refer to Operation and Maintenance Manual, NOTICE The machine must be stopped and engine at low idle SEBU8624, “ Cat Detect Object Detection”. before changing directions. i02978949 After moving the shift lever, do not accelerate until after hearing or feeling the transmission clutches Service Ports engage.
SMCS Code: 0350
Illustration 121 g01243936
The service ports are located on the panel behind the companion seat.
Power Receptacle (1) – This port
provides 12 V power. Illustration 122 g01519384 (1) Transmission control ET Service Port (2) – This service port allows service personnel to connect a Make sure that the machine is stopped and that the laptop computer that is equipped with engine is at low idle when you move the transmission the Electronic Technician (ET). This will allow control to the PARK position. When the transmission service personnel to diagnose machine systems control is in the PARK position, the transmission is in and the engine. NEUTRAL and the parking brake will engage. Make sure that the machine is stopped and that the TPMS or VIMS Service Port (3) – This engine is at low idle when you change direction port allows service personnel to between FORWARD and REVERSE, or between connect a laptop computer with the REVERSE and FORWARD. software for the Vital Information Management System (VIMS). When you move the transmission control lever from NEUTRAL to any forward speed, first gear is Product Link Service Port (4) – This port engaged. At low ground speeds, the machine will be allows service personnel to connect a in torque converter drive. laptop computer with the software for the product link system. When the engine accelerates and the ground speed increases, the transmission automatically upshifts. During higher ground speeds of first gear and of i03646132 other forward gears, the lockup clutch will be engaged. Then, the machine is in direct drive. When Direction and Speed Control the engine speed slows and the ground speed decreases, the transmission automatically SMCS Code: 3100; 7000 downshifts. During shifts, the machine will be in torque converter drive. Upshifting and downshifting NOTICE are controlled automatically. The transmission will not To avoid striking overpasses, electrical power lines shift until the proper ground speed is achieved. You and obstructions, always lower the body before mov- can not force the transmission to shift by moving the ing the machine. transmission control lever. 98 SEBU7790-12 Operation Section Engine Lockout Control
For more information on the transmission control, Reverse Neutralizer
refer to Operation and Maintenance Manual, “Operator Controls”. If the body is raised and the transmission is in REVERSE, the transmission will shift into NEUTRAL. Shift Inhibiting The transmission will not shift into REVERSE until the body is lowered completely and until the transmission control is moved into NEUTRAL. The Use the Electronic Technician (ET) to program the hoist control must also be in the HOLD or FLOAT gear limit. See Troubleshooting, Systems Operation, position. Testing and Adjusting, RENR8342, “Chassis Electronic Control system” for additional information. Limiting Body Up Gear Shifting is limited in the following situations: engine The body up gear limit is programmed to first gear at overspeed protection, coasting in neutral, the factory. The machine will not operate above the management of directional shifts, limiting top gear, programmed gear limit until the body is completely reverse neutralizer and limiting body up gear. down. The gear limit must remain set to first gear on machines with a “CE” mark (plate). The “CE” mark is Engine Overspeed Protection on machines that are compliant with the requirements of the European Union. For machines This machine is equipped with automatic engine without the “CE” mark, the body up gear limit can be overspeed protection. If the engine speed reaches changed to second or third gear by using the 2475 rpm, the ARC system will automatically engage, Electronic Technician (ET) that is available from your regardless of the position of the ARC switch. In order local Caterpillar dealer. to prevent further engine overspeed, the transmission will upshift one gear if the engine speed i04373650 reaches 2750 rpm and the transmission is in the same actual gear as the selected gear on the transmission control. Engine Lockout Control SMCS Code: 1000; 7000 NOTICE Do not exceed 2750 rpm or engine damage can This machine is equipped with an Engine Lockout result. Control and a Machine Lockout Control. Do not activate both types of lockout controls at the same time. Coasting in Neutral The transmission will not shift into NEUTRAL if the machine speed is above 8 km/h (5 mph).
Management of Directional Shifts
If the transmission is in a forward gear and the transmission control is moved into the REVERSE Illustration 123 g01520019 position, the transmission will remain in forward gear until the machine speed is below 8 km/h (5 mph). The engine lockout control allows the engine to be Then, the transmission will shift into NEUTRAL. The disabled while service is performed. Use the engine transmission will not shift from NEUTRAL into REVERSE until the machine speed is below 5 km/h lockout control to prevent accidental activation of the (3 mph). following: • The engine starter Limiting Top Gear • The secondary steering The transmission will not shift to a gear above the selected top gear limit. The machine comes from the • The prelube function (if equipped) factory with the highest gear as the top gear limit. Use the Electronic Technician (ET) to change the top gear limit.