Professional Documents
Culture Documents
E3x-Hd Omron
E3x-Hd Omron
● フルオートチューニング
スマートファイバセンサ
1-1 外形寸法図 2-1 操作・表示早見表 1. 検出体が無い状態で ボタンを長押しし、赤デジタルに [ ]→[ ]→[ ]
5.2
[L/D 表示灯 ] [DPC 表示灯 ]
DynamicPowerControl 機能有効時に点灯します。 パワーチューニング
取扱説明書
黒:出力 入光時 ON(L)/ しゃ光時 ON(D) 7 秒以上長押しします。検出体を通し終えたら、 ボタンから指を離してください。)
10
の設定状態を表示します。 光量が飽和
青:0V した場合 MODE
4.2
このたびは、本製品をお買い上げいただきまして、 SmartTuning 実行時に点灯します。 設定初期化 →
5.1 146.9(カバー開時最大) 出力 ON 時に点灯します。
104.8 (カバー開時最大)
まことにありがとうございます。 L/D
・この取扱説明書をよくお読みになり、十分にご理解のうえ、
37
正しくご使用ください。 ゼロリセット
・この取扱説明書はいつでも参照できるよう大切に保管して しきい値 受光量
UP
緑デジタル 赤デジタル
7秒以上長押し
ください。
33.5
9 「③ 便利な設定編」
4.5
2- Ø 2.4 検出体
(13)
12.7
感度設定 しきい値の微調整 モード切替 出力切替
© OMRON Corporation 2014 All Rights Reserved. 【 】ボタン 【UP/DOWN】ボタン 【MODE】ボタン 【L/D】ボタン
* 4 0 1 8 7 1 9 - 1 B * 20.5
5.7
< 省配線コネクタタイプ > 検出体ありとなしで 1 回ずつ押します。 緑デジタルのしきい値が 3 秒以上長押しすること 1 回押すことで
37.9 20.5 入光時 ON(L)/ しゃ光時 ON(D) を切替えま
設定完了
[ST 表示灯 ] が点灯します。 変わります。 で、設定モードと検出
細径ファイバ用アタッチメント
安全上のご注意 ( 形 E39-F9) 装着時 71.8
モードを切替えます。 す。[L/D] 表示灯の点灯が切替わります。
2 4
< コード引き出しタイプ > 1 3
● 警告記号の意味 出力切替方法
12.7
2-2 受光量設定 :1 のときの最大受光量をパワーチューニングレベルに調整します。
( ) 内の寸法は関連部品との寸法になります。 11.2 しきい値設定 : 1 のときの最大受光量と最小受光量の中間に設定されます。
正しい取扱いをしなければ、この危険のために、軽傷・中程度の傷害を <M8 コネクタタイプ >
警告 1. ボタンを押します。
負ったり、万一の場合には重症や死亡にいたるおそれがあります。また、
④ 検出体の位置を決めたい!
同様に重大な物的損害を受けるおそれがあります。 1-2 アンプユニットの取付け
L/D
設定モードでは以下の機能設定ができます。 検出モード時のデジタル表示を用途に
1. 検出体がない状態で ボタンと ボタンを 1 秒以上長押しします。 MODE
トラブル 原因 対応方法 機能遷移に表示している内容は、工場出荷時の内容です。 std 応じて変更したい場合
画面に何も表示 電源が入っていないか、 配線の見直し、電源電圧・電源容量の
UP/DOWN
10.
(b)
p-b 微小検出体もしくは移動が速い検出体でしきい値を設定したい場合
しきい値設定 :変更されません。しきい値が小さい場合、出力が正しく ON/OFF する最小の値に設定されます。 ほこりや汚れが影響 ピーク受光量 ボトム受光量
しています。 「⑤ 詳細設定編」 入光ピークの最小値と遮光ボトム
反射形の場合は、検出体がある状態にて実施してください。
受光量表示が変動する ほこりや汚れ・温度変化 DPC 機能を使えば、受光量表示が安定します。
MODE
(c)
bar (b)
8000 2000 の最大値を保持し、表示します。
位置決めチューニング実施後の場合、透過形・反射形ともに検出体ありの状態で実施してください。 ・振動等が影響しています。 「③ 便利な設定編」 2. 検出機能 (受光量例) 光量および応答時間を変更したい場合 (d)
アナログで直感でわかりやすい表示にしたい場合
エラー表示については、「2-3」のスマートチューニングエラー表を参照してください。 動作表示灯が点滅する 相互干渉等が影響 アンプの連結状態を確認して、
応答時間 光量
② ほこりや汚れで受光量が変化しても安定して検出したい ! しています。 電源を再投入してください。 (a)
hs 500 UP/DOWN
検出機能
(e) (c)
しきい値
120% 100% 80%
しきい値を 100%、表示範囲
を 80 ∼ 120% までとして
「1-2 アンプユニットの取り付け」 (a) HS 250μs 1( 基準 ) 現在値を表示します。
高速モード
● DPC 機能
DPC 機能は透過形 / 回帰反射形での使用をおすすめします。
受光量がー(マイナス) ゼロリセット機能が有効
になっています。
ゼロリセットを解除してください。
「③ 便利な設定編」
MODE
(b) stnd 500 (b) STND
光軸調整したい場合
表示になる 1ms 1倍
標準モード
1. スマートチューニングを実行してください。 DPC 機能有効時は 微分機能が有効に 微分機能を OFF にしてください。 (c)
6000 (c) GIGA
(d)
ピーク受光量 受光量
ピーク時の受光量を保持し、
緑デジタルに表示します。
DPC 表示灯が点灯します なっています。 「⑤ 詳細設定編」
ギガモード
16ms 12 倍 3500 3000
「2-3 スマートチューニング」 設定が分からなく
なってしまった
ー 設定初期化を行ってください。 (d)
s h s 125 (d) SHS NPN 50μs 連結時の ch 番号を知りたい場合
「③ 便利な設定編 パワーチューニング」 「③ 便利な設定編」 0.25 倍
最速モード* PNP 55μs ch 番号 受光量
2. 設定モードで DPC 機能を ON にします。 ● エラー表示 (e)
ch 番号と受光量を表示します。
検出機能のモードを変更するとスマート 3000
「⑤ 詳細設定編」 エラー名 / 表示 原因 対応方法 チューニングは解除されます。
・1、2 の手順は逆でも可能です。 DPCエラー* ファイバユニットの検出面などを拭き取り、
受光量がほこりや *検出機能を最速モードにした場合は、通信機能、 9. 反転表示 アンプを反対に設置したい場合
・スマートチューニングがエラーだった場合 / 微分機能・最大感度チューニングを実行した場合 / 汚れにより低下して 受光量を復帰させ再度、スマートチューニング 相互干渉防止機能は無効となります。
位置決めチューニングの 1 点目の受光量が小さい場合は、DPC 機能が無効となります。
・しきい値と受光量を常に一定に保つために、受光量をパワーチューニングレベルに補正します
2000 4000 います。 してください。
設定モードの受光量は参考値です。 %ff UP/DOWN
表示が反転します。
赤デジタルにしきい値、緑デジタルに
そのため、ヘッドの汚れ・位置ずれ、温度変化により受光量が変化しても安定して検出すること
「2-3 スマートチューニング」 検出モードにすると変化する可能性が有ります。
受光量が表示されます。
が出来ます。 EEPROM エラー 内部データの読み 電源を再投入してください。復帰しない
内部受光量の変化を
表示受光量 出し / 書き込みに 3. DPC 機能 受光量が変化しても安定して検出したい場合
MODE
場合は、設定初期化を行ってください。
補正し表示受光量を
受光量 失敗しています。
一定にします。 「③ 便利な設定編」
受光量が補正できなく ロックオン
