Professional Documents
Culture Documents
1.5 Deleterious Content Test IS:2720 Part 27 As required < 0.50 % MORTH Clause 305.2.1.3
1.6 Moisture Content Test IS:2720 Part 2 2 Test per 3000 m3 +1% & -2% of OMC MORTH Clause 305.3.5.2
1.7 CBR IS:2720 Part 16 1 Test per 3000 m3 As per Pavement Design MORTH Clause 305.2.1.6
Compaction > 95 %
1.8 Density of Compacted Layer (By Sand Replacement Method) IS:2720 Part 28 1set of 10 tests per 3000 m2 Compaction for remaining portion of emb. MORTH Table 300-2
90 - 95 %
2 SUB-GRADE / SHOULDER
2.1 Free Swelling Index IS:2720 Part 40 As required < 50 % MORTH Clause 305.2.1.2
2.2 Grain Size Analysis IS:2720 Part 4 2 Test per 3000 m3 Not Specified MORTH Clause 305.2.1.4
2.3 Density Test (Modified Proctor Test) IS:2720 Part 8 2 Test per 3000 m3 >17.5 KN/m3 MORTH Table 300-1
2.5 Deleterious Content Test IS:2720 Part 27 As required < 0.50 % MORTH Clause 305.2.1.3
2.6 Moisture Content Test IS:2720 Part 2 2 Test per 3000 m3 +1% & -2% of OMC MORTH Clause 305.3.5.2
2.7 CBR IS:2720 Part 16 1 Test per 3000 m3 As per Pavement Design MORTH Clause 305.2.1.6
2.8 Density of Compacted Layer (By Sand Replacement Method) IS:2720 Part 28 1set of 10 tests per 2000 m2 > 97 % MORTH Table 300-2
3 GRANULAR SUB-BASE (GSB)
3.1 Sieve Analysis IS:2386 Part 1 1 Test per 400 m3 Grading - V MORTH Table 401
3.2 Atterbergs Limit IS:2720 Part 5 1 Test per 400 m3 LL < 25 % & PI < 6 % MORTH Table 402
3.3 Density Test (Modified Proctor Test) IS:2720 Part 8 As Required Not Specified -
3.4 CBR IS:2720 Part 16 As Required > 30 % MORTH Table 400-2
3.5 Deleterious Constituents IS:2720 Part 27 As Required Not Specified MORTH Table 900-3
Water Absorption < 2 %
If Water Absorption of Aggregate is greater than 2
3.6 Water Absorption IS:2386 Part 3 As Required MORTH Clause 401.2.2
% then the Aggregates shall be tested for Wet AIV
(IS:5640)
3.7 Aggregate Impact Value IS:2386 Part 4 As Required < 40 % MORTH Table 400-2
3.8 Wet Aggregate Impact Value IS:5640 As Required < 40 % MORTH Table 400-2
3.9 Water permeability Test IRC:37-2018 As Required As per Pavement Design IRC:37-2018
3.90 Moisture content prior to compaction IS:2720 Part 2 1 Test per 400 m3 below 1% & 2% of OMC MORTH Clause 401.3.2
3.10 Density of Compacted Layer (By Sand Replacement Method) IS:2720 Part 28 1set of 3 tests per 1000 m2 > 98 % MORTH Clause 401.3.2
4 CEMENT TREATED SUB-BASE/BASE
As per IRC:37-2018 & MORTH
4.1 Sieve Analysis IS:2386 Part 1 Ones per day's work Depend of Grading Type
Table 401 & 404
4.2 Atterbergs Limit IS:2720 Part 5 Ones per day's work LL < 45 % & PI < 20 % MORTH Clause 403.2.1
4.3 Density Test (Modified Proctor Test) IS:2720 Part 8 As Required Not Specified MORTH Clause 403.2.6
4.4 UCS (CTSB) IRC:SP:89-2010 1.5-3.0 Mpa Clause 7.3.2 IRC:37-2018
