Professional Documents
Culture Documents
2) Insert strength loss option for EC8 hinge type 5
3) Improvement about masonry pushover analysis and post processing 6
4) Energy result graph & additional damping ratio in time‐history analysis results 11
5) Add reaction table for each step in pushover 14
6) Select Inelastic Hinge Result Output in Inelastic time history analysis 15
7) Improvement in analysis speed for inelastic time history analysis 17
8) Add result summary table of fiber beam, wall for inelastic hinge 18
9) Revit 2020 interface 19
10) Non‐dissipative element design for slab as per NTC2018 20
11) Improvement of slab design as per EC2 and NTC 21
12) Improvement of non‐dissipative design 22
13) Improvement of inelastic material model 23
14) Improvement of joint design as per EC2 and NTC 24
15) Cyclic shear resistance check as per EN1998‐3:2005 & NTC2018 27
16) Improvement of hinge model as per EC 29
• midas Design+
1) Steel design tool as per AISC 31
2) Anchor bolt module as per ACI 37
midas Gen Gen 2020 v2.1 Release Note
1. Improvement of Column Design
Add Option
• Support seismic design by axial force(P) constant method.
• Apply axial force(P) constant method to all or individual columns
4 /39
midas Gen Gen 2020 v2.1 Release Note
2. Insert strength loss option for EC8 hinge type
5 /39
midas Gen Gen 2020 v2.1 Release Note
3. Improvement about masonry pushover analysis and post processing
6 /39
midas Gen Gen 2020 v2.1 Release Note
3. Improvement about masonry pushover analysis and post processing
SLO
Displacement of limit elastic dSLD x 2/3
SLD
Capacity of SLD
= Min.Displacement of Ve and ¾ Vu
SLV
Last displacement of bilinear x 3/4
Ve Vu
7 /39
midas Gen Gen 2020 v2.1 Release Note
3. Improvement about masonry pushover analysis and post processing
• Add a building type. Building type had ‘New Buildings’ and ‘Existing Buildings’
• Set a default value of D/H according to the building type
C 0.01 0.01
D 0.01 0.01
8 /39
midas Gen Gen 2020 v2.1 Release Note
3. Improvement about masonry pushover analysis and post processing
• Add a building type. Building type had ‘New Buildings’ and ‘Existing Buildings’
• Set a default value of D/H according to the building type
C 0.008 0.015
D 0.008 0.015
9 /39
midas Gen Gen 2020 v2.1 Release Note
3. Improvement about masonry pushover analysis and post processing
Shear Resistance =
Min. [ 𝑉 ℎ𝑡𝑓 ,𝑉 2𝑀 /𝑙 ]
where
Shear Resistance =
where
10 /39
midas Gen Gen 2020 v2.1 Release Note
4. Energy result graph & additional damping ratio in time‐history analysis results
11 /39
midas Gen Gen 2020 v2.1 Release Note
4. Energy result graph & additional damping ratio in time‐history analysis results
12 /39
midas Gen Gen 2020 v2.1 Release Note
4. Energy result graph & additional damping ratio in time‐history analysis results
13 /39
midas Gen Gen 2020 v2.1 Release Note
5. Add reaction table for each step in Pushover
4
1
14 /39
Gen 2020 v2.1 Release Note
• Properties > Inelastic Properties > Inel. Control Data > Select Inelastic Hinge Result Output(Element/General Link)
• Load > Dynamic Loads > Time History Analysis Data > Global Control
Select the element to print Select General Link to print Inelastic Hinge Status Result
- Press ‘Add/Replace’ button after - Press ‘Add’ button after - Check result of selected elements
selecting element on model view - Selecting GL-Link
-
15 /39
Gen 2020 v2.1 Release Note
16 /39
Gen 2020 v2.1 Release Note
• Reduction of analysis time by optimizing the inelastic time history analysis program and improving the output algorithm for
inelastic analysis results
17 /39
Gen 2020 v2.1 Release Note
8. Add result summary table of fiber beam and wall for inelastic hinge
• Results > Results Tables > Inelastic Hinge > Fiber Beam Summary, Fiber Wall Summary