キーロックが有効に キーロックを解除してください。
dp< %ff UP/DOWN
「③ 便利な設定編」
10. エコ機能
消費電力を低減したい場合
なった場合、表示受光量 Eco on
内部受光量
しきい値 が下がり、DPC 表示灯が
点滅します。
なっています。
「③ 便利な設定編」 MODE
dp< %n e<% %ff UP/DOWN
表示灯 ( 緑デジタル , 赤デジタル ) が消灯します。
ボタン操作すると、約 10 秒間点灯した後、
カレントオーバー 制御出力に過電流が 制御出力の負荷を確認して定格内にしてください。 4. タイマ機能 出力のタイマ時間を設定したい場合 消灯します。
時間 「4-1 トラブルシューティング」 流れています。 負荷が短絡していないか確認してください。 e<% %n
③ 設定を初期化したい !
MODE
オフディレイタイマ
----
入光時
1. ボタンを押したまま、 rst ■形 E3X-HD11, 形 E3X-HD6, 形 E3X-HD14(NPN タイプ ) ■形 E3X-HD41, 形 E3X-HD8, 形 E3X-HD44(PNP タイプ ) (b) %n-d 10 オンディレイタイマ
(b) 検出してから出力 ON
しゃ光時
入光時 ON
T
茶 ① 茶① を遅らせます。
ON OFF
3秒以上両押し
10 ご承諾事項
T
ボタンを 3 秒以上長押しします。 (c)
負荷
しゃ光時 ON
センサ主回路
センサ主回路 ON OFF
L/D ④
DC
ワンショットタイマ
2. で [rst] を選択し、 ボタンを押します。
項目 初期値 黒 制御出力 入光時
負荷
] を選択し、 ボタンを押します。 制御出力 L-on 12∼24V
T には、当社は当社商品に対して一切保証をいたしません。 ただし、次に掲げる用途であって
時間出力します。 しゃ光時 ON
UP/DOWN MODE
* 他の機能は詳細設定の表示内容になります。
ON OFF
も、当社の意図した特別な商品用途の場合や特別の合意がある場合は除きます。
青 ③ 青③
スマートチューニングは解除されます。 タイマ設定("----" 以外)のメニューで、 (a) 高い安全性が必要とされる用途(例:原子力制御設備、燃焼設備、航空・宇宙設備、鉄
ユーザーセーブの内容は初期化されません。
道設備、昇降設備、娯楽設備、医用機器、安全装置、その他生命・身体に危険が及び
ボタンを先に押すと出力が反転するので注意してください。 *①、
③、④は E3X-HD□4 のピン端子です。
ボタンを押した後、
ボタンにて
UP/DOWN うる用途)
L/D MODE
④ 設定を保存したい / 読み出したい !
タイマ時間を設定可能です。 (b) 高い信頼性が必要な用途(例:ガス・水道・電気等の供給システム、24時間連続運転
4-3 定格/仕様 (1 ∼ 9999ms、1ms 刻み、初期値 10ms) システム、決済システムほか権利・財産を取扱う用途など)
(c) 厳しい条件または環境での用途(例:屋外に設置する設備、化学的汚染を被る設備、
1. ボタンを押したまま ボタンを 3 秒以上長押しします。
形式
NPN 出力 形 E3X-HD11 形 E3X-HD6 形 E3X-HD14
5. パワーチューニング 受光量目標値 ( パワーチューニングレベル ) 電磁的妨害を被る設備、振動・衝撃を受ける設備など)
L/D
PNP 出力 形 E3X-HD41 形 E3X-HD8 形 E3X-HD44 レベル (d) カタログ等に記載のない条件や環境での用途
● ユーザーセーブ を変更したい場合
● ユーザーリセット 制御出力数 1
現在の設定を保存します。 保存した設定を読み出します。 接続方式 コード引き出しタイプ 省配線コネクタタイプ*1 M8 コネクタタイプ 9999 UP/DOWN
ボタンにてパワーチューニングレベルを設定可能です。
(100∼9999、1刻み、
初期値9999)
*(a)から(d)に記載されている他、本カタログ等記載の商品は自動車
じ)
(二輪車含む。以下同
向けではありません。自動車に搭載する用途には利用しないで下さい。自動車搭載
赤色 4 元素 LED(625nm)
2. で [ ] を選択し、 ボタン 2. で [rst] を選択し、 ボタン 光源(発光波長)
DC12V ∼ 24V±10% リップル(p-p)
10% 以下
用商品については当社営業担当者にご相談ください。
電源電圧
*上記は適合用途の条件の一部です。当社のベスト、総合カタログ、データシート等最新版
UP/DOWN MODE UP/DOWN MODE MODE
ボタンにてパーセントチューニングレベルを お客様相談室
0120-919-066
オフ状態電流:0.1mA以下 UP/DOWN クイック オムロン
● キーロック
UP/DOWN
055-982-5015(通話料がかかります)
APC(オートパワーコントロール) 常時 ON
使用周囲照度 受光面照度 白熱ランプ:20,000lx 以下、太陽光:30,000lx 以下 7. 微分機能 受光量変化を検出したい場合 電話
3秒以上両押し 動作時:1∼2台連結時:−25∼+55℃、 設定した応答時間の受光量変化の絶対値がしきい値 ■営業時間:8:00∼21:00 ■営業日:365日
周囲温度範囲 3∼10台連結時:−25∼+50℃、11∼16台連結時:−25∼+45℃ %ff UP/DOWN
より大きければ検出します。赤デジタルに設定した
●FAXやWebページでもお問い合わせいただけます。
保存時:−30∼+70℃
(ただし、氷結、結露しないこと) 応答時間の受光量の変化量が表示されます。
⑥ 受光量表示を 0 にしたい ! *UP/DOWN どちらかを押してください。
周囲湿度範囲 動作、保存時:35 ∼ 85%RH(ただし、結露しないこと) MODE
微分設定 応答時間 FAX 055-982-5051 / www.fa.omron.co.jp
絶縁抵抗 20MΩ以上(DC500V メガにて) 1 250μs
● ゼロリセット
受光量表示を 0 にします。しきい値もシフトします。
耐電圧 AC1000V 50/60Hz 1min. 2 2
3
500μs
1ms
●その他のお問い合わせ
納期・価格・サンプル・仕様書は貴社のお取引先、または貴社
振動(耐久) 10 ∼ 55Hz 複振幅 1.5mm X,Y,Z 各方向 2h
■ 実行 ■ 解除 担当オムロン販売員にご相談ください。
衝撃(耐久) 500m/s2 X,Y,Z 各方向 3 回 3 4
5
10ms
100ms オムロン制御機器販売店やオムロン販売拠点は、Webページで
0 2000 4000 質量(本体のみ) 約 65g 約 20g 約 25g ご案内しています。
-1999 4 ボタンにて応答時間を設定可能です。
材質 ケース、カバー:ポリカーボネート(PC) UP/DOWN
微分機能有効時は検出機能設定が無効となります。
3秒以上両押し 3秒以上両押し *1 コネクタは、E3XーCN11(親コネクタ3芯)、E3X-CN12(子コネクタ1芯)どちらのコネクタでも使用できます。 A v 2 0 1 4 年 7月
DPC 機能 / 微分機能 / スマートチューニングを実行すると、ゼロリセットは解除されます。 -3-
*2 検出機能を最速モード(SHS)に選択した場合は、通信機能が無効となり、相互干渉防止機能および通信機能は使用できません。
パワーチューニングを実施したE3X-DA-Sを含んで連結した場合は、相互干渉防止台数は6台まで、パワーチューニングを実施した B 5 パワーチューニング以外のスマートチューニングが
不可となります。パワーチューニングの調整範囲は
E3X-MDAを含んで連結した場合は、相互干渉防止台数は5台までとなります。 約 1 ∼ 1/100 倍となります -4-
1 Installation 2 Settings Adjust for Moving Workpiece without Stopping Line