4.5 UCS (CTB) IRC:SP:89-2010 1 test 3 specimend per 400 MT or 4.5-7.0 Mpa Clause 8.2.1 IRC:37-2018
Flexural Strength Min. 2 test in a day Clause 14 IRC:37-2018
Cement Content Clause 14 IRC:37-2018
4.6 Deleterious Constituents IS:2720 Part 27 As required Not Specified MORTH Table 900-3
4.7 Soundness IS:2720 Part 5 1 test per source Clause 14 IRC:37-2018
4.8 Moisture content prior to compaction IS:2720 Part 2 1 set of 2 tests per 500 m 2
above upto 2% of OMC MORTH Clause 403.3.4
4.9 Density of Compacted Layer (By Sand Replacement Method) IS:2720 Part 28 1 set of 2 tests per 500 m2 > 98 % MORTH Clause 403.3.5
5 WET MIX MACADAM (WMM)
5.1 Sieve Analysis IS:2386 Part 1 1 Test per 200 m 3
MORTH Table 400-13 MORTH Table 400-13
5.2 Flakiness & Elongation Indices IS:2386 Part 1 1 Test per 500 m3 < 35 % MORTH Table 400-12
5.3 Aggregate Impact Value IS:2386 Part 4 1 Test per 1000 m3 < 30 % MORTH Table 400-12
LAAV < 40 %, (Optional test of AIV)
5.4 Los Angeles Abrasion Test IS:2386 Part 4 As Required MORTH Table 400-12
5.5 Atterbergs Limit IS:2720 Part 5 1 Test per 200 m3 PI < 6 % MORTH Clause 406.2.1.2
5.6 Density Test (Modified Proctor Test) IS:2720 Part 8 As Required Not Specified -
5.7 Moisture content prior to compaction IS:2720 Part 2 1 Test per 400 m3 below 1% & above 1% of OMC IRC:109
5.8 Water Absorption IS:2386 Part 3 1 Test per Source Water Absorption < 2 % MORTH Clause 406.2.1.1
If water absorption coarse aggregate greater
than 2%:- MORTH Clause 406.2.1.1 &
5.9 Soundness of aggregates IS:2386 Part 5 1 Test per Source
(i) Sodium Sulphate < 12% IS:383
(ii) Magnesium Sulphate < 18%
5.10 Density of Compacted Layer (By Sand Replacement Method) IS:2720 Part 28 3 Test per 1000 m2 > 98 % MORTH Clause 406.3.5
6 DENSE BITUMINOUS MACADAM (DBM)/ BITUMINOUS CONCRETE (BC)
6.1 Aggregate Impact Value IS:2386 Part 4 1 Test per 350 m3 DBM < 27%, BC < 24% MORTH Table 500-8 & 500-16
6.3 Flakiness & Elongation Indices IS:2386 Part 1 1 Test per 350 m3 < 35% MORTH Table 500-8 & 500-16
6.5 Water Absorption IS:2386 Part 3 1 Test per Source < 2% MORTH Table 500-8 & 500-16
6.6 Sand Equivalent Test IS:2720 Part 37 1 Test per Source > 50% MORTH Clause 505.2.3
6.7 Plasticity Index IS:2720 Part 5 1 Test per Source > 4% MORTH Clause 505.2.3
6.8 Stripping Value of Aggregates IS:6241 1 Test per Source > 95% MORTH Table 500-8 & 500-16
6.10 Water Sensitivity of mix (Retained Tensile Strength) AASHTO:T 283 1 Test per Source > 80% MORTH Table 500-8 & 500-16
6.11 Polished Stone Value BS:812 Part 114 1 Test per Source > 55% MORTH Table 500-16
1 Set per 400 MT or Min. 2 test per
6.12 Sieve Analysis (Individual) IS:2386 Part 1 Not Specified MORTH Table 500-10 & 500-17
day per plant
1 Set per 400 MT or Min. 2 test per
6.13 Sieve Analysis (Combined) IS:2386 Part 1 Depend on Grading Type MORTH Table 500-10 & 500-17
day per plant
