Professional Documents
Culture Documents
1 2 3 4
MODBUS ADRESS
EN R/W Adr Data Description
TECHNICAL SPECIFICATIONS DIMENSIONS RW 0 Command Command Register
RW 1 RegA Extension for command
www.etarti.com A/D Converter RW 2 RegB Extension for command
Devices StatusA information bits
35x104x19mm Din rail type case
LDr Transmitter Minimum Input
Analog Input Range
0.02uV/Division
1mV/V - 10mV/V
0:Run/Error LED
1:Tare LED (0:No tare, 1:Tared)
RO 2:Stable LED (Display is stable)
Loadcell Input 350-1000 Ohm (Maxs. 12 Loadcells) / 3
Device StatusA
3:AbsZero LED (Display is Absolute)
LDr Rail type load cell converter.
Internal Resolution 24bits / 16.000.000 RW 4-7: N/A
Thanks to its small dimensions, it Measurement Speed 3840 samples/second 8-10: 3bit Decimal Point
11: N/A
provides the ideal solution for weight Loadcell Excitation 5Vdc 12-15: N/A 13-15: Unit 0:g,1:kg,2:t,3:N,4:kN,5:lb
and force applications in the panel. It Calibration Devices StatusB information bits
Cihaz DurumBitleri B Bilgi Bayrakları
enables Modbus RTU and ASCII Calibration Load calibration or digital calibration 0-2: N/A
communication up to 115200bps speed. Input/Outputs Device StatusB
3:x10 (0:Normal, 1:x10 Active)
RW 4 4:x10Dot(0:Normal, 1:Additional dot is on)
RS232 or RS485 communication is Outputs 3pcs transistor out(Optional hardware) 5:N/A (reserved)
offered as standard. With a standard Inputs 1adet optically isolated digital input 6:User In Menu (0:Normal, 1:User operation on
menu)
LDr transmitter, real sampling and Options 4/20mA - 0/10V Analog Output 7-15: N/A (reserved)
process output can be obtained up to Communication Devices StatusC information bits
0-7:Error Message (0-255 Screen Error Message)
960Hz speed. Communication 1 pcs RS232, 1pcs RS485 serial out. Device StatusC 8: N/A
RO 5
It can be monitored and recorded with [1200-115200bps] 9: Board Options DAC Module 0:No
Module,1:Module active
our DataViewer software. Modbus RTU / ASCII communication 10-15: N/A (reserved)
RW 6/7 Tare Tare Value
RO 8/9 Display Weight screen
Environments RW 10 DAC From DAC starting point as 0-
Supply/ Power 24V DC (+/- % 10) / 5W Maximum RW 11 DAC To DAC End point as 0-4095
Case/ Dimensions DIN Rail Type Aluminium, 35x104x19mm RW 12 DAC Current
4095Current output value of the DAC (0-4095)
12bits
Woriking Temperature -20/70°C RW 13 DAC Status DAC enable bit. 0:DAC is forced, 1:DAC is normal
Protection Class IP54 RW 14-15 Capacity Capacity of the device ( for Err-1 on Display)
RO 16-17 ADC Internal Internal real time measurement result
RO 18-19 ADC Filtered Filtered value. See GLOGIC and Sensor parameters
RO 20-21 mV/V mV/V value corresponding to load
RW 22-23 mV Cal Capacity Used for eCAL mV/V calibration calculation
RW 24 Counter Counts up 100ms
OPTIONS RO 88-89 Hold Value Last Hold value is shown when HOLD mode active
1:Hold active, 3:Drop down occurred (value has
RO 90 Hold Status
ANALOG OUTPUT: 0/10V ve 0-4/20mA Analog output dropped more than threshold value)
RW 91 Hold Threshold Threshold value for threshold type detections
Modbus Commands
DATA VIEWER SOFTWARE Address 0-1-2 are used to to special commands to device!!
Adr
Adr1 Adr2 Description
0
2 Adres Data Eeprom write, Reg1 Address, Reg2 Data. Cmd address 2.
With a standard LDr transmitter, real sampling and process 3 Adres Data Eeprom read. Reg1 Address and the result is seen on RegB.
4 - - Device reset command
output can be obtained up to 960Hz speed. 5 - - Zero operation. (Volatile, when power down the zero is cleared)
It can be monitored and recorded with our DataViewer 6 - - Tare operation. *when weight is differ from zero
7 - - Tare cancel opration. Tare cleared
software. 8 - - Device type read. Reg1 is shows device ID code, LDr family is 47604.
9 - - Device version read on Reg1. 107 = v1.0.7
10 - - Parameters are updated from eeprom to RAM
51 - - HOLD mode activated
52 - - HOLD mode de-activated
100 - - mV Capacity (23-24) and DAc Values (10-11) saved to Eeprom
Coefficient calibration. Reg1 and Reg2 is used to ented coefficient value.
To set the Coefficient= 1.000000;
Coeff. Coeff.
107 0-Command: 107
Low High
1-Reg1: 16960 (Low)
2-Reg2: 15 (High)
Calibration operation. Reg1 and Reg2 values are used used to hold
calibration value. To calibrate 100,000;
Calib. Calib.
108 0-Command:108
Low High
1-Reg1: 34464 (low)
2-Reg2: 1 (high)
System Capacity is set to address 22-23. As a mV/V value, the total
systems loadcells capacity, is set to Reg1 and Reg2 (2 000 000). As an
mV mV
109 Low High
example; 4pcst 10ton capacity with 2.000000mV/V output loadcelss,
40000 values is entered 22-23 registers.
0-Command: 109 1-Reg1: 33920 (Low) 2-Reg2: 30 (High).
122 - - Calibration Zero is done. No need to do other actions
112 - - Lock Keyboard enytry for un-attended access
113 - - Keyboard un-lock operation
123 ShiftL ShiftH Shift Value (Declerated) Screen result is Shifted to ShiftVal
910 - - Calibration Value and Zero is saved to backup area
911 - - Calibration Value and Zero is restored from backup area
FONKSIYON / YUKARI OK
Kalibrasyon menüsünde yük değerini tanımlamak için kullanılır. HABERLEŞME AYARLARI GÜÇ TÜKETIM DEĞERLERI
Sayısal değer girilirken basamak değerini artırmak ve menülerde 1.Port ayarları yapılır
gezerken ileriye gitmek için kullanılır. Haberleşme adresi 01’dir. Besleme 24Vdc, 4 adet Yük Hücresi ile çekilen
Modbus ASC veya RTU seçimi yapılır. Min. Akım: 55mA Min Güç: 1400mW
Max Akım: 104mA Max Güç: 2400mW
MENÜ / MENÜ GIRIŞ / ONAYLA 1200-115200 arası haberleşme hızı seçilir.
Ayar menüsüne giriş için MENÜ tuşu kullanılır. Haberleşme tipi seçilir.
Menü içerisine girmek ve onaylamak için kullanılır. None: Haberleşme yok.
kg: Ekran değeri, seri porttan sürekli iletilir.
Adres: Adresli haberleşme için kullanılır.
Modbus: Modbus haberleşme için kullanılır.
1 2 3 4
MODBUS ADRESLERİ
TR TEKNİK ÖZELLİKLER BOYUTLAR R/W Adr Data
RW 0 Komut
Tanım
Komut Yazmacı