Professional Documents
Culture Documents
1 (15)
Prepared (also subject responsible if other) No.
Revision history
Contents
1 References ················································································································ 3
2 About this Document ··································································································· 3
3 General description ····································································································· 3
3.1 Encapsulation class ····································································································· 3
3.2 Temperature range ····································································································· 3
3.3 Reliability ·················································································································· 3
3.4 Connectors ················································································································ 3
3.5 Applicable safety standards ·························································································· 4
4 Electrical data ············································································································ 5
4.1 DC Characteristics ······································································································ 5
4.2 Fundamental RF Requirements ····················································································· 5
4.3 Communication Band Characteristics ·············································································· 5
4.4 Power Handling ·········································································································· 6
4.5 Reverse Intermodulation with Two TX Carriers ·································································· 6
4.6 Group Delay ·············································································································· 7
5 Mechanical Specification ···························································································· 11
5.1 Weight ···················································································································· 11
5.2 Wind Load ··············································································································· 11
5.3 Dimensions·············································································································· 11
5.4 Mounting Hole Pattern ······························································································· 11
5.5 Mechanicals Drawings ······························································································· 12
6 Requirement fulfilment ······························································································· 15
6.1 Vendor specified requirements ···················································································· 15
6.2 Requirement deviations: ····························································································· 15
PRODUCT SPEC.
3 (15)
Prepared (also subject responsible if other) No.
1 References
[ref RS] 1056 – KRF 102 299
This product specification covers the following versions of the diplex filter.
3 General description
The purpose of the diplex filter (also referred to as product in this document)
is to enable feeder sharing between a low band (698-960 MHz) system and a
high band (1710-2690 MHz) system.
3.3 Reliability
3.4 Connectors
3.5.1 International
3.5.2 Europe
4 Electrical data
4.1 DC Characteristics
Maximum DC voltage 40 V
Maximum DC current 3A
Note 1: Typical value is defined as the measured worst case value over 90%
of the frequency band of interest, at room temperature on an average unit
regarding this parameter.
Note 2: Worst case value is defined as the guaranteed worst value on any
unit at any temperature and over the whole frequency band of interest.
Worst Case
Frequency band 1.7-2.5 MHz 2.5 -12.0 MHz
Insertion loss 0.035 dB 0.1 dB
Return loss 25 dB 18 dB
PRODUCT SPEC.
6 (15)
Prepared (also subject responsible if other) No.
The product withstands simultaneous average 500W power at high and low
band ports.
LOW port
IM Product
Worst Case
IM3 -116.5 dBm
IM5 -121.5 dBm
IM7 -121.5 dBm
Note: The average group delay is measured over 4 MHz bandwidth centered
around the frequency given in the table.
PRODUCT SPEC.
8 (15)
Prepared (also subject responsible if other) No.
Note: The average group delay is measured over 4 MHz bandwidth centered
around the frequency given in the table.
PRODUCT SPEC.
9 (15)
Prepared (also subject responsible if other) No.
Note: The average group delay is measured over 4 MHz bandwidth centered
around the frequency given in the table.
PRODUCT SPEC.
10 (15)
Prepared (also subject responsible if other) No.
Note: The average group delay is measured over 4 MHz bandwidth centered
around the frequency given in the table.
PRODUCT SPEC.
11 (15)
Prepared (also subject responsible if other) No.
5 Mechanical Specification
5.1 Weight
5.3 Dimensions
276 x 78 mm (L x W)
PRODUCT SPEC.
12 (15)
Prepared (also subject responsible if other) No.
[SINGLE UNIT]
[DOUBLE UNIT]
PRODUCT SPEC.
13 (15)
Prepared (also subject responsible if other) No.
[SINGLE UNIT]
PRODUCT SPEC.
14 (15)
Prepared (also subject responsible if other) No.
[DOUBLE UNIT]
PRODUCT SPEC.
15 (15)
Prepared (also subject responsible if other) No.
6 Requirement fulfilment
Requirement In 1301-
[RS_DPX301:A_048] Group Delay Ch. 4.6
[SR_GDR:A_044] Wind Load Ch. 5.2
This product fulfills all of the requirements in 1056 – KRF 102 299, except the
exemptions listed below.
Requirement Exemption