Professional Documents
Culture Documents
RS600C
Reclaimer/Stabilizer
RS600C Reclaimer/Stabilizer
Center-mounted Cutter
The RS600C’s heavy, unitized mainframe with center-mounted 600 hp
engine and cutter distribute the machine’s 61,880 lb (28,068 kg) weight
and horsepower for the highest possible production while a direct
V-Belt driven, four-speed rotor transmission provides the cutter torque
needed to tackle tough applications. The V-Belt power bands are up
to 25% more efficient than hydrostatic drives and they isolate the drive
train from cutter generated shock loads for longer component life and
less down time.
Bi-directional Operation
By changing travel direction, the operator can use the RS600C’s
“up-cut” and “down-cut” capabilities to the best advantage while
avoiding turns at the end of a working pass. This means the machine
spends more time working on the job site and less time maneuvering
into position to work. Specifications are easier to achieve because the
operator can match working direction and cutter speed range for
optimum gradation and blending control while maintaining maximum
production.
Hydraulic System
Main Tank Capacity 45 gal (170 L)
Hydraulic System Filter 10 micron absolute
Beta10 ≥100
Ground Drive Chrg. Oil Filter 12 micron absolute
Beta12 ≥ 200
11' 4"
(3,450 mm)
RS600C Reclaimer/Stabilizer
Operator Controls Air System Operating Dimensions
Modular operator station swivels forward to rearward, One 18 gal (68 L) reservoir, one engine mounted Wheel base 20 ft 4 in – 21 ft 4 in (6,200 – 6,500 mm)
180,° providing excellent visibility of the work area in compressor, approximately 13 ft3/min 125 psi (.37 m3/min) Wheel track 7 ft 3.5 in (2,220 mm)
either direction. (8.6 bar) safety valve, quick couplers for hook-up Turning radius 17 ft 1 in (5,200 mm)
Machine stability and low vibration reduce operator on air impact tool. Processing width 8 ft (2,430 mm)
fatigue. Operating height – maximum (with legs extended)
Highly visible systems gauges and controls. Optional Equipment Without ROPS 15 ft 2 in (4,620 mm)
Microprocessor-based control system automatically
58 in (1,470 mm) diameter cutter mandrel for 20 in
maintains cutting depth, cross slope and travel speed. Transport Dimensions
(508 mm) cutting depth.
Engine load sensing system automatically adjusts travel
Water/Emulsion Spray System - manual and automatic
speed to cutting conditions, maintaining optimum use of Weight approx* 61,880 lbs (28,068 kg)
modes, 30-600 gal/min (114-2,271 L/min) with flowmeter,
engine horsepower. Width 9 ft 11 in (3,023 mm)
remote display.
An LCD readout provides a continuous display of cutting Length 26 ft 9 in (8,150 mm)
Rear (bolt-on) tow hook attachment.
depth, travel speed and percent of cross slope. The Transportation height – minimum* 11 ft 4 in (3,450 mm)
microprocessor also permits a complete online review of Automatic Cross Slope System.
all machine operations to assist in operator training and ROPS *Dimensions will vary depending on options.
trouble shooting problems in the engine or electrical and Heavy-duty front door
hydraulic systems. Important note: All electrical specifications used herein refer
to U.S. standards of voltage and frequency. Any electrical
Elevation control is manual or automatic with the right equipment that is factory installed will be compatible with
legs tied together, permitting automatic control of cross power availability requirements of any customer’s country.
slope. (Optional)
Note: All dimensions and weights provided with standard
Manual backup control system.
width cutter. Operating and transportation dimensions and
Gross horsepower based on SAE J1995 standard weights will vary depending on selected options.
conditions 77°F (25°C) and 29.3 in (99 kPa) hg using
35 API gravity fuel and engine equipped with fuel,
lube oil and jacket water pumps. No derating required
up to 3,300 ft (1,006,000 mm) altitude.
Effective Date: July 2008. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes
only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to
otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale
and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks, or trade names of Terex Corporation and/or its subsidiaries in the
USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. Copyright 2008 Terex Corporation.
Terex Roadbuilding
P.O. Box 1985, Oklahoma City, OK 73101
(405) 787.6020 1-888-TEREXRB
www.terexrb.com