Professional Documents
Culture Documents
SB MANDATORY 53-1299-01
** ON A/C 3586, 3588-3590, 3595, 3604, 3608, 3614, 3615, 3620, 3632, 3634, 3638, 3647, 3651, 3657,
3660, 3661, 3663, 3671, 3675, 3680, 3683-3687, 3689, 3691, 3694, 3700, 3702, 3704, 3705, 3710, 3720,
3727, 3728, 3733, 3735, 3742, 3744, 3746, 3754, 3757, 3759, 3763, 3768, 3770, 3772, 3774, 3775, 3779,
3788, 3790, 3794, 3797, 3799, 3801, 3803, 3808, 3810, 3818, 3822, 3824, 3826, 3828, 3832, 3834, 3836,
3838, 3839, 3841, 3842, 3844, 3845, 3849, 3851-4329, 4331-5294, 5296-6051, 6053-6061, 6063-6072,
6074-6100, 6102-6115, 6117-6126, 6128-6135, 6138-6141, 6143, 6145-6150, 6152, 6154, 6156, 6157,
6159, 6161, 6162
FRONT MATTER
MODIFICATIONS
None
No additional work is required by this revision for aircraft inspected by any previous issue.
(2) REASON
— Update the Service Bulletin effectivity to remove MSN's 5295 and 4330
— Update APPENDIX 01
(3) CHANGES
HIGHLIGHTS
FRONT MATTER
SUMMARY
PLANNING INFORMATION
EFFECTIVITY UPDATED
Operational/Mainten- OPERATIONAL/MAINTENANCE CONSEQUENCES UPDATED R
ance Consequences EFFECTIVITY UPDATED
DESCRIPTION DESCRIPTION UPDATED R
COMPLIANCE
Classification CLASSIFICATION UPDATED R
EFFECTIVITY UPDATED
Accomplishment ACCOMPLISHMENT TIMESCALE UPDATED R
Timescale EFFECTIVITY UPDATED
APPROVAL
APPROVAL APPROVAL UPDATED R
EFFECTIVITY UPDATED
MANPOWER
MANPOWER MANPOWER UPDATED R
EFFECTIVITY UPDATED
REFERENCES
REFERENCES REFERENCED DOCUMENTATION UPDATED R
EFFECTIVITY UPDATED
MATERIAL INFORMATION
ACCOMPLISHMENT INSTRUCTIONS
EFFECTIVITY UPDATED
Fig. A-GX- SHEET UPDATED R
AAA Sheet 03
Fig. A-GX- SHEET UPDATED R
AAA Sheet 07
Fig. A-GX- SHEET UPDATED R
AAA Sheet 08
Fig. A-GX- SHEET UPDATED R
AAA Sheet 09
Fig. A-GX- SHEET UPDATED R
AAA Sheet 10
Fig. A-GX- SHEET UPDATED R
AAA Sheet 11
The Main Changes are:
— Update the Service Bulletin effectivity to remove MSN's 5295 and 4330 as MSN 5295 had
a QSR done prior to entry into service and MSN 4330 is written off
— Update the address and parameters in the Inspection Report (Figure A-GRAAA)
— Update the address and parameters in the Inspection Report (Figure A-GRAAA)
— Incorporate the validation report findings after accomplishment of this Service Bulletin on
aircraft with Manufacturer Serial Number (MSN) 3882.
This Service Bulletin has been generated electronically and is reissued as a complete docu-
ment. Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
No previous revision
NOTE: Only the aircraft identified by an Airbus Manufacturer Serial Number(MSN) in the ta-
ble are covered in this document.
The following information is provided for each Aircraft:
The Operator/MSN relationship is provided for information only and is correct at the
time of issue in accordance with the information available to AIRBUS. Any future
changes resulting from transfer of an aircraft from one operator to another will not be
reflected in this list unless the Service Bulletin is revised for another reason.
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
AIRBUS quality control identified that items manufactured with wrong aluminum alloy or
wrong heat treatment may have entered the supply chain. Detailed assessment of the im-
pact on aircraft structure of suspected and/or actual non conformance to design definition has
been performed.
