Professional Documents
Culture Documents
doc
Debugging Manual
Dec 2014
1 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Change Record
Serial Change of Date of Change
Numbe Content of Change Changed by
PC No. of
r
1 PM13661 New Archive 2013.10.25 XuJun
2 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Contents
1.Overview...................................................................................................................... 3
6 Inspection mode....................................................................................................19
10 Learn Run..............................................................................................................23
11 Normal Operation.................................................................................................23
14 Trouble shooting...................................................................................................25
3 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
1.Overview
HAMCB (Logic Control Board) as the core of the elevator control system and uses serial
communication system of high reliability to closely connect all parts of the elevator. The drive
part adopts the high-precision vector frequency transformation technology which makes the
elevator run more stably and comfortably; besides, the smooth and compact appearance is
visually striking.
In the HAMCB, there are four module subsystems, namely:
OCSS (Operation Control Subsystem)
MCSS (Movement Control Subsystem)
DCSS (Door Control Subsystem)
DBSS (Drive and Brake Subsystem)
Well Signal
Door Drive
Machine
ALMCB功能框图
HAMCB Functional
Diagram
4 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
The following is the HS-EVC control system’s basic diagram and signal flow graph.
5 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Attention: when testing the insulation resistance, make sure to pull out the plug on
the electronic board to avoid damaging the board.
6 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Make sure that the ERO switch on the controller is at the emergency run position.
Make sure that all landing doors and car doors are closed correctly.
Turn on the main power switch.
Observe the indicator on the HAMCB electronic board and check that the input signal is
correct:
7 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Indicator Explanation
RUN Flicker: normal remote serial line and the watchdog
+5V On: normal power supply (5V).
DZ On: The car is within the door zone.
DOB On: The door reversing device (front or back door) is operated.
DOL On: Reach door fully open switch
DFC On: closure of door lock and safety chain
DW On: closure of the car door
ES On: emergency button action
Note: After powering on, check relevant circuits and parameters (generally,
parameters have already been set before delivery of the elevator) if the status of the
indicator is inconsistent with that listed in the above table.
All installation parameters and I/O parameters of HAMCB have been set before the
delivery; please refer to HAMCB parameter table for details.
NOTE:If you find that there is a big difference between the IO settings and electrical
schematics address table, need to perform the logical part of the parameter
initialization, Enter the menu M1-7, enter the password 654321, select the IO setup
options, generally, the operation has been set at the factory, this menu should be
with caution on the construction site!
8 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Relvel?s times
M-1-3-1-3
DOOR Front Door machine 5 5 means opening and
type closing is controlled by
switch parameter.
12 means door signal is
controlled by ST
parameter.
REAR REAR Door machine 0 5 means opening and
operation closing is controlled by
switch parameter.
12 means door signal is
controlled by ST
parameter.
LR-T Illumination off delay 240 0-255
LR-MODE Illumination delay 0 0 means LR-T valid when
operation type the door been closed only.
1 means LR-T valid
whenever door been
closed or opened.
F:DOL-D DOL signal input 0 0-255
definition
F: EN-DCL Front door DCL 1 0 means DCL detecting
detecting Enable negative
1 means DCL detecting
positive
EN-DDO Double passed doors 0 0 means only Front door
Enable or REAR door exist
NO. IN 1LS DZ numbers in 1LS 1 1、2
NO. IN 2LS DZ numbers in 2LS 1 1、2
M-1-3-1-4
GRP-NO Group number 1 1-8
GROUP Group elevator 1 1-8
numbers
NoDW_Chk DW detecting Enable 1 0、1
9 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Press 1 to monitor the drive status; the second level menu of the monitoring is shown
as in the diagram 4;
10 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
11 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
0: UVW
square wave
increment
Encoder sort Encoder sort 1 sort
M3-3-
1-1 1: SINCOS
sine and
cosine
12 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
13 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
0~1,0 means
M3-3- Brake switch non-
Brk SW pres 1
1-3 detecting detecting,1mean
s detecting
14 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
15 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
16 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
17 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
18 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Start
开始
Set encoder
设置编码器参数 parameters
Set motor
设置马达参数parameters
Set mechanical
设置机械参数 parameters
Finish
完成
19 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
6 Inspection mode
6.1Emergency Run Operation (ERO)
Check that the controller emergency run operation switch (ERO) is at the inspection position
and the car top inspection switch (TCI) is at the normal position.
