Professional Documents
Culture Documents
REFERENES-TEXT BOOKS
1) Ö. KALENDERLİ, C. KOCATEPE, O. ARIKAN, Çözümlü Problemlerle
Yüksek Gerilim Tekniği, Cilt 1, Birsen Yayınevi, 2005
2) M. ÖZKAYA , Yüksek Gerilim Tekniği CİLT 1 , Statik Elektrik Alanı
Ve Boşalma Olayları , 1988 , İTÜ
3) M.ÖZKAYA , Yüksek Gerilim Tekniği CİLT 2 , 1988 , İTÜ
4) İ. GÖNENÇ , Yüksek Gerilim Tekniği CİLT 1 , 1977 , İTÜ
5) M. ÖZKAYA , Yüksek Gerilim Tekniğinde Deşarj Olayları , 1979 , İTÜ
6) M. ÖZKAYA , Yüksek Gerilim Tekniğinde Ölçme , 1984 , İTÜ
7) E. KUFFEL , M. ABDULLAH , (Çevirenler : M. ÖZKAYA , T. TÜFEKÇİ ,
N. ERGAN) , Yüksek Gerilim Tekniği , 1988, İTÜ )
Basic stages from power generation to consumer points are illustrated in the following figure:
CHAPTER 1 --- Fundamental Principals of High Voltage Tech.
Transmission line can be single circuit or double circuit:
Note: Cables used in AC can also b used in DC. Un-presence of capacitive current in DC,
makes power transmission easier in cables.
Types of power cables:
» Paper insulated
» Oil filled
» Pressured Gas
» Plastic insulated
CHAPTER 1 --- Fundamental Principals of High Voltage Tech.
• While power is generally transmitted over three- phase ac transmission
line, there are circumstances in which HVDC lines have certain benefits.
According to AC transmission, HVDC lines became economical after 500-
600 km in over- head lines, and 50 km in cabled transmission.
1.1. Reasons of using high voltage
Pheses and voltages in three phase system can be given as below :
(No neutral line in transmission. İt is found in distribution system. )
ΔP = 3.R.Ι 2
Relative Power Loss:
P
3.R
ΔP 3.R.Ι 2
3.R.Ι 3.U . cos ϕ 3.R.P
p= = = = =
P 3.U .Ι. cos ϕ 3.U . cos ϕ 3.U . cos ϕ 3 .
U 2
cos 2
ϕ
R
p = P.
U 2 . cos 2 ϕ
• cos φ ↑
cos φ can be increased within a limited range ( 0<cos φ<1 ).
Since increasing cos φ requires compensation system, it adds
extra cost. So it has limited benefits.
• U↑
Best suitable way is to increase voltage, U.
With the increasing voltage ( copper losses = I2. R losses ) decreases.
1.1. Reasons of using high voltage -Continue
• Can voltage be increases as much as desired ?
–In this case, following problems occur
• Discharge events and insulation problems
• Protection of lines against over voltages
• Difficulties in High voltage generation and measurement
Transmission voltage level is determined versus power and distance for economic transmission.
Following figures gives the economic transmission voltage level versus power and distance for double circuit system:
Long transmission line parameters are assumed to be evenly distributed over the line
range. So, equivalent circuit of the long transmission line can be given as in Fig. 1.
R′ L′ R′ L′
ℓ = Line length.
R= Rı . ℓ
C′ G′ C′ G′ C′ G′ L = Lı . ℓ
G= Gı . ℓ
C= Cı . ℓ
1.3. NATURAL POWER - Continue
• Assuming the line lossless : Rı = 0 , Gı = 0 . In this case:
• Z= j.ω.Lı.ℓ and Y= j.ω.C’.ℓ. Therefore, surge
impedance, zo
L' L
ZO = '
= (Surge Impedance)
C C
1
v= (Wave Propagation Speed)
L′ ⋅ C′
This speed in the cabled line is dependent upon the di- electric constant of
the insulating material, and is approximately equal to half of the light
speed.
