Professional Documents
Culture Documents
Shutdown SIS
Previous Screen
Product: GAS ENGINE
Model: G3406 GAS ENGINE 4FD
Configuration: G3406 Industrial Engine Natural Gas 4FD00001-UP
2. Remove four bolts (1) from the aftercooler water line (2).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 2 of 13
3. Remove four nuts and washers (3) and remove the water pump (4) and its gasket.
4. Disconnect the aftercooler water line (2) and remove the gasket.
NOTE: The following steps are for the installation of the auxiliary water pump.
5. Put the auxiliary water pump (4) in position with four nuts and washers (3).
7. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.
Start By:
1. Remove screws (1) and cover assembly (2) from body assembly (3).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 3 of 13
2. Remove plate (5) and gasket (4) from the cover assembly.
3. Remove seal (6) and impeller assembly (7) from the body assembly.
NOTE: Make a note of the direction of the impeller blades for correct assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 4 of 13
5. Use tool (A) and remove ring (10) from the shaft.
6. Remove cover (9) [part of the seal assembly] from the body assembly.
7. Remove spring (11) [part of the seal assembly] from the body assembly.
8. Remove carbon seal (12) [part of the seal assembly] from the body assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 5 of 13
9. Remove bolts (14) and remove housing (13) from the body assembly (3).
10. Remove cam (15) and ceramic seal (16) [part of the seal assembly] from the body assembly (3).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 6 of 13
13. Use tool (B) and remove ring (19) from the housing.
14. Use a press and remove shaft (20) and the bearings from the housing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 7 of 13
15. Use a press and tool (C) to remove bearings (21) from the shaft (20).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 8 of 13
1. Use tool group (A) and install seal (1) in housing (2). Make sure the lip of the seal is toward the bearing bore as shown. Put 1P808
General Purpose Lubricant on the lip of the seal.
2. Use a press and tool (B) to install bearings (4) on shaft (3).
3. Put 1P808 General Purpose Lubricant on the bearings and in the bearing bore of housing (2).
4. Use a press and install shaft (3) and the bearings in housing (2).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 9 of 13
6. Inspect seal (6) for wear or damage and make a replacement if necessary.
7. Put clean engine oil on seal (6) and install the seal on the shaft as shown.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 10 of 13
9. Make an alignment of the dowel (10) in body assembly (7) with cam (9). Install cam (9) in body assembly.
10. Install housing (2) on body assembly (7) and install the bolts that hold the two together.
NOTE: Parts (11), (12), (13) and (14) come as a seal assembly only.
11. Put clean engine oil on the rubber part only of ceramic seal (11).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 11 of 13
12. Put clean engine oil in the seal bore of the body assembly and install ceramic seal (11), polished surface toward the impeller. If the face
of the seal is damaged (marked or scratched) a replacement must be made.
13. Install seal (12) in the body assembly with the polished carbon seal face of the seal toward the ceramic seal.
14. Install spring (13) and cover (14) in the body assembly.
15. Use tool (D) and install ring (15) on the shaft that holds the seal assembly in place.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 12 of 13
16. Inspect seal (16) for wear or damaged and make a replacement if necessary.
17. Put clean engine oil on seal (16) and install on the shaft.
18. Put a small amount of 1P808 General Purpose Lubricant in the impeller bore.
19. Make sure all impeller blades are bent in the same direction and in the correct direction of rotation.
20. Use tool (E) and install impeller assembly (17) in the body assembly.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023
G3406 Industrial Engine Natural Gas 4FD00001-UP(SEBP1772 - 94)/Basic Search Page 13 of 13
22. Install gasket (19) and plate (21) on cover assembly (20).
23. Make an alignment of the dowel in cover assembly (20) and the dowel hole in the cam and install cover assembly (20) with the screws
that hold it.
End By:
Copyright 1993 - 2023 Caterpillar Inc. Sun Feb 19 17:31:59 UTC+0100 2023
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp... 2/19/2023