Professional Documents
Culture Documents
SERIES
TECHNICAL REFERENCE
MANUAL
CONGRATULATIONS
- and WELCOME to the VISTA XM FAMILY!
The purpose of this TECHNICAL REFERENCE MANUAL is to give you, the installer, a
better understandingof the operationand capabilities of the VISTA XM Seriesof products.
From the most basic configuration to the most complex, this manual will help you fully
understand each option, step-by-step. The manual defines the system components,
provides spec.ific wiring and programming instructions (complemented with numerous
diagrams) and describesthe system’soperation. In addition, a comprehensiveglossary is
included to help avoid confusion with the system’sstate of the art terminology.
As always, ADEMCO is there for YOU! Our SALES and TECHNICAL SUPPORT staff
are eagerto assistyou in any way they can, so don’t hesitateto call, for any reason!
East Coast Technical Support: l-800-645-7492 (8 a.m.-6 p.m. EXT.)
West Coast Technical Support: 1-800-458-9469 (8 a.m.-5 p.m. P.S.T.)
LIST OF TABLES
1. DIP SWlTCH TABLE, POLLING LOOP DEVICES.. ................................................................................ -29
2. DIP SWITCH TABLE, WIRELESS DEVICES ........................................................................................... 35
3. BATTERY STANDBY TABLE ................................................................................................................ 55
4. CONTACT ID REPORTlNG CODE DEFlNlTlONS ................................................................................... .66
5. LOW SPEED DIGITAL COMMUNICATOR MESSAGE FORMATS.. ......................................................... .70
6. SUMMARY OF PROGRAMMING COMMANDS ...................................................................................... .73
7. INDEX TO PROGRAMMING FIELDS ..................................................................................................... .74
8. VOCABULARY OF WORDS STORED IN MEMORY ................................................................................ 98
9. AUXILIARY CURRENT DRAW WORKSHEET.. ...................................................................................... .129
10. POLLING LOOP CURRENT DRAW WORKSHEET.. ............................................................................. .129
11. STANDARD PRE-PROGRAMMED DEFAULTS.. ........................... ....................................................... .132
12. STANDARD LOW SPEED 3+1/4+1 PRE-PROGRAMMING.. ................................................................. .143
13. EXPANDED LOW SPEED 3+1&l PRE-PROGRAMMING.. ................................................................. .145
14. ADEMCO HIGH SPEED PRE-PROGRAMMING .................................................................................... .147
15. 4+2 EXPANDED FORMAT PRE-PROGRAMMING ................................................................................ .149
SECTION I
GENERAL INFORMATION
THE VISTA CONTROLS The VISTA XM Controls are microprocessor based programmable systems
which provide up to 9 wired zones of protection, expandable to 64 zones
(wired and/or wireless) when connected to a 2-wire polling bop. The VISTA
XM Series includes the 4130XM, 5130XM. and 4140XM Controls and the
4137 8 5137 Remote Consoles, which are look-alikes to the 4130XM 8
5130XM respectively. Connections to the Control are made via a plug-in
connector, which can be removed without disturbing any of the field wiring.
The phone lines are connected to a separate block located on the
communicator board (4171 XT-XM or 4171XM; ordered separately wtth the
413OXMI 5130XM; 4171 XT-XM included with the 4140XM).
l 4140XM The 4140XM is housed in a metal cabinet, measuring 12’ x 12” x 3’, and
requires the use of either the 4137 fixed message or 5137 alpha-numeric
(allowing use of the 4140XM’s built-in vocabulary) remote consoles. and can
also be used with the 4146 keystation. A SPDT relay, rated @ 2.8 amps, is
built-in for use with a No. 702, or No. 719 (or equivalent) exterior sounder. For
UL mercantile installations, the 414OAlX can be used. The 4140ATX is the
same as the 4140XM, but features a larger, heavier gauge cabinet and a
cabinet tamper switch.
l 4130XM The 4130XM is a self-contained Control with an LCD using 2 numeric digits
for zone identification, and a set of pre-designated English language
.
prompts, for system status (ex: ‘READY’, “NOT READY). A built-in 85dB UL
listed sounder is also included. The Control can be surface or flush mounted.
5130XM The 5130XM is also a selt-contained Control, but with a O-line, 32character
EASY PROGRAMMING The Control can be programmed either on the job site directly from the
keypad, or remotely by using the ADEMCO 4130PC DOWNLOADING
SOFTWARE, an IBM (or compatible) computer, and a HAYES 1200
Smartmodem. (See the PROGRAMMING section for a complete explanation).
All programmed options are stored in non-volatile EEROM memory. This
means that old fashioned PROM chips are no longer needed, and the
program can be changed over and over again, as the needs of a particular
system grow. It also means that the program cannot be bst or changed In any
way if power to the Control is bst. Even if completely powered down for long
periods of time, the program will remain intact.
For installer convenience, the Control is pre-programmed with a set of
‘standam values that is designed to meet the needs of many installations.
These values, however, can be changed to suit the needs of any particular
installation. Specific programming instructions are provided in the
PROGRAMMING section of this manual.
BUILT-IN For end-user wnvenience. the 5130XM and 4140XM (with 5137) contain a
USER’S MANUAL/ “built-in Users Manual. By depressing and holding any of the function keys
DESCRIPTOR REVIEW on the console for 5 seconds, a brief explanation of that particular function
scrolls across the ALPHA-NUMERIC display. For example, if the user forgets
how to bypass a zone, he or she simply depresses the key marked
“BYPASS and holds it for 5 seconds. The information will then scroll across
the display, explaining how to bypass a zone.