L' 1 L' 1
= 2 2 = ZO =
C ' v .C ' C' v.C '
U 2 3 ⋅ U 2F
SIL = =
ZC ZC
•where U is phase to phase voltage and, UF is phase to neutral voltage.
•Natural power is defined for a radial line (one generator- single load point). That is why it was
frequently used in the past. For interconnected system, it can be used for a specific line loading, which
means that natural power is the criteria for determining the maximum loading level of a line.
1.3. Natural Power - Continue
• Transmission lines are not loaded generally with natural power.
• If natural power > power to be transmitted ==> voltage increases.
(in this case additional inductance needed)
R
U RO= ZO RO
S
RO
U
T
1.4. The Classification of H.V. and Definitions
As well as usage of H.V. in power system and industry, it is required used to test
devices and their insulation level.
High Voltage can be divided into three parts in terms of its variation versus time
(1) High DC voltage; (2) High AC voltage; (3) Impulse voltage
U max − U min
Fluctuating Magnitude =
2
U max − U min
Fluctuating Factor =
2.U avg
1.4. The Classification of H.V. and Definitions - Continue
According to IEC (International Electrotechnical Commission) , FF
should be less than %5 when testing the devices using DC voltage
(FF < %5 ).
Where do we use High DC voltage: Capacitor and cable testing; Electro-
static filter; paint spraying system
High AC voltage : If polarity and the magnitude of voltage vary periodically, it
is called alternating voltage. It is used for testing purposes as well as
generating High DC and impulse voltage. Generators can supply 10-20 kV or
up to 35 kV voltages.
In the low voltage level, generally sinusoidal alternating voltages used. In practice
they contain HARMONIC COMPENENTS.
An Alternating Current can be
characterized by
- Frequency; peak value, effective
value (rms value) and voltage
waveform (sinusoidal, triangular,
rectangular)
1 T 1 T U 2m T 1 − cos 2ωt
U= ∫0 U (t ).dωt = T ∫0 U m . sin ωt.dωt = T ∫ .dωt
2 2 2
T 0 2
Frequency in Europe and TURKEY is 50 Hz. However for testing purposes, the
frequency range [40-62] Hz can be used as an 50 Hz value.
As for the magnitude of the test voltage including harmonic components;
Tc = 1,67 x T
Tı = 0,3 x Tc = 0,5 x T
1.4. YÜKSEK GERİLİM ÇEŞİTLERİ VE TANIMLARI-Devam
Anma Cephesi Süresi (TC) : Anma gerilimi tepe değerinin %30 - %90’ının
meydana geldiği anlar arasındaki sürenin (T) 1,67 katıdır.
Anma Sırt Yarı Değer Süresi (TS) : Anma başlangıç noktası (Oı) ile gerilimin
sırtta tepe değerin yarısına düştüğü ana karşı düşen noktalar arasındaki süredir.
Tepe Değeri (UMAX) : Gerilimin maksimum değeridir.
Darbe gerilimleri Tc/Ts olarak verilir. En çok kullanılan standart darbe gerilimi
1,2/50 µs (Cephe Süresi / Sırt yarı değer süresi)’dir. U
TC = 1,2 ± %30 tolerans kabul edilir. Cephede Kesilmiş
TS = 50 ± %20 tolerans kabul edilir.
UMAX = UMAX ± %3 tolerans kabul edilir.
G G
U1
U1
~ ~
Tam İzole Hali Tam İzole Hali
1.4. YÜKSEK GERİLİMLERİN ÜRETİLMESİ- Devam
b) Çok Katlı Deney Transformatörleri: Birkaç yüz kV ‘ un üstünde gerilimler için bir
katlı deney transformatörü değil de yüksek gerilim sargıları seri bağlı birkaç
deney transformatörü yardımıyla elde edilir. Örneğin 1,2 MV‘luk gerilim için 3
adet 400 kV ‘luk üniteler halinde elde edilir.
Tek katlı transformatör ekonomik olmadığından bu yol kullanılır.
