Professional Documents
Culture Documents
2013
Pipe Standard - Introduction
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
Table of contents
STD-326-101 Bulk Handling System
STD-351-101 Fuel Oil Cargo System
STD-352-101 Fresh Water Cargo System
STD-353-101 Special Products Cargo System
STD-354-101 Multi-Purpose Special Products Cargo System
STD-355-101 Methanol Cargo System
STD-356-101 Drill Cutting Cargo System
STD-357-101 Mud Cargo System
STD-358-101 Brine Cargo System
STD-359-101 Base Oil Cargo System
STD-382-101 Tank Cleaning System
STD-405-101 Anti-Heeling System
STD-441-101 Acetylen / Oxygen System
STD-444-101 Vacuum Cleaning System
STD-571-101 Chilled Water System
STD-571-102 Air Conditioning System
STD-577-101 Central Heating System
STD-581-101 Sanitary Supply System
STD-582-101 Sanitary Discharge System
STD-641-101 Steam System
STD-701-101 Fuel Oil Transfer & Drain System
STD-701-102 Quick Closing System
STD-703-101 Fuel Oil Supply System
STD-707-101 Gas Fuel System (LNG)
STD-711-101 Lub Oil System incl. Separators
STD-721-101 Sea Water Cooling System
STD-722-101 Fresh Water Cooling System
STD-731-101 Compressed Air System
STD-740-101 Exhaust Gas System
STD-801-101 Water Ballast & Drillwater System
STD-803-101 Bilge System
STD-804-101 Drain System
STD-813-101 Fire Line System
STD-814-101 FiFi, external System
STD-821-101 Tank Vent & Overflow System
STD-822-101 Sounding System
STD-831-101 Special Hydraulic Oil System (Low Pressure )
STD-831-102 Special Hydraulic Oil System (High Pressure )
GENERAL REMARKS:
Pipes on open deck to be hot dip galvanized after prefabrication / prior to installation.
All valves on deck - AISI316 handle and plate
Overboard valves size DN 125 and bigger to have DNV product certificate acc. to DNV 4.6.7 C301.
Connecting sleeves are not allowed on overboard pipes with substantial thickness (DNV 4.6.7 F103)
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Fill / Disch pipes bend radius 5xD. Vent.pipes bends radius 2,5xD.
Pipe cold bending R=1,5xD only for compressed air supply pipes
Pipes to be easily dismountable
Pipe system to comply with requirements in DNV Pt.5, Ch.7, Sec.4B.
Fill / Disch. Stations Cement 5"Fig 50, male end coupling. Color code Yellow. Barite Xover fenmale x female color code Orange
Outlet from safety valves BHS tanks to be min 2000 mm above Mdcek.
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11 and NOFO Standard
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
326 Butterfly Valve, lug DN40-DN600 EGO PN16/PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI316 AlBr NBR -15 +80 EGO 5521362 --> 306-307
326 Butterfly Valve, lug DN40-DN200 EGO PN16/PN10 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 +80 EGO 5521377 --> 306-307
326 Butterfly Valve, lug DN200-DN600 EGO PN10 Ductile iron Type C = Gear operated AISI316 AlBr NBR -15 +80 EGO 5521386 --> 306-307
326 Butterfly Valve overboard, lug DN125-DN150 LK 710702 PN16 Ductile iron Lever or actuator operated. DNV cert. AISI316 AlBr NBR -15 +80 LK Overboard valve
326 NR Valve, wafer DN40-DN250 LK 300702 PN16 Ductile iron Duo check Monel AlBr NBR -10 +80 LK
326 NR Valve closable, flanged DN40-DN250 LK 467052 NR PN16 / PN10 Cast iron Brass LG2 LG2 +120 LK 5540023 --> 426-427
326 NR Valve closable, threaded 1/4"-1 1/2" LK 456022 NR PN16 LG2 Brass LG2 +120 LK 5546681 --> 419
326 Globe Valve, threaded 1/4"-1 1/2" LK 456022 PN16 LG2 Bronze Bronze +120 LK 5573981 --> 349
326 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
326 Pressure relief valve, threaded 3/8"-2" Götze 618 T 12 bar Gunmetal Angled. Set-pressure: x bar (specify at order) PTFE +225 GÖTZE 5621756 --> 446
326 Coupling 5" FIG 50 Male PN25 Ductile iron Barite X over Fig50 Fem x Fig50 Fem
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
326 Grooved coupling, flexible DN50-DN200 Style 75 31-34bar Cast Iron Victaulic Nitril gasket (orange stripe) Below Mdeck
326 Grooved coupling, flexible DN50-DN200 Style 75 31-34bar HDGalv Victaulic Nitril gasket (orange stripe) Open deck
326 Flange DN 150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
326 Flange DN 200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
326 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
326 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
326 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
326 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
Clamps
326 Clamp - Steel pipes HD Galv. NS5550 U-bolt
326 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty
Gaskets
326 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1.5-2.0 NS 157 James Walker Compressed non asbestos fibre
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Fill / Discharge stations to be equipped with 4" Dry DisConnect coupling. Male end. Color code Brown.
Fuel oil, Lub oil and other oil bunkering stations and vent. pipes where spillage may occur shall be fitted with spill/drip trays according to DnV Pt.6 Ch.12 Sec.2 C400
Drip trays to be arranged for collection of any leakage of "oil" wich may occur from pumps, fittings etc.
All joints within tanks shall be welded, with expansion or contraction provide for by bends
All valves on deck - AISI316 handle and plate
Quick closing valves on fuel oil tanks to be of ductile iron, mounted directly on BHD.
FO pumps are to be arranged for emergency stop from Bridge and deck
Remote operated valves to be controlled from Bridge and ECR
Threaded couplings are not to be used in system for flammable liquids
Documentation of system according to Class requirements
Victaulic couplings are not allowed in machinery spaces of category A.
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
SMPEP (shipboard marine pollution emergency plan) Marpo Annex I (Reg. 37) and Annex II ( Reg. 17).
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
351 Butterfly Valve, lug DN40-DN150 EGO PN16 Ductile iron Type A = Bare shaft, Actuator operated AISI316 AlBr NBR -15 80 EGO 5521362 --> 306-307
351 Butterfly Valve, lug DN200-DN600 EGO PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI316 AlBr NBR -15 80 EGO 5521369 --> 306-307
351 Butterfly Valve, lug DN40-DN150 EGO PN16 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 80 EGO 5521377 --> 306-307
351 Butterfly Valve, lug DN200 EGO PN10 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 80 EGO 5521385 306-307
351 Butterfly Valve, lug DN200-DN600 EGO PN10 Ductile iron Type C = Gear operated AISI316 AlBr NBR -15 80 EGO 5521386 --> 306-307
351 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353--> 256-257
351 NR Valve, threaded 1/4" - 2" LK 471594 PN40 316 C16 316 C16 PTFE LK 5547501 --> 411
351 Globe valve, threaded 1/4" - 2" LK 456794 PN40 CF8M AISI316 CF8M Metal seated -20 200 LK 5547327 --> 375
351 NR Valve, wafer DN50-DN300 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 100 Genebre 5551597 --> 408
351 NR Valve closable, threaded 1/4" - 2" LK 456094 NR PN40 AISI316 AISI316 AISI316 PTFE -20 200 LK 5547318 --> 425
351 NR Valve closable, flanged DN40-DN300 LK 467002 NR PN16 Ductile iron Straight type LG2 LG2 120 LK 5540423 --> 432-433
351 NR Valve closable, flanged DN40-DN300 LK 467102 NR PN16 Ductile iron Angle type LG2 LG2 120 LK 5540523 --> 434-435
351 Mud box/loading filter, flanged on request PN10/PN40 Black/galv steel Straight type … 480
351 Y-strainer, flanged DN25-DN300 Fig. 821 PN16/PN10 Cast iron -10 300 4015733 --> 472-473
351 Y-strainer, threaded 1/4" - 1 1/2" LK 482394 PN40 SS 2343 LK 4016911 --> 471
351 Quick closing valve, flanged DN15-DN250 LK 901002 PN16/PN10 Ductile iron Straight type AISI304 AISI304 LK 5576534 --> 379
351 Quick closing valve, flanged DN15-DN250 LK 901102 PN16/PN10 Ductile iron Angle type AISI304 AISI304 LK 5576535 --> 380
351 Dry DisConnect, threaded 4" MannTek/Mento PN25 AISI316 MannTek/Mento
351 Self closing valve, threaded 1/2" - 1 1/4" LK 357692 PN16 SS 2346 SS2346 Nitrile LK 5547283 --> 466
351 Blind Flange valve, flanged DN50-DN200 EGO PN16/PN40 Steel A216-WCB AISI304 PTFE EGO 5525621 --> 483
351 Deaerator 1/2" Armstrong 11-AV 30 bar St. steel 304L St.st. 304 St.steel 440 +260 AM Instrumentering Air evacuation of flowmeter
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
351 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar Steel Victaulic Nitril gasket (orange stripe) In pump room
351 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe) Open deck
351 Flange DN40-DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
351 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
351 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
351 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
351 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) <DN150, 3 step >DN125, 2 step down 1214621 --> 30
351 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
351 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
351 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
Gaskets
351 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
Pipe system to be hot dip galvanized after prefabrication / prior to installation
All valves on deck - AISI316 handle and plate
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness.Acc.to Dnv Pt.4 Ch.6 Sec.7A201 Table A2
Fill / Discharge stations to be equipped with 4" FIG.206 couplings (WECO or similar). Female end. Color code Blue. Sampling point 2" Ball valve
FW Transfer pipe should not penetrate F.O. Tanks
All joints within Ballast tanks shall be welded, with expansion or contraction provide for by bends
Tank suction point to be located at the lowest point in the tank, and the suction end to be equipped with Cone or Elephant feet
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
352 Butterfly Valve, lug DN40-DN200 EGO PN16/PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI431 AlBr NBR -15 +80 EGO 5521362 --> 306-307
352 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
352 NR Valve, threaded 3/8"-2" LK 470022 PN16 LG2 LG2 LK 5546842 --> 417
352 NR Valve, wafer DN50-DN300 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 100 Genebre 5551597 --> 408
352 NR Valve closable, flanged DN40-DN300 LK 467052 NR PN16 Cast iron Straight type LG2 LG2 +120 LK 5540023 --> 426-427
352 NR Valve closable, flanged DN40-DN300 LK 467152 NR PN16 Cast iron Angle type LG2 LG2 +120 LK 5540123 --> 430-431
352 NR Valve closable, threaded 1/4" - 2" LK 456022 NR PN16 LG2 SM2065 LG2 LK 5546681 --> 419
352 Mud box/loading filter, flanged on request PN10-PN40 Black/Galv. steel On request 480
352 Y-strainer, flanged DN25-DN300 Fig. 821 PN16/PN10 Cast iron -10 300 4015733 --> 472-473
352 Blind Flange valve, flanged DN50-DN200 EGO PN16/PN40 Steel A216-WCB AISI304 PTFE EGO 5525621 --> 483
352 Coupling 4" Fig 206 PN25 Weco or similar
352 Deaerator 1/2" Armstrong 11-AV 30 bar St. steel 304L St.st. 304 St.steel 440 +260 AM Instrumentering Air evacuation of flowmeter
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
352 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic EPDM gasket (green stripe) All over, where connections are allowed
352 Flange DN50-DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254669 --> 43
352 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
352 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
352 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
352 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) <DN150, 3 step >DN125, 2 step down 1214621 --> 30
352 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
352 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
352 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
Clamps
352 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
352 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
Gaskets
352 Gasket INCA BS 7531 DN10 --> 80 Bar Aramid&Nitril 1,5-2,0 NS 157 200 deg James Walker Compressed non asbestos fibre
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Quick Release of the transfer hoses. Self closing Brake away coupling
Fill / Disch. Stations to be equipped with 4" DDC(Dry DisConnect) male coupling and Brake away couplings. Breakaway is available with flange and male NPT. DDC can be screwed directly into the breakaway without spacenippel. Complete coupling is then only 46cm.