6.23 Density of Compacted Layer by Core Cutting ASTM:D 2726 1 Test per 700 m2 > 92% of Maximum Specific Gravity (Gmm) MORTH Clause 505.3.5
7 MASTIC ASPHALT
MORTH Table 500-39,
7.1 Quality of Binder IS:1201-1220 1 Test per 350 m3 -
IRC 107-2013
7.2 Aggregate Impact Value IS:2386 Part 4 1 Test per 350 m3 30% MORTH Clause 516.2.2
7.3 Los Angeles Abrasion Test IS:2386 Part 4 1 Test per Source LAAV < 40 % Optional test of AIV MORTH Clause 516.2.2
7.4 Flakiness & Elongation Indices IS:2386 Part 1 1 Test per 350 m3 < 35% MORTH Clause 516.2.2
(i) Sodium Sulphate < 12%
7.5 Soundness of aggregates IS:2386 Part 5 1 Test per Source MORTH Clause 516.2.2
(ii) Magnesium Sulphate < 18%
7.6 Water Absorption IS:2386 Part 3 1 Test per Source < 2% MORTH Clause 516.2.2
7.7 Stripping Value of Aggregates IS:6241 1 Test per Source > 95% MORTH Clause 516.2.2
7.8 Water Sensitivity of mix (Retained Tensile Strength) AASHTO:T 283 1 Test per Source > 80% MORTH Clause 516.2.2
8.15 Core Strength of (PQC) IS:516 Part 1 (Sec-1) As required > 85 % of the characteristics strength MORTH Clause 602.11.5.4
1 to 5 m3 - 1 sample
6 to15 m3 - 2 samples
16 to 30 m3 - 3 samples
9.2 Compressive Strength of Concrete for Each grade IS:516 Part 1 (Sec-1) Minimum Characteristic Strength MORTH Table 1700-9
31 to 50 m3- 4 samples
3
51m and above - 4 +1 additional
sample per additional 50m3
9.3 Sieve Analysis (Coarse Aggregate) IS:2386 Part 1 1 Test per Day Depend on Grading Type MORTH Table 1001 & IS:383
9.4 Sieve Analysis (Fine Aggregate) IS:2386 Part 1 1 Test per Day Depend on Grading Type MORTH Table 1002
9.5 Flakiness & Elongation IS:2386 Part 1 2 Test per Week < 40% MORTH Clause 1007 & IS:383
9.6 Aggregate Impact Value IS:2386 Part 4 2 Test per Week < 45% MORTH Clause 1007 & IS:383
9.7 Moisture Content Test ASTM:C566 1 Test per Day - MORTH Clause 1007 & IS:383
9.8 Deleterious Constituents IS:2386 Part 2 1 Test per Source As per IS:383 MORTH Clause 1007 & IS:383
9.9 Specify Gravity & Water absorption IS:2386 Part 3 1 Test per Source Not Specified MORTH Clause 1007 & IS:383
9.12 Alkali Aggregate Reactivity (CA & FA) IS:2386 Part 7 1 Test per Source Innocuous Aggregate MORTH Clause 1007 & IS:383
9.13 Petrographic Examination IS:2386 Part 8 1 Test per Source - MORTH Clause 1007 & IS:383
10.5-a Residue by Evaporation IS:8887 1 Test per Source As per type of Emulsion IS:8887 Table 1
10.5-b Penetration test @ 25⁰ C IS:1203 1 Test per Source As per type of Emulsion IS:8887 Table 1
Sr. No Test Test Reference Test Frequency Acceptance Criteria Specification Reference
10.5-c Ductility @ 27⁰ C IS:1208 1 Test per Source As per type of Emulsion IS:8887 Table 1
10.5-d Solubility in Trychloroethelene IS:1216 1 Test per Source As per type of Emulsion IS:8887 Table 1
10.6 Distillation Test IS:1213 1 Test per Source As per type of Emulsion IS:8887 Table 1
