Professional Documents
Culture Documents
Page 1 of 6
Shutdown SIS
Previous Screen
i02889660
Operational Checks
SMCS - 4350-535; 5050-535
Before you perform these procedures, refer to Testing and Adjusting, "Machine Preparation" for the
correct procedure for machine preparation.
The following operational checks can be used for the following items:
determine whether the pilot operated hydraulic controls are functioning correctly.
In order for the hydraulic system to function properly, each component in the system must be set to the
correct specifications. Some components must be set prior to the testing of other components. A
component that is not set properly will have an impact on other components in the system.
Note: When any test is performed on the hydraulic system, the hydraulic oil must be at an operating
temperature of 45° ± 5°C (113° ± 9°F). This temperature range is specified for the standard filled oil at
the factory. Use the 164-3310 Infrared Thermometer or the equivalent to measure this temperature at the
canister for the hydraulic filter. To increase hydraulic system temperature, start the engine and operate
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012
226B2 Skid Steer Loader MJH10575-UP (MACHINE) POWERED BY 3024C Engine(S... Page 2 of 6
all hydraulic cylinders for at least five cycles. Move the work tool through the full range of motion.
4. If the automatic leveling switch is in the ON position, then turn the automatic leveling switch to
the OFF position.
5. Run the engine at HIGH IDLE with the pilot operated hydraulic control ( hydrostatic) in the
HOLD position.
6. Operate the lift cylinder through at least five lift cycles. This will ensure that there is warm oil in
the lift cylinders.
7. Tilt the bucket to the full TILT BACK position. Lower the bucket to the full LOWER position.
8. Raise the bucket from the full LOWER position. Record the time from the full LOWER position
to the full RAISE position.
9. Lower the bucket from the full RAISE position. Record the time from the full RAISE position to
the full LOWER position.
10. Raise the bucket to the full RAISE position. Move the hydraulic control to the FLOAT position.
Record the time from the full RAISE position to the full LOWER position.
Table 1
If the speeds are not correct, refer to the Testing and Adjusting, "Hydraulic System Troubleshooting".
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012
226B2 Skid Steer Loader MJH10575-UP (MACHINE) POWERED BY 3024C Engine(S... Page 3 of 6
Note: Perform the tilt cylinder speed test with an empty general purpose bucket. If a general purpose
bucket is not available, then use a load weight of 200 kg (441 lb).
4. Run the engine at HIGH IDLE with the pilot operated hydraulic control ( hydrostatic) in the
HOLD position.
5. Operate the tilt cylinders through at least five cycles. This will ensure that there is warm oil in the
tilt cylinders.
6. Tilt the bucket to the full TILT BACK position. Raise the bucket to the full RAISE position.
7. Tilt the bucket from the full TILT BACK position to the full DUMP position. Record the time
from the full TILT BACK position to the full DUMP position.
8. Tilt the bucket from the full DUMP position to the full TILT BACK position. Record the time
from the full DUMP position to the full TILT BACK position.
Table 2
If the speeds are not correct, refer to the Testing and Adjusting, "Hydraulic System Troubleshooting".
4. Run the engine at HIGH IDLE with the pilot operated hydraulic control ( hydrostatic) in the
HOLD position.
5. Press the switch in order to engage the quick coupler. Record the time that is needed to engage the
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012
226B2 Skid Steer Loader MJH10575-UP (MACHINE) POWERED BY 3024C Engine(S... Page 4 of 6
quick coupler. Press the switch in order to disengage the quick coupler. Record the time that is
needed to disengage the quick coupler.
Table 3
If the speeds are not correct, refer to the Testing and Adjusting, "Hydraulic System Troubleshooting".
Note: Perform the following tests with a general purpose bucket on the machine. If a general purpose
bucket is not available, use a load weight of 200 kg (441 lb).
1. Before you perform these procedures, refer to Testing and Adjusting, "Machine Preparation" for
the correct procedure for machine preparation.
3. Operate the lift cylinders through at least five cycles. This will ensure that there is warm oil in the
lift cylinder.
4. Operate the tilt cylinders through at least five cycles. This will ensure that there is warm oil in the
tilt cylinder.
6. Tilt the bucket forward until the bucket is parallel with the ground.
9. Use a stopwatch to count for one minute. Measure the drift of the cylinders.
Table 4
CYLINDER DRIFT
Cylinders Time Cylinder Drift
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012
226B2 Skid Steer Loader MJH10575-UP (MACHINE) POWERED BY 3024C Engine(S... Page 5 of 6
3 mm (0.118 inch)
Note: If the lift cylinder drift and/or the tilt cylinder drift exceeds the maximum, refer to Testing
and Adjusting, "Hydraulic System Troubleshooting" for probable causes.
10. Start the engine and lower the bucket to the ground.
Note: If the machine drifts to the same side in both forward and reverse, check the chain tension on both
sides of the machine before you proceed with the test.
1. Move the machine to a testing location that is flat, level and 30.5 m (100 ft) long. Allow enough
space on each side of the centerline for any machine drift that could exceed 3 m (10 ft).
3. Start the test outside the test area. The machine must enter the testing location in straight line
travel and the machine must be traveling at full speed. The engine must be set to HIGH IDLE and
the speed and direction control must be positioned fully forward.
4. Measure the amount of drift and record the direction of the drift.
Table 5
Drift
3 m (10 ft)
5. If the machine does not pass this test, refer to the Testing and Adjusting, "Maximum Runout
Test".
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012
226B2 Skid Steer Loader MJH10575-UP (MACHINE) POWERED BY 3024C Engine(S... Page 6 of 6
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 27/06/2012