Professional Documents
Culture Documents
Q. No. 3 Design a discrete series regulator for the following conditions. एकदं त 023/मधुर-033
Regulated O/P VL=12V, Maximum load current ILmax=150mA, I/P voltage Vin=20±2V
Draw the designed circuit diagram along with all ratings of components used.
Q. No. 4 Design a part of discrete series regulator circuit to provide Foldback protection to the
regulator for following requirements. चित्ररथ-024
i) VL=6V
ii) IL=1A
iii) Isc=250mA
Draw the designed circuit diagram. Design must include calculation of components and
maximum ratings of transistors.
Q. No. 6 Design a series regulator for output voltage in the range of 10V to 15V at 50mA.
The unregulated power supply voltage of 25±5V and r o=8Ω. Draw the designed
circuit diagram. Design must include calculation of components and calculation
of stability factor and output resistance. Select data I Z=20mA, RZ=17Ω,
hfe1=40/300, hie1=1.3k, hfe2=110, hie2=2.5kΩ. समर्थ-25
Q. No. 9 Design a power supply using 3-terminal regulator IC-340 to provide O/P of 12V
at 0.5A at 350C. Design should include calculation of components values of
unregulated power supply required for this circuit and Heat sink calculation.
महिमा -030
Take Vr(p-p)=1.2V for LM 340-T
θ jA (¿0 C /W )¿ θ jC ( ¿0 C /W )¿ θCS (¿0 C /W ) ¿ Tj C
0
35 2.3 2 150
Q. No. 10 Design a regulated power supply using 3-terminal regulator IC-340 for V o=12V,
IL=0.5A at 350C. Design should include the unregulated power supply section for
required for Vr(p-p)=1.2V . Also find out Heat sink to the IC is required or not.
Take for LM 340-T CEI1330
Drop out voltage θ jA (¿0 C /W ) ¿ θ jC (¿0 C /W )¿ θCS (¿0 C /W )¿ Tj0C
3V 35 2.3 2 150
θ jA (¿ C /W )¿ θ jC ( ¿ C / W )¿ θCS (¿ C /W ) ¿ Tj C
0 0 0 0
35 2.3 2 150
Q. No. 13 Design dual tracking power supply using three terminal IC’s LM-317 and LM-
337 to get [Vo=±5V], [IL=0.5A] for each Vrp-p for filter capacitor is 1.2V at
400C. Draw the designed circuit diagram, Design must include external
components around IC, Heat sink calculation, if required and design unregulated
power supply section. पळस-025
Q. No. 14 Design dual tracking power supply using three terminal IC’s adjustable IC for
following specification. समर्थ-25
VO=±5V to ±20V
IO=1.2A
Draw the designed circuit diagram, Design must include calculation of
components and ratings.
Q. No. 18 Design a step down regulator circuit using LM 1575/2575 IC for V o=12V,
IL=0.5A, Vin=20±2V at 600C. Draw the designed circuit diagram, calculate the
components value connected around IC, Heat sink calculation, if required. [No
need of un-regulated power supply design]. पळस-025
For IC use the data
Vsat(V) Iq(mA) θ jA (¿0 C /W ) ¿ θ jC ( ¿0 C /W )¿ θCS (¿0 C /W ) ¿ Tj0C
0.8 12 65 3 2 150
Q. No. 19 Design a solid state power supply using buck regulator (LM 2575-Adj.) to meet
following specification. समर्थ-25
VLoad=8V regulated
Einminimum=12Vdc
ILoad=800mA
ΔI≤200mA
VLoad ripple≤0.1V
TA ≤600C
Determine all components values including ESR and heat sink if required. No
need of designing unregulated power supply.
Q. No. 20 Design a step down regulator circuit using LM 1575/2575 IC for V o=15V,
IL=800mA, Vin=20±2V and Vr(p-p) for capacitor filter of 2.0V. Draw the
designed circuit diagram, calculate the components value connected around IC,
Heat sink calculation, if required and un-regulated power supply design. मधुर-025
For IC use the data
Vsat Iq(mA) θ jA (¿0 C /W )¿ θ jC ( ¿0 C /W )¿ θCS (¿0 C /W ) ¿ Tj0C Drop out voltage
0.8V 12 65 3 2 150 2V
Q. No. 23 Design a boost type switching regulator using IC 1577/2577 to meet following
parameters. केकावली-30
i) I/P voltage of regulator Ein=5V
ii) O/P voltage of regulator Vo=10V
iii) ILoadmax=0.8A
iv) ΔI=25% of Iindavg
v) ΔVLoad(p-p)=0.05V
vi) θ jA (¿0 C /W )=6 5 ¿
vii) TA=250C
Draw the designed circuit diagram. Design must include calculation of component
values and Heat sink for the IC if required. [No need of un-regulated power
supply design].
Q. No. 24 Design a boost type switching regulator using IC 1577/2577 to meet following
parameters. चारोळी-26
i) I/P voltage of regulator Ein=8V
ii) O/P voltage of regulator Vo=12V
iii) ILoadmax=0.5A
iv) ΔI=25% of Iindavg
v) ΔVLoad(p-p)=0.05V
vi) θ jA (¿0 C /W )=6 5 ¿
0
vii) θ jC (¿ C /W )=2 ¿
viii) TA=270C
ix) Switcher frequency=52khz
Draw the designed circuit diagram. Design must include calculation of component
values and Heat sink for the IC if required. [No need of un-regulated power
supply design].
θ jA (¿ C /W )¿ θ jC ( ¿ C / W )¿ θCS (¿ C /W ) ¿ Tj C
0 0 0 0
35 2.3 2 150
Q. No. 26 Design regulated power supply using LM 217 IC. Which will provide a voltage
adjustable from 1.2V to 20V at currents up to 500mA at 40 0C. Draw the designed
circuit diagram. Design must include selection of transformer, calculation of
ratings of filter capacitor and rectifier diodes and heat sink to IC if required.
जया-028
Drop out voltage θ jA (¿0 C /W ) ¿ θ jC (¿0 C /W )¿
2V 35 2.3
Q. No. 27 Design dual tracking power supply using three terminal IC’s LM-317 and LM-
337 to get [Vo=±5V], [IL=0.5A] for each Vrp-p for filter capacitor is 1.2V at
400C. Draw the designed circuit diagram, Design must include external
components around IC, Heat sink calculation, if required and design unregulated
power supply section. पळस-025