This document contains 50 multiple choice questions related to oil and gas drilling operations. It provides the questions along with the correct answers. For each question, it indicates whether the user's answer was correct or not. The questions cover topics like mud properties, well design, directional drilling, casing design, cementing, drilling hydraulics and different drilling challenges. The document serves as a knowledge assessment tool to test understanding of key drilling engineering concepts and terminology.
This document contains 50 multiple choice questions related to oil and gas drilling operations. It provides the questions along with the correct answers. For each question, it indicates whether the user's answer was correct or not. The questions cover topics like mud properties, well design, directional drilling, casing design, cementing, drilling hydraulics and different drilling challenges. The document serves as a knowledge assessment tool to test understanding of key drilling engineering concepts and terminology.
This document contains 50 multiple choice questions related to oil and gas drilling operations. It provides the questions along with the correct answers. For each question, it indicates whether the user's answer was correct or not. The questions cover topics like mud properties, well design, directional drilling, casing design, cementing, drilling hydraulics and different drilling challenges. The document serves as a knowledge assessment tool to test understanding of key drilling engineering concepts and terminology.
correct answer Each question carries equal marks and no negative markings. 4.Leak off test was carried out with 10 ppg mud at 10,000 ft shoe depth and leak off pressure is 1,040 psi. Max value of LOT MW is ………….ppgSingle choice. (0/2 Points) 10 12 14 Your answer to question 4 is wrong. Correct answers: 12 5._____________ pressure is caused by weight of rock matrix above.Single choice. (2/2 Points) Formation Overburden Pore Correct answers: Overburden 6._____________ well data is used for designing new well.Single choice. (0/2 Points) Calculated Simulated Offset Your answer to question 6 is wrong. Correct answers: Offset 7.Pressure integrity test (PIT) pressure may be ___________________ LOT pressureSingle choice. (0/2 Points) more than Less than equal to Your answer to question 7 is wrong. Correct answers: Less than 8.Bit HHP for bit pressure loss of 1714 psi and 500 gpm mud discharge is ______________Single choice. (2/2 Points) 500 850 900 Correct answers: 500 9.If hole area in question-5 is 125 sq inch, then HSI (Bit Hydraulic HP per sq inch of hole size) is __________Single choice. (0/2 Points) 4 3 5 Your answer to question 9 is wrong. Correct answers: 4 10.Recommended range of HSI (Bit Hydraulic HP per sq inch of hole size) for a vertical well is_________Single choice. (0/2 Points) 1-2 2-5 6-10 Your answer to question 10 is wrong. Correct answers: 2-5 11.Recommended range of annular velocity for 8.5” hole size is ______________ m/ minuteSingle choice. (2/2 Points) 18-30 21-33 36-54 Correct answers: 36-54 12.Effective length factor is used in ___________________ well for calculating bottoms up strokesSingle choice. (2/2 Points) Inclined Vertical Correct answers: Inclined 13.Recommended GPM (flow rate) for inclined well is ___________________ that for vertical wellSingle choice. (2/2 Points) more than equal to less than Correct answers: more than 14.Out of sand, shale and limestone, _________ is most competent formation for setting casing shoeSingle choice. (0/2 Points) sand shale limestone Your answer to question 14 is wrong. Correct answers: shale 15.For a 0.06 gm/cc kick from 4,000 m depth with mud weight of 1.70 gm/cc in hole, is the casing shoe at 3,000 m with 1.80 MWE fracture strength strong enough and acceptable.Single choice. (0/2 Points) True False Your answer to question 15 is wrong. Correct answers: True 16.The next casing shoe is planned at 3,900 m. When drilling at 3,900 m with 1.67 gm/ cc mud, formation pr at 3,000 m is 1.07 MWE. Is the differential pressure at 3,000 m depth within recommended limit True / FalseSingle choice. (0/2 Points) True False Your answer to question 16 is wrong. Correct answers: False 17.With surge and swab consideration of 0.04 gm/ cc, minimum MW required to drill formation with 1.30 gm/ cc MWE pore pressure is ___________ gm/ ccSingle choice. (0/2 Points) 1.35 1.38 1.40 Your answer to question 17 is wrong. Correct answers: 1.38 18.Resultant burst pressure for casing design is maximum at _________________ of the holeSingle choice. (0/2 Points) top bottom middle Your answer to question 18 is wrong. Correct answers: top 19.Resultant Collapse pressure for casing design is maximum at_____________the holeSingle choice. (2/2 Points) top middle bottom Correct answers: bottom 20.Due to biaxial load, collapse resistance______________Single choice. (2/2 Points) increases decreases Correct answers: decreases 21.Buoyancy factor for 1.57 gm/cc mud weight is ________Single choice. (0/2 Points) 0.7 0.9 0.8 Your answer to question 21 is wrong. Correct answers: 0.8 22.Please fill the correct values of safety factors are used in O.N.G.C. for casing design for burstSingle choice. (0/2 Points) 0.85-1.125 1.10-1.125 1.8-1.6 Your answer to question 22 is wrong. Correct answers: 1.10-1.125 23.Please fill the correct values of safety factors are used in O.N.G.C. for casing design for collapse : ________ (cemented portion) and __________ (uncemented portion)Single choice. (2/2 Points) 0.85-1.125 1.10-1.125 1.8-1.6 Correct answers: 0.85-1.125 24.Please fill the correct values of safety