Full Auto Tuning
Smart Fiber Sensor
1-1 Dimensions 2-1 Setting and Display Overview
E3X-HD Series
1. Hold the button without the presence of a workpiece, and pass the workpiece
21.7 27.1 Unit: mm + : Press both through while [ ] -> [ ] -> [ ] is displayed in red digital.
5.2
Brown: 12 to 24 VDC : Press both in sequence (Keep holding the button while the workpiece passes through, and hold 7
[L/D Indicator] [DPC Indicator]
10
Displays Turns ON when Dynamic Power Control is When Light seconds or longer until [ ] is displayed in red digital. After the workpiece passes
INSTRUCTION SHEET Blue: 0 V Incident Light ON(L)/No effective. Level is
MODE
4.2
Incident Light ON(D) setting. Saturated
[OUT Indicator] [ST Indicator] through, release your finger from the button.)
5.1 146.9 (Max. with the protective cover open) Setting Reset
Thank you for selecting an OMRON product. This sheet
Turns ON when Output is Turns ON when Smart Tuning is in progress. →
primarily describes precautions ON. L/D
37
UP/DOWN MODE
the product.
• Please read this manual carefully, and use it correctly after Zero Reset
thoroughly understanding the product. Threshold Level Incident Light UP
33.5
• Please keep this manual properly for future reference 9 Green Digital Display Level
4.5
Refer to " Convenient
whenever it is necessary. 2-2.4 dia. Red Digital Display Setting Features".
12.7
(13)
Workpiece Hold for 7 seconds or longer
Sensitivity Setting Minute Threshold Mode Change Output Switch
20.5 [ ] Button Adjustment [MODE]Button [L/D] Button
© OMRON Corporation
5.7
2014 All Rights Reserved. * 4 0 1 8 7 1 9 - 1 B * <Wire-saving Connector Model> A single press each for setting [UP/DOWN] Button Switches between SET A single press switches between
37.9 20.5 with/without a workpiece. The green digital value changes. mode and RUN mode by Incident Light ON(L)/No Incident Light
With an thin-diameter fiber [ST Indicator] turns ON. ON(D). [L/D] Indicator changes.
a long press (3 seconds
attachment (E39-F9) 71.8
PRECAUTIONS ON SAFETY 1
2 4
3
or longer) of the key.
<Pre-wired Model>
12.7
Meanings of Signal Words Setting is Completed
11.2 <M8 Connector Model>
2-2 Switching Control Output
Indicates a potentially hazardous situation which, if not Dimensions in parentheses () indicates the ones with related components. Incident light level setting: Adjust the max. incident light level on Step 1 as the power tuning level.
WARNING
avoided, will result in minor or moderate injury, or may result 1. Press button. Threshold setting: Set to the middle between max. and min. incident light levels on Step 1.
in serious injury or death. Additionally, there may be
significant property damage.
1-2 Mounting the Amplifier Unit L/D
Through-beam: Set to "No Incident Light ON" to turn the Determine Workpiece Position
■ Mounting on DIN Track output ON with a workpiece in the detection area. Position Tuning
Warning Indications
1. Let the hook on the Amplifier Unit's Fiber Unit [L/D Indicator] turns ON. Workpiece 1. Press button without a workpiece in the area.
WARNING connection side catch the track and push the
This product is not designed or rated for ensuring safety of persons
unit until it clicks. Reflective: Set to "Incident Light ON" to turn the 1pnt
either directly or indirectly. Do not use it for such purpose. ■ Removing from DIN Track output ON with a workpiece in the detection area.
Fiber Unit Connection Side Hook [L/D Indicator] turns ON.