The Inspection detailed in this Service Bulletin is focussed on potentially affected structural
parts located in the cargo area.
This Service Bulletin introduces a one time inspection of the potentially affected Part Number
(PN) in the cargo area.
NOTE: Service Bulletins (SBs) for the inspection of parts in the cabin (Service Bulletin No.
A320-53-1298) and flaps (Service Bulletin No. A320-57-1198) have been issued.
The procedure as described in this Service Bulletin is to be performed if no Airbus repair and/
or repair improvement has been previously performed in the same area. In case of repairs
performed previously, please contact AIRBUS Repair Support department for further instruc-
tions.
Accomplishment of this Service Bulletin will allow detection of the affected parts in the cargo
area.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY (1) CANCELS INSPECTION SB NO
POTENTIAL AD YES A/C OPERATION AFFECTED NO
RELIABILITY AF- NO PAX COMFORT AFFECTED NO
FECTED
EVALUATION TABLE
COST SAVING NO ETOPS AFFECTED NO
STRUCTURAL LIFE NO VENDOR SB INVOLVED NO
EXTN
VALIDATION ON AIR- YES BOOKLET AVAILABLE YES
CRAFT
NOTE: This Service Bulletin has been validated at (original issue) on A320 aircraft with
Manufacturer Serial Number (MSN) 3882.
NOTE: A booklet including photographs taken during the validation of this Service Bulletin
is available on AIRBUS|World - Maintenance and Engineering - AirN@v engineering
(in the concerned SB file).
No Material
EFFECTIVITY
CONCURRENT REQUIREMENTS
REFERENCES / REPERCUSSIONS
TFU 53.00.00.015
OEB None
AOT None
SIL None
ISI None
LINE MAINTENANCE AFFECTED No
LIFE LIMIT None
OTHER Operators Information Transmission (OIT) 999.0053/14
AIRCRAFT YES
EQUIPMENT NO
HARD NO
SOFT NO
OBRM NO
MANPOWER
APPENDICES
Appendix 01 - Assessment for Wrong Material Using Eddy Current Conductivity Measurement
(COT) on aluminum Alloys
Appendix 02 - Replacement Part Numbers
Appendix 03 - Effectivity by Part Number
B
Z310
FR77
Z150
FR70
FR60
STGR39RH
STGR41RH
FR54
N_SB_531299_6_SAAA_01_00
1. PLANNING INFORMATION
A. EFFECTIVITY
CONFIGURATION DEFINITION
Config. 001 is applicable to all aircraft listed in the effectivity of this Service Bulletin. For the specif-
ic part numbers to inspect for each MSN, refer to Appendix 03 - Effectivity by Part Number.
Conf.
001
B. CONCURRENT REQUIREMENTS
C. REASON
(1) HISTORY
AIRBUS quality control identified that items manufactured with wrong aluminum alloy or
wrong heat treatment may have entered the supply chain. Detailed assessment of the im-
pact on aircraft structure of suspected and/or actual non conformance to design definition has
been performed.
(2) OBJECTIVE/ACTION
The Inspection detailed in this Service Bulletin is focussed on potentially affected structural
parts located in the cargo area.
This Service Bulletin introduces a one time inspection of the potentially affected Part Number
(PN) in the cargo area.
NOTE: Service Bulletins (SBs) for the inspection of parts in the cabin (Service Bulletin No.
A320-53-1298) and flaps (Service Bulletin No. A320-57-1198) have been issued.
The procedure as described in this Service Bulletin is to be performed if no Airbus repair and/
or repair improvement has been previously performed in the same area. In case of repairs
performed previously, please contact AIRBUS Repair Support department for further instruc-
tions.
(3) ADVANTAGES
Accomplishment of this Service Bulletin will allow detection of the affected parts in the cargo
area.
None
D. DESCRIPTION
E. COMPLIANCE
(1) CLASSIFICATION
This Service Bulletin has been classified Mandatory by the issue of an Airworthiness Direct-
ive (AD) published by the European Aviation Safety Agency (EASA). The AD must be used as
the reference document for the mandated accomplishment timescale.
