Professional Documents
Culture Documents
Manufacturers/Suppliers:
Company Name DAFER SUPPLY & CONTRACTING ESTABLISHMENT (DASCO)
Local agent NA
Prequalification Approval reference Source Quality Control Reports Certificates & Accreditations
Previous Client Approvals Completed Projects (Similar in Nature) Delegated Design Submittals
Received by Contractor
Signature &
Name
Date
DISCLAIMER: WE CERTIFY THAT ALL THE REQUIREMENTS OF THIS SPECIFICATION FOR THE PROPOSED MATERIALS/PRODUCT/EQUIPMENT HAS BEEN COMPARED, AND THE DEVIATIONS FROM THE SPECIFICATION (IF ANY) HAVE BEEN SPECIFICALLY IDENTIFIED AND ARE DEEMED ACCEPTABLE. PERMISSION TO PROCEED SHALL NOT CONSTITUTE ACCEPTANCE
OR APPROVAL OF MATERIALS SELECTED BY CONTRACTOR AND SHALL NOT RELIEVE CONTRACTOR FROM FULL COMPLIANCE WITH CONTRACT TECHNICAL SPECIFICATIONS, AND APPLICABLE LOCAL AUTHORITIES' SPECIFICATIONS.
Manufacturer / Supplier Name Manufacturer / Supplier Representatives Signatures & Stamps Contractor Name Contractor Representatives Signatures & Stamps
DOCUMENT C ODE : 03-120000 -4800000 441-B OC -CIV-M AT -000026 REVISION C ODE: 0 1 PAGE 1 OF 53
Document history
Document approval
Job Title Procurement Quality Project Manager ( BOC) Contractors Representative- BOC
Control Supervisor (PQCS)
- BOC
DOCUMENT C ODE : 03-120000 -4800000 441-B OC -CIV-M AT -000026 REVISION C ODE: 0 1 PAGE 2 OF 53
Contents
01.Material Checklist…………………………………………………………………………………………04
02.Technical Data Sheet.……………………………………………………………………………………05
03.Material Certificates………………………………………………………………………………………10
Proposed Area of Application / Installation: T-0 Activation, OXAGON Port Contractor: Bin Omairah contracting Co.
Manufacturer / Supplier: DAFER SUPPLY & CONTRACTING ESTABLISHMENT (DASCO) Discipline: CIVIL
03-120000-4800000441-BOC-
Country of Origin: SAUDI ARABIA Materials Submittal No: CIV-MAT-000026
4 Certification / Accreditation. X
PMC Comments:
Reviewed By Accepted By
Name:
Designation
Signature:
Date:
SECTION 321723
PAVEMENT MARKINGS
Page
PART 1 - GENERAL 2
1.1 Related Documents 2
1.2 Summary 2
1.3 Submittals 2
1.4 Quality Assurance 2
1.5 Delivery, Storage And Handling 3
PART 2 - PRODUCTS 3
2.1 Materials 3
2.2 Equipment 6
PART 3 - EXECUTION 6
3.1 General 6
3.2 Application 6
3.3 Protection And Cleaning 8
PART 1 - GENERAL
1.2 SUMMARY
A. This section covers the Roadway Marking Paint works as required by the con-
tract for:
1. Marking of the Center-line, Edge line & Lanes separators, Stop line,
etc.
2. Parking bays
3. Pedestrian Crossings
4. Ground marking shapes (Traffic Arrows, Give way, etc.)
5. Chevrons at merging or diverging of roads
B. Related Sections
1.3 SUBMITTALS
B. Certificate of compliance.
B. AASHTO No.
D. ASTM No.
A. Marking materials and glass beads shall be supplied and delivered to the pro-
ject in manufacturer's original new and unopened containers, factory sealed
and labeled. The containers containing marking materials shall be sealed to
preclude contamination and shall have a capacity of not less than 25 kg nor
more than 100 kg and each container shall be labeled to clearly identify the
following information:
B. Containers of marking materials shall not be opened except for immediate use.
Materials older than the manufacturer's recommended or extended shelf life
shall not be used and shall be removed from the site.
PART 2 - PRODUCTS
2.1 Materials
A. Thermoplastic Paint:
2. The ballotini sprayed on the surface of the line shall conform to the
same limits of color and roundness, Consumption shall be up to 6 kg
per 10 liters of paint.