18 /39
midas Gen Gen 2020 v2.1 Release Note
Gen-Revit Link
Functions Revit <> Gen
Structural Column <>
File > Import > midas Gen MGT File Beam <>
Linear Brace <>
File > Export > midas Gen MGT File
Elements Curved Beam >
Beam System >
Truss >
Foundation Slab <>
Structural Floor <>
Planar Structural Wall <>
Elements Wall Opening & Window >
Door >
Vertical or Shaft Opening >
Offset >
Rigid Link >
Cross‐Section Rotation >
End Release >
Boundary Isolated Foundation Support >
Point Boundary Condition >
Line Boundary Condition >
Send Model to midas Gen Wall Foundation >
Area Boundary Condition >
Load Nature >
Load Case >
Load Combination >
Load
Hosted Point Load >
Hosted Line Load >
Hosted Area Load >
Other Material <>
Parameters Level >
Revit 2020 Gen2020
19 /39
midas Gen Gen 2020 v2.1 Release Note
10. Non‐dissipative element design for slab as per NTC2018
20 /39
midas Gen Gen 2020 v2.1 Release Note
11. Improvement of slab design as per EC2 and NTC
Add “Check ratio of x/d” and “Check Stress by Quasi-permanent Load combinations”
Check x/d as per NTC2018 4.1.2.1.2.1 Stress check by Quasi-permanent
21 /39
midas Gen Gen 2020 v2.1 Release Note
12. Improvement of Non‐dissipative Design
* M_Rd
0.9
M_yd’ =
Add Option
22 /39
Gen 2020 v2.1 Release Note
13. Improvement of inelastic material model
Add inelastic model types for Conc. And Rebar (apply partial safety factor)
-Concrete : Parabola Rectangle or Bilinear model
-Rebar : bilinear model (SP63Add inelastic model types for Conc. And Rebar (apply
partial safety factor)-Concrete : Parabola Rectangle or Bilinear model-Rebar : bilinear
model (SP63)
23 /39
midas Gen Gen 2020 v2.1 Release Note
14. Improvement of Joint design as per EC2 and NTC
Detail report
Graphic result
24 /39
midas Gen Gen 2020 v2.1 Release Note
14. Improvement of Joint design as per EC2 and NTC
2) For Ash_req2(EC2:04_5.5.3.3.(4))
Graphic result
Change the results based on the hoop rebar area required
25 /39
midas Gen Gen 2020 v2.1 Release Note
14. Improvement of Joint Design as per EC2 and NTC
• Add option to design selectively for ‘Confined’ and ‘Not confined’ joint condition
Add Option
26 /39
midas Gen Gen 2020 v2.1 Release Note
15. Cyclic shear resistance check as per EN1998‐3:2005 & NTC2018
• Design > result > Concrete Design > Cyclic Shear Resistance
27 /39
midas Gen Gen 2020 v2.1 Release Note
15. Cyclic shear resistance check as per EN1998‐3:2005 & NTC2018
28 /39
Gen 2020 v2.1 Release Note
16. Improvement of hinge model as per EC
29 /39
Gen 2020 v2.1 Release Note
midas Design+
30 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC 341‐16
Calculation
of Unbraced Length
of Beam bracing
Beam bracing
31 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC 341‐16
Calculation
of axial strength
of Point Bracing
-1
Beam bracing
as point bracing
32 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC 341‐16
Calculation
of axial strength
of Point Bracing
-2
33 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC
Design of
Link Stiffener
for I - sections
34 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC 341‐16
Design of
Link Stiffener
for I - sections
35 /39
midas Gen Gen 2020 v2.1 Release Note
1. Steel design tool as per AISC
Calculation
of Beam Strength
with K-brace
36 /39
midas Gen Gen 2020 v2.1 Release Note
2. Anchor bolt module as per ACI 318
37 /39
midas Gen Gen 2020 v2.1 Release Note
2. Anchor bolt module as per ACI
Step 4.
Step 2. Define the layout type & spacing
Define Force Data. Number of Anchor bolt.
(Axial, Moment, Shear, Torsion)
Step 3.
Define Anchor Bolt information.
38 /39
midas Gen Gen 2020 v2.1 Release Note
2. Anchor bolt module as per ACI
Summary Calculation Report Detail Calculation Report
39 /39