Professional Documents
Culture Documents
Page 1 of 6
PROJECT DEVELOPMENT
Version: 2
Approval Date: 04 Nov 2022
DEPARTMENT
Review Cycle: 2 years
Author: Sr. Eng - E&I
[Type
AuthorPosID: here]
PRD1514 CABLE POWER AND CONTROL
Approval: Chief Engineering
ApprovalPosID: PRD1502 LOW VOLTAGE
SPECIFICATION
This document has been revised as indicated below and described in the sign-off legend. Please replace all
pages of this document and destroy the superseded copies.
2 KH KH KH NDP CHT
30/01/21 Update 30/1/21 30/1/21
30/1/21 30/1/21 30/1/21
CHK'
REV DATE DESCRIPTION BY LEAD ENGR PROJ CLIENT
D
ENGR MGR MGR
1.0 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 3
2.0 PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.0 EXECUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 5
4.0 ATTACHMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Summary
A. Scope of Specification
This specification prescribes the general requirements for multiconductor 600 volt power
cables. Refer to 600 Volt Power Cable Datasheets for specific requirements.
B. Related Requirements
Refer to the Request for Quotation or Purchase Order for a listing of related documents
such as datasheets and cable descriptions.
1.2 References
The publications listed below form part of this specification. Each publication shall be the latest
revision and addendum in effect on the date this specification is issued for construction unless
noted otherwise. Except as modified by the requirements specified herein or the details of the
drawings, work included in this specification shall conform to the applicable provisions of these
publications.
I. UL (Underwriter’s Laboratories)
L. Whenever equipment, proposed by the supplier, cannot fully meet the requirements of this
specification, such exceptions must be clearly stated by the supplier. No exceptions shall
be allowed unless approved by Buyer in writing.
2.0 PRODUCTS
2.1 General
2.2 Equipment
A. Conductors
Conductors shall be annealed uncoated copper with class B stranding and shall be sized as
indicated on the datasheets.
B. Insulation
C. Metallic Sheath
D. Fillers
Fillers shall be used as necessary to give the completed cable a substantially circular cross-
section. Fillers shall be of an inert, flame retardant nonhygroscopic material.
F. Jacket
As specified on the datasheets, a jacket of moisture resistant flame retardant and sunlight
resistant material shall be applied over the entire cable assembly.
Testing shall be performed per standards UL 1277 (Power & Control) and UL 83 (Lighting). In
addition, an entire cable assembly sample of all power and control cables shall be subject to a
flame test in accordance with IEEE 383, 70,000 BTU. Representative samples from all cable
types specified shall be used to perform this test (i.e. not on a production run frequency).
A. Power Conductors
Single conductor cable shall have all black XHHW, VW1 insulation. 250K CM and larger
shall be TC rated. Multiconductor power cables shall have all black XHHW, VW1
insulation with printed numbers per ICEA paragraph K.3.A Method 4.
B. Control Conductors
Multiconductor control cables shall have base colored conductor XHHW, VW1 insulation
with tracers per ICEA Table K-2 Method 1.
C. Lighting Conductors
Single conductor cable shall have color coded THHN/THWN insulation per Indonesian
National Standard SNI225-1987.
D. Jacket
The following minimum information shall be printed on the surface of the jacket at regular
intervals:
E. Reels
A bar coded label and a metal weatherproof tag shall be affixed to each side of the reel
indicating the following information:
The bar coded label shall conform to the Bar Code Standard, form number BC-ELEC-
REQ, attached to the Purchase Action Request - Quotation, by Procurement.
Reels shall be lagged or covered with suitable material and strapped to protect the cable from
damage during transit, outdoor storage, and handling. Each end of the cable shall be provided
with a watertight seal.
3.0 EXECUTION
Not applicable.
4.0 ATTACHMENTS
Attachment 01: Form 000.265.F5001 - Manufacturer Datasheet - Cable - Power - Low Voltage
End of Specification
NOTE: This form is to be completed by the Manufacturer and returned with Quotation. Refer to specification S-SP-
4399-65-028 for general requirements.
Manufacturer Supplier
Conductor Material/Stranding
Insulation Type/Thickness
Jacket Type/Thickness
Sheath Type/Thickness
Ampacity at 30C