Professional Documents
Culture Documents
My Results
(../studentpanel/page.php? Q.1
page=report&view=overall_report)
A turbine is used to drive a ship, whose rotor has a moment of inertia equal to 20 kg-m2
and is running at 4500 rpm in anticlockwise direction when viewed from front end. The
speed of ship is 108 kmph when it took a right turn around a curve of 600 m radius. The
✉ Message gyroscopic couple (in N-m) experienced by the ship will be _______.
(../studentpanel/page.php?
page=message&view=message_list) Solution
Unseen
Documents
(../studentpanel/page.php? Your Ans
Time (Secs) 0
Solution
Unseen
Your Ans
Correct Ans d
Time (Secs) 0
Bookmark
Q.3
A cam rotating with a uniform angular velocity pushes its flat faced radial follower
upwards. If the nature of the upward displacement of the follower with respect to the
angle of cam rotation is cycloidal, then the shape of acceleration curve is
Solution
Unseen
Your Ans
Correct Ans b
Time (Secs) 0
Bookmark
Q.4
The engine of an aeroplane rotates in clockwise direction when seen from nose end and
the aeroplane takes a turn to left the effect of gyroscop is couple will be
Solution
Unseen
Your Ans
Correct Ans d
Time (Secs) 0
Bookmark
Q.5
none of these
Solution
Unseen
Your Ans
Correct Ans c
Time (Secs) 0
Bookmark
Q.6
In case of partial balancing of single cylinder reciprocating engine, what is the primary
disturbing force along the perpendicular to the line of stroke?
Solution
Unseen
Your Ans
Correct Ans c
Time (Secs) 0
Bookmark
Q.7
A single cylinder reciprocating engine has speed 150 rpm, stroke 350mm, mass of
reciprocating parts 40 kg, mass of revolving parts at 75mm radius is 30 kg. If 60% of the
reciprocating parts and all the revolving parts are to be balanced.
31.718 kg
29.53 kg
63.436 kg
59.06 kg
Solution
Unseen
Your Ans
Correct Ans b
Time (Secs) 0
Bookmark
Q.8
A certain gyroscope consists of a uniform disk with a 50 cm radius mounted at the centre of
an axle that is 11 cm long and of negligible mass. The axle is horizontal and supported at
one end. If the spin rate is 1000 rev/min. The precession rate is ____ rad/s.
Solution
Unseen
Your Ans
Time (Secs) 0
Bookmark
Q.9
A cam rotating clockwise at a uniform speed of 1000 rpm is required to give a roller follower
the following motion:
iii.Follower to return to its starting position during next 90° of cam rotation,
The minimum radius of the cam is 50 mm and the diameter of roller is 10 mm. It’s line of
stroke is off-set by 20 mm from the axis of the cam shaft. If the displacements of the
follower takes place with uniform and equal acceleration and retardation on both the
outwards and return strokes, find the maximum velocity during outstroke in m/sec.
Solution
Unseen
Your Ans
Time (Secs) 0
Bookmark
Q.10
What is the maximum acceleration of a cam follower undergoing simple harmonic motion?
Solution
Unseen
Your Ans
Correct Ans a
Time (Secs) 0
Bookmark
Q.11
Solution
Unseen
Your Ans
Correct Ans d
Time (Secs) 0
Bookmark
Q.12
The length of each connecting rod of a 60ºV engine is 200 mm and the stroke is 100 mm.
The mass of reciprocating parts is 1.5 kg per cylinder and the crank speed is 2100 rpm.
The value of secondary forces (in N) will be __________.
Solution
Unseen
Your Ans
Time (Secs) 0
Bookmark
Q.13