All pumps to be fitted with pressure gauges on (pipe) outlet side
Minimum horizontal distance between the tank side or pipes leading to tank and shell, 760mm
Internal distance between the ends of filling lines and vent lines in the tanks to be as long as possible
The CD between the Special products pumps and the hydraulic motor to be purged with air before and after running
N2 pipe dimensions are suppliers recommendations
Pressure transmitting as well as local reading at Cargo Stations
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual (Oil Recovery Operation) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
LFL - Low Flashpoint Liquid Manual - DnV Pt.5, Ch. 7, Sec. 10 and IBC code (Inerting, fire readiness)
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
SMPEP (Shipboard Marine Pollution Emergency Plan) Marpo Annex I (Reg. 37) and Annex II (Reg. 17).
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
353 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353--> 256-257
353 Butterfly Valve, lug DN40-DN200 EGO PN16/PN10 Ductile iron Lever/gear operated AISI431 AISI351 NBR -15 +80 EGO 5521315 --> 304-305
353 Butterfly Valve, lug DN50-DN200 EGO PN25 Ductile iron Type B/C = Lever/gear operated AISI431 AlBr NBR -15 +80 EGO 5525611 --> 310-311
353 Butterfly Valve, lug DN50-DN200 EGO PN25 Ductile iron Type A = Bare shaft AISI431 AlBr NBR -15 +80 EGO 5525601 --> 310-311
353 NR valve, wafer DN40-DN200 CVD 6464M PN40 AISI 316 SS 1.4435 Metal-seated +120 CVD 5538461 --> 404-405
353 High velocity valve DN50 VQHV-ISO PN16 AISI 316 AISI 316 AISI 316 Nitril Pressure / Vac. Cargo tanks 488
353 DDC male coupling, flanged 4" Dry DisConnect PN25 AISI 316 Mento Mento
353 Brake away coupling 4" Flg/threaded PN25 AISI 316 Type Industri MannTek/Mento
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
353 Flange DN50 Weld neck PN10 AISI316 EN 1092-1 AISI316L 175
353 Flange DN50 Weld neck PN25/40 AISI316 EN 1092-1 AISI316L 176
353 Elbow DN20 PN10 AISI316 DIN 2609 AISI316L 90gr R=1,5xD 1910946 --> 150
353 Tee DN20 PN10 AISI316 EN 1.4404 AISI316L 1935933 --> 153
353 Con reducer DN25 PN10 AISI316 EN 1.4404 AISI316L 1825511 --> 154
Clamps
353 Clamp AISI316 U-bolt 3535325 --> 220
353 Clamp AISI316 Flat-bar heavy duty. Rubber inlay 1936552 --> 214
353 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty. Rubber inlay 3511806 --> 213
Gaskets
353 Gasket INCA BS 7531 DN10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Fill / Disch. Stations to be equipped with 4" DDC(Dry DisConnect) male coupling and Brake away couplings. Breakaway is available with flange and male NPT. DDC can be screwed directly into the breakaway without spacenippel. Complete coupling is then only 46cm.
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
LFL - Low Flashpoint Liquid Manual - DnV Pt.5,Ch. 7, Sec. 10 and IBC code ( Inerting, fire readiness )
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
SMPEP (shipboard marine pollution emergency plan) Marpo Annex I (Reg. 37) and Annex II ( Reg. 17).
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
354 Butterfly Valve, lug DN50-DN200 EGO PN25 Ductile iron Type A = Bare shaft, Actuator operated AISI431 AlBr NBR -15 +80 EGO 5525601 --> 310-311
354 Butterfly Valve, lug DN50-DN200 EGO PN25 Ductile iron Type B/C = Lever/gear operated AISI431 AlBr NBR -15 +80 EGO 5525611 --> 310-311
354 NR valve, wafer DN50-DN200 CVD 6464M PN40 AISI 316 SS 1.4435 Metal-seated +120 CVD 5538463 --> 404-405
354 Blind Flange valve, flanged DN50-DN200 EGO PN16/PN40 Steel A216-WCB AISI304 PTFE EGO 5525621 --> 483
354 High velocity valve DN50 VQHV-ISO PN16 AISI 316 AISI 316 AISI 316 Nitril Pressure/Vac. Cargo tanks 488
354 DDC male coupling, flanged 4" Dry DisConnect PN25 AISI 316 Mento Mento
354 Brake away coupling 4" Flg./threaded PN25 AISI 316 Type Industri MannTek/Mento
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
354 Flange DN50 PN10 AISI316 Din 2576 ISO
354 Elbow DN20 PN10 AISI316 SS2343 ISO 90gr R=1,5xD
354 Tee DN20 PN10 AISI316 SS2353 ISO
354 Con reducer DN20 PN10 AISI316 SS2343 ISO
354 Flange DN50 PN10 AISI316 DIN 2633 AISI316
Clamps
354 Clamp AISI316 U-bolt
354 Clamp AISI316 Flat-bar heavy duty. Rubber inlay 3511806 --> 217
Gaskets
354 Gasket INCA BS 7531 DN10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Quick Release of the transfer hoses: Self closing break away coupling
Fill / Disch. Stations to be equipped with 4" DDC(Dry DisConnect) male coupling and Brake away couplings. Breakaway is available with flange and male NPT. DDC can be screwed directly into the breakaway without spacenippel. Complete coupling is then only 46cm.
Emergency Stop to be arranged on deck for cargo pumps
All pumps to be fitted with pressure gauges on (pipe) outlet side
Minimum horizontal distance between the tank side or pipes leading to the tank and shell 760mm
Internal distance between the ends of filling lines and vent lines in the tanks to be as long as possible
The CD between the Special products pumps and the hydraulic motor to be purged with air before and after running
N2 pipe dimensions are suppliers recommendations
Pressure transmitting as well as local reading at Cargo Stations
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
LFL - Low Flashpoint Liquid Manual - DnV Pt.5,Ch. 7, Sec. 10 and IBC code ( Inerting, fire readiness )
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
SMPEP (shipboard marine pollution emergency plan) Marpo Annex I (Reg. 37) and Annex II ( Reg. 17).
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
355 Butterfly valve, lug DN50 EGO PN16 Ductile iron Lever/gear operated AISI 431 A351-CF8M NBR -15 +80 EGO 5521315 --> 304-305
355 NR valve, wafer DN50-DN200 CVD 6464M PN40 AISI 316 SS 1.4435 Metal-seated +120 CVD 5538463 --> 404-405
355 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
355 High velocity valve DN50 VQHV-ISO AISI 316 AISI 316 AISI 316 Nitril Pressure/Vac. cargo tanks 488
355 DDC male coupling, flanged 4" Dry DisConnect PN25 AISI 316 Mento Mento Mento
355 Brake away coupling 4" Flg./threaded PN25 AISI 316 Type Industri MannTek/Mento Mento
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
355 Flange DN50 PN10/PN16 AISI316 DIN 2633 AISI316 1934584 --> 175
355 Elbow DN20 PN10 AISI316 DIN 2609 AISI316 90gr R=1,5xD 1910946 --> 150
355 Tee DN20 PN10 AISI316 EN 1.4404 AISI316 1914841 --> 153
355 Con reducer DN20 PN10 AISI316 EN 1.4404 AISI316 1825511 --> 154
Clamps
355 Clamp AISI316 U-bolt
355 Clamp AISI316 Flat-bar heavy duty. Rubber inlay 3511806 --> 213
Gaskets
355 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness. Acc. to Dnv Pt.4 Ch.6 Sec.7A201 Table A2
Valves of size DN 125 and bigger with design pressure above 16 bar to have DNV product certificate acc. to DNV 4.6.7 C301.
