Professional Documents
Culture Documents
Page 1 of 8
Shutdown SIS
Previous Screen
Water Pump
SMCS - 1361-11; 1361-12; 1361-15; 1361-16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 2 of 8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 3 of 8
2. Remove four bolts (1) that hold the water pump to the timing gear cover.
1. Make sure the gasket is in place and put water pump (1) in place on the timing gear cover.
2. Install the bolts that hold the water pump to the timing gear cover.
end by:
start by:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 4 of 8
2. Remove shaft (3), seals and impeller (5) from housing (4) with tooling (A) and a press.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 5 of 8
7. Remove seal assembly (10) and shaft (3) from impeller (5) with tool (C) and a press.
8. Install shaft (3) and seal assembly (10) in housing (4) as shown. Remove seal assembly (10)
from shaft (3) with tool (C) and a press. Remove the seal assembly from the housing with a punch
and a hammer.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 6 of 8
2. Install retaining ring (3) that holds the bearing in position with tool (A).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 7 of 8
5. Make an alignment of the bearing spacer with the two bearing bores. Install shaft (6) with a
press from the impeller side of the housing as shown.
6. Install adapter (7). Install bolt (8) and tighten to a torque of 55 ± 5 lb.ft. (75 ± 7 N·m).
7. Install seal assembly (9) into the housing with tool (B) and a press. Do not use a hammer.
8. Install 5P7350 and 5P7352 Spacers (12) as shown. Put impeller (11) in position on the shaft.
Use 5P7353 Spacer (10) and a press to push impeller (11) on the shaft until spacers (12) can just
be removed between the impeller and housing.
b) Use tooling (D) and a press and push the shaft from the adapter side of the water pump until the
spacers can be removed.
c) Install the adapter and the bolt that holds it in place. Tighten the bolt to a torque of 55 ± 5 lb.ft.
(75 ± N·m).
end by:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019
D3B TRACTOR / POWER SHIFT / 23Y00001-UP (MACHINE) POWERED BY 32... Page 8 of 8
Copyright 1993 - 2019 Caterpillar Inc. Fri Aug 2 23:14:25 UTC+0800 2019
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 8/2/2019