Professional Documents
Culture Documents
Página 1 de 7
Tela anterior
Bem-vindo: cdbxsl1
Service Magazine
2002/07/08
Número de Mídia -SEPD0637-00 Data de Publicação -08/07/2002 Data de Atualização -08/07/2002
i01765475
Motor Grader:
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 2 de 7
Service Magazine SEPD0594, 04 September 2001, "Hardened Full Length Moldboard Rails Are
Available for Parts Service". Disregard the article. Reference the following article.
Longer rails for the moldboard are now available. The new rails replace the former rails that were
0.9 m (3.00 ft) long. The new rails are hardened except for the ends of the rails. This will
accommodate the holes for the brackets for the sideshift cylinder that must be drilled and tapped.
Refer to the following table for the correct part numbers.
Table 1
Moldboard Rails
Length of Former Part New Part
Model
Moldboard Number Number
Use the following procedure for the installation of the longer rails.
1. Use a suitable method to remove the existing rails that are on the moldboard.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 3 de 7
Illustration 1 g00802263
Side view of the position of the 112-1815 Moldboard Rail and the 112-1816 Moldboard Rail
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 4 de 7
Illustration 2 g00802253
Side view of the position of the 112-1813 Moldboard Rail and the 112-1814 Moldboard Rail
2. Use the appropriate illustration in order to position the new rails. Use a 10 mm (0.4 inch)
fillet weld to weld the rails to the moldboard. Use E7018 welding electrode.
Note: The top rail and the bottom rail must be replaced at the same time on the following
models of motor graders: 120G, 120H, 130G, 130H, 140G and 140H. The cross section
view of the new rails are different from the existing rails.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 5 de 7
Illustration 3 g00802272
(M) Hole that is 16.75 mm (0.660 inch) in diameter with 3/4 -10 thread
Illustration 4 g00802290
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 6 de 7
(U) Hole that is 16.8 mm (0.66 inch) in diameter with 3/4 -10 thread
Illustration 5 g00803311
(Z) Hole that is 19.8 mm (0.78 inch) in diameter with 7/8-9 thread
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020
16H Motor Grader 6ZJ00001-UP (MACHINE) POWERED BY 3406C Engine(SE... Página 7 de 7
Illustration 6 g00803355
(BB) Hole that is 19.75 mm (0.778 inch) in diameter with 7/8 - 9 thread
(GG) Centerline
3. Drill the holes and tap the holes for the brackets for the side shift cylinder in the new rails.
Reference the appropriate illustration for the dimensions.
Direitos Autorais 1993 - 2020 Caterpillar Inc. Fri Aug 21 10:26:28 UTC-0300 2020
Todos os Direitos Reservados. cdbxsl1
Rede Particular Para Licenciados SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 21/08/2020