Use the server to observe (M-1-1-2) the status of input tci, uib, dib and ero, at this time, the
server shall display "tci uib dib ERO".
Inch the up motion button on the ERO box, "uib" displayed on the server shall turn into
?1?,means there is signal input.
Inch the down motion button on the ERO box, "dib" displayed on the server shall turn into ?1?.
20 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Note: The distance here refers to the distance when the contact of the limit switch
opens, but not the distance when the limit switch wheel presses the connecting rod.
21 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
NO RLV
RLV
Magnetism switch
Install and adjust positions of 2 leveling devices, make them have a distance of 60mm, and
perpendicular to each other, and ensure the magnetic switch is installed in sequence of 1LV and
2LV from top to bottom. Install the magnetic strip of each floor in the guide rail, to make it located
in front of magnetic switch, and ensure the distance within 20mm from the surface of magnetic
strip to the magnetic switch. If re-leveling function is provided, it requires installing two magnetic
switches, i.e. UIS and DIS . See following drawing.
22 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
magnetic
strip
.NO RLV
magnetic
strip
RLV
8.2.1 Put the balanced load into the car (about 45% load)
8.2.2 Adjust positions of the 2 level photo-electric switches (1LV: upper level photo-electric switch;
2LV: lower level photo-electric switch), leave about 60mm between the two switches, make
them be vertical and make sure that the photo-electric switches installed from top to bottom
are 1LV and 2LV respectively.
8.2.3 Operate the elevator to the level position of each floor.
8.2.4 Adjust the light proof flashboard of each floor and make its center line conform to the center
23 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
line of the two photo-electric switches (namely, the center line is 30mm from both 1LV and
2LV). The operation will affect the level precision.
10 Learn Run
10.1 Before the learn run, use ERO to make whole journey operation and use the server to
observe and ensure that the well photo-electric and forced slow down switch signals are
normal.
10.2 When the elevator at the level position, DZ, 1LV and 2LV shall be ?1?; when the elevator
runs downwards, 2LV acts first, therefore, 2LV and DZ turn into ?0?. The upward running is
on the contrary.
10.3 When the elevator is near the bottom floor, 1LS acts and 1LS turns into ?1?; when the
elevator is at the top floor, 2LS acts and 2LS turns into ?0?; when the elevator is at the
middle floor, 1LS and 2LS shall be ?1?.
10.4 Confirm that "RUN ENABLE" parameter in the M-3-3-1-9 of HAMCB drive part shall be 0
and "RUN SOURCE SVT" in M3-3-5 of HAMCB drive part shall be 1.
10.5 Push ERO and TCI to the normal position and use the server to operate the drive part M-3-
3-4 to start the learn run.
10.6 The car will run to bottom floor in low speed, and go up in learn run speed. When the car
reaches the top floor level, the learn run finished.
10.7 After the successful learn run, set the "RUN ENABLE" parameter to 1. The learn run
parameter stores in M-3-1-4 menu.
11 Normal Operation
11.1 Check according to the connection diagram that the address of remote station RS5 and the
pin connection are correct.
11.2 Connect the server to the SVT server interface on the HAMCB board, ensure in
accordance with the parameter table and the input and output table of the I/O interface
that all parameters in the EEPROM and I/O addresses are correct.
11.3 Use the server to input the call signal.
11.4 Press in order the server's M-1-1-1, then input the call signal and press the number key of
the floor that needs the call. (Key "0" for the first floor, key "1" for the second floor, and so
on)
11.5 By pressing the blue key and then the "ENTER" key, the elevator will run to the call floor.
24 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
11.6 Check that all functions involved with RS5 and RSEB work normally.
11.7 Use the server to exclusively operate the Car speed in M-3-1-1 and monitor from the drive
that the elevator runs at the speed specified in the contract. Quence in time when the
elevator normally run is shown in Picture 5;The operation curve is shown in Picture6.
25 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
14 Trouble shooting
Enter M1-2-1 check logical fault,press GOON button to turn to saved fault page,press 1,2
button at the same time to delete a fault,repeat to press 1,2 ,deleting all faults.
enter M3-2-1 CURRENT FAULT check the current fault;
enter M3-2-2 SAVE FAULT to check the save fault;
26 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
14.2 Inching operation button,contactor,brake relay and brake open normally,motor doesn?t
revolve , electric current so large ?Drive Overload?.