Bir transformatörün ağırlığı (hacmi) kübü ile doğru orantılıdır: G= k .U3
kullanılan küresel
elektrotların kapasitelerini gösterir
C2
F = Küresel elektrodlar F L
1
L
2
Tesla Transformatörü
Buna tesla transformatörü de denir.C1 kondansatörü U1 gerilimi ile dolar. F’ler yaklaştırılır ve atlama
olunca rezonans ile U2 gerilimi oluşur. Gerilim düşünce atlama durur. U1 gerilimi sürekli uygulanınca
atlama sürekli meydana geldikçe U2 gerilimi elde edilir. F’lerin açıklığı U2 gerilimini L1 ve C1 ise f ’i
belirler. F küresel elktodlarının faliyete geçmesi ile seri rezonans devresi meydana gelir.Yüksek
frekanslı sönümlü titreşimler oluşur. Bu frekans : X1 = XC1
1 1
2.π . f .L1 = => f =
2.π . f .C1 2.π . L1 .C1
1.4. YÜKSEK GERİLİMLERİN ÜRETİLMESİ- Devam
1.5.2 Yüksek Doğru Gerilimlerin Üretilmesi:
Yüksek doğru gerilim, laboratuarlarda kondansatör , kablo gibi kapasitesi büyük olan yalıtkan
malzemelerin muayenesinde ve fiziksel incemeler için kullanılır.
• Tıbbi elektronik (röntgen)
• Püskürtme (elektrostatik toz) boya
• Baca gazı filtresinde kullanılır.
i
1.4. YÜKSEK GERİLİMLERİN ÜRETİLMESİ- Devam
a)Yarım Dalga Doğrultucu Devresi :
Bağlantı şeması
⎛ −t ⎞ −t
U = E ⎜1 − e T ⎟
i = Ι.e T
HATIRLATMA : ⎜ ⎟
⎝ ⎠
1.4. YÜKSEK GERİLİMLERİN ÜRETİLMESİ- Devam
b) Greinacher Devresi: Villard devresinin genişletilmiş şekli olup , yarım dalga tek
kademeli gerilim katlayıcı devredir.
U(t)
U (t)
2. Um
Um
wt
D2 diyotu ve C2 kondansatörü ile sabit doğru gerilim elde edilir . D2 diyotu dalgalanmayı
azaltır. D2 diyotu kullanılmadığı zaman UC2=2Um gerilimi ters yönde akım akıtarak
dalga şeklini bozar. Çıkışta 2Um’ lik gerilim elde edildiği için C2 kondansatörü 2Um’lik
gerilime, C1 ve D elemanları Um' e göre seçilmek zorundadır.
1.4. YÜKSEK GERİLİMLERİN ÜRETİLMESİ- Devam
c) Zimmermann-Wittka Devresi: iki Villard devresi karşılıklı yerleştirilirse, çıkış
uçlarında tepe değeri transformatörün tepe gerilimin 3 katı olan dalgalı bir doğru
gerilim elde edilir.
C
- +
U
- -
U(t)
3Um
~
2Um
C
- + + +
t
U(t)
Kondansatörler Um + Um = 2.Um ile dolar. Bunun üzerine Um .sinωt ile süperpoze edilir.
380000 2 Z0
P0 = = 288,94.10 6 W = 288,94 MW L3
499,75
N
U 3 P0
I= or I =
Z0 3 ⋅U ⋅ cos ϕ
380 ⋅ 10 3 3
I= = 439 A
499,75
PROBLEM SOLUTION - 1
R=
l Z0 = 499,75 Ω
k ⋅S
l 500 ⋅ 10 3
ΔP = 3 ⋅ ⋅ I = 3⋅
2
⋅ 439 2
k ⋅S 31,56 ⋅ 547,34
= 16,73 ⋅ 10 6 W
PROBLEM 1.2 PROBLEM SOLUTION - 1
For a three-phase transmission line, calculate SOLUTION 1.2
the following: a) Surge impedance:
(a) Surge impedance=?