Do not use the product with voltage in excess of the rated voltage. 1. Push the unit in the direction 1. Workpiece
Excess voltage may result in malfunction or fire. 2. Lift it up in the direction 2. 2 1
2. Place the workpiece at the desired position and hold button.
Never use the product with an AC power supply. Otherwise, Refer to "1-1. Dimensions" or check the side of
explosion may result. the unit for wire color and role indications.
2-3 Smart Tuning [Easy Sensitivity Setting]
PRECAUTIONS FOR SAFE USE ■ Mounting Amplifier Units in Group Hold for 3 seconds or longer
The following precautions must be observed to ensure safe operation of the product. Doing so may cause damage or fire. (Wire-saving Connector Type Models) DIN Track Detect for Workpiece Presence/Absence
• Do not install the product in the following locations. The red digital display changes .
(1) Locations subject to direct sunlight 1. Mount the Amplifier Units one at a time onto the 2 2-point Tuning
(2) Locations subject to condensation due to high humidity DIN track and push them until they click. If there is Setting is Completed
(3) Locations subject to corrosive gas
(4) Locations subject to vibration or mechanical shocks exceeding the rated values
no click sound (not locked), push the connector in 1. Press button with a workpiece in the detection area.
Incident light level setting: The Step 2 incident level is adjusted to half the power tuning level.
(5) Locations subject to exposure to water, oil, chemicals the direction of arrow 1 shown in the figure below
(6) Locations subject to steam with the connector fully inserted. 1 Threshold setting: Set to the same value as the Step 2 incident level.
(7) Locations subjected to strong magnetic field or electric field Use E3X-CN11 (Master connector) for the master Detect Transparent or Small Workpiece (Set Threshold by incident light level percentage)
• Do not use the product in environments subject to flammable or explosive gases.
Amplifier Unit and E3X-CN12 (Slave connector) for 1pnt
• Do not use the product in any atmosphere or environment that exceeds the ratings.
• To secure the safety of operation and maintenance, do not install the product close to high-voltage devices and power the slave Amplifier Units. Percentage Tuning
devices.
• High-Voltage lines and power lines must be wired separately from this product. Wiring them together or placing them in 2. Slide the Amplifier Units in the direction 2. 1. Turn ON Percentage Tuning in SET mode. Refer to " Detailed Settings".
the same duct may cause induction, resulting in malfunction or damage.
• Do not apply any load exceeding the ratings. Otherwise damage or fire may result. 3. Use End Plates (PFP-M: separately sold) at the both 2. Press button again without a workpiece in the detection area.
2. Press button without a workpiece in the area.
• Do not short the load. Doing so may cause damage or fire. ends of the grouped Amplifier Units to prevent them
• Connect the load correctly.
• Do not miswire such as the polarity of the power supply. from separating due to vibration or other cause.
4 per
• To use this device as connecting with each other, be sure to connect with the same power supply and turn ON the power
simultaneously. Using a separate power supply will influence the functions when connecting the devices to use them.
4. Tighten the screw on the End Plates using a driver. 3
2pnt
• Do not use the product if the case is damaged.
• Burn injury may occur. The product surface temperature rises depending on application conditions, such as the ambient Up to 16 Amplifier Units can be mounted in a group. Setting is Completed
temperature and the power supply voltage. Use caution when operating or cleaning the product. Under environments such as vibration, use an end plate
• When setting the sensor, be sure to check safety such as by stopping the equipment. Setting is Completed Incident light level setting: The Step 2 incident light level is adjusted to the
• Be sure to turn off the power supply before connecting or disconnecting wires. even with a single amplifier unit. Tighten the screw while pressing the End Plate. power tuning level.
• Do not attempt to disassemble, repair, or modify the product in any way. Incident light level setting: The larger incident level of the Step 1 and 2 values is Threshold setting: Set to the value obtained by [Incident Level at Step 2 x
• When disposing of the product, treat it as industrial waste. adjusted to the power tuning level.
• Do not use on underwater, rain or the outdoors. 1-3 Mounting Fiber Unit Threshold setting: Set to the middle between the Step 1 and 2 incident light levels.
Percentage Tuning Level + Incident Level at Step 2].
No Smart Tuning other than Power Tuning can be used if Percentage Tuning is set.
■ Use Fiber Cutter 2
PRECAUTIONS FOR CORRECT USE Step 1 and Step 2 can be reversed. Smart Tuning Error
1. Insert a Fiber Unit into a fiber cutter hole. Fiber Cutter E39-F4
(Provided with
• Be sure to mount the unit to the DIN track until it clicks. Error / Display / Cause Error Origin Tuning Type Remedy
• Use an extension cable with a minimum thickness of 0.3 mm2 and less than 100 m long. Insert a standard Fiber Unit up to the the Fiber Unit) Detect for Workpiece Presence/Absence Near Error
• Do not apply the forces on the cord exceeding the following limits: position in which it is cut; and 2-point Tuning • Change the detection function mode to a slower
Pull: 40N; torque: 0.1N·m; pressure: 20N; bending: 29.4 kg a thin-diameter Fiber Unit to the Thin-diameter
Fiber Unit Hole x 2
Maximum Sensitivity Tuning err Full Auto Tuning
Positioning Tuning
response time mode.
• The Sensor is ready to operate 200 ms after the power supply is turned ON. bottom of the hole. The light level difference • Narrow the emitter and receiver distance (Through-beam)
• When using a connector type product, place a protective label (provided with the E3X-CN series) on the power supply Standard Fiber Unit
Thin-diameter Fiber
Attachment: E39-F9
1. Hold button for 3 seconds or longer with/without workpiece as shown below. between Points 1 and 2 are
extremely small.
• Mount the sensor closer to the workpiece (Reflective)
connecting terminals that are not used, to prevent electric shock or short circuit. 2. Press down the blade at a single Hole (dia. 2.2 mm) x 3 1 Over Error
Release the button when [ ] is displayed. • Enhance the power tuning level.
stroke to cut the Fiber Unit. All
Through-beam: Workpiece is present err • Use a thin-diameter fiber.
■ Mount Fiber Unit Incident light level is too • Widen the emitter and receiver distance (Through-beam)
Lock Lever
high. • Distance the sensor from the workpiece (Reflective)
Protective Label
1. Open the protective cover. Lock
Release
Low Error
Tuning other than • Decrease the power tuning level.
