Professional Documents
Culture Documents
SNO-I-DS-004
ORIFICE PLATE REV. C1 Page 2 of 72
SENORO GAS DEVELOPMENT PROJECT DATE. 07-Nov-13
REVISION REVISION
SHEET SHEET
B C C1 B C C1
1 X X X 34 X X X
2 X X X 35 X X X
3 X X X 36 X X X
4 X X X 37 X X X
5 X X X 38 X X X
6 X X X 39 X X X
7 X X X 40 X X X
8 X X X 41 X X X
9 X X X 42 X X X
10 X X X 43 X X X
11 X X X 44 X X X
12 X X X 45 X X X
13 X X X 46 X X X
14 X X X 47 X X X
15 X X X 48 X X X
16 X X X 49 X X X
17 X X X 50 X X X
18 X X X 51 X X X
19 X X X 52 X X X
20 X X X 53 X X X
21 X X X 54 X X
22 X X X 55 X X
23 X X X 56 X X
24 X X X 57 X X
25 X X X 58 X X
26 X X X 59 X X
27 X X X 60 X X
28 X X X 61 X X
29 X X X 62 X X
30 X X X 63 X X
31 X X X 64 X X
32 X X X 65 X X
33 X X X 66 X X
67 X X
68 X X
69 X
70 X
71 X
72 X
INSTRUMENT DATA SHEET FOR Doc. No. SNO-I-DS-004
ORIFICE PLATE REV. C1 Page 3 of 72
SENORO GAS DEVELOPMENT PROJECT DATE. 07-Nov-13
REVISION SUMMARY
FE-9054-C is deleted
Tag no. is corrected
Line item no.9. Flowrate unit changed to usgpm for liquid fluid.
Line item no. 39. Flanged tap shall be applied for the line size above 14” as
per vendor recommendation and ISO standard.
Line item no. 40. Tap orientation for liquid fluid corrected to 45 Deg Down.
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 8.6 / -
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing repo
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 23.51 / -
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing repo
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 23.4 / -
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing repo
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 12.4 / -
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing repo
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 23.6 / -
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut UNS S31803
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing repo
9. Liquid Contents
- Condensate / Water Max. Flowrate [Usgpm] : 117.8 / 0.038
- Condensate / Water Density [lb/ft3] : 41.37 / 61.30
- Condensate / Water Viscosity [cP] : 0.301 / 0.455
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x NPT. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x NPT. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x NPT. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x SW. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD RTJ. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M, A194 GR,2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
C1 37 Jak Screw & Plug A105N
38 Nipple A106 GR.B
39 Taps Type Number of Tapping flanged 2(with plug) in each flange
40 Taps Size Tap Orientation 1/2" NPT 45 DEG UP
41 Calculation Note Yes
42
C1 43 Manufacturer Samil
PURCHASE
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 53KA
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOJ-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
C1 36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B8M CL.2 / A194 GR.8M
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7M / A194 GR.2HM
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B16 / A194 GR.4
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x SW. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A320 GR.L7 / A194 GR.7
ORIFICE F
C1 44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
C1 46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x WN. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x FLGD. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x SW. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.
35 Gasket 33FAFF
36 Material (Note 6) Bolt/ Nut A193 GR.B7 / A194 GR.2H
ORIFICE F
44 Model SOP-SOF
45 Requisition Number SNO-I-RQ-013
46 PO No. 4500129520
47
Notes :
1. Orifice Plate shall be sized in accordance with L.K. Spink's "Principle or ISO 5167 & ISO 5168 and Practice of Flow Meter Engineering." 9th edition; and on AGA
report No.3. Flange tap connections shall be in accordance with ASME B16 36.
2. Orifice Plate thickness shall be verified by stress calculation.
3. Beta Ratio shall be between 0.2~0.7. (API RP-550)
4. Meter range shall be used 40,50,60,100,120,200 inch H2O except that, when metering compressible fluids, the meter range in inches of water shall not exceed the
line pressure expressed in psia.
5. Nipple shall be 1/2" NPT x SW. (Bended type)
6. Vendor shall refer to the Specification for piping material class, SNO-P-GS-001 and Standard specification for engineering and design of instrumentation systems,
SNO-I-ES-001 for detail.
7. Tag No, Flange Size & Rating, Bore size and Upstream / Downstream direction shall be stamped on the orifice plate.
8. Vendor shall provide orifice calculation / sizing report.