Table 1. Config. 001 Inspection of Cargo Parts following material Non Conformity
Condition Action Compliance time Repetitive interval
All aircraft Inspect for material non Before 17-Nov-2021, but None
conformity not exceeding 12 years
since the aircraft date of
manufacture.
F. APPROVAL
The technical content of this document is approved under the authority of Design Organisa-
tion Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of AIR-
BUS origin, and which affects the content of this Service Bulletin, the operator is responsible
for obtaining approval by its airworthiness authority for any adaptation necessary before incor-
poration of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator's circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
NOTE: The given Manhours (Total and Elapsed) are for the Inspection only. Manhours to
Get Access and Close-Up are not considered as they are part of the aircraft 6 year
check.
Not Changed
Not Changed
J. REFERENCES
K. PUBLICATION AFFECTED
None
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
2. MATERIAL INFORMATION
MATERIAL EFFECTIVITY
PROCUREMENT ADDRESSES
Customers with aircraft shown in the effectivity of this Service Bulletin should send a purchase
order to AIRBUS. Parts will only be delivered upon findings. The address is:
AIRBUS Material, Logistics and Suppliers
IFD - In Flight Desk
Weg beim Jaeger 150
D-22335 HAMBURG
GERMANY
For ordering by internet: http://spares.airbus.com
For ordering by fax: +49 40 50 76 40 12
For ordering by E-mail: ifd.spares@airbus.com
AIRBUS will credit the manhours indicated in this Service Bulletin at the agreed in-house war-
ranty labor rate for claims received not later than 90 days after completion of the last affected
aircraft of your fleet.
For aircraft with findings further to inspection as per this Service Bulletin, Airbus will provide
the parts at no charge.
AIRBUS will credit the manhours for parts replacement at the agreed in-house warranty labor
rate for claims received not later than 90 days after completion of the last affected aircraft of
your fleet.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organisation of this retrofit, you are kindly requested to contact AIRBUS retrofit man-
agement department.
AIRBUS CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
E-mail : monitored.retrofit@airbus.com
TOOLING
TOOLS
To accomplish this Service Bulletin it is necessary to use the tools listed in Appendix 01 - As-
sessment for Wrong Material Using Eddy Current Conductivity Measurement (COT) on alu-
minum Alloys.
3. ACCOMPLISHMENT INSTRUCTIONS
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAU-
TIONS INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words 'refer
to' are used and the operator has a procedure accepted by the local authority he be-
longs to, the accepted alternative procedure can be used. When the words 'in ac-
cordance with' are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up
steps to add flexibility to their maintenance operations as long as the technical intent
of the Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE: The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance neces-
sary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval.
A. GENERAL
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
06-31-53, Page Block 001
(a) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(b) For Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(2) Subtask 531299-839-201-001 - Administrative
Manpower Resources
Skills NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this Service
Bulletin.
B. PREPARATION
Manpower Resources
Skills AIRFRAME
References
Aircraft Maintenance Manual (AMM) 06-41-00, Page Block 001
Task 12-34-24-869-002
NOTE: The items given in this note shall be considered as the basic Aircraft configuration
before you start a maintenance task:
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task 12-34-24-869-002.
(b) Put an access platform in position below the cargo compartment doors.
(c) Open the cargo compartment doors, refer to AMM 06-41-00, Page Block 001.
(d) Put an access platform in position below the tail section, aft of the pressure bulkhead.
(e) Open the accessory compartment access door 312AR.
C. PROCEDURE
Manpower Resources
Man-hours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON DESTRUCTIVE TESTING
References
Structural Repair Manual (SRM) 51-72-11
Fig. A-GFAAA Sheet 01- Inspection Flowchart
Sheet 02- Inspection Flowchart
Fig. A-GRAAA Sheet 01- Reporting Sheet
Sheet 02- Reporting Sheet
Fig. A-GCAAA Sheet 01- Do an Eddy Current Conductivity Meas-
urement at FR59 to FR60 between STGR39RH and
STGR41RH
YES MATERIAL NO
CORRECT
REPLACE PART
BEFORE NEXT FLIGHT
CLOSE UP AREA
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
NOTE:
SEE SHEET 2 FOR INSPECTION METHOD AND DETAILS
CALCULATE DIFFERENCE
= - = MS/m OR % IACS
< 1MS/m
OR 1.7% IACS YES
01
NO
NO
CORRECT MATERIAL
NOTE:
01 A POSITIVE OR A NEGATIVE VALUE CAN BE THE RESULT OF THE CALCULATION.
CONVERSION OF CONDUCTIVITY VALUES - % IACS (MS/m) REFER TO APPENDIX 01.