4 Protective Cover
Power Supply Connecting Terminal
2. Raise the lock lever. 2 1
err Maximum Sensitivity
Tuning
• Narrow the emitter and receiver distance (Through-beam)
• Excessive incident light cannot be sufficiently handled by the mutual interference prevention function and may cause Workpiece Hold for 3 seconds or longer Incident light level is too low. • Locate the sensor closer to the workpiece (Reflective)
malfunction. To prevent this, set a higher threshold level. 3. Insert the Fiber Unit in the fiber Reflective: Workpiece is absent The adjustment range of smart tuning is approx. 20 to 1/100 times. When selecting Giga Mode as
unit hole to the bottom. The red digital display changes .
• Do not pull or apply excessive pressure or force on the Fiber Unit when it is mounted on the Amplifier Unit. 3 detection function, the range will be approx. 2 to 1/100 times due to the large initial value.
• The E3X-MC11-SV2 and E3X-MC11-S Mobile Consoles cannot be used.
• Mutual interference prevention does not function among the E3X-DA-N/SD/NA amplifiers. It functions among 4. Return the lock lever to the original Refer to " Detailed Settings" to change the powr tuning level.
E3X-DA-S/MDA models. position and fix the Fiber Unit. Fiber Unit
• The E3X-DRT21-S, E3X-CRT and E3X-ECT Communication Units cannot be used. 2-4 Minute Adjustment of Threshold Level
• Always keep the protective cover in place when using the Amplifier Unit. Not doing so may cause malfunction. When mounting a coaxial reflective
• Do not use thinner, benzine, acetone, and lamp oil for cleaning. Fiber Unit, insert the single-core Setting is Completed 1. Press button to adjust the threshold level.
• It may take time until the received light intensity and measured value become stable immediately after the power is turned UP/DOWN
on depending on use environment. Fiber Unit to the upper hole (Emitter Incident light level setting: The incident level in Step 1 is adjusted to "0". The threshold level becomes higher. The threshold level becomes lower.
• If you notice an abnormal condition such as a strange odor, extreme heating of the unit, or smoke,immediately stop using side) and the multi-core Fiber Unit to Threshold setting: The value is set to approx. 7% of the incident light level of 1.
the product, turn off the power, and consult your dealer. the lower hole (Receiver side). If the incident light level of 1 is smaller during long distance
Single Core detection, the minimum value by which an output is correctly
Checking the Package Content turned ON will be set. Hold the key for high-speed level adjustment.
Multi Core
• Amplifier Unit: 1 • Instruction Sheet (this sheet): 1 (Japanese, English and Chinese) -1- -2-
Function Setting Description
3 Convenient Setting Features 4 Maintenance 5 Detailed Settings B
Restore from the Incident Level Changed due to Dust and Dirt 4-1 Troubleshooting Hold button for 3 seconds or longer to enter SET mode. 8. Digital Display
Power Tuning Troubleshooting MODE Changing Digital Display in RUN Mode for
SET mode provides the function settings described hereafter. The initial display shown
1. Hold and
MODE
buttons for 1 second or longer without a workpiece in the area. Problem Cause Remedy after transition from one function to another represents the factory default. std UP/DOWN
Specific Purpose
Blank display No power supplied or Check the wiring, power supply voltage and
the cable broken Function Setting Description
st ptun
capacity.
MODE
Refer to "4-2 Input/Output Circuit Diagram" Checking a Margin Against Threshold
A Light Level
Eco mode is ON.
per
No digital display Turn OFF Eco mode. Refer to "5. Detailed Settings". Threshold The ratio of the incident light
Hold both for 1 sec. or longer
(a)
Ratio
Refer to " Detailed Settings". (a) level to the threshold is
Setting is Completed
1. Function Selection Changing Functions to Set in SET Mode 150p displayed in red digital figures.
p-b
Sensing/Detection Detection set to a small
Incident light level setting: The Step 1 incident level is adjusted to the power tuning level.
Threshold setting: Not changed. If the value is low, it will be set to the minimum
not possible despite
the minimum
light level mode
Dust or dirt influences
The GIGA mode setting enhances the light level
and a larger incident level is displayed. dflt UP/DOWN
[
[
]: Functions 1. to 5. can be set.
]: Functions 1. to 10. can be set.
(b)
Setting Threshold using a Small or Fast Moving
threshold level Refer to " Detailed Settings". Workpiece
value in which an output is turned ON/OFF correctly.
Perform the procedure with a workpiece in the area for reflective model setting. Incident light level Dust or dirt, temperature Use the DPC function to stabilize the incident light level display. MODE
(c)
bar Peak Light
Level
Bottom Light
Level
Holds and displays the minimum
(b)
value of the peak of the light
display fluctuation changes or vibration
If the setting is made after position tuning, set both the through-beam model and
reflective model with a workpiece.
Refer to " Convenient Setting Features"
2. Detection Function (Incident Light Level Example) Changing Light Level and Response Time
(d) 8000 2000 incident and the maximum value
of the bottom of the light interruption.
The operation Mutual interference Check the Amplifier Units mounted in a group and
Refer to "2-3 Smart Tuning Error" for error displays. indicator blinking or other reason turn ON the power again.
Refer to "1-2 Mounting Amplifier Unit"
(a)
hs 500 UP/DOWN
Detection Function Response Light Level
Time (e)
Setting for Intuitive Analog Display
Threshold Displays the current level in the
Stable Detection Regardless of Incident Level Change due to Dust and Dirt HS (c) 120% 100% 80% 80 to 120% range against the
(a)
DPC Function
Incident light level
displayed in a
The zero reset function
is enabled.
Cancel the zero reset function.
Refer to " Convenient Setting Features" MODE
(b) stnd 500 High-speed Mode
STND
250 µs 1 (Standard)
threshold value (100%).
Use of the DPC function with through-beam model or regressive reflection model is recommended.
negative value (b) 1 ms 1 time Adjusting Optical Axis
1. Perform Smart Tuning.
The DPC indicator turns ON
when the DPC function is
The differential
function is enabled.
Turn OFF the differential function.
Refer to " Detailed Settings".
(c)
6000 Standard Mode
GIGA
(c) Giga Mode 16 ms 12 times
Peak Light
Level
Light Level Holds the peak incident light
Refer to "2-3 Smart Tuning" effective. (d) level and displays it in green
ー Reset the settings. 3500 3000
s h s 125
Lost tracking of
(d) SHS digital figures.
Refer to " Convenient Setting Features the settings made NPN 50 µs
- Power Tuning"
Refer to " Convenient Setting Features" (d) Super High-speed 0.25 times
2.
