Professional Documents
Culture Documents
Notes
03/2012
Sample Applications
1Framo 80
Beam Section TP F 80 Cantilever Bracket AK F 80 Beam Bracket TKO F 80
Framo 80 1-1
Framo 80
Page 1-15
03/2012
Framo 80 1-2
Framo 80
Beam Section TP F 80
Group: A410
Application
Multi-function beam profile for horizontal, vertical and 3-D support structures in
a wide variety of building and industrial applications.
In addition to the high torsional resistance achieved using a totally closed
profile, structural elements and pipe supports can be attached on all 4 sides
with virtually no placement restrictions. Specifically designed mounting holes
combined with special FLS Self Forming Screws ensure precise component
placement and secure form-locked mountings.
Technical Data
Type Section modulus Moment of inertia Radius of inertia Torsional Cross section
[in3 ] [in4 ] [in] moment lt A
[in 4 ] [in2 ]
TP F 80 0.97 ly: 1.53 iy: 1.16 2.36 1.13
lz: 1.53 iz: 1.16
Type Section modulus Moment of inertia Radius of inertia Torsional Cross section
[cm3 ] [cm4 ] [cm] moment lt A
[cm 4 ] [cm2 ]
TP F 80 15.87 ly: 63.49 iy: 2.95 98.22 7.28
lz: 63.49 iz: 2.95
For all values the effect of holes and perforations have been taken into account.
Approvals
MPA approved
Framo 80 1-3
Framo 80
Cantilever Bracket AK F 80
Group: A420
Application
Ready-to-use element for mounting to Beam Section F 80 and Beam Bracket
TKO F 80 or for construction of cross bars with respective connecting element.
Version "E" enables construction of a vertically hung Beam Bracket TKO F 80
with a Cantilever Bracket AK F 80 at the lowest point without any overlap of the
mounting plate in the vertical plane.
Configuration
With pre-assembled End Cap ADK F 80
Installation
Interlocking connection to Beam Section F 80 by means of 4 Self Forming
Screws FLS F 80.
Technical Data
Approvals
MPA approved
Framo 80 1-4
Framo 80
Application
Ready-to-use element for mounting to walls, floors, ceilings and also can be
mounted to Simotec Systems 100 and 120 or for assembling crossbars with the
respective connecting element.
Configuration
With pre-assembled End Cap ADK F 80.
Installation
Depending on the situation, different options are recommended:
a) Fixing to building structure using 4 heavy duty anchors 1/2" (M12).
b) Frictional connection to steel beams (flange width 3 1/8" - 4 3/4" / 80 -
120 mm) with Assembly Set P2.
c) Interlocking connection to beams of System 100 or 120 by means of
Bracket Plates FV 100/120.
Technical Data
Approvals
MPA approved
Framo 80 1-5
Framo 80
Application
In connection with Beam Bracket, Cantilever Bracket or Beam Section F 80, the
End Support STA F 80 enables the construction of crossbars and multiple other
constructions.
The Version "A" is specially conceived for direct connection to cast-in channels
built into the building structure.
Installation
STA F 80
Depending on the version, following mountings solutions are possible:
a) Connection to Beam Section F 80 with system elements by means of
4 Self Forming Screws FLS F 80.
b) Screw connection with cast-in channel by means of appropriate
T-head bolt or Channel nut with Hexagon bolt (Type "A").
Technical Data
Approvals
MPA approved
Framo 80 1-6
Framo 80
Application
End Support WBD F 80 is ideal for making supports for wall and floor mounting,
as well as crossbars in conjunction with Beam Section F 80.
Beside the direct connection to building structure, different base plates allow an
immediate connection to various flange widths.
For crossbar constructions, version WBD F 80-T has to be used. The octagonal
connection allows max. use of section width without interfering screws or
plates.
Installation
Depending on the situation, different options are recommended:
a) Fixing to building structure using 4 heavy-duty 1/2" anchors resp. 5/8".
b) Frictional connection to steel beams using Assembly Set P2, P3 or
respective Beam Clip.
c) Form-locking connection to beam systems STF 100 or 120 using
Bracket Plates FV 100/120.
Technical Data
Type for flange width Dimensions of base plate Slots in base plate for
[in] [in] [in]
WBD F 80-80/120 3 1 /8 " - 4 3 /4 " 8 5 /8 " x 8 5 /8 " x 1 /2 " 1
/2 "
WBD F 80-121/160 4 /4" - 6 /4" 14 /16" x 10 1/4" x 1/2"
3 1 3 1
/2 "
WBD F 80-161/200 6 1/4" - 7 7/8" 14 3/16" x 12 1/4" x 1/2" 5
/8 "
WBD F 80-201/300 7 7/8" - 11 3/4" 16 1/2" x 8 5/8" x 1/2" 5
/8 "
WBD F 80-T 3 /8 " - 4 /4 "
1 3
8 5 /8 " x 8 5 /8 " x 1 /2 " 1
/2 "
Type for flange width Dimensions of base plate Slots in base plate for
[mm] [mm]
WBD F 80-80/120 80 - 120 220 x 220 x 12 M12
WBD F 80-121/160 121 - 160 320 x 260 x 12 M12
WBD F 80-161/200 161 - 200 320 x 310 x 12 M16
WBD F 80-201/300 201 - 300 420 x 220 x 12 M16
WBD F 80-T 80 - 120 220 x 220 x 12 M12
Approvals
MPA approved
Framo 80 1-7
Framo 80
Joining Plate AP
Group: A630
Application
Permits the connection of Beam Bracket TKO F 80 to flange widths > 4 3/4", as
well as to building structures by means of heavy load anchors.