N_SB_531299_6_FAAA_02_05
INSPECTION REPORT
SERVICE BULLETIN No.: A320-53-1299
A/C MSN:
RETURN TO:
FLIGHT CYCLES: AIRBUS
FLIGHT HOURS: CUSTOMER SERVICE ENGINEERING
DOORS - FUSELAGE - CWB - WINDOWS
FINDINGS: YES (REPLACE PART) NO ACTION 1 ROND POINT MAURICE BELLONTE
DATE OF INSPECTION: 31707 BLAGNAC CEDEX
FRANCE
PLACE OF INSPECTION: FAX +33 (0)5 61 93 36 14
INSPECTOR: E-mail: inspection.results@airbus.com
AMBIENT TEMPERATURE:
COT WITH 480 kHz CALCULATE
COT WITH 60 kHz REPLACE
480=...[MS/m], IF 60 >20 MS/m DIFFERENCE NO ACTION
ITEM PART NUMBER ZONE/LOCATION 60 [MS/m] PART
OR 34.5% IACS = 480 - 60
REFER TO INSPECTION FLOWCHART
1 D535-70206-200-00 FR70, Z310 (REFER TO FIG A-GBAAA)
N_SB_531299_6_RAAA_02_05
A B
FR60
Z150
STGR39RH
STGR41RH
FR54 A
C
FR60
FR59
B
STGR39RH FR55A
STGR41RH FR54
19
FR60
STGR41RH
C
FR59
N_SB_531299_6_CAAA_01_00
(a) Do the Eddy Current Conductivity Measurement of the installed structural parts in the in-
volved areas, refer to Fig. A-GFAAA Sheet 01, Fig. A-GFAAA Sheet 02, Fig. A-GRAAA
Sheet 01, Fig. A-GRAAA Sheet 02, Fig. A-GCAAA Sheet 01, Appendix 01 - Assessment
for Wrong Material Using Eddy Current Conductivity Measurement (COT) on aluminum
Alloys, Appendix 02 - Replacement Part Numbers and Appendix 03 - Effectivity by Part
Number.
NOTE: The inspection requires direct access to a flat area of the part with a probe.
NOTE: It is not necessary to remove the surface protection to do the conductivity test.
Manpower Resources
Man-hours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON DESTRUCTIVE TESTING
References
Structural Repair Manual (SRM) 51-72-11
Fig. A-GBAAA Sheet 01- Do an Eddy Current Conductivity Meas-
urement at FR70
Fig. A-GFAAA Sheet 01- Inspection Flowchart
Sheet 02- Inspection Flowchart
Fig. A-GRAAA Sheet 01- Reporting Sheet
Sheet 02- Reporting Sheet
Z310
A B FR77
A
FR70
1
C D
FR70
D
VIEW LOOKING FORWARD
AREA FOR INSPECTION
N_SB_531299_6_BAAA_01_03
(a) Do the Eddy Current Conductivity Measurement of the installed structural parts in the in-
volved areas, refer to Fig. A-GFAAA Sheet 01, Fig. A-GFAAA Sheet 02, Fig. A-GRAAA
Sheet 01, Fig. A-GRAAA Sheet 02, Fig. A-GBAAA Sheet 01, Appendix 01 - Assessment
for Wrong Material Using Eddy Current Conductivity Measurement (COT) on aluminum
Alloys, Appendix 02 - Replacement Part Numbers and Appendix 03 - Effectivity by Part
Number.
NOTE: The inspection requires direct access to a flat area of the part with a probe.
NOTE: It is not necessary to remove the surface protection to do the conductivity test.
