PC123Y (Option) Attach
sheets-2-4
Method of Diagram 1 : Breakdown test (Apply to type test and sampling test)
Unr(1136V)
5. t4 =O.l s
I$ (Partial discharge =l s
U low (71Ov) measuring time)
__ ___._._.-_....._.-_.--------..-..-.-----.------.-. tb =1.2 s
>t
& _ 5 _ t4 _
tb
It *
Fig. 6 Safety maximum power dissipation Fig. 7 Safety maximum forward current
vs. ambient temperature vs. ambient temperature
(When failed) (When failed)
www.datasheetcatalog.com