Professional Documents
Culture Documents
2]
id0102f3164700
DTC
Urea tank temperature sensor circuit low
P205C:00
• The SCR control unit monitors input voltage from urea tank temperature sensor while the engine witch is on. If the input voltage is below
0.165 V for 2 sec., the SCR control unit determines that the urea tank temperature sensor circuit voltage is low.
Diagnostic support note
DETECTION • The MIL illuminates if the SCR control unit detects the above malfunction condition in first drive cycle.
CONDITION • The SCR warning light flashes if the SCR control unit detects the above malfunction condition in first drive cycle.
• PENDING CODE is available if the SCR control unit detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA (mode2) and snapshot data are available.
• The DTC is stored in the SCR control unit memory.
• Urea tank temperature sensor short cord connector or terminal malfunction
POSSIBLE • Short to ground in wiring between urea tank temperature sensor terminal J and SCR control unit terminal 56
CAUSE • Urea tank temperature sensor malfunction
• SCR control unit connector or terminal malfunction
• SCR control unit malfunction
Diagnostic procedure
https://euroesi.mazda.co.jp/esicont/eu_eng/cx-7/20090527143252/html/id0102f3164700.html 1/2
1/9/22, 12:25 DTC P205C:00 [MZR-CD 2.2]
STEP • Verify and compare the TANK_TEMP PID values when disconnecting and
INSPECTION ACTION
connecting the urea tank temperature sensor connector.
• Does the TANK_TEMP PID value change? Replace the urea pump, urea tank component then go to Step
No 9.
(See UREA TANK REMOVAL/INSTALLATION [MZR-CD 2.2].)
If the short to ground circuit could be detected:
INSPECT UREA TANK TEMPERATURE SENSOR CIRCUIT FOR SHORT TO • Repair or replace for a possible short to ground.
GROUND If the short to ground circuit could not be detected:
• Urea tank temperature sensor connector is disconnected. Yes • Replace the SCR control unit (short to ground in SCR control
6 • Switch the ignition off. unit internal circuit).
• Inspect for continuity between urea tank temperature sensor short cord (See SCR CONTROL UNIT REMOVAL/INSTALLATION [MZR-
terminal J (SCR control unit-side) and body ground: CD 2.2].)
• Is there continuity? Then go to Step 9.
No Go to the next step.
INSPECT SCR CONTROL UNIT CONNECTOR FOR POOR CONNECTION
• Switch the ignition off. Yes Repair or replace the terminal, then go to Step 9.
7 • Disconnect the SCR control unit connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion). No Go to the next step.
• Is there any malfunction?
INSPECT UREA TANK TEMPERATURE SENSOR SIGNAL AND GROUND
CIRCUITS FOR SHORT TO EACH OTHER Repair or replace the malfunctioning wiring harness, then go to
• Urea tank temperature sensor and SCR control unit connectors are Yes
Step 9.
8 disconnected.
• Inspect for continuity between urea tank temperature sensor short cord
terminals E and J (SCR control unit-side). No Go to the next step.
• Is there continuity?
VERIFY TROUBLESHOOTING OF DTC P205C:00 COMPLETED
Replace the SCR control unit, then go to the next step.
• Make sure to reconnect all disconnected connectors.
Yes (See SCR CONTROL UNIT REMOVAL/INSTALLATION [MZR-
• Clear the DTC from the SCR control unit memory using the M-MDS.
9 CD 2.2].)
• Switch the ignition ON for 2 sec.
• Retrieve the DTC using the M-MDS.
• Is the PENDING CODE for this DTC present? No Go to the next step.
VERIFY AFTER REPAIR PROCEDURE Go to the applicable DTC inspection.
• Perform the “AFTER REPAIR PROCEDURE”. Yes
10 (See DTC TABLE [MZR-CD 2.2].)
(See AFTER REPAIR PROCEDURE [MZR-CD 2.2].)
• Are any DTCs present? No DTC troubleshooting completed.
https://euroesi.mazda.co.jp/esicont/eu_eng/cx-7/20090527143252/html/id0102f3164700.html 2/2