(b) Wave propagtion speed =? L′ 1,26 ⋅ 10 −3
Z0 = = = 374,2 Ω
(c) Travel time of the wave between “sending- C′ 9 ⋅ 10 −9
l 400
t= = = 1,33 ⋅ 10 -3
s = 1,33 ms
v 3 ⋅ 10 5
PROBLEM SOLUTION - 1
PROBLEM 1.3
b) We need to know thİletim hattındaki kayıp
A new transmission system will be designed for a
gücü bulmak için önce hattın ohmik direnci
power of 100 MVA with power factor cos ϕ =
bulunmalı line resistance in order to find power
0,85. If current carrying capacity (ampacity) of the
line is 400 A , line lenght, l = 300 km with k = 35 loss through the lines.
m/Ωmm2 and current density j = 0,5 A/mm2, l We don’t know the cross-
find the following
R=
k ⋅S sectional area. So
(a) Transmission voltage level =?
(b) Line power loss in the transmission system =? I 400
(c) Find the power loss for standard voltage. I = j⋅S ⇒ S = = = 800 mm2
j 0,5
(d) If one-level higher standard voltage is used
find the percent reduction in power loss.
l 300 ⋅ 103
SOLUTION1.3 R= = = 10,71 Ω
k ⋅ S 35 ⋅ 800
a) As we know, power transmission is performed
by three phase system. Copmlex power, Total power loss,
müsaade edilir. Bir çok halde % 2,5 ile % 5 arasındaki ölçme hataları kabul edilebilir değerlerdir.
where Hk = ± % .
Error classes of the measurement circuits: 0,1% - 0,2% - 0,5% - 1% - 1,5% - 2,5%.
For examle if the class is 0.5 then Hk = ± % 0,5.
1.6. HIGH VOLTAGE MEASUREMENT CIRCUITS - Continue
High voltage measurement circuits can be divided into two groups:
A) Measurement circuits that use HV measurement device
B) Measurement circuits that use LV measurement device
1000 D= 100 cm
D= 50 cm
D= 25 cm
10 cm
200
a
10 50 ( cm )
Gap spacing
Breakdown voltage of sphere gap as function of gap spacing a, for different arrangement and various
diameters D.
Weather conditions have an effect on the breakdown voltages of sphere gaps. Breakdown voltages
are given for standard conditions in the VDE and IEC norms.
Except for the standard conditions, the factor
i.e.. relative air density δ is used. ⎧ U = δ ⋅U n for 0.95 ≤ δ ≤ 1.05
⎨
Breakdown voltages of sphere gaps as a ⎩U = k (δ ) ⋅ U n for 0.95 > δ , δ > 1.05
function of relative air density δ :
1.6.1 MEASUREMENT WITH SPHERICAL ELECTRODES : - Continue
Un = Breakdown voltage under normal conditions (20 0C ,760 mm Hg, or 20 0C ,1013
mbar)
k(δ)= correction factor as a function of relative air density δ
U = Breakdown voltage under different weather conditions
ρ 273 + 20 ρ
δ= ⋅ = 0,386 ⋅ where: [ ρ (mm Hg) ,θ ( 0C ) ]
760 273 + θ 273 + θ
or
b 273 + 20 b
δ= . = 0,289 . where: [ b (mbar) ,θ ( 0C ) ]
1013 273 + θ 273 + θ
Sphere Arrangements :
¾For symmetric arrangement, voltage
is applied to both sphere together.
U U
0 Ud
16
U d 50 U d
84 k
Application - 2
PROBLEM 2.1
The breakdown voltage values in the below table is obtained from a sphere
gap based measurement of high alternating voltage. The test is performed
under standard conditions with the 25cm diameter spheres.
Table:
Gap spacing, a (cm) 5,0 6,0 7,0 8,0 9,0 10,0
Breakdown voltage, U
137 161 180 206 226 244
(kVtepe)
(a) Find the gap spacing for 190 kV breakdown voltage under NWC (normal
weather condition).a190kV=?.
(b) Find the U8,5 cm for the weather conditions of 12 oC and 754 mmHg pressure.
(c) Find the sphere gap for the 170 kV under the weather conditions of (b).
(d) Find the sphere gap for the 170 kV under the NWC