10.7 Rate of spread of Binder (Prime Coat) IRC:SP 11 3 Test per day 0.7 to 1.0 kg/m2 MORTH Table 500-3
14.7 Suspended matter IS:3025 Part 17 1 Test per Source 2000 mg/lit MORTH Clause 1010
14.8 pH Value MORTH Clause 1010 1 Test per Source Minimum 6 MORTH Clause 1010
15 REINFORCED STEEL (TMT)
15.1 Carbon (C) IS:228-1 As required Depend on Steel grade IS:432 / IS:1786
15.2 Sulphur (S) IS:228-9 As required Depend on Steel grade IS:432 / IS:1786
15.3 Phosphorus (P) IS:228-3 As required Depend on Steel grade IS:432 / IS:1786
15.4 Sulphur and phosphorus (S+P) IS:228 As required Depend on Steel grade IS:432 / IS:1786
15.5 0.2 percent proof stress/ yield stress IS:1608 As required Depend on Steel grade IS:432 / IS:1786
15.6 Elongation IS:1608 As required Depend on Steel grade IS:432 / IS:1786
15.7 Tensile Strength IS:1608 As required Depend on Steel grade IS:432 / IS:1786
15.8 TS/YS ratio IS:1608 As required Depend on Steel grade IS:432 / IS:1786
15.9 Bend Test IS:1599 As required Depend on Steel grade IS:432 / IS:1786
15.10 Re - Bend Test IS:1786 As required Depend on Steel grade IS:432 / IS:1786
16 RCC HUME PIPE
16.1-a Tolerances in Dimensions
16.1-b Over all length IS:458 As per Lot Size + 1 % of Standard Length Clause 8.2 IS:458
16.1-c Wall Thickness IS:458 As per Lot Size Depend upon Dia. Of Pipes Clause 8.2 IS:458
16.1-d Internal dia of Pipe IS:458 As per Lot Size Depend upon Dia. Of Pipes Clause 8.2 IS:458
16.2 Reinforcement IS:458 As per Lot Size Depend upon Dia. Of Pipes Tabble 6 IS:458
16.3 Three Edge Bearing Test IS:3597 As per Lot Size Depend upon Dia. Of Pipes Tabble 6 IS:458
16.4 Hydrostatic Test IS:3597 As per Lot Size Depend upon Dia. Of Pipes IS:458
16.5 Permeability Test IS:3597 As per Lot Size + 1 % of Standard Length IS:458
17 FLYASH (MINERAL ADMIXTURE)
17.1 SiO2 + Al2O3 + Fe2O3 IS:1727 As required 70 Min. IS:3812 Part 1
17.2 Silica dioxide (SiO2 ) IS:1727 As required 35 Min. IS:3812 Part 1
17.3 Reactive Silica IS:3813 Part 1 As required 20 Min. IS:3812 Part 1
17.4 MgO IS:1727 As required 5.0 Min. IS:3812 Part 1
17.5 Total Sulphur as SO3 IS:1727 As required 3.0 Min. IS:3812 Part 1
17.6 Available alkalis as Na2O IS:4032 As required 1.5 Min. IS:3812 Part 1
17.7 Total Chlorides IS:12423 As required 0.05 Max. IS:3812 Part 1
17.8 Loss on ignition IS:1727 As required 5 Max. IS:3812 Part 1
17.9 Fineness-Specific Surface Area IS:4031 Part 2 320. Max. IS:3812 Part 1
17.10 Particles Retained on 45 micron Sieve (wet sieving) IS:4031 Part 1 As required 34 Max. IS:3812 Part 1
17.11 Lime Reactivity IS:1727 As required 4.5 Min. IS:3812 Part 1
17.12 Compressive Strength at 28 Days IS:4031 Part 6 2 Test per 700 m2 80% Min. IS:3812 Part 1
17.13 Soundness by autoclave test Expansion of specimen IS:4031 Part 3 As required 0.8 Max. IS:3812 Part 1