Manpower Resources
Man-hours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON DESTRUCTIVE TESTING
References
Structural Repair Manual (SRM) 51-72-11
Fig. A-GDAAA Sheet 01- Do an Eddy Current Conductivity
Measurement at FR79 between STGR7LH and
STGR7RH
Fig. A-GFAAA Sheet 01- Inspection Flowchart
References
Sheet 02- Inspection Flowchart
Fig. A-GRAAA Sheet 01- Reporting Sheet
Sheet 02- Reporting Sheet
FR86
Z310
A FR84
A
FR79
FR79
FR78
STGR1
STGR7RH
20
STGR7LH
N_SB_531299_6_DAAA_01_00
(a) Do the Eddy Current Conductivity Measurement of the installed structural parts in the in-
volved areas, refer to Fig. A-GFAAA Sheet 01, Fig. A-GFAAA Sheet 02, Fig. A-GRAAA
Sheet 01, Fig. A-GRAAA Sheet 02, Fig. A-GDAAA Sheet 01, Appendix 01 - Assessment
for Wrong Material Using Eddy Current Conductivity Measurement (COT) on aluminum
Alloys, Appendix 02 - Replacement Part Numbers and Appendix 03 - Effectivity by Part
Number.
NOTE: The inspection requires direct access to a flat area of the part with a probe.
NOTE: It is not necessary to remove the surface protection to do the conductivity test.
Manpower Resources
Man-hours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON DESTRUCTIVE TESTING
References
Structural Repair Manual (SRM) 51-72-11
Fig. A-GEAAA Sheet 01- Do an Eddy Current Conductivity Meas-
urement at FR80
Fig. A-GFAAA Sheet 01- Inspection Flowchart
Sheet 02- Inspection Flowchart
References
Fig. A-GRAAA Sheet 01- Reporting Sheet
Sheet 02- Reporting Sheet
B
Z310 FR86
A FR84
FR80 A
FR78
STGR6LH
STGR6RH
STGR15LH 21
22
FR80 STGR15RH
23
B
N_SB_531299_6_EAAA_01_00
(a) Do the Eddy Current Conductivity Measurement of the installed structural parts in the in-
volved areas, refer to Fig. A-GFAAA Sheet 01, Fig. A-GFAAA Sheet 02, Fig. A-GRAAA
Sheet 01, Fig. A-GRAAA Sheet 02, Fig. A-GEAAA Sheet 01, Appendix 01 - Assessment
for Wrong Material Using Eddy Current Conductivity Measurement (COT) on aluminum
Alloys, Appendix 02 - Replacement Part Numbers and Appendix 03 - Effectivity by Part
Number.
NOTE: The inspection requires direct access to a flat area of the part with a probe.
NOTE: It is not necessary to remove the surface protection to do the conductivity test.
D. TEST
NOTE: None
E. CLOSE-UP
Manpower Resources
Skills AIRFRAME
(a) Make sure that the work areas are clean and clear of tools and other items of equipment.
(b) Remove the access platforms.
(c) Put the aircraft back to its initial configuration.
GRAPHIC
GRAPHIC
Inspection Flowchart
YES MATERIAL NO
CORRECT
REPLACE PART
BEFORE NEXT FLIGHT
CLOSE UP AREA
NO FURTHER ACTION
IN ACCORDANCE WITH
THIS SERVICE BULLETIN
NOTE:
SEE SHEET 2 FOR INSPECTION METHOD AND DETAILS
CALCULATE DIFFERENCE
= - = MS/m OR % IACS
< 1MS/m
OR 1.7% IACS YES
01
NO
NO
CORRECT MATERIAL
NOTE:
01 A POSITIVE OR A NEGATIVE VALUE CAN BE THE RESULT OF THE CALCULATION.
CONVERSION OF CONDUCTIVITY VALUES - % IACS (MS/m) REFER TO APPENDIX 01.