Configuration
Joining Plate AP
Assembly Set AP:
4 Countersink Screws 1/2"
4 Hexagon Nuts 1/2"
4 Washers
Installation
1) Interlocking connection of Joining Plate with Beam Bracket TKO F 80 by
means of countersink screws and hexagon nuts.
2a) Fixing to concrete by means of 4 heavy-load anchors 1/2" or 5/8" (from
Type AP 161/200 on).
2b) Frictional connection to steel beams by means of Assembly Set P2 or P3
(from Type AP 161/200 on).
Technical Data
Type for flange width Dimension of base plate Slots in base plate for
[in] [in] [in]
AP 121/160 4 3/4" - 6 5/16" 12 3/5" x 10 1/4" x 1/2" 1
/2 "
AP 161/200 6 5/16" - 7/8" 12 3/5" x 12 1/4" x 1/2" 5
/8 "
AP 201/300 7 /8" - 11 /4" 16 1/2" x 8 11/16" x 1/2"
7 3 5
/8 "
Framo 80 1-8
Framo 80
Application
Element to be used for flexible welding to beams, welding plates or further
suitable weldable connection spots. In connection with Beam Bracket TKO,
Cantilever Bracket AK or Beam Section F 80, the Welding Adapter allows the
construction of crossbars, cantilevers, as well as further construction
possiblities.
Installation
Apply the base plate adapter side to the connecting element and weld on. The
weldable hcp-surface requires an aftertreatment of corrosion protection only at
and around the weld seam. The other native connection with Beam Section F 80
is done by means of 4 Self Forming Screws FLS F 80.
Technical Data
Framo 80 1-9
Framo 80
Channel Adapter SA F 80
Group: A430
Application
Allows the compatibility of 1 - 5/8" framing system (channels 1 5/8" x 1 5/8" or 1
5
/8" x 1 5/8" D) with Beam Section F 80. Simple construction of pipe lines or
constructions, optionally with further parts of the Siconnect System. Thanks to
the Pressix CC-Technology the channel can be connected directly to the
Channel Adapter.
Installation
Interlocking connection to Beam Section F 80 by using 4 Self Forming Screws
FLS F 80.
Technical Data
03/2012
Framo 80 1-10
Framo 80
Application
Threaded Self Forming Screw for formlocking connection of Framo system
components and Siconnect products to Beam Section F 80.
The beam section material is locally cold-hardened due to the non-cutting
forming. The high resulting edge-covering and a threaded connection between
Self Forming Screw and Beam Section prevents from accidental unscrewing.
During assembly process, the special interlocking prevents from overtightening.
Technical Data
Approvals
MPA tested
Framo 80 1-11
Framo 80
Assembly Set P
Group: A640
Application
Element for connecting Beam Bracket TKO, Angled Beam Bracket SKO or End
Support WBD to a beam section.
Configuration
Installation
The narrow ends of the Beam Clips must be fixed to the beam flange.
Max. perm. torque of all 1/2" bolts: 85 Nm / 62 ft/Ibs (Set P2)
Max. perm. torque of all 5/8" bolts: 150 Nm / 110 ft/Ibs (Set P3)
Once post-tensioned, the hexagon bolts must not be re-used!
Up to flange width: 1 5/16"
Technical Data
1 set is required Material: Steel and cast iron, hcp
03/2012
Framo 80 1-12
Framo 80
U-Holder SB F 80
Group: A430
Application
Connecting element for bilateral fixation of Beam Section F 80, crossbars or
cantilevers to steel beams.
Configuration
Type SB F 80-40:
Holder with thread 1/2"
Plate
SB F 80-40
2 Beam Clips P2
2 Hexagon nuts 1/2"
2 Washers
Installation
U-holder to be used in pairs.
Type 40 up to flange width 1 9/16"
Technical Data
Material:
U-Holder Steel, hcp
Plate Steel, hcp
Beam clip Steel resp. Cast Iron, hcp
Nut/Washer Steel, hcp
Framo 80 1-13
Framo 80
Application
All-embracing, stiffening holder for Beam Section F 80
directly on the provided support
directly to free-standing channels or channels set in concrete
directly onto other Beam Section F 80 for frame assembly.
Technical Data
Material: Steel, hcp
03/2012
Framo 80 1-14
Framo 80
Application
End cap for a clean finish of closing the ends of Beam Section F 80, Cantilever
Brackets, as well as Beam Brackets.
Technical Data
Material: PE, yellow
Framo 80 1-15
Framo 80
03/2012
Framo 80 1-16
Supports
4Supports
S
Sliding Support LA - HV Sliding Support LC - HV Sliding Support LD - HV
Approvals
Available on request.
Further informations: www.sikla.us/products/simotec
03/2012
Simotec 2-1
Subassemblies
4Supports
Speed Nut NT CC 41 - for all 1 5/8“ channel profiles, independent of the depth of the channnel
Very useful for retaining the channel nut in place when the application calls for the installation of vertical channels or in
place, which are difficult to access. Further benefits:
Available on request.
Further informations: www.sikla.us/products/simotec
03/2012
Simotec 3-1