3. The glass beads must conform to the following requirements:
a. Disintegration Resistance :
b. Roundness :
c. Refraction Index :
1. The liquid and the solid resins must be a result of the condensation of
Bisifinol Epichlorohydrine with properties as shown in the following
table :
a. Titanium Bioxide :
b. Calcium Carbonate :
c. Lead Chromate :
2.2 EQUIPMENT
B. All the lines and shapes done by the markers equipment shall conform to the
(MUTCD)
PART 3 - EXECUTION
3.1 GENERAL
A. Allow paving to cure for 30 days before starting pavement marking paint.
3.2 APPLICATION
A. Weather Limitations: Perform painting only when the existing surface is dry
and clean, when the pavement and air temperatures are above 10oC and
when weather is not too windy, dusty, or foggy for the protection of the satis-
factory painting.
E. Preparation of Surface:
A. All marking paint shall be protected from damage until the paint is dry. Paint
shall be protected from all traffic, vehicle and pedestrian. All paints shall be
maintained to the Ministry Representative's satisfaction.
A high quality White and Yellow Thermoplastic Road Marking Powder conforming to AASHTO M249-
98 Specification. It consist of light coloured aggregates, pigment and extender bound together with a
Thermoplastic Aliphatic Hydrocarbon Resin plasticized with mineral oil and made refractorised using
30-40 pre-mix glass beads complying with AASHTO M247 TYPE-I.
Note: Amount of Yellow pigment calcium carbonate, inert fillers shall be at the option of the
manufacturer, provided all other requirements of the specification are met.
BINDER :
Shall be based predominantly on synthetic hydrocarbon resin, plasticised with mineral oil.
PIGMENTS :
White pigment material shall either consist of Titanium Di-oxide Type A (Anatase) or
Type R (Rutile) and its content shall be such as to give a minimum luminance factor of
75.
For yellow markings the pigment shall be a lead chromate, which is sufficiently colour
stable when heated to 220C.
AGGREGATES :
Light coloured silica sand, calcite, quartz or calcined flint.
PHYSICAL PROPERTIES :
White Yellow
Softening Point : 102 + 9.5ºC 102 + 9.5ºC
Luminance : 75 min 45 min
Specific Gravity : Below 2.15 g/cm³ Below 2.15 g/cm³
Flash Point : Above 235ºC Above 235ºC
Drying Time : 3 – 5 min @ 32ºC 3 – 5 min @ 32ºC
Surface Preparation:
Asphalt surface must be dry, free from dust, grease and loose material. Concrete surface must be dry,
clean, free from laitance and dust, loose material, grease and oil.
Concrete surfaces previously treated with curing compound, must be roughened by slight sand
blasting.
Wc. Saucli Road Marking Co. Ltd. cerlify that Daf'er Supnly and Contracting
I!st.(D;\SCO) o1-P.O. Box 1690. Al I(hobar 31952. Kingdom o1'Saudi Arabia is an
approvccl applicator olour ROMAC'l'hern-roplastic Paints in the Kingdom.
We also certily that Daler Supply and Contracting Est.(l)ASCO) is a regular and uscrs ol
our thermoplastic paints lor many years.
-..
L
r!.-i: ; i
'lLosjtornar
Sautli lload Marking Co. Ltrl. confirms that our ROMAC I-Iotmelt 'I'hermoplastic
Paints are manul'actr-ired and made in l"irst Industrial Arca. Dammam. I(.S.A. Shoulci r.ou
need anl' furlher infbrmation, please do not hesitate to contact us.
TECHNICAL SUBMITTAL
Page 8 of 77
Cold Paint (Standard Paint ) :
a) DASCO will mark the lines evenly and uniformly, and will define
the edges sharply without platting, running or being misty. The curved
( OSAIS AMERON).
c) DASCO will obtain approval for the pre-marked lines from client
Page 24 of 77
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 32 of 53
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 33 of 53
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 34 of 53
Page 26 of 77
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 35 of 53
Page 27 of 77
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 36 of 53
Page 28 of 77
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 37 of 53
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 38 of 53
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 39 of 53
DOCUMENT NO. 03-120000-4800000441-BOC-CIV-MAT-000026 REVISION CODE: 01 Page 40 of 53
Photos:
Sadara –Jubail
Final (WF-020837) 1100001341-034 - Material Submittal for Road Marking & Cat Eyes Aluminum
(DASCO).
To
(4) Mr Albin Salipdan - SAUDI ARABIAN PARSONS LIMITED (+3 more...)
Cc
(6) NEOM Quality & Excellence Document Control - NEOM - Engineering & Technical Services Dept (+5 more...)
Status N/A
DOCUMENT ATTACHMENTS
(1)
(0 selected)
Revision
File Document No Revision Title Status
Date
03-140000-1100001341-NAP-CIV- 1100001341-034 - Material Submittal for Road Marking & Cat Eyes A - Work May
02 26/06/2022
MAT-000082 Aluminum (DASCO). Proceed
MESSAGE
The attached documents have completed the "1100001341-034 - Material Submittal for Road Marking & Cat Eyes Aluminum (DASCO)." workflow with the following results :