Mode* PNP 55 µs Checking the Channel No. in Group Mounting
Set the DPC function ON in SET mode. Error Display
Ch. No. Light Level
Refer to " Detailed Settings". Error Name / Display Cause Remedy Smart Tuning is canceled if the detection mode (e) Checking the Channel No. in
level has other relevant areas and recover the original incident *The communication and mutual interference
2000 4000
• The DPC function will be disabled when a smart tuning error occurs, differential function with
deteriorated due light level. Then, perform Smart Tuning. prevention functions are disabled when the 9. Inverted Display Mounting Amplifier in Inverted Direction
maximum sensitivity tuning is performed, or the first incident light level of the positioning tuning
detection mode is set to Super High-speed Mode.
is low.
• The incident light level is corrected to the power tuning level to maintain stable threshold and
incident light levels. This provides stable detection regardless of the incident level changes EEPROM Error
to dust or dirt.
Failed internal
Refer to "2-3 Smart Tuning "
Turn ON the power again. Reset the
The incident light level in setting mode is a
reference value. It may be changed when
%ff UP/DOWN
Inverts the display upside down.
The digital display shows the threshold value in
caused by dirty sensor head, position error, or temperature changes. data read/out settings if the error is not corrected. red, and light incident level in green.
switched to detection mode.
MODE
Displayed Incident Light Level Stabilizes the displayed Refer to " Convenient Setting Features"
incident level by correcting 3. DPC Function Stable Detection Regardless of Incident Light
Incident Light Lock ON
internal incident level changes. The key lock Cancel the key lock function. Level Change
Level
The displayed incident level function enabled
Refer to " Convenient Setting Features"
dp< %ff UP/DOWN
%n
possible. Refer to "4-2 Input/Output Circuit Diagram" operation.
Time and "4-3 Ratings and Specifications" 4. Timer Function Setting Output Timer MODE e<% Eco Lo
Refer to "4-1 Troubleshooting"
Reset Settings * The DPC indicator blinks. Indicators (Green and Red digital displays)
Incident ON
T
A e<% l% turn ON with low brightness in approx.
10 seconds after a key operation.
Light
-ON OFF
Initializes all the settings by returning them to the factory defaults. E3X-HD11, E3X-HD6, E3X-HD14 (NPN Type) E3X-HD41, E3X-HD8, E3X-HD44 (PNP Type) (a) the detection time is too No
Incident ON
T
Light OFF
Brown ① ① MODE
Brown short. -ON
Load
] in and press button. One-shot Timer Incident Light
UP/DOWN
Threshold Value 55
③ ③ Keeps the output ON for
No Incident Light provide applicable third party certification documents identifying ratings and
(c) a specified time regardless T
MODE Blue Blue
Incident
D s Oct, 2014
When a power tuned E3X-DA-S is included, up to six units can be connected with the mutual interference
The zero reset function is canceled when either of the DPC function/differential prevention function enabled. When a power tuned E3X-MDA is included, up to five units can be connected with The adjustment range of powr tuning is approx.
function/Smart Tuning is performed. -3- the mutual interference prevention function enabled. 1 to 1/100 times. -4-
1 设置 2 设定 ③ 想要不停止运行、通过移动的检测物体进行调整!
● 全自动调整
智能光纤传感器
1-1 外形尺寸图 2-1 操作・显示一览表 1. 在无检测物体的状态下持续按 按钮,并在红色数字依次显示为[ ]→[ ]
5.2
茶色:DC12-24V [L/D 指示灯 ] [DPC 指示灯 ] 直至红色数字显示为[ ]。完全通过检测物体后,请将手指从 按钮上放开。)
启用 DynamicPowerControl 功能时亮灯。 光量调整
10
ON(D) 的设定状态。
状态时 MODE
蓝色:0V
[OUT 指示灯 ] [ST 指示灯 ]
4.2
设定初始化
104.8 (保护罩打开时最大)
本次承蒙惠购本产品,谨致谢意。 5.1 146.9(保护罩打开时最大) 输出为 ON 时亮灯。 执行 SmartTuning 时亮灯。 →
使用时,请务必遵守以下内容。 L/D
37
・请妥善保管本使用说明书,以便随时参阅。
归零重置
UP
阈值 受光量
持续按7秒以上
33.5
9 绿色数字 红色数字 “③ 便利的设定 ”
4.5
2- Ø 2.4 检测物体
欧姆龙公司
12.7
(13)
灵敏度设定 阈值微调 模式切换【MODE】 输出切换【L/D】按钮
【UP/DOWN】按钮 按钮
© OMRON Corporation 2014 All Rights Reserved. * 4 0 1 8 7 1 9 - 1 B * 20.5 【 】按钮
5.7
37.9 20.5 < 省配线连接器型 > 检测物体有和无时各按一次。 绿色数字的阈值发生变化。 按住持续 3 秒以上,即可 按 1 次即可进行入光时 ON(L)/ 遮光时
[ST 指示灯 ] 亮灯。 在设定模式和检测模式之 ON(D) 的切换。
安装细径光纤用附件
安全注意事项 ( 型号 E39-F9) 时 71.8 2 4
间进行切换 [L/D] 指示灯作亮灯切换。
12.7
● 警告标识的含义 输出切换方法
11.2 受光量设定:将 1 时的最大受光量调整为光量调整等级。
若使用不当,则有可能对人身造成轻度或中度伤害, ( )内的尺寸为相关元件的尺寸。 <M8 连接器型 > 阈值设定:被设定为 1 时最大受光量和最小受光量的中间值。
警告 严重情况下甚至导致重伤或死亡。 1. 按 按钮
此外,还可能造成重大的经济损失。 1-2 放大器单元的安装
L/D
④ 想要确定检测物体的位置!
对射型:有检测物体时,想使产品进入 ON 状态,
● 警告标示 ■安装至 DIN 导轨 则设定为“ 遮光时 ON”。 ● 定位调整
1. [L/D 指示灯 ] 的 亮灯。 1. 在无检测物体的状态下按 按钮。
警告 将光纤单元插入部侧的卡槽卡在导轨上,
一直将锁钩推入至听到咔嚓声为止。
检测物体
安全要点
配线的颜色及功能请查看“1-1 外形尺寸图 ” 2-3 智能调整【简单灵敏度调整】
或主机侧面的标签。
为了确保您的安全,请务必遵守以下内容。否则可能会引起损坏或火灾。 持续按3秒以上
・ 请勿在以下环境中使用。 ① 想要检测有 / 无检测物体!