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
356 Ball valve, threaded 1/4"-2" Haitima 2006 64 bar A351-CF8M AISI316 AISI316 PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
356 Ball valve, flanged DN65-DN150 Haitima 2019D PN40 A351-CF8M A276-316 A351-CF8M CTFE TFM 1600 -40 +200 Haitima 5600249 --> 260-261
356 Coupling 4" Fig 206 FM PN25 Ductile FeMale Mento
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
356 Grooved coupling, flexible DN50-DN250 Style 77 34,5 bar Rilsan treated with Cont.Clip75 Victaulic Nitril gasket (orange stripe)
356 Flange DN150 PN16 NS2527 Suction side 1254629 --> 43
356 Flange DN200 PN10 NS2526 Suction side 1254429 --> 42
356 Flange DN150 PN40 NS2529 Pressure side 1254864 44
356 Flange DN150 PN25 NS1764 Pressure side 1253029 37
356 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
356 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
356 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
356 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
356 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
356 Flange DN50 PN10 AISI316 DIN 2633 AISI316 1934584 --> 175
356 Elbow DN20 PN10 AISI316 SS2343 ISO 90gr R=1,5xD 1910928--> 150
356 Tee DN20 PN10 AISI316 SS2353 ISO 1914841--> 153
356 Con reducer DN20 PN10 AISI316 SS2343 ISO 1825511--> 154
Clamps
356 Clamp AISI316 Flat-bar heavy duty. Rubber inlay 1936552 --> 214
356 Clamp AISI316 U-bolt 3535325 --> 220
Gaskets
356 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
356 Pipe Dn25 ø33,7 PN25 Steel 4,0 DN25 Bending N/A EN 10216-2 P235GH (St 35.8) 1111844 4
356 Pipe DN40 ø48,3 PN25 Steel 4,5 6,3 DN40 Bending N/A EN 10216-2 P235GH (St 35.8) 1112721/1112787 4
356 Pipe Dn50 ø60,3 PN25 Steel 4,5 6,3 4,5 6,3 EN 10216-2 P235GH (St 35.8) 1113227/1113293 4
356 Pipe DN65 ø76,1 PN25 Steel 4,5 6,3 6,3 6,3 EN 10216-2 P235GH (St 35.8) 1113953/1114019 4
356 Pipe DN80 ø88,9 PN25 Steel 4,5 8,0 6,3 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1114393/1114503 4
356 Pipe DN100 ø114,3 PN25 Steel 4,5 8,0 6,3 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115009/1115119 5
356 Pipe DN125 ø139,7 PN25 Steel 4,5 8,0 6,3 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115603/1115713 5
356 Pipe DN150 ø168,3 PN25 Steel 4,5 8,8 6,3 8,8 EN 10216-2 P235GH (St 35.8) 1101066/1116263 5
356 Pipe DN200 ø219,1 PN25 Steel 6,3 8,8 8,8 8,8 EN 10216-2 P235GH (St 35.8) 1101099/1116659 5
356 Pipe DN250 ø273,0 PN25 Steel 6,3 8,8 DN250 Bending N/A EN 10216-2 P235GH (St 35.8) 1101122/1116923 5
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Pipe system to be hot dip galvanized after prefabrication / prior to installation
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Valves of size DN 125 and bigger with design pressure above 16 bar to have DNV product certificate acc. to DNV 4.6.7 C301.
Mud circulation below main deck (to top section of tanks)
Fill / Discharge stations to be equipped with 5" FIG.50 couplings(WECO or similar). Female end. Color code Black. Equipped with 2" Ball valve air blow down. It is recommended for DDC Stainless on Liquid MUD
Horizontal pump suction line. The suction end to be equipped with Cone or Elephant feet
Threaded couplings are not to be used in system for flammable liquids
Vent.pipe dimension on tanks to be 2 x OD dimension of filling pipe
Valves to be acc. to Dnv Pt.4 Ch.6 Sec.2 A400-A500
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
SMPEP (shipboard marine pollution emergency plan) Marpo Annex I (Reg. 37) and Annex II ( Reg. 17).
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
357 Butterfly valve, lug DN40-DN600 EGO PN25 Ductile iron Type A = Bare shaft, Actuator operated AISI316 AlBr NBR -15 +80 EGO 5525601 --> 310-311
357 Butterfly valve, lug DN40-DN200 EGO PN25 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 +80 EGO 5525611 --> 310-311
357 Butterfly valve, lug DN200 EGO PN25 Ductile iron Type C = Gear operated AISI316 AlBr NBR -15 +80 EGO 5525617 310-311
357 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
357 NR Valve , wafer DN50 - DN250 Fig. 2402 PN25 A351-CF8M Duo check A351-CF8M Viton (FKM) -10 +180 Genebre 5551608 --> 409
357 Mud box, flanged On request PN10/PN40 Black/Galv. steel 480
357 Blind Flange valve, flanged DN50-DN200 EGO PN16/PN40 Steel A216-WCB AISI304 PTFE EGO 5525621 --> 483
357 Air vent valve, flanged DN125-DN250 MUD 1 PN10/16 Galv. Steel Can be delivered with flame screen PE Neoprene John Gjerde 487
357 Coupling 5" Fig 50 FM PN25 Ductile iron Weco or similar
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
357 Grooved coupling, flexible DN50-DN250 Style 77 34,5 Bar HD Galv. Victaulic Nitril gasket (orange stripe) In pump room and open deck
357 Grooved coupling, rigid DN50-DN250 Style 07 34,5-41,4 bar HD Galv. Victaulic Nitril gasket (orange stripe) In pump room and open deck
357 Flange DN40 PN40 Steel NS2529 S235 JR (RSt. 37.2) 1254864--> 44
357 Flange DN40 PN25 Steel NS2529 S235 JR (RSt. 37.2) 1254864--> 44
357 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411--> 29
357 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766--> 22
357 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) <DN150, 3 step >DN125, 2 step down 1214621--> 30
357 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822--> 26-27
357 End Cap Steel EN 10028-2 P265GH 1208404--> 33
357 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133--> 31
Clamps
357 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806--> 213
357 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153--> 221
Gaskets
357 Gasket INCA BS 7531 DN10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
358 Grooved coupling, flexible DN50-DN250 Style 77 34,5 Bar HD Galv. Victaulic Nitril gasket (orange stripe) All over
358 Grooved coupling, rigid DN50-DN250 Style 07 34,5-41,4 bar HD Galv. Victaulic Nitril gasket (orange stripe) All over
358 Flange DN40 PN40 Steel NS2529 S235 JR (RSt. 37.2)
358 Flange DN40 PN25 Steel NS2529 S235 JR (RSt. 37.2)
358 T-pipe Steel EN 10253-2 P235GH (St.35.8)
358 Elbow Steel EN 10253-2 P235GH (St.35.8)
358 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8)
358 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8)
358 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
358 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only
Clamps
358 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty
358 Clamp - Steel pipes HD Galv. NS5550 U-bolt
Gaskets
358 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
Gaskets
359 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness. Acc. To Dnv Pt.4 Ch.6 Sec. 7A201 Table A2
Steel pipes to be hot dip galvanized after prefabrication / prior to installation
Cromium fittings to be used on all precision steel pipes - EN 10305 / DIN 2391
Discharge station 2" Camlock hose connection
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11, and NOFO Standard
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
382 Butterfly valve, lug DN40-DN600 EGO PN16/PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI431 AlBr NBR -15 +80 EGO 5521362 --> 306-304
382 Butterfly valve, lug DN40-DN200 EGO PN16/PN10 Ductile iron Type B = Lever operated AISI431 AlBr NBR -15 +80 EGO 5521377 --> 306-304
382 Butterfly valve, lug DN200-DN600 EGO PN10 Ductile iron Type C = Gear operated AISI431 AlBr NBR -15 +80 EGO 5521386 --> 306-304
382 Ball valve, threaded 1/4"-2" Haitima 2006 64 bar AISI316 AISI316 AISI316 PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
382 Ball valve, threaded 1/4"-2" Haitima 2013DM PN63 AISI316 AISI316 AISI316 PTFE -20 +200 Haitima (EGO) 5600602 --> 270-271
382 Ball valve, flanged DN15-DN200 Haitima 2019D PN16/PN40 ASTM-A216-WCB PTFE -20 +200 Haitima (EGO) 5600231 --> 260-261
382 NR valve, threaded 1/4" - 2" LK 471594 PN40 316 C16 316 C16 PTFE LK 5547501 --> 411
382 NR valve, wafer DN40 - DN250 LK 300702 PN16 Ductile iron Duo check Monel AlBr NBR -10 80 LK
382 NR valve closable, threaded 1/4" - 2" LK 456022 NR PN 16 LG2 SM2065 LG2 LK 5546681 --> 419
382 Y-strainer, flanged DN40-DN200 Fig. 821 PN10/PN16 Cast Iron -10 +300 4015735 --> 472-473
382 Camloc coupling 2" Male type A PN25 Ductile iron With dust cap
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
382 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe) Pump room/open deck
382 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254669 --> 43
382 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
382 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
382 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
382 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
382 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
382 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
382 Saddles Steel EN 10216-2 P235GH (St.35.8) 1207133 --> 31
382 Flange DN50 Weld neck PN16 AISI316 EN 1092-1 AISI316 1934575 --> 175
382 Colas pressed DN50 PN10 AISI316 EN 10204 AISI316 1927902 --> 163
382 Alu slip-on flange DN50 PN10 ALU DIN 2642 1836358 --> 164
382 Elbow DN20 PN16 AISI316 SS2343 ISO 90gr R=1,5xD 1910928 --> 150
382 Tee DN20 PN16 AISI316 SS2353 ISO 1914841 --> 153
382 Con reducer DN20 PN16 AISI316 SS2343 ISO 1825511 --> 154
1825511 -->
Clamps
382 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
382 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
Gaskets
382 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
382 Pipe DN25 ø33,7 PN16 Steel 4,0 DN25 Bending N/A EN 10216-2 P235GH (St 35.8) 1111844 4
382 Pipe DN40 ø48,3 PN16 Steel 4,5 6,3 DN40 Bending N/A EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1112721/1112787 4
382 Pipe DN50 ø60,3 PN16 Steel 4,5 6,3 4,5 6,3 EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1113227/1113293 4
382 Pipe DN65 ø76,1 PN16 Steel 4,5 6,3 4,5 6,3 EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1113953/1114019 4
382 Pipe DN80 ø88,9 PN16 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1114393/1114503 4
382 Pipe DN100 ø114,3 PN16 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1115009/1115119 5
382 Pipe DN125 ø139,7 PN16 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1115603/1115713 5
382 Pipe DN150 ø168,3 PN16 Steel 4,5 8,8 4,5 8,8 EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1101066/1116263 5
382 Pipe DN200 ø219,1 PN16 Steel 6,3 8,8 6,3 8,8 EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1101099/1116659 5
382 Pipe DN250 ø273,0 PN16 Steel 6,3 8,8 DN250 Bending N/A EN 10216-2 P235GH (St 35.8) Thickness tank: Table A2 Pt.4 Ch.6 Sec.7 1101122/1116923 5
382 Pipe DN50 ø 60,3 PN16 AISI316L 2.0 N/A EN 10217-7 AISI316L 1902704 140
382 Pipe DN65 ø 76,1 PN16 AISI316L 2.0 N/A EN 10217-7 AISI316L 1902737 140
382 Pipe DN80 ø 88,9 PN16 AISI316L 2.0 N/A EN 10217-7 AISI316L 1902782 140
382 Pipe DN100 ø 114,3 PN16 AISI316L 2,6 N/A EN 10217-7 AISI316L 1902839 140
382 Pipe DN125 ø 139,7 PN16 AISI316L 2,6 N/A EN 10217-7 AISI316L 1902873 140
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
System to be made acc. to stability requirements / calculations.
