Professional Documents
Culture Documents
COM
FAN COIL
THERMOSTATS
AN OVERVIEW
Fan Coil Thermostats
TABLE OF CONTENTS
FEATURES....................................................................................................3
PROGRAMMING.........................................................................................5
WIRING DIAGRAMS...................................................................................6
Fan Coil Thermostats
FEATURES
The table below describes the thermostats that will be provided.
3
Fan Coil Thermostats
COOL/HEAT
T-STAT TYPE SYSTEM TYPE T-STAT CODE CONTROL TYPE C FAN CONTROL WATER CONTROL AVAILABLE
CHANGEOVER
N03H Heat Only None
“N-SERIES”
N03C Cool Only None
Thermostat/BAS Auto
DIGITAL 2-pipe ON/OFF Actuator Only
N05 Heat/Cool Auto (H-M-L, or based on demand),
or set by user (H-M-L)
NETWORKING N07 Heat/Cool with Auxiliary Electric Heat Auto
COMPATIBLE N08 Cool with Electric Heat Auto
4-pipe N11 Heat/Cool Auto Same as above Same as above
F03H Heat Only None
“F-SERIES”
F03C Cool Only None
Thermostat/BAS Auto
DIGITAL 2-pipe
F05 Heat/Cool Auto (H-M-L, or based on demand), Floating Point Actuator Only
or set by user (H-M-L)
NETWORKING F07 Heat/Cool with Auxiliary Electric Heat Auto
COMPATIBLE F08 Cool with Electric Heat Auto
4-pipe F11 Heat/Cool Auto Same as above Same as above
P03H Heat Only Nonea
“P-SERIES”
P03C Cool Only Nonea
Thermostat can switch fan speeds
DIGITAL 2-pipe
P05 Heat/Cool Autob (H-M-L) based on demand, ON/OFF Actuator Only
or manually by user*
7-DAY P06 Heat/Cool with Auxiliary Electric Heat Autob
PROGRAM P08 Cool with Electric Heat Autob
4-pipe P11 Heat/Cool Autoc Same as above Same as above
D03H Heat Only None
“D-SERIES”
D03C Cool Only None
Thermostat can switch fan speeds
DIGITAL 2-pipe
D05 Heat/Cool Auto (H-M-L) based on demand, ON/OFF Actuator Only
or manually by user*
NO 7-DAY D06 Heat/Cool with Auxiliary Electric Heat Auto
PROGRAM D08 Cool with Electric Heat Auto
4-pipe D11 Heat/Cool Auto Same as above Same as above
V03H Heat Only
“V-SERIES” None
V03C Cool Only
Thermostat/BAS auto
DIGITAL 2-pipe
V05 Heat/Cool (H-M-L, or based on demand), Proportional Actuator Only
or set by user (H-M-L)
NETWORKING V07 Heat/Cool with Auxiliary Electric Heat Auto
COMPATIBLE V08 Cool with Electric Heat
4-pipe V11 Heat/Cool Auto Same as above Same as above
NOTES: Fan and valves are controlled with a 24VAC signal sent from the thermostat to the relay board via the appropriate terminal.
* Manual fan setting would force fan OFF, or into continuous operation at set speed.
a. Can be programmed to turn ON/OFF based on schedule desired
b. Changeover can occur based on room temperature demand, or operation can be automated based on user schedule.
c. OFF mode is available for all thermostats.
EDGE will automatically prevent the user from selecting something that is not compatible with the current configuration. This means that the code may seem
unavailable (greyed out), at first.
This could be due to the actuator type (ON/OFF or Floating) or a fan speed control option chosen.
For “N”,”F” and “V” series specifically, this is also due to the requirement to specify networking capability. Under “Network Capability” choose either
Standalone or BACnet Enabled to then see the available N-series , V-series or F-series thermostats.
4
Fan Coil Thermostats
PROGRAMMING
Below are some of the common defaults the thermostats are programmed with at the factory. These are subject to change
with each order based on the configuration.
TEC3000 Series
Catalog Page: LIT-1901109
Product Bulletin: LIT-12013193
FCP
Product Bulletin: LIT-12013641
User Guide: LIT-12013635
5
Fan Coil Thermostats
WIRING DIAGRAMS
Below are examples of wiring the thermostat to the factory provided control board.
230v P9
P4
208v P8
P3
155v P7
P2
P1
277v P10
NEUT
JP2
L2
LINE VOLTAGE IN S1
TS1 S2
MTR R TS1 (R)
PWR T1 C 24V-HOT TB4
TS2 C TS1 (S1)
TRANSFORMER Y1
BO5-AUX TB6
NEUT TS2 (Y1) 6
25 VA W1
24V-COM TB5
TO FAN MTR
JP3
(HIGH)
HEAT
COM
COM
LOW
MED
FAN-H TB1
R
R
RS TB13
TB1.H
1 FAN-H
TB1.M
2 FAN-M
TB1.L
3 FAN-L
TB1.R
EARTH 4 24V~HOT
TP1 S1 TH1.5 TB1.S1
5 24V~COM
S2
TP2
R TH1.4 6 B05 AUX
C 7 B05 AUX
C 8 B03
G TB1.W1
10 9 BO4
H TH1.1
1 10 BO1
M TH1.2 TB1.Y1
11 BO2
L TH1.3
12 BI1
W1 TH1.9
13 RS
Y2
14 SCOM
Y1 TH1.11
15 BI2
16 UI3
NOTES: BO4 and BO2 are the heating and cooling terminals, respectively. For wiring peripheral devices (window switches, auxiliary heat, etc.) and
programming of the thermostat, see the installation manual and/or reach out to Krueger Application Engineering.
6
CONNECT WITH US!
Let us know how we can assist you in your next building application. For more information, contact
your local Krueger representative or visit us on the web at www.krueger-hvac.com.