①阳光直射的场所 DIN导轨 红色数字显示为 [ ] 切换为 [ ]。
■连接后使用时(省配线连接器型) ● 2 点调整
②湿度高、易结露的场所
③有腐蚀性气体的场所 1. 2
设定完毕
④振动或冲击超出额定范围的场所
将各台放大器单元分别安装至DIN导轨,插入连接器 1. 在有检测物体的状态下按 按钮。
受光量设定:将 2 时的受光量调整为光量调整等级的一半。
⑤有水、油、化学药品等飞溅的场所
至听到咔嚓声为止。不易听到咔嚓声(锁定)时,请在
阈值设定:设定为与 2 时的受光量相同的数值。
⑥接触到蒸气的场所 将连接器插入深处的状态下,将连接器向箭头1方向
1
⑦强电场、强磁场的场所
・ 请勿在有易燃、易爆气体的环境下使用。
推入。
1pnt ⑤ 想要检测透明物体或微小物体! ( 想要通过受光量比率设定阈值! )
请在母机上使用型号E3X-CN11(母连接器)、
・ 请勿在超出额定范围的环境下使用。
子机上使用型号E3X-CN12(子连接器)的产品。 ● 百分比调整
・ 请将传感器设置在远离高压或动力设备的地方,以免操作或维护时发生危险。
・ 请将传感器和高压线、动力线分开排线。若使用同一排线或在同一线槽内排线,会相互感应, 2. 使放大器单元朝方向 2 滑动。 1. 在设定模式下将百分比调整设定为 ON。 “⑤ 详细设定 ”
引起错误动作或破损。
・ 请确保负载在额定范围以下使用。否则可能会引起损坏或火灾。 2. 在无检测物体的状态下按 按钮。
・ 请勿让负载短路。否则有导致损坏、起火的危险。 3. 请使用另售的终端架(型号 PFP-M)夹紧放大器, 2. 在无检测物体的状态下再次按 按钮。
・ 请正确连接负载。 以防因振动等原因而导致放大器单元移动。 3 4
・ 请注意电源的极性,防止错误接线。 4. 请使用螺丝刀紧固终端架的螺钉。 per
・ 连接后使用时,请务必连接于同一电源,并同时接通电源。如果连接不同电源,则会影响连 2pnt
接时的功能。
・ 请勿在外壳破损的状态下使用。 最多可连接台数为 16 台。
・ 可能会导致烫伤。根据使用条件(环境温度、电源电压等)不同,传感器表面温度会升高, 有振动等现象时,也请在放大器单元单件上 设定完毕 设定完毕
因此在操作或清洁时请多加注意。 使用终端架。 请在按住的同时紧固螺钉。
・ 设定传感器时请停止装置运行,确认安全后再执行操作。
受光量设定:将 1、2 中受光量大的一方调整为光量调整等级。 受光量设定:将 2 时的受光量调整为光量调整等级。 “⑤ 详细设定 ”
・ 请务必切断电源后再安装或拆卸导线。
・ 请勿擅自拆卸、修理、改造本产品。 1-3 光纤单元的安装 阈值设定:设定为 1 和 2 时的受光量的中间值。 阈值设定:设定为 [2 时的受光量 × 百分比调整等级 + 2 时的受光量 ]。
・ 废弃时,请作为工业废弃物处理。
・ 请勿在水中,降雨中以及屋外使用。 ■光纤切断器的使用方法 2 1. 和 2. 的顺序可以相反。 设定为百分比调整后则无法执行光量调整以外的智能调整
使用注意事项 1. 将光纤单元插入光纤切断器的剪切孔。 光纤切断器
● 智能调整错误
型号E39-F4
・ 安装至 DIN 导轨时,请推压放大器直至钩爪完全嵌入导轨。 (光纤单元附件)
・ 请确保延长导线在 100m 以下。延长导线请使用截面积为 0.3mm2 以上的导线。
标准光纤单元请插入至想要切断的位置。
细径光纤单元请插入至深处。
② 想要加强防尘抗污力! 错误名称 / 显示 / 原因
Near Error
发生调整种类 对策
・ 施加于导线部的力请确保在以下数值范围。 细径光纤单元用剪切孔2个 2 点调整 ・请切换为检测功能响应时间较慢的模式。
拉伸 40N 以下、扭力值 0.1N・m 以下、压紧力 20N 以下、弯曲 29.4kg 以下 ● 最大灵敏度调整 全自动调整 ・请缩小投受光间距。(对射型)
・ 接通电源并经过 200ms 后即可检测。 细径光纤用附件 ・请使传感器接近工件。 (反射型)
・ 使用连接器型产品时,为了防止触电或短路,请在不使用的电源连接端子上,贴上保护用贴片。 2. 将切刀一口气按下进行切断。
标准光纤单元
(φ2.2㎜)用 1 型号E39-F9 1. 检测物体在以下状态下,持续按 按钮 3 秒以上,待 [ ] 显示后放开按钮。 第 1 点和第 2 点的受光量差
值太小。
定位调整
受光量设定:将 1 时的受光量调整为光量调整等级。
設定完了 无法检查 ・ 检测 微小光量模式。
受到灰尘或污垢影响。
受光量显示增大。 dflt UP/DOWN
[
[
]:可设定功能 1. ~ 5.。
]:可设定功能 1. ~ 10.。
(b)
p-b 想要通过微小检测物体或快速移动的检测物体设定阈值时
“⑤ 详细设定 ” 峰值受光量 谷值受光量
阈值设定:不会变更。阈值较小时,输出将被设定为可正确执行 ON/OFF 的最小值。
反射型时,请在有工件的状态下执行。
受光量显示变动 受到灰尘或污垢 ・ 温度变化 若使用 DPC 功能,受光量显示即可稳定。 MODE
(c)
bar (b)
8000 2000
保持并显示入光峰值的最小值
及遮光谷值的最大值。
・ 振动等影响。 “③ 便利的设定 ”
若在定位调整执行后,那么対射型 ・ 反射型均请在有检测物体的状态下执行。 2. 检测模式 (受光量范例) (d)
请确认放大器的连接状态 想要更改光量及响应时间时 想要通过模拟方式执行易于直观的显示时
动作指示灯闪烁 受到相互干扰等影响。 阈值
错误显示请查看“2-3”的智能调整错误列表。 并重新接通电源。
“1-2 放大器单元的安装 ”
(a)
hs 500 UP/DOWN
检测功能 响应时间 光量
(e) (c)
120% 100% 80% 以 100% 为阈值、80 ~ 120%
● DPC 功能
受光量显示为 -(负) 零重置功能为开启状态。 请解除归零重置。
“③ 便利的设定 ” MODE
(b) stnd 500 高速模式
(b) STND
想要执行光轴调整时
DPC 功能推荐在对射型 / 回归反射型产品上使用。 1ms 1倍
标准模式 峰值受光量 受光量
Lock ON
若受光量无法进行补正, 按键锁定为开启状态。
请解除按键锁定。
“③ 便利的设定 ”
MODE
dp< %n 10. 节电功能 想要削减电力消耗时
内部受光量 那么显示受光量将会下降、 Eco on
阈值 DPC 指示灯呈闪烁状态。 Current Over 请确认控制输出的负载,将其设定在额定范围。 4. 定时器功能 想要设定输出的定时时间时
e<% %ff UP/DOWN
指示灯(绿色数字、红色数字)熄灯。
控制输出的电流过载。请确认负载是否短路。 通过按钮操作,约亮灯 10 秒钟后即会熄灯。
③ 想要将设定初始化!