Wall thickness of pipes in tanks containing same substance as in actual pipe do NOT need extraordinary wall thickness
Actuator on butterfly valve next to anti-heeling pump to have spring return (Fail=close). Actuator on butterfly valve on crossover vent pipe between heeling tanks to be without spring return.
Pipe system to be hot dip galvanized after prefabrication / prior to installation
The pumps to be arranged with pressure/vacuum gauge on suction and discharge
Pump start to be interlocked with rmote operated vent/overflow valve in open position
End of suction pipes to be located at lowest point in tanks
All joints within tanks shall be welded, with expansion or contraction provided for by bends
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
405 Butterfly valve, lug DN200-500 EGO PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI431 AlBr NBR -15 +80 EGO 5521371 --> 306-307
405 Butterfly valve, lug DN200-500 EGO PN10 Ductile iron Type C = Gear operated AISI431 AlBr NBR -15 +80 EGO 5521387 --> 306-307
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
405 Grooved coupling, flexible DN350-DN500 W77 AGS 20 bar Ductile iron Victaulic EPDM gasket (green stripe)
405 Flange DN200 --> PN10 Steel NS2526 S235JR 44
405 Reducer Steel EN 10253-2 P235GH TC1
405 Gasket INCA BS 7531 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
The AC/OX equipment package (bottles, high pressure pipes, misc. valves) is delivered by subsupplier. Yard delivery is only low pressure distribution pipes.
Test pressure stated in this pipe standard is only valid for the distribution pipes installed by the yard.
No fitting connections are allowed, only welded connections. Connections to be clearly visible for inspection. (ref. NMD reg. 422 §16).
No pipes through accommodation area for crew or passengers. (ref. NMD reg. 422 §16).
Outlet connections only in machinery spaces and in workshop, ref. NMD reg. 422 §16 (outlet connections on open deck may be accepted, ref. NMD reg. 422 §21).
Vent pipe from safety valves to be routed up to 3 meters above deck. (ref. NMD reg. 422 §16).
Maximum number of outlets is normally 2 per pipe system. (ref. NMD reg. 422 §16), but exceptions may be accepted (ref. NMD reg. 422 §21).
Installation certificate to be issued from qualified personnel (ref. NMD reg. 422 §19).
Gaskets
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
AISI304 pipes shall be used in areas that required crossing fire zone
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.E references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
444 Wall outlet Brass Beam / Foma
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.E references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
444 Elbow PVC Beam/Foma
444 T-pipe PVC Beam/Foma
444 T-pipe AISI304 AISI304 Blücher
444 Elbow AISI304 AISI304 Blücher
444 Penetration AISI304 AISI304 Blücher
444 Clamp Steel Sikla Proclamp Blücher/Europipe/PVC pipes 2171183 --> 230 BD VVS tech. catalog 2012
Gaskets
444 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
EPDM gaskets and seals to be used
Cromium fittings to be used on all precision steel pipes - EN 10305 / DIN 2391
All valves on deck - AISI316 handle and plate
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Remote operated valves to be controlled from ECR
All pumps to be fitted with pressure gauges on inlet/outlet side
Vent. to exp.tanks to be located from high loops in the systems where air can accumulate
The end of the probe to be installed as close as possible to the center of flow path. To be mounted 1m away from the valves and min. 1m away from any junction on the pipe
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
Pipes and valves to be insulated with ARMAFLEX/Kaiflex 19mm or similar approved type, re-inforced with tape.
Pipes to be insulated against clamps, bulkhead, deck and web penetrations to avoid condensing.
Roxtec rubber sealing plugs only for water and gas tight penetrations through deck and bulkhead. For other penetrations, use free holes.
Loops to be avoided if possible. If a loop is inevitably, deaerator valve to be mounted.
Clean Design Class Manual - DnV Pt.6 Ch.12, Sec.3 , Marpol Annex I, II, IV, V and VI including Nox
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
571-101 Butterfly valve, lug DN50 EGO PN 10 Ductile iron Lever / gear operated AISI 431 A351-CF8M EPDM -20 +120 EGO 5521301 --> 304-305
571-101 NR valve, wafer DN50-DN250 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 +100 Genebre 5551597 --> 408
571-101 NR valve closable, flanged DN40-DN250 LK 467052 NR PN16/PN10 Cast iron Straight type SM 2065 LG2 LG2 +120 LK 5540023 --> 426-427
571-101 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
571-101 Flow reg. valve, threaded 3/8" - 2" STAD 16 bar AMETAL Straight type AMETAL LG2 EPDM -20 +120 TA Hydronics 8522303 --> 298
571-101 Flow reg. valve, threaded 3/8" - 2" Hydrocontrol VTR 16 bar Bronze Straight type Brass Brass PTFE -20 +150 Oventrop
571-101 Flow reg. valve, flanged DN50 - DN250 STAF PN16 GG25 Straight type AMETAL LG2 EPDM -20 +120 TA Hydronics 8521951 --> 299
571-101 Flow reg. valve, flanged DN50 - DN250 Hydrocontrol VFC PN16 Cast iron Straight type Bronze Bronze PTFE -10 +150 Oventrop
571-101 Pressure relief valve, threaded 3/8"-2" Götze 618 T 12 bar Gunmetal Angled. Set-pressure: x bar (specify at order) PTFE +225 GÖTZE 5621756 --> 446
571-101 Temp.reg.valve DN15 VG7xxxx/ VG8xxx PN16 Cast Bronze Johnsen Controls / AMOT … …
571-101 Flex. hose coupling PN16 EPDM Rubber w/AISI316 flange EPDM
571-101 Flex.rubber bellow, flanged T-50 PN16 EPDM Rubber w/steel flange EPDM 8541303 --> 454
571-101 Deaerator 1/2" Flamco Flexvent Super 10 bar Bronze -10 +120 Flamco Air vent for high points in the system
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
571-101 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar Steel Victaulic EPDM gasket (green stripe)
571-101 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
571-101 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
571-101 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
571-101 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
571-101 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
571-101 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
571-101 Sealing penetration DN40 ROXTEC
Clamps
571-101 Clamp HD Galv. Clamps for refrigeration/Freeze w/insulation Steel pipes HS 7326.90 225 HS code int.