Maybe the problem is the phase sequence that the inverter reaching to the motor is
wrong, we should connect the motor line based on correct ways.
14.3 After self-learning to the top level,the elevator can not work normally.
Check ?run enable? ,should turn into ?1?,in addition please check well signal whether
being normal.
14.4 common drive fault
t
Number Fault name Possible cause or explanation
1 PVT Lost Encoder fault. Wrong setting of encoder type or
encoder connection problems or the band-type
brake is not open during the positioning process.
2 Over Current Drive over current fault, see note 1
3 Motor Overload Motor overload fault, see note 1
4 Drive Overload Drive overload fault, see note 1
5 DC Link OVT Over voltage fault, an alarm occurs when the bus
bar voltage is higher than DC780V, the fault is
automatically cleared when the bus bar voltage is
lower than DC760V
6 Power Lost Under voltage fault, occurring when powering on or
inputting voltage lower than AC380V
7 Track err Speed tracking error. The difference value between
the actual operation speed and the given operation
speed exceeds the set value range of "Track error"
in M3-3-1-2, or the positioning of the encoder poles
is inaccurate.
8 Mtr therml cntct Motor thermistor act
9 DBD Pickup Main contactor or band-type brake contactor
feedback fault
10 Brake dropped Machine band-type brake switch feedback fault
11 DDP Fault Photo-electric abnormal status. DZ signal remains
unchanged and exceeds the set value of DDP time
in M3-3-5.
12 1LV/2LV normal A photo electricity normal open fault, 1LV/2LV
Closed photo electricity normal open
27 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
28 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
29 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
30 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
31 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
288 DHL 00 Down Hall Lantern 00 1242 OTLH Outgoing Traffic Light
Hall
480 CPC 00 Car Position Contact 00 1251 ERL Express Running Light
32 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
543 CPC 63 Car Position Contact 63 1253 NSLH Non Stop Light Hall
544 RCB 00 / Rear Car Button 00 / Rear 1254 ARL Auto Running Light
RCTTL 00 Tell Tale Light 00
607 RCB 63 / Rear Car Button 63 / Rear 1256 SROS Separate Riser Operation
RCTTL 63 Tell Tale Light 63 Switch
608 RUHB 00 / Rear Up Hall Button 00 / Rear 1257 ISTS Intermittent Stop Switch
RUHTTL 00 Up Hall Tell Tale Light 00
671 RUHB 63 / Rear Up Hall Button 63 / Rear 1259 DHBL Door Hold Button Light
RUHTTL 63 Up Hall Tell Tale Light 63
672 RDHB 00 / Rear Down Hall Button 00 / 1260 RDHBL Rear Door Hold Button
RDHTTL 00 Down Hall Tell Tale Light 00 Light
735 RDHB 63 / Rear Down Hall Button 63 / 1262 CHMU Chime Board Up Direction
RDHTTL 63 Down Hall Tell Tale Light 63
736 RUHL 00 Rear Up Hall Lantern 00 1263 SHBUZ Shabat Operation Door
Buzzer
799 RUHL 63 Rear Up Hall Lantern 63 1264 SHLH Shabat Operation Light
Hall
800 RDHL 00 Rear Down Hall Lantern 00 1265 PCLK 1 Park Car Clock 1
33 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
3
1055 SEC 63 Card Reader Security ( hall ) 1276 CSA 4 Car Secure Access Button
63 4
1056 RDOL Rear Door Open Limit 1277 CSA 5 Car Secure Access Button
5
1057 RDOB Rear Door Open Button 1278 CSA 6 Car Secure Access Button
6
1058 REDP Rear Electronic Door 1279 CSAC Car Secure Access Clear
Protection Switch