N_SB_531299_6_FAAA_02_05
GRAPHIC
GRAPHIC
Do an Eddy Current Conductivity Measurement at FR59 to FR60 between STGR39RH and STGR41RH
A B
FR60
Z150
STGR39RH
STGR41RH
FR54 A
C
FR60
FR59
B
STGR39RH FR55A
STGR41RH FR54
19
FR60
STGR41RH
C
FR59
N_SB_531299_6_CAAA_01_00
GRAPHIC
GRAPHIC
Do an Eddy Current Conductivity Measurement at FR70
Z310
A B FR77
A
FR70
1
C D
FR70
D
VIEW LOOKING FORWARD
AREA FOR INSPECTION
N_SB_531299_6_BAAA_01_03
GRAPHIC
GRAPHIC
Do an Eddy Current Conductivity Measurement at FR79 between STGR7LH and STGR7RH
FR86
Z310
A FR84
A
FR79
FR79
FR78
STGR1
STGR7RH
20
STGR7LH
N_SB_531299_6_DAAA_01_00
GRAPHIC
GRAPHIC
Do an Eddy Current Conductivity Measurement at FR80
B
Z310 FR86
A FR84
FR80 A
FR78
STGR6LH
STGR6RH
STGR15LH 21
22
FR80 STGR15RH
23
B
N_SB_531299_6_EAAA_01_00
GRAPHIC
GRAPHIC
Reporting Sheet
INSPECTION REPORT
SERVICE BULLETIN No.: A320-53-1299
A/C MSN:
RETURN TO:
FLIGHT CYCLES: AIRBUS
FLIGHT HOURS: CUSTOMER SERVICE ENGINEERING
DOORS - FUSELAGE - CWB - WINDOWS
FINDINGS: YES (REPLACE PART) NO ACTION 1 ROND POINT MAURICE BELLONTE
DATE OF INSPECTION: 31707 BLAGNAC CEDEX
FRANCE
PLACE OF INSPECTION: FAX +33 (0)5 61 93 36 14
INSPECTOR: E-mail: inspection.results@airbus.com
AMBIENT TEMPERATURE:
COT WITH 480 kHz CALCULATE
COT WITH 60 kHz REPLACE
480=...[MS/m], IF 60 >20 MS/m DIFFERENCE NO ACTION
ITEM PART NUMBER ZONE/LOCATION 60 [MS/m] PART
OR 34.5% IACS = 480 - 60
REFER TO INSPECTION FLOWCHART
1 D535-70206-200-00 FR70, Z310 (REFER TO FIG A-GBAAA)
N_SB_531299_6_RAAA_02_05
A. Assessment for Wrong Material Using Eddy Current Conductivity Measurement (COT) on
aluminum Alloys.
Assessment for Wrong Material Using Eddy Current Con-
ductivity Measurement (COT) on aluminum Alloys
N_SB_531299_6_AAAA_01_03
N_SB_531299_6_AAAA_02_02
N_SB_531299_6_AAAA_03_02
N_SB_531299_6_AAAA_04_02
N_SB_531299_6_AAAA_05_02
N_SB_531299_6_AAAA_06_02
A.
Part Number to be Inspected Part Number to be Ordered for Replacement
D5357020620000 D5357020620051
D5358526421200 D5358526421251
D5358526421400 D5358526421400
D5358526421000 D5358526421051
D5358513120001 D5358513120051
D5347717620000 D5347717620051
A. The table that follows gives the list of applicable MSNs and shows which part numbers
are effected.
Effectivity by Part Number
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_01_01
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
N_SB_531299_6_XAAA_02_01
D5347717620000
Effectivity by Part Number
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_03_02
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_04_01
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_05_01
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_06_01
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_07_02
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_08_02
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_09_02
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN MSN MSN MSN MSN MSN
N_SB_531299_6_XAAA_10_02
D5347717620000
D5357020620000
D5358513120001
D5358526421000
D5358526421200
D5358526421400
MSN
6120 X X
6121 X X
6122 X X
6123 X X
6124 X X
6125 X X
6126 X X
6128 X X
6129 X X
6130 X X
6131 X X
6132 X X
6133 X X
6134 X X
6135 X X
6138 X X
6139 X X
6140 X X
6141 X X
6143 X X
6145 X X
6146 X X
6147 X X
6148 X X
6149 X X
6150 X X
6152 X X
6154 X X
6156 X X
6157 X
6159 X
6161 X
6162 X
N_SB_531299_6_XAAA_11_02
End of document