571-101 Clamp HD Galv. U-bolt Steel pipes 3477153 --> 221
571-101 Clamp DIN3015 Part 1 Polypropylen (PP) Prec.steel pipes
Ermeto fittings
571-101 Union ø6 - ø30 PN100 - 400 AISI316 1780104 --> 144
571-101 Elbow ø6 - ø30 PN100 - 400 AISI316 1780354 --> 144
571-101 Tee ø6 - ø30 PN100 - 400 AISI316 1780604 --> 145
Gaskets
571-101 Gasket INCA BS 7531 DN10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
571-101 Pipe DN50 ø60,3 PN10/ PN16 AISI316L 2,0 N/A EN 10217-7 AISI316L Convert
571-101 Pipe DN65 ø76,1 PN10/ PN16 AISI316L 2,0 N/A EN 10217-7 AISI316L Convert
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
Cromium fittings to be used on all precision steel pipes - EN 10305 / DIN 2391
All valves on deck - AISI316 handle and plate
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
All clamps, bulkhead, deck and web penetrations to be fully isolted from pipe to avoid condensation
Loops to be avoided if possible. If a loop is inevitably, deaerator valve to be mounted
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - PIPES INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION DIAMETER OUTSIDE DIAMETER PRESSURE MATERIAL Standard wall thickness [mm] Wall thickness for pipe bending STANDARD REMARKS NRF NO. PAGE NOTE
NOMINAL [mm] RATING R=1,5xD [mm] NUMBER
General Tank Overboard General Tank Norm Grade
571-102 Pipe DN80 ø88,9 PN10 Steel 4,5 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1114393 4
571-102 Pipe DN100 ø114,3 PN10 Steel 4,5 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115009 5
571-102 Pipe DN125 ø139,7 PN10 Steel 4,5 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115603 5
571-102 Pipe DN150 ø168,3 PN10 Steel 4,5 4,5 8,8 EN 10216-2 P235GH (St 35.8) 1101066 5
571-102 Pipe DN200 ø219,1 PN10 Steel 6,3 6,3 8,8 EN 10216-2 P235GH (St 35.8) 1101099 5
571-102 Pipe DN250 ø273,0 PN10 Steel 6,3 DN250 Bending N/A EN 10216-2 P235GH (St 35.8) 1101122 5
571-102 Pipe DN300
571-102 Pipe DN350
571-102 Pipe DN400
571-102 Pipe DN450
571-102 Pipe DN500
571-102 Pipe DN600
571-102 Pipe DN800
571-102 Spiro pipe PR80 ø080,5/112,5 Steelsheet 0,5 VENTISTÅL INSULATED 16MM MINERAL WOOL
571-102 Spiro pipe PR100 ø100,5/158,6 Steelsheet 0,5 VENTISTÅL INSULATED 16MM MINERAL WOOL
571-102 Spiro pipe PR125 ø125,5/158,6 Steelsheet 0,5 VENTISTÅL INSULATED 16MM MINERAL WOOL
571-102 Spiro pipe PR160 ø160,6/194,7 Steelsheet 0,6 VENTISTÅL INSULATED 16MM MINERAL WOOL
571-102 Spiro pipe PR200 ø200,7/232,8 Steelsheet 0,6 VENTISTÅL INSULATED 16MM MINERAL WOOL
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
EPDM gaskets and seals to be used
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Remote operated valves to be controlled from ECR
Copper pipes to be used for all hot and cold freshwater systems in accomodation
Inlet/Outlet of coolers to be fitted with thermometers. Thermometer and sensors to be placed in AISI316 pockets
All pumps to be fitted with pressure gauges on inlet/outlet side
Deaerators to be placed on all high loops/points in system to ensure sufficient deaeration of system
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
P&A Procedures and Arrangements Manual - MARPOL 73/78, Annex II - IBC-codes (international code for construction and equipment of ships carrying dangerous chemicals in bulk) , P&A for supply vessels IMO Res. A 673 ( 16 )
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
577 Butterfly valve, lug DN40-DN600 EGO PN16/PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI431 CF8M EPDM -20 +120 EGO 5521301 --> 304-305
577 Butterfly valve, lug DN40-DN200 EGO PN16/PN10 Ductile iron Type B = Lever operated AISI431 CF8M EPDM -20 +120 EGO 5521301 --> 304-305
577 Y-strainer, threaded 3/8"-2" CIM 74-A 20 bar Bronze St.St. strainer -10 +100 Cim 4015502 --> 470
577 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353--> 256-257
577 NR valve, wafer DN50-DN300 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 +100 Genebre 5551597 --> 408
577 NR valve , threaded 3/8"-2" LK 470022 PN16 LG2 LG2 LK 5546842 --> 419
577 NR valve closable, flanged DN40-DN300 LK 467052 NR PN16 Cast iron Straight type LG2 LG2 +120 LK 5540023 --> 426-427
577 NR valve closable, threaded 1/4"-1 1/2" LK 456022 NR PN16 LG2 Straight type LG2 +120 5546681 --> 419
577 Flow reg. valve, straight, threaded 3/8" - 2" STAD PN16 AMETAL AMETAL LG2 EPDM -20 +120 TA Hydronics 8522303 --> 298
577 Flow reg. valve, straight, flanged DN65 - DN150 STAF PN16 GG25 AMETAL LG2 EPDM -20 +120 TA Hydronics 8521951 --> 299
577 Pressure relief valve, threaded 3/8"-2" Götze 618 T 12 bar Gunmetal Angled. Set-pressure: x bar (specify at order) PTFE +225 GÖTZE 5621756--> 446
577 Deaerator 1/2" Flamco Flexvent Super 10 bar Bronze -10 +120 Flamco Air vent for high points in the system
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
577 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar Steel Victaulic EPDM gasket (green stripe)
577 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254669 --> 43
577 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
577 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
577 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
577 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
577 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
577 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
577 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
577 Isolation ø76,1 Rockwool 40mm Rockwool Pipe section with alu cover & tape
577 Isolation ø60,3 Rockwool 30mm Rockwool Pipe section with alu cover & tape
Clamps
577 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
577 Clamp -Tico clip S / CL DN50 Steel Tico Max working temp 100 deg.C Installed between support and pipe
Gaskets
577 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
577 Copper tube 1/2" ø12 PN16 Copper 1,0 N/A EN 1057 (NS1758) According to DNV 1,2mm thickness
577 Copper tube 1/2" ø15 PN16 Copper 1,0 N/A EN 1057 (NS1758) According to DNV 1,2mm thickness
577 Copper tube 3/4" ø22 PN16 Copper 1,0 N/A EN 1057 (NS1758) According to DNV 1,5mm thickness
577 Copper tube 1" ø28 PN16 Copper 1,2 N/A EN 1057 (NS1758) According to DNV 1,5mm thickness
577 Copper tube 1 1/4" ø35 PN16 Copper 1,5 N/A EN 1057 (NS1758) According to DNV 1,5mm thickness
577 Copper tube 1 1/2" ø42 PN16 Copper 1,5 N/A EN 1057 (NS1758) According to DNV 1,5mm thickness
577 Copper tube 2" ø54 PN16 Copper 1,5 N/A EN 1057 (NS1758) According to DNV 2,0mm thickness
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
Cromium fittings to be used on all precision steel pipes - EN 10305 / DIN 2391
All valves on deck - AISI316 handle and plate
All tap connections to WC and Sink to be copper ø10mm
Tap connections, where otherwise not specified, to be copper ø12mm
Ball valves (Ballofix) to be provided on all tap connections
Hot water pipes to be insulated. Cold water pipes to be insulated outside engine room areas, except pipes from Solenoid valve to Bride windows (Window flushing)
As far as possible pipes to be placed in hight above bathroom modules
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
581 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
581 Butterfly , lug DN40-DN150 EGO PN16 Ductile iron AISI431 AlBr NBR -15 +80 EGO 5521362 --> 306-307
581 Butterfly , lug DN200 EGO PN10 Ductile iron AISI431 AlBr NBR -15 +80 EGO 5521369 --> 306-307
581 NR valve, wafer DN50-DN300 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 100 Genebre 5551597 --> 408
581 NR valve, threaded 3/8" - 2" Altech CIM 30 CIM 30 5546206 --> 341 BD VVS tech. catalog 2012
581 NR valve closable, threaded 1/4" - 1 1/2" LK 456022 NR PN16 LG2 Straight type Brass LG2 +100 LK 5546681 --> 419
581 Y-strainer, threaded 3/8"-2" CIM 74-A 20 bar Bronze St.St. strainer -10 +100 Cim 4015502 --> 470
581 Y-strainer, flanged DN25-DN250 Fig. 821 PN16/PN10 Cast iron -10 +300 4015753 --> 472-473
581 Pressure relief valve, threaded 3/8"-2" Götze 618 T 12 bar Gunmetal Angled. Set-pressure: x bar (specify at order) PTFE +225 GÖTZE 5621756 --> 446
581 Frost proof valve FMM 4290-8520 PN16 FMM 4303805
581 Frost proof valve FMM 4282-0050 PN16 FMM 4303818
581 Vacuum breaker DURGO PN16 DURGO
581 Solenoid valve PN16 Delivered by pump supplier
581 Solenoid valve 3/8" - 1" Danfoss EV250BD PN16 Brass Normally closed (NC) DANFOSS 5640221 --> 335 BD VVS tech. catalog 2012
581 Flow reg. valve, threaded 3/8" - 2" STAD PN16 AMETAL Straight type AMETAL LG2 EPDM -20 +120 TA Hydronics 8522303 --> 298
3-way thermostatic reg. valve,
581 3/4" - 2" JRGUMAT 3400 PN16 Brass Use one dim. larger than pipe dim. JRGUMAT 4451106 --> 339 BD VVS tech. catalog 2012
manual adjustable
3-way thermostatic reg. valve,
581 1" - 1 1/4" MT 52 PN16 Brass +30 +70 TACONOVA
manual adjustable
581 Pressure reducing valve, threaded 1/4" - 2" D22, Habedo 40 bar LG2 +70 Habedo 5627103 --> 440
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
581 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
581 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
581 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
581 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
581 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
581 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
581 T-pipe Copper Viega Pressfittings
581 Elbow Copper Viega Pressfittings
581 Isolation 20,0 Rockwool 20mm Pipe section with alu cover & tape
Clamps
581 Clamp - Steel pipes HD Galv. Flat-bar heavy duty 3511806 --> 213
581 Clamp - Steel pipes HD Galv. U-bolt 3477193 --> 221
581 Clamp - Prec.st. pipes & CU pipes Steel DIN3015 Part 1 Polypropylen (PP) Not CU pipes in accomodation area
581 Clamp - Cu pipes Steel SIKLA PROCLAMP Only Cu pipes in accomodation area
Gaskets
581 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
581 Precision tube ø12 PN10 AISI 316L 2.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø15 PN10 AISI 316L 2.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø18 PN10 AISI 316L 2.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø22 PN10 AISI 316L 2.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø28 PN10 AISI 316L 2.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø35 PN10 AISI 316L 2,5 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø42 PN10 AISI 316L 3.0 N/A EN 10305-1 AISI316L Open deck
581 Precision tube ø12 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120164
581 Precision tube ø15 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120254
581 Precision tube ø18 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120377
581 Precision tube ø22 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120633
581 Precision tube ø28 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120877
581 Precision tube ø35 PN10 Steel 2,5 N/A EN 10305-4 E235 (St.37.4) 1121311
581 Precision tube ø42 PN10 Steel 3.0 N/A EN 10305-4 E235 (St.37.4) 1121708
581 Copper tube 1/2" ø12 PN16 Copper 1,0 N/A EN 1057 (NS1758)
581 Copper tube 1/2" ø15 PN16 Copper 1,2 N/A EN 1057 (NS1758)
581 Copper tube 3/4" ø22 PN16 Copper 1,5 N/A EN 1057 (NS1758)
581 Copper tube 1" ø28 PN16 Copper 1,5 N/A EN 1057 (NS1758)
581 Copper tube 1 1/4" ø35 PN16 Copper 1,5 N/A EN 1057 (NS1758)
581 Copper tube 1 1/2" ø42 PN16 Copper 1,5 N/A EN 1057 (NS1758)
581 Copper tube 2" ø54 PN16 Copper 1,5 N/A EN 1057 (NS1758)
581 Pipe DN65 ø76,1 PN16 Stainless 2,0 N/A EN 10217-7 AISI316L
581 Pipe DN80 ø88,9 PN16 Stainless 2,0 N/A EN 10217-7 AISI316L
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
All valves on deck - AISI316 handle and plate
Avoid use of 90 deg bend (1,5D) on food waste line
Gravity Drain pipes to have minimum slope of 35 mm/m
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Overboard valves size DN 125 and bigger to have DNV product certificate acc. to DNV 4.6.7 C301.