1059 RDCB Rear Door Close Button 1280 CSAK Car Secure Access
Keyswitch
1060 ATK Attendant Key Switch 1281 CSAL Car Secure Access Light
1061 HUDL Hall Up Direction Light 1282 GSAK Group Secure Access
Keyswitch
1062 HDDL Hall Down Direction Light 1283 GSAL Group Secure Access
Light
1063 GCB Up General Control Button 1284 AEFO Alternative EFO
1064 DDP Car Motion Control Signal 1285 ASLDOB Alternative Service
Landing DOB
1065 PKL Parking Light 1286 EFODOB Emergency Fireman
Operation DOB
1066 DCP Delayed Car Signal 1287 XEFO Override EFO
1073 ROLS Rear Over Load Signal 1294 APC 6 Absolute Position
Contact 6
1074 ( RHEL ) res. for Rear Hosp. Emerg. 1295 TCIB Top of car Inspection
Light Button
1075 RFSL Rear Fireman Service Light 1296 PDS Partition door Switch
34 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
1076 RCUDL Rear Car Up Direction Lantern 1297 CMR CAM Relay
1077 RCDDL Rear Car Down Direction 1298 DCDS Disable- Call - And -
Lantern Door Switch
1078 RHUDL Rear Hall Up Direction 1299 DCM Door Closing Management
Lantern
1079 RHDDL Rear Hall Down Direction 1300 RDCM Rear Door Closing
Lantern Management
1080 RIOTS Riot Operation Switch 1301 STOP Stop Signal
1084 RSTH Rear Stop signal hall 1305 LEV Level Signal for REM
1085 RSTC Rear Stop Signal Car 1306 - -
1086 MDD Passenger Move Detector 1307 PI7S-RA CPI-3 /HPI-3
1087 RMDD Rear Passenger Move Detector 1308 PI7S-RB CPI-3 /HPI-3
1091 CDLD Car Direction Lantern Down 1312 PI7S-RF CPI-3 /HPI-3
1093 CDGD Car direction Gong Down 1314 PI7S-LB CPI-3 /HPI-3
1094 RCDLU Rear Car Direction Lantern Up 1315 PI7S-LC CPI-3 /HPI-3
1095 RCDLD Rear Car Direction Lantern 1316 PI7S-LG CPI-3 /HPI-3
Down
35 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
(Generic Firemen
Service)
1102 ATTU Attendant Up Start Switch 1323 DDSR1 Disable DS Relay
(Generic Firemen
Service)
1103 ATTD Attendant Down Start Switch 1324 DEECR Disable EEC Relay
(Generic Firemen
Service)
1104 FDLU Further Demand Up Lantern 1325 DSGSR Disable SGS Relay
(Generic Firemen
Service)
1105 FDLD Further Demand Down Lantern 1326 UHDL 00 Up Hall Direction
Lantern 00
1108 INLC Independent Light Car 1390 DHDL 00 Down Hall Direction
Lantern 00
1110 CHCSC Cut Hall Call Signal Car 1453 DHDL 63 Down Hall Direction
Lantern 63
1111 CHCSH Cut Hall Call Signal Hall 1454 OOL 00 Out Of Order Light 00
1113 EPW Emergency Power Wait 1517 OOL 63 Out Of Order Light 63
1114 INS Car Inspection Signal 1518 DOC 00 Door Open Contact 00
1116 EHS Emergency Hospital Service 1581 DOC 63 Door Open Contact 63
1117 DOS / SGS Door Open Signal / Safety 1582 BCP1 Binary Coded Position
Gate Shoe
1118 RDOS / RSGS Rear Door Open Signal / Rear 1583 BCP2 Binary Coded Position
SGS
1119 LRD Light Ray Device 1584 BCP4 Binary Coded Position
1120 RLRD Rear Light Ray Device 1585 BCP8 Binary Coded Position
1121 XEPR Not able to rescue 1586 BCP16 Binary Coded Position
36 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
1122 CCOC Cut Car Calls for Car 1587 CPMT Car Position Message
Trigger
1123 CCOH Cut Car Calls for Hall 1588 DCMT Door Close Message
Trigger
1124 HCCO Hall Call Cut Off 1589 DOMT Door Open Message
Trigger
1125 GCCO Group Call Cut Off 1590 EMMT Emergency Message
Trigger
1126 CTLC Car to Landing / Car 1591 OLMT Overload Message Trigger
1127 CTLH Car to Landing / Hall 1592 DDMT Down Direction Message
Trigger
1128 ACSC Anti Crime Switch Car 1593 UDMT Up Direction Message