factors are used in O.N.G.C. for casing design for tension_________(without buoyancy) and ______ ( with buoyancy)Single choice. (0/2 Points) 0.85-1.125 1.10-1.125 1.8-1.6 Your answer to question 24 is wrong. Correct answers: 1.8-1.6 25.In a directional well 23. Build, hold and drop is ____________ type of profileSingle choice. (-/2 Points) L J S 26.Multi lobe motor gives _______________ flow area .Single choice. (0/2 Points) reduced increaswed Your answer to question 26 is wrong. Correct answers: reduced 27.Multi lobe motors are ____________ motorsSingle choice. (0/2 Points) low torque high torque Your answer to question 27 is wrong. Correct answers: high torque 28.2 to 8 degree/ 100 ft build up will result in _______________radius wellSingle choice. (0/2 Points) long intermediate short Your answer to question 28 is wrong. Correct answers: long 29.The correct value of B.S.R (Bending strength ratio) between two sections of tubulars for normal condition is more than or equal toSingle choice. (0/2 Points) 2.5 3.5 4.5 6.5 5.5 Your answer to question 29 is wrong. Correct answers: 5.5 30.The correct value of B.S.R (Bending strength ratio) between two sections of tubulars for severe condition and high failure rate is more than or equal toSingle choice. (0/2 Points) 2.5 3.5 4.5 6.5 5.5 Your answer to question 30 is wrong. Correct answers: 3.5 31.5” 19.5 ppf E, G and S grade drill pipe have _______________ connectionSingle choice. (0/2 Points) NC 26 NC 38 NC 50 Your answer to question 31 is wrong. Correct answers: NC 50 32.Back up pressure at top for resultant burst pressure for casing design is ________Single choice. (2/2 Points) Zero Maximum Correct answers: Zero 33.Data about _________ strength of formation is needed for designing bits suited for particular formationsSingle choice. (2/2 Points) compressive tensile Correct answers: compressive 34.Formation with compressive strength of 6000 to 9000 psi are classified as ___________ formationsSingle choice. (0/2 Points) soft medium hard Your answer to question 34 is wrong. Correct answers: soft 35.___________, ____________ and ___________ logs help in determining compressive strength of formationMultiple choice. (0/4 Points) Resistivity sonic Gama density Caliper Your answer to question 35 is wrong. Correct answers: sonic,Gama,density 36.In recent past, _________well drilled by ONGC in Frontier basin had formation of very high compressive strength at shallow depthSingle choice. (0/2 Points) Jabera Rewa Gwalior Your answer to question 36 is wrong. Correct answers: Jabera 37.Stuck pipe is No- 1 well complication problem. ____________________ and _____________________ are next major complications.Multiple choice. (0/2 Points) logging tool stuck string failure bit failure well activity Your answer to question 37 is wrong. Correct answers: string failure,well activity 38.If mud weight is required to be increased, it should be increased ____________________Single choice. (2/2 Points) in increments of 0.1 ppg in increments of 0.5 ppg at one go Correct answers: in increments of 0.1 ppg 39.One of the major causes for blow out on Deep Water Horizon rig in Gulf of Mexico in April 2010 was installing insufficient number of centralizers run on casing.Single choice. (2/2 Points) True False Correct answers: True 40.Metal petal basket helps in _____________________ of casing during cementationSingle choice. (-/2 Points) rotation reciprocation 41.Approximate cost of neat cement is ____________ per MTSingle choice. (2/2 Points) Rs 10,000 Rs 20,000 Rs 30,000 Correct answers: Rs 10,000 42.Approximate cost of gas tight cement slurry is Rs ____________ per cu MSingle choice. (2/2 Points) 23,000 53,000 93,000 Correct answers: 53,000 43.Due to very less clearance between casing and open hole, __________ problem is experienced some time during hole conditioning before cement jobSingle choice. (2/2 Points) stuck pipe mud loss Correct answers: mud loss 44.USIT logging tool is used to evaluate cement bond. Please write the full name of the toolSingle choice. (2/2 Points) Ultra sonic imaging tool Ultra short imaging tool Correct answers: Ultra sonic imaging tool 45.At deeper depth, bit hydraulics is designed by :Single choice. (0/2 Points) Max bit impact theory Max Bit HHP theory Your answer to question 45 is wrong. Correct answers: Max bit impact theory 46.In ____________ area of ONGC, the dip angles of formations are very high reaching to 80-85 degreesSingle choice. (0/2 Points) Gandhar Silchar Agartala Gelekey Your answer to question 46 is wrong. Correct answers: Silchar 47.In deep water wells, there is very narrow window between pore pressure and _______Single choice. (2/2 Points) overburden pressure formation fracture pressure mud hydrostatic pressure formation pressure Correct answers: formation fracture pressure 48.Insitu combustion is used to recover thick (highly viscous crude oil) in ____________ asset of ONGCSingle choice. (2/2 Points) CBM Mehsana Ankleshwar Correct answers: Mehsana 49.Bi-centre bit drills _________ hole below the casingSingle choice. (2/2 Points) larger smaller same diameter Correct answers: larger 50.Chrome casing is used in wells where ____________ and ___________ gases are also present with crude oilMultiple choice. (0/2 Points) Hydrogen sulphide carbon di oxide Methane Carbon monoxide Your answer to question 50 is wrong. Correct answers: Hydrogen sulphide,carbon di oxide 51.Inhibitive mud system is used for drilling____________Single choice. (-/2 Points) reactive clay fractured shale 52.Well design should never be changed once approved even if problems are faced.Single choice. (-/2 Points) True False