Connecting sleeves are not allowed on overboard pipes with substantial thickness (DNV 4.6.7 F103)
All valves, cocks and connections shall be readily accessible for maintenance and operation. Pipe runs shall be designed for easy removal
Hull penetrations and adjoining valves shall be in accordance with DnV Pt.3 Ch.3 Sec.6 K103
Sewage overboard connection shall be positioned such as to ensure that the contaminates from sewage discharge do not recirculate to the sea cest
Rodding points are to be installed at each T/S module and as far as possible at change of direction of 90 degrees
Expansion joints to be installed where required
Notice to be placed in Galley: " Food waste shall not be discharged via garburator less than 3 miles from land"
Discharge to shore connection flange as per MARPOL 73/78 Annex IV, Regulation 11
Installation guidelines from equipment suppliers to be strictly followed
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
Clean Design Class Manual - DnV Pt.6 Ch.12, Sec.3 , Marpol Annex I, II, IV, V and VI including Nox
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
582 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar AISI316 AISI316 AISI316 PTFE -20 +200 HAITAMA (EGO) 5605353 --> 257
582 Ball valve, 3 way, threaded 1/4" - 2" Haitima 2057 64 bar A351-CF8M Specify L- or T-port AISI316 SS A351-CF8M PTFE Haitima 5601173 --> 275
582 Ball valve, flanged DN15-DN100 LK 446152 PN16 Cast iron Brass Hard crome brass PTFE LK 5594072 --> 267
582 Butterfly valve, lug DN50-DN200 EGO PN25 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 +80 EGO Only grey water 5525611 --> 311
582 NR closable storm flap valve, flanged DN50-DN150 LK 159101 4 bar Ductile iron Angle type. DNV cert. >DN100 SM2065 RG5 NBR LK Overboard valve 5551624 --> 462
582 NR closable storm flap valve, flanged DN50-DN150 LK 159701 4 bar Ductile iron Straight type. DNV cert. >DN100 SM2065 RG5 NBR LK Overboard valve 5551824 --> 463
582 Ball Check valve DN50-DN200 LK 472451 PN10 Cast iron NBR LK Used together with Storm Flap Valve Page 83 LK catalogue
582 NR Valve, flanged DN25-DN150 LK 305852 PN16 Cast iron Full bore, swing check Steel St. 52.3 NBR LK 5547471 --> 418
582 NR Valve DN50 PN10 Ø50, Jets supply Electrolux Vacuum system
582 Vacuum breaker DURGO Br. Dahl supply
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
582 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
582 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
582 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe)
582 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
582 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
582 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
582 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
582 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
582 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
582 T-pipe AISI304 AISI304 Blücher
582 Elbow AISI304 AISI304 Blücher
582 Penetration Ø50-110mm 866.015.05 AISI304 AISI304 Blücher Main lines penetrations Cabinets, vacum and all beams, decks Sec.5 page 17
582 Penetration Ø50-110mm 868 AISI304 AISI304 Blücher Cabinets gray water Sec.5 page 17
582 Scupper Ø50mm 475.200.50 AISI304 AISI304 Blücher Scupper in general Sec.5 page 17
Clamps
582 Clamp HD Galv. Flat-bar heavy duty Steel Pipes 3511806 --> 213
582 Clamp HD Galv. U-bolt Steel Pipes 3477193 --> 221
582 Clamp Steel Sikla Proclamp Blücher pipes / Europipe 2171183 --> 230 BD VVS tech. catalog 2012
Gaskets
582 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
582 Pipe ø50 PN10 AISI304 1,0 N/A AISI304 Blücher / Europipe, 3m lenght 2170006 227 BD VVS tech. catalog 2012
582 Pipe ø75 PN10 AISI304 1,0 N/A AISI304 Blücher / Europipe, 3m lenght 2170007 227 BD VVS tech. catalog 2012
582 Pipe ø110 PN10 AISI304 1,0 N/A AISI304 Blücher / Europipe, 3m lenght 2170008 227 BD VVS tech. catalog 2012
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
Pipes on open deck to be AISI316 L
All valves on deck - AISI316 handle and plate
Pipes to be sloped down against condensate trap. Typical 1:100. Number of condensate traps to be stated during pipe routing. Ref. DNV Pt.4 Ch.6 Sec.5 G101
Uphill slope for boiler safety valves, length is to be minimum. Boiler safety valve, minimum 2 pcs pr. boiler. ref. DnV Pt.4 Ch.7 Sec.6 B100
Number of pipe expansion loopes to be stated during pipe routing
Feedwater pumps to be independently driven. Ref. DNV Pt.4 Ch.6 Sec. 5 F101
Steam distributor stack not to be painted
Valves and cocks for blow down of boiler ref. DnV Pt.4 Ch.6 Sec.3 A305 and DnV Pt.4 Ch.7 Sec.6 D100
Pipes above or behind switchboards shall as far as possible be avoided. If impracticable detachable joints and valves to be at a safe distance from switchboards. Ref. DnV Pt.4 Ch.6 Sec.3 A106
Clamps to have cork inlay to reduce heat transfer and insulation of pipes acc to DnV Pt.4 Ch.6 Sec.5 G102
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
ORO Manual ( Oil Recovery Operation ) DnV Pt.5, Ch. 7, Sec. 11 and NOFO Standard
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
641 Globe valve, flanged DN40 LK 467052 PN16 Cast iron Straight type LG2 LG2 LK 5566823 --> 356-357
641 Globe valve, flanged DN40 LK 467002 PN16 Ductile iron Straight type LG2 LG2 LK 5568423 --> 364-365
641 Globe valve, threaded 1/4"-1 1/2" LK 456022 PN16 LG2 LG2 LK 5573981 --> 349
641 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
641 Flange DN40 PN40 Steel NS2529 S235 JR (RSt. 37.2) 1254864 --> 44
641 Flange DN40 PN25 Steel NS2529 S235 JR (RSt. 37.2) 1254864 --> 44
641 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
641 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
641 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
641 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
641 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
641 Saddles Steel EN 10216-2 P235GH (St.35.8) To be avoided, limited use only 1207133 --> 31
641 Cu - Fittings Cu Viega
641 Penetration sealing CSD SLIPSIL
Clamps
641 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty/Insulated 3511806 --> 213
641 Clamp-Tico clip HT / CL DN50 Steel Tico Max working temp 150 deg C Installed between support and pipe
Gaskets
641 Supagraf Tanged T10 DN10 PN 100 Graphite 1,5 - 3,0 ASME B 16.5 James Walker Temperature range: -200 to +400
641 Copper tube ø8 Copper 0,8 N/A EN 1057 (NS1758) 25m coil 5002011
641 Copper tube ø10 Copper 1,0 N/A EN 1057 (NS1758) 5002201
641 Copper tube 1/2" ø12 Copper 1,0 N/A EN 1057 (NS1758) 5002202
641 Copper tube 1/2" ø15 89 Bar Copper 1,2 N/A EN 1057 (NS1758) 5002203
641 Copper tube 3/4" ø22 75 Bar Copper 1,5 N/A EN 1057 (NS1758) 5002211
641 Copper tube 1" ø28 58 Bar Copper 1,5 N/A EN 1057 (NS1758) 5002212
641 Copper tube 1 1/4" ø35 51 Bar Copper 1,5 N/A EN 1057 (NS1758) 5002213
641 Copper tube 1 1/2" ø42 42 Bar Copper 1,5 N/A EN 1057 (NS1758) 5002214
641 Pipe DN50 ø60,3 Steel 4,5 6,3 4,5 6,3 EN 10216-2 P235GH (St 35.8) 1113227/1113293 4
641 Pipe DN65 ø76,1 Steel 4,5 6,3 4,5 6,3 EN 10216-2 P235GH (St 35.8) 1113953/1114019 4
641 Pipe DN80 ø88,9 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1114393/1114503 4
641 Pipe DN100 ø114,3 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115009/1115119 5
641 Pipe DN125 ø139,7 Steel 4,5 8,0 4,5 (8,0) Bending tool N/A EN 10216-2 P235GH (St 35.8) 1115603/1115713 5
641 Pipe DN150 ø168,3 Steel 4,5 8,8 4,5 8,8 EN 10216-2 P235GH (St 35.8) 1101066/1116263 5
641 Pipe DN200 ø219,1 Steel 6,3 8,8 6,3 8,8 EN 10216-2 P235GH (St 35.8) 1101099/1116659 5
641 Pipe DN250 ø273,0 Steel 6,3 8,8 DN250 Bending N/A EN 10216-2 P235GH (St 35.8) 1101122/1116923 5
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
701-101 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only using to 1254629 --> 43
701-101 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) pipe-dim.>40 & upwards 1254429 --> 42
701-101 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
701-101 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
701-101 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
701-101 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
701-101 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
701-101 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
Clamps
701-101 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
701-101 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
Gaskets
701-101 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
701-102 HPL tube ø12 218 bar Crom 6 free 1,5 E235N St 37.4 GS Hydro
Gaskets
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
703 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only for DN>40 1254629 --> 43
703 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
703 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
703 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
703 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
703 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
703 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
703 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
703 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
703 Saddles Steel EN 10216-2 P235GH (St.35.8) Limited use only 1207133 --> 31
Gaskets
703 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
703 Precision tube ø8 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120089 7-9
703 Precision tube ø12 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120164 7
703 Precision tube ø15 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120254 7
703 Precision tube ø18 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120377 7
703 Precision tube ø22 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120633 7
703 Precision tube ø28 PN10 Steel 2.0 N/A EN 10305-4 E235 (St.37.4) 1120877 7
703 Precision tube ø35 PN10 Steel 2,5 N/A EN 10305-4 E235 (St.37.4) 1121311 7
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