Trigger
1129 ACSH Anti Crime Switch Hall 1594 DNMT Door Nudging Message
Trigger
1130 CHCC Cut Hall Call Car 1595 1EFS 1st Emergency Fire
Service Car
1131 DFD Disable Front Doors 1596 2EFS 2nd Emergency Fire
Service Car
1132 DHB Door Hold Buttons 1597 EFOL Emergency Fire Operation
Light
1133 DRD Disable Rear Doors 1598 CRFL Car Returning to Floor
Light
1134 EFKB Emergency Fireman Key Bypass 1599 EFLM Emergency Fire Light
Machine Room
1135 EQS Earth Quake Switch 1600 EFLTC Emergency Fire Light Top
of Car
1136 EFO Emergency Fireman Operation 1601 CSABUZ Buzzer for Car Secure
Access
1137 ESH Emergency Service Hold 1602 AT20NDG Nudging for AT20
1138 ESK Emergency Service Keyswitch 1603 AT20RNDG Rear Nudging for AT20
1139 RB Reset Button 1604 LRTS (OKR) Light Ray Test Start
1140 RDHB Rear Door Hold Button 1605 LRCR Light Ray Check Relay
1141 AMCLK AM Clock Input 1606 RLRCR Rear Light Ray Check
37 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
Relay
1142 LPT Landing passing Tone 1607 LBG Light Beam Gate
1143 WCOS Wild Car Operation Switch 1608 RLBG Rear Light Beam Gate
1144 1MOTIM One more time signal 1609 ESBUZ Emergency Stop Buzzer
1145 ESSR Emergency Stop Switch Reset 1610 DDSRC Disable DS relay contact
(Korean Fire Service)
1146 CRV Cancel Relevelling 1611 DEMERC Disable Emergency relay
contact (Korea)
1147 ZR Front Door Zone Relay 1612 GSSI Group Successive
Starting In
1148 RZR Rear ZR 1613 GSSO Group Successive
Starting Out
1149 RNDG Rear Ndging Relay 1614 DDSR2 Disable DS relay 2
(Korea)
1150 ISPS Independent Service Park 1615 DMOOS Dot Matrix OOS (PI=5,6)
Switch
1151 CRC Card Reader Contact 1616 DMOLD Dot Matrix OLD (PI=5,6)
1152 SDB Special Door Open Button 1617 GPIN1 General Purpose input 1
1155 FPDL Fire Proof Door Light 1620 GPOUT2 General Purpose output 2
1156 AEPS Available for EPS Light 1621 GPIN3 General Purpose input 3
1160 SSM2 Speech Syn. Cmd. 2 1625 GPIN5 General Purpose input 5
1161 SSM3 Speech Syn. Cmd. 3 1626 GPOUT5 General Purpose output 5
1162 SSM4 Speech Syn. Cmd. 4 1627 1LV 1LV for CSP-5
1163 SSM5 Speech Syn. Cmd. 5 1628 2LV 2LV for CSP-5
1164 SSM6 Speech Syn. Cmd. 6 1629 TARGET enable DZ for CSP-5
1165 SSM7 Speech Syn. Cmd. 7 1630 LBGCHK Light Beam Gate Check
for CSP-5
1166 SSMB Speech Syn. Busy 1631 DOOR_ST1 ST1 for front DO2000
38 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
(DCSS5)
1167 SSMR Speech Syn. Reset 1632 DOOR_ST2 ST2 for front DO2000
(DCSS5)
1168 SSMS Speech Syn. Start 1633 DOOR_ST3 ST3 for front+rear
DO2000 (DCSS5)
1169 LPTB Landing Passing Tone Buzzer 1634 DOOR_ST1R ST1 for rear DO2000
(DCSS5)
1170 CTLPC CTL park close door 1635 DOOR_ST2R ST2 for rear DO2000
(DCSS5)
1171 CTLPO CTL park open door 1636 DOOR_ST3R ST3 for rear DO2000
(DCSS5)
1172 ULV Gamma L Speed dictation 1637 DDM Deenergize Door Motor
1173 RDZ Rear Door Zone 1638 RDDM Deenergize Rear Door
Motor
1174 CFSON Car Fireman Service On 1639 EFSL
1187 CPR Car Park Recognition REM 1660 LDOS Lobby Door Open Switch
1188 NORM Normal Operation for REM 1661 MAS Maintenance Access
Switch
1189 LDO Limited Door Open 1662 HCRC Hall Call Card Reader
39 的 40
C:\Users\chen.jun01\AppData\Local\Microsoft\Windows\INetCache\ \354756_537517\XT0223S13021.doc
1191 8LS2 Limit Switch 8LS2 for Hydro 1664 LNSL Load Non Stop Light
1192 LDT_ 5 50% of full load 1665 CCOL Car Call Cutoff Light
1193 C2_1IN C2 : bolt 1 position in 1666 HCOL Hall Call Cutoff Light
40 的 40