Professional Documents
Culture Documents
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.
Any previous data sheet issues have now become invalid. 738546 Page 1 of 1
www.kathrein.de
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
General Instructions
for Adjustment Mechanism
1
2
2
➀ Twist protection. ➀ Thread for fixing the protective To set the downtilt angle exactly,
➁ Downtilt spindle with integrated cap or the RCU (Remote Control you must look horizontally at the
scale. Unit). scale. The lower edge of the gear-
➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
0° – max.°
Remove the protective cap and the Set downtilt angle by rotating the Screw on the twist protection and
twist protection completely. gearwheel. the protective cap again.
For a description of RCU installation please refer to the respective data sheet.
www.kathrein.com Page 1 of 2
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
General Instructions
for Feederline and RCU Installation
for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
Adjustment mechanism
(protective cap removed) Ventilation hole
Colour coding:
Correlation of each RF input to:
– the corresponding adjustment mechanism
7-16 female (long neck) – the frequency range
– the polarization
32 | 1.3
Subject to alteration.
guidelines). 41
| 1.
1
These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifications, respectively the RCU nut
with a torque range of 15 – 18 Nm.
Page 2 of 2 Any previous data sheet issues have now become invalid.
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
4-Port Antenna Y1 Y2
Frequency Range 3300–3800 3300–3800
Dual Polarization X X
HPBW 65° 65°
Adjust. Electr. DT 2°–12°
set by hand or by optional RCU (Remote Control Unit)
Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.
1)
2)
(R) 3300-38
Y2 00
1 3 )/
(L
Y1
76 | 3.0
Y1 Y2
83 | 3.3
Y1 Y2
46 | 1.8
41 | 1.6
35 | 1.4
2 Left 4 Right
6 | 0.2
35 | 1.4 23 | 0.9
64 | 2.5 63 | 2.5
Bottom view
Dimensions in mm | inches
Correlation Table
Frequency range Array Connector
936.5061/a ngmn 04.21.06.01 Subject to alteration.
Y1 Y2
Left Right
Page 4 of 4 80010922 Any previous data sheet issues have now become invalid.
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820