707 Flange Fittings acc. to LNG tank syst/eng supplier
707 Flange
707 T-pipe
707 T-pipe reducer
707 Reducer concentric
707 Elbow
707 Union ø6 - ø30 PN100 - 400 Aisi316 Fittings acc. to LNG tank syst/eng supplier
707 Elbow ø6 - ø30 PN100 - 400 Aisi316
707 Tee ø6 - ø30 PN100 - 400 Aisi316
Gaskets
Gaskets
711 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
721 Welding collar DN25-DN600 PN10/16 CuNi DIN 86037 CUNI 90/10 130
721 Saddle DN25-DN300 PN10 CuNi DIN 86087 CUNI 90/10 See General Remarks 128
721 Elbow DN25-DN600 PN10 CuNi DIN 86090 CUNI 90/10 127
721 Socket, withworth tread 1/4"-2" CuNi DIN 86103-B CUNI 90/10 Threads inside 131
721 Socket, welding ends 1/4"-2" CuNi CUNI 90/10 Threads outside 131
Clamps
721 Clamp NS 5553 Omega Clamp Galv. with rubber Steel / CuNi pipes
Gaskets
721 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
721 Pipe DN25 ø30.0 PN10 CuNi 1,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017549 126
721 Pipe DN32 ø38.0 PN10 CuNi 1,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017563 126
721 Pipe DN40 ø44.5 PN10 CuNi 1,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017572 126
721 Pipe DN50 ø57.0 PN10 CuNi 2,0 N/A DIN 86019 CUNI 90/10 Open comp. Ø57x2,0 can be cold bent 5017589 126
721 Pipe DN65 ø76.1 PN10 CuNi 2,0 N/A DIN 86019 CUNI 90/10 Open compartments 5017598 126
721 Pipe DN80 ø88.9 PN10 CuNi 2,0 N/A DIN 86019 CUNI 90/10 Open compartments 5017607 126
721 Pipe DN100 ø108 PN10 CuNi 2,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017616 126
721 Pipe DN125 ø133 PN10 CuNi 2,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017621 126
721 Pipe DN150 ø159 PN10 CuNi 2,5 N/A DIN 86019 CUNI 90/10 Open compartments 5017629 126
721 Pipe DN200 ø219.1 PN10 CuNi 3,0 N/A DIN 86019 CUNI 90/10 Open compartments 5017643 126
721 Pipe DN250 ø267.0 PN10 CuNi 3,0 N/A DIN 86019 CUNI 90/10 Open compartments 5017652 126
721 Pipe DN300 ø323.9 PN10 CuNi 4.0 N/A DIN 86019 CUNI 90/10 Open compartments 5017665 126
721 Pipe DN350 ø368 PN10 CuNi 4,0 N/A DIN 86019 CUNI 90/10 Open compartments 5017672 126
721 Pipe DN400 ø419 PN10 CuNi 4,0 N/A DIN 86019 CUNI 90/10 Open compartments - - On request
721 Pipe DN450 ø457 PN10 CuNi 4,5 N/A DIN 86019 CUNI 90/10 Open compartments - - On request
721 Pipe DN500 ø508 PN10 CuNi 5,0 N/A DIN 86019 CUNI 90/10 Open compartments - - On request
721 Pipe DN600 ø610 PN10 CuNi 5,0 N/A DIN 86019 CUNI 90/10 Open compartments - - On request
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
GENERAL REMARKS:
EPDM gaskets and seals to be used
Cromium fittings to be used on all precision steel pipes - EN 10305 / DIN 2391
All valves on deck - AISI316 handle and plate
Grooved couplings to be used as much as possible on pipe dimensions DN50 (as a minimum instead of flange to flange connection between pipes)
Remote operated valves to be controlled from ECR
All pumps to be fitted with pressure gauges on inlet/outlet side
Vent. to exp.tanks to be located from high loops in the systems where air can accumulate
The end of the probe to be installed as close as possible to the center of flow path. To be mounted 1m away from the valves and min. 1m away from any junction on the pipe
Nylock nuts to be used on connection flange for all components mounted on vibration pads
Steel ring between flange and rubber compensator to be used
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
722 Butterfly valve, lug DN50 EGO PN 10 Ductile iron Lever / gear operated AISI431 A351-CF8M EPDM -20 +120 EGO 5521301 --> 304-305
722 NR valve, wafer DN50-DN300 Fig. 2401 PN16 Cast iron Duo check A351-CF8M NBR -10 100 Genebre 5551597 --> 408
722 NR valve closable DN40 LK 467052 NR PN 10 Cast iron Straight type LG2 LG2 +120 LK 5540023 --> 426-427
722 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
722 Flow reg. valve, threaded 3/8" - 2" STAD PN16 AMETAL Straight type AMETAL LG2 EPDM -20 +120 TA Hydronics 8522303 --> 298
722 Flow reg. valve, flanged DN65 - DN150 STAF PN16 GG25 Straight type AMETAL LG2 EPDM -20 +120 TA Hydronics 8521951 --> 299
722 Y-strainer, threaded 3/8"-2" CIM 74-A 20 bar Bronze St.St. strainer -10 +100 Cim 4015502 --> 470
722 Pressure relief valve, threaded 3/8"-2" Götze 618 T 12 bar Gunmetal Angled. Set-pressure: x bar (specify at order) PTFE +225 GÖTZE 5621756 --> 446
722 3-way thermostatic reg. valve, wax type DN40 AMOT model B PN 10 Cast iron … …
722 Deaerator 1/2" Flamco Flexvent Super 10 bar Bronze -10 +120 Flamco Air vent for high points in the system
722 Pressure reducing valve, threaded 1/4"-2" D22, Habedo 40 bar Brass +70 Habedo 5627103 --> 440
722 Hose coupling PN16 Ca.Ir.
722 Liquid level indicator WEKA
722 Orifice AISI316
722 NR valve, threaded 3/8"-2" LK 470022 PN16 LG2 Straight type LG2 LG2 LK 5546842 --> 417
722 Flex hose coupling PN16 EPDM Rubber w/AISI316 flange EPDM
722 Flex.rubber bellow T-50 PN16 EPDM Rubber w/steel flange EPDM 8541303 --> 454
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
722 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar Steel Victaulic EPDM gasket (green stripe)
722 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
722 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
722 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
722 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
722 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
722 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
Clamps
722 Clamp HD Galv. Flat-bar heavy duty Steel pipes 3511806 --> 213
722 Clamp HD Galv. U-bolt Steel pipes 3477153 --> 221
722 Clamp DIN3015 Part 1 Polypropylen (PP) Prec.steel pipes
Gaskets
722 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
722 Pipe DN50 ø60,3 PN10 AISI316L 2,0 N/A EN 10217-7 AISI316L Convert
722 Pipe DN65 ø76,1 PN10 AISI316L 2,0 N/A EN 10217-7 AISI316L Convert
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
731 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only using to 1254629 --> 43
731 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) pipe-dim.>40 & upwards 1254429 --> 42
731 Clamp DIN3015 Part 1 Polypropylen (PP) Prec.steel pipes
731 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
731 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
731 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
731 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
731 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
Clamps
731 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
731 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
Gaskets
731 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
740 Gasket Supergraf Laminated S10 2,0 ASTM F36A James Walker 14 J.Walker
740 Pipe DN100 ø114,3 St. steel 2,0 N/A EN 10217-7 AISI 316L 140
740 Pipe DN125 ø139,7 St. steel 2,0 N/A EN 10217-7 AISI 316L 140
740 Pipe DN150 ø138,3 St. steel 2,0 N/A EN 10217-7 AISI 316L 140
740 Pipe DN200 ø219,1 St. steel 2,0 N/A EN 10217-7 AISI 316L 140
740 Pipe DN250 ø273,0 St. steel 2,6 N/A EN 10217-7 AISI 316L 140
740 Pipe DN300 ø323,9 St. steel 2,5 N/A EN 10217-7 AISI 316L 140
740 Pipe DN400 ø406,0 St. steel 3,0 N/A EN 10217-7 AISI 316L 139
740 Pipe DN450 ø456,3 St. steel 3,0 N/A EN 10217-7 AISI 316L 139
740 Pipe DN500 ø506,0 St. steel 3,0 N/A EN 10217-7 AISI 316L 139
740 Pipe DN600 ø606,0 St. steel 3,0 N/A EN 10217-7 AISI 316L 139
740 Pipe DN700 ø711,0 St. steel 4,0 N/A EN 10217-7 AISI 316L
740 Pipe DN800 ø813,0 St. steel 4,0 N/A EN 10217-7 AISI 316L
740 Pipe DN900 ø914,0 St. steel 4,0 N/A EN 10217-7 AISI 316L
740 Pipe DN1000 ø1016,0 St. steel 4,0 N/A EN 10217-7 AISI 316L
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
801 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only for DN>50 1254629 --> 43
801 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
801 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe)
801 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
801 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
801 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
801 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
801 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
801 Saddles Steel EN 10216-2 P235GH (St.35.8) 1207133 --> 31
801 FIG206FM/FIG50FM
Clamps
801 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
801 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
Gaskets
1207133 --> 31
801 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
1207133 --> 31
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
803 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
803 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
803 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe)
803 T-pipe Steel EN 10253-2 P235GH (St.35.8)
803 Elbow Steel EN 10253-2 P235GH (St.35.8)
Clamps
803 Clamp HD Galv. Flat-bar heavy duty Steel pipes 3511806 --> 213
803 Clamp HD Galv. U-bolt Steel pipes 3477193 --> 221
803 Clamp DIN3015 Part 1 Polypropylen (PP) Prec.steel pipes
803 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
804 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
804 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
804 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
804 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
804 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
804 Saddles Steel EN 10216-2 P235GH (St.35.8) 1207133 --> 31
Gaskets
804 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
GENERAL REMARKS:
Fire pumps to have remote start from the bridge
All pumps to be arranged with pressure/vacuum gauge on suction and discharge
Connecting sleeves are not allowed on overboard pipes with substantial thickness (DNV 4.6.7 F103)
Overboard valves size DN 125 and bigger to have DNV product certificate acc. to DNV 4.6.7 C301.
Pipes to be galvanized steel pipes. The galvanizing of the pipes are to be executed after all fabrication are finished
All joints within tanks shall be welded, with expansion or contraction provided for by bends.