时间 “4-1 故障排除 ”
“4-2 输出输入段电路图、4-3 额定值 / 规格 ” UP/DOWN
OFF 延迟定时
检测时间短、且无法通过
入光时
遮光时
T
MODE e<% %n Eco Lo
(a) PLC 执行检测时,
入光时 ON
*DPC指示灯闪烁。
l%
-ON
执行按钮操作后亮灯约 10 秒钟左右,
OFF
A
● 设定初始化 (a) 维持输出 ON 的状态。 遮光时 ON
T
e<%
将所有设定内容初始化,恢复至出厂时状态。
4-2 输出输入段电路图 MODE
-ON OFF
然后指示灯 ( 绿字、红字 )
即会进入低亮度亮灯状态。
10
入光时
■型号 E3X-HD11, 型号 E3X-HD6, 型号 E3X-HD14(NPN 型 ) ■型号 E3X-HD41, 型号 E3X-HD8, 型号 E3X-HD44(PNP 型 ) (b) %n-d ON 延迟定时 遮光时
T
(b) 检测后延迟输
1.
入光时 ON
按下 按钮的状态 rst 茶色 ① ①
茶色
承诺事项
-ON OFF
10 出 ON 的状态。 T
(c)
负载
遮光时 ON
传感器主电路
④ 传感器主电路
-ON OFF
负载
-ON OFF
UP/DOWN MODE 阈值 55 12~24V 均,也可定时输出。 遮光时 ON
T
保证。但若是本公司特意为以下用途而设计、或有过特别协商的
3.
-ON OFF
通过 选择 [ ],按 按钮。 控制输出 L-on 蓝色 ③ 蓝色 ③ 情况下,可以用于以下用途。
UP/DOWN MODE
* 其他功能为详细设定状态。 在定时设定(" - - - - " 以外)菜单中按 按钮后,
智能调整被解除。
即可通过 按钮进行定时设定。
MODE
a) 需要高度安全性的用途(例:用于原子能控制设备、焚烧设备、
用户保存的内容不会被初始化。 *1、3、4 为 E3X-HD□4 的管脚端子。
请注意,若先按 按钮则会导致输出反转。 UP/DOWN
航空・宇宙设备、铁道设备、升降设备、娱乐设备、医用器、
(1 ~ 9999ms、1ms 刻度、初始值 10ms)
4-3
L/D
额定值/规格 安全装置、或其他可能危及到生命・人身安全的用途)
④ 想要保存 / 读取设定! 5. 光量调整等级 想要修改受光量目标值(光量调整等级)时
NPN 输出 E3X-HD11 E3X-HD6 E3X-HD14 b) 需要高可靠性的用途(例:煤气・水力・电力等的供给系统、
型号
1. 按下 按钮的状态按 按钮 3 秒以上。 PNP 输出 E3X-HD41 E3X-HD8 E3X-HD44 通过 按钮即可设定光量调整等级。 24小时连续运转系统、决裁系统、或其他牵涉到权利・财产的
● 用户保存
L/D
● 用户重置
控制输出数
导线引出型
1
省配线连接器型 *1 M8 连接器型
9999 UP/DOWN
[100~9999、1刻度、初始值9999]
用途)
连接方式
保存当前的设定。 读取已保存的设定。 光源(发光波长) 红色 4 元素 LED(625nm)
MODE “③ 便利的设定 ” c) 苛刻条件或环境下的用途(例:室外设备、易受化学污染的设
2. 通过 选择 [ ] 并按 按钮 2. 通过 选择 [rst] 并按 按钮 电源电压 DC12V ~ 24V±10% 波动(p-p)
10% 以下
功能选择为 [ ]时 备、易受电磁干扰的设备、易受震动・冲击的设备等)
通常模式:720mW 以下 ( 电源电压 24V 时 30mA 以下、12V 时 60mA 以下 )
d) 产品手册里未记载的条件或环境下的用途
UP/DOWN MODE UP/DOWN MODE
消耗电力 A
3. 通过 选择 [ yes] 并按 按钮 3. 通过 选择 [rst user] 并按 按钮 节电功能 ON:530mW 以下 ( 电源电压 24V 时 22mA 以下 , 12V 时 44mA 以下)
UP/DOWN MODE UP/DOWN MODE 节电功能 LO:640mW 以下 ( 电源电压 24V 时 26mA 以下、12V 时 53mA 以下 ) 功能选择为 [ ]时 *除上述a)~d)的记载事项,本产品手册等记载的商品不适用于机
控制输出 负载电源电压 DC26.4V 以下、集电极开路输出型 6. 百分比调整 想要检测透明物体或微小物体时 动车(包括两轮车,以下相同)。请勿搭载于机动车上使用。机动
请注意,若先按 按钮则会导致输出反转。 负载电流:1~3 台连接时 100mA 以下、4 台以上连接时 20mA 以下
L/D
(残留电压 负载电流 小于10mA:1V以下 负载电流 10~100mA:2V以下) 在“ ”菜单中按 按钮后,即可通过 车搭载用商品请咨询本公司销售人员。
⑤ 想要防止误操作! 无输出时电流 : 0.1mA 以下 per %ff UP/DOWN
MODE UP/DOWN