Final location of hydrants to be subject for approval on the fire control plan
All fire hose coupling to be of "STORZ C" type
Sensors to be placed in AISI316 steel pockets
International shore connection to be arranged on main deck
Pipes and valves mounted on shell plating, bottom and sea chests are to be delivered with doc. The wallthickness between ships side and first inboard valve to be in accordance with DnV rules
Steel ring between flange and rubber compensator to be used
Nylock nuts to be used on connection flange for all components mounted on vibration pads
STANDARD MTO - ARMATURES INTERNAL INFO - BD catalogue vol.F references
Export to Armature List Additional information
SFI DESCRIPTION SIZE * TYPE PRESSURE BODY REMARKS STEM DISC SEAT TEMP. RANGE (°C) TYPICAL TYPICAL NRF NO. PAGE NOTE
RATING min max MANUFACTURER USE NUMBER
813 Butterfly valve, lug DN40-DN600 PN16/PN10 Ductile iron Type A = Bare shaft, Actuator operated AISI316 AlBr NBR -15 +80 EGO 5521362 --> 306-307
813 Butterfly valve, lug DN40-DN200 PN16/PN10 Ductile iron Type B = Lever operated AISI316 AlBr NBR -15 +80 EGO 5521377 --> 306-307
813 Butterfly valve, lug DN200-DN600 PN10 Ductile iron Type C = Gear operated AISI316 AlBr NBR -15 +80 EGO 5521386 --> 306-307
813 Butterfly valve overboard, lug DN40-DN100 LK 710702 PN16 Ductile iron Lever or actuator operated. AISI316 AlBr NBR -15 +80 LK Overboard valve
813 Butterfly valve overboard, lug DN125-DN300 LK 710702 PN16 Ductile iron Lever or actuator operated. DNV cert. AISI316 AlBr NBR -15 +80 LK Overboard valve
813 Mud box, flanged DN40 LK 482051 4 bar Cast Iron Straight type. Strainer in St.Steel +80 LK 4017462 --> 476
813 Mud box, flanged DN40 LK 482151 4 bar Cast Iron Angle type. Strainer in St.Steel +80 LK 4017512 --> 477
813 NR valve , wafer DN40-DN250 LK 300702 PN16 Cast iron Duo check AISI316 AlBr NBR -10 +80 LK
813 NR valve, threaded 3/8" - 2" LK 470022 16 bar LG2 LG2 LG2 LK 5546842 --> 417
813 NR valve closable, flanged DN40 LK 467052 NR PN 10 Cast iron Straight type LG2 LG2 +120 LK 5540023 --> 426-427
813 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
813 Fire valve, flange/threaded DN40-DN65 LK 356622 PN16 RG5 Straight type SM2065 RG5 NBR LK 5578504 376-377
813 Fire valve, flange/threaded DN40-DN65 LK 356722 PN16 RG5 Angle type SM2065 RG5 NBR LK 5778514 376-377
813 Fire coupling DN40-DN65 PN16 Brass NOR & STORZ 378
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
813 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) 1254629 --> 43
813 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
813 Grooved coupling, flexible DN50-DN200 Style 75 31-34 Bar HD Galv. Victaulic Nitril gasket (orange stripe)
813 Grooved coupling, rigid DN50-DN250 Style 07 34,5-41,4 bar HD Galv. Victaulic Nitril gasket (orange stripe)
813 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
813 T-pipe reducer Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
813 Reducer concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
813 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
Clamps
813 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
813 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
813 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
814 Butterfly valve, lug DN350 PN10 GGG40.3 FiFi 1. Overboard valve to be DNV cert.
814 Butterfly valve, lug DN50-350 PN16 GGG40.3 FiFi 1
814 Ball valve, threaded 1/4" - 2" Haitima 2006 64 bar A351-CF8M A276-316 A351-CF8M PTFE -20 +200 Haitima (EGO) 5605353 --> 256-257
814 NR valve, wafer DN50 PN16 GGG40.3 FiFi 1
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
814 Grooved coupling, flexible DN350-DN600 W77 AGS 20 bar Ductile iron Victaulic EPDM gasket (green stripe)
814 Flange DN350 Slip on Flg PN10 St 37.2 EN10204/2.2 NS2526 FiFi 1 Suction
814 Flange DN600 Weldneck PN25 C.22.8 EN 1092-2 FiFi 2
814 Flange DN50-150 Slip on Flg PN16 St 37.2 EN10204/2.2 NS2527
814 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
814 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
814 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) <DN150, 3 step >DN125, 2 step down 1214621 --> 30
814 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
Clamps
814 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty + additional foundations Main lines to monitors additional found 3511806 --> 213
Gaskets
814 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING NUMBER
General Tank Overboard Norm Grade TYPICAL
821 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only for DN>50 1254629 --> 43
821 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2) 1254429 --> 42
821 Grooved coupling, rigid DN50-DN300 Style 07 27,6-41,4bar HD Galv. Victaulic Nitril gasket (orange stripe) When dismountable connection is necessary
821 T-pipe Steel EN 10253-2 P235GH (St.35.8) 1210411 --> 29
821 Elbow Steel EN 10253-2 P235GH (St.35.8) 1150766 --> 22
821 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8) 1214621 --> 30
821 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8) 1211822 --> 26-27
821 End Cap Steel EN 10028-2 P265GH 1208404 --> 33
821 Saddles Steel EN 10216-2 P235GH (St.35.8) 1207133 --> 31
Clamps
821 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty 3511806 --> 213
821 Clamp - Steel pipes HD Galv. NS5550 U-bolt 3477153 --> 221
Gaskets
821 Gasket INCA BS 7531 DN 10 80 Bar Aramid&Nitril 1,5-2,0 NS 157 James Walker Compressed non asbestos fibre
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING
General Tank Overboard Norm Grade TYPICAL NUMBER
822 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2)
822 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2)
822 Flange DN150 PN16 Steel NS2538
Gaskets
STANDARD MTO - HPL TUBES: See table in STD-831-102 (High Pressure Hydraulic Systems)
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
RATING General Tank Overboard Norm Grade TYPICAL NUMBER
831-101 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only for DN>50
831-101 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2)
831-101 MFAS Flange DN50-DN250 PN64 Steel EN 10025 SS132134(St 52,3)
831-101 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty
831-101 Clamp - Steel pipes HD Galv. NS5550 U-bolt
831-101 T-pipe Steel EN 10253-2 P235GH (St.35.8)
831-101 Elbow Steel EN 10253-2 P235GH (St.35.8)
831-101 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8)
831-101 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8)
831-101 Bleed Plug M22x1,5 CuZn39Pb330B
831-101 Bleed Plug Socket M22x1,5 Steel Used also as a video inspection points
831-101 Dowty ring ø20,5x2,5 ø32 -outside diameter Steel/Rubber
Gaskets
* DN sizes are for flanged armatures. Inch (") sizes are for threaded armatures.
STANDARD MTO - FITTINGS INTERNAL INFO - BD catalogue vol.F references
SFI DESCRIPTION SIZE TYPE PRESSURE RATING MATERIAL THICKNESS (mm) STANDARD MANUFACTURER REMARKS TYPICAL USE NRF NO. PAGE NOTE
General Tank Overboard Norm Grade TYPICAL NUMBER
831-102 Flange DN150 PN16 Steel NS2527 S235 JR (RSt. 37.2) Flange conn.only for DN>50
831-102 Flange DN200 PN10 Steel NS2526 S235 JR (RSt. 37.2)
831-102 MFAS Flange DN50-DN250 PN64 Steel EN 10025 SS132134(St 52,3)
831-102 Clamp - Steel pipes HD Galv. NS5553 Flat-bar heavy duty
831-102 Clamp - Steel pipes HD Galv. NS5550 U-bolt
831-102 T-pipe Steel EN 10253-2 P235GH (St.35.8)
831-102 Elbow Steel EN 10253-2 P235GH (St.35.8)
831-102 Reducing T-pipe Steel EN 10253-2 P235GH (St.35.8)
831-102 Reducing Concentric Steel EN 10253-2 P235GH (St.35.8)
831-102 Bleed Plug M22x1,5 CuZn39Pb330B
831-102 Bleed Plug Socket M22x1,5 Steel Used also as a video inspection points
831-102 Dowty ring ø20,5x2,5 ø32 -outside diameter Steel/Rubber
Gaskets
S/L HPL TUBE ø6 525 Aisi 316 1,0 AISI-316L AISI-316L 0610316L
S/L HPL TUBE ø12 379 Aisi 316 1,5 AISI-316L AISI-316L 1215316L
L HPL TUBE ø15 297 Aisi 316 1,5 AISI-316L AISI-316L 1515316L
S HPL TUBE ø16 379 Aisi 316 2,0 AISI-316L AISI-316L 1620316L
L HPL TUBE ø18 333 Aisi 316 2,0 AISI-316L AISI-316L 1820316L
S HPL TUBE ø20 279 Aisi 316 2,0 AISI-316L AISI-316L 2020316L
L HPL TUBE ø22 268 Aisi 316 2,0 AISI-316L AISI-316L 2220316L
S HPL TUBE ø25 364 Aisi 316 3,0 AISI-316L AISI-316L 2530316L
L HPL TUBE ø28 207 Aisi 316 2,0 AISI-316L AISI-316L 2820316L
S HPL TUBE ø30 298 Aisi 316 3,0 AISI-316L AISI-316L 3030316L
L HPL TUBE ø35 209 Aisi 316 3,0 AISI-316L AISI-316L 3530316L
S HPL TUBE ø38 316 Aisi 316 4,0 AISI-316L AISI-316L 3840316L
L HPL TUBE ø42 207 Aisi 316 3,0 AISI-316L AISI-316L 4230316L
Low HPL TUBE ø50 172 Aisi 316 3,0 AISI-316L AISI-316L 5030316L
High HPL TUBE ø50 297 Aisi 316 5,0 AISI-316L AISI-316L 5050316L
Low HPL TUBE ø60 142 Aisi 316 3,0 AISI-316L AISI-316L 6030316L
High HPL TUBE ø60 244 Aisi 316 5,0 AISI-316L AISI-316L 6050316L
This document is the property of the Vard Group AS with its subsidiaries. It is protected by copyright, intellectual property rights and marketing laws.
The document and the design and technical solutions expressed by the document may not be copied, distributed or otherwise used without the express, written consent of Vard Group AS.