In addition, all programmed zone descriptors can be displayed (one at a time)
by pressing and holding the READY key until the key’s instructions appear (5
seconds), then releasing the key. This serves as a check for installers to be
sure all descriptors are entered properly. This feature is also helpful to the
user when there is a need to know the zone number of a particular sensor (as
when bypassing zones).
COMMUNICATIONS The system can be monitored by a central station, via the switched telephone
network. Upon alarms, programmed communicator reports will be transmitted
up to the programmed maximum (swinger suppression) in one armed interval. :--. .
Restoral reports will be sent when the zone is restored for a time greater than
#s physical response time (less than 1 second). In addiiion, the system also
sends system status reports(AC loss, system trouble, etc.). The system also
provides voltage triggers for other communication devices, such as
Ademco’s Long Range Radio system.
..--..
SECTION II
HARDWARE OVERVIEW
- A. VISTA XM SERIES CONTROL PANELS -
COMMON FEATURES l Basic 9 wired zones, expandable to 84 zones (wired, and/of wireless).
l 22 user codes.
l Downloadable (office or site initiated).
l Independent auxiliary voitage trigger outputs for FIRE, PANIC, BURG,
and OPEN/CLOSE.
l ADEMCO High Speed, 4+2, traditional low speed, ADEMCO’s Express
and the new Contact ID communication formats available.
Q
l
L
in 220 word dictionary, plus an additional 5 custom word entries and an
installer’s message can be programmed (ex: ABC Alarms Call 1-800-l 23-
4567).
W’L XM . Removeable terminal strip for easy installation and service.
l Up to a 6AH battery can be used for maximum standby time (gel cell
only!).
l Built-in ‘User’s Manual” and ‘Descriptor Review Mode’ (with 5137 remote
console).
,-,
.n.
- C. DIALERS -
RPM PROGRAMMER
l Portable Programmer for the 4139 and 4191 contacts.
14 HARDWARE OVERVIEW
- F. WIRELESS DEVICES -
TRANSMITTER All transmitters use 9 volt batteries. Either Alkaline type or Kodak lithium
BATTERIES batteries may.be used. Lithium batteries should last 4-7 years under normal
use and have a shell life of 7 years. Transmitters will transmit a ‘Low Battev
signal when battery has 30 days of life remaining.
. 5701
0I 1
El PANIC
l
TRANSMITTER
Programmable for either silent or audible 24 hour atann (can be DIP switch
programmed for zones 62 or 63).
. 5706
H PHOTOELECTRIC SMOKE DETECTOR
l One piece photoelectric smoke detector with built-in transmitter (DIP
switch programmable for zones 48 through 55).
l Built-in 85 dB piezoelectric alarm sounder
l Built-in audible low battery warning.
- G. SOUNDERS -
SECTION III
ZONE TYPE DEFINITIONS
GENERAL The VISTA System albws up to 64 zones of hard-wire, polling loop andlor
wireless protection. Each zone must be assigned to a zone type, which
INFORMATION defines the way in which the system responds to faults in that zone. In
addition, there are three keypad activated zones (PANIC keys) identified as
zones 95.96 8 99, a polling bop supervision zone (zone 97) and two RF
supenrisory zones for each 4260 installed (zones 66-92).
TYPE 1 ENTRY/EXIT #I
Used for the primary entry/exit route (ex: front door, main entrance). The
zone becomes active when the exit delay time has elapsed. Upon entry
through this zone, the system must be disarmed before the entry delay time
has elapsed or else an alarm will occur. The console will beep multiple times
upon entry (as a retinder to disarm the system).
TYPE 2 ENTRY/EXIT #2
Used for a secondary entry/exit route (ex: Garage door, loading dock door,
basement door), where more time might be needed to get to and from the
keypad. The function of this zone type is similar to that of entry/exit #l,
except that the delay times for this zone must be greater than that of #l .
e TYPE 4
violated.
- H. MISCELLANEOUS ACCESSORIES -
4132 Battery back box for 1.2 AH battery (for 4130XM or 6130XM).
4132LG Battery back box for 4.0 AH battery (for 413OXM or 6130XM).
4132-12 Battery Klt - Includes 4132 back box and 1.2 AH battery for
4130XM15130XM.
4132-40 Battery Kit - Includes 4132LG back box and 4.0 AH battery for
4130XM/513OXM.
4134-l 2 Metal Cablnet (12 Inch) w/Relay Module (No. 4148) and
termlnal strlp for 4130XM15130XM.
SECTJON IV
SYSTEM CONFIGURATION (ZONES)
- A. BASIC 9 HARD-WIRED ZONES -
GENERAL The standard system supports up to 9 hard-wired zones. Zones l-8 can be
either supervised (using EOLRs) or unsupervised, and zone 1 can support 2-
INFORMATION wire smoke detectors. Zone 9 is used for fast response devices and is
unsupervised.
ZONE 1 This zone has a 350 milfisecond response and can be assigned to any zone
type and can be set up for EOLR supervision or for closed-circuit
unsupervised use. This zone is the only zone that can support 2-wire smoke
detectors (up to 3 detectors) using an EOLR configuration.
If EOLR supervision is required, wnnect all closed-circuit sensors in series
with one another to TBl-2, (4130XM/5130XM use RED/YELLOW 8
WHITE/BROWN wires) with the 13,000 ohm resistor in series with the loop, at
the tast device and then return the toop to TB24.
If no supervision is required, simply maintain a closed loop with all sensors
connected in series with the loop, between TBl-1 and TBl-2 (or
WHITE/BROWN 8 ORANGE). If the sensors used are open-circuit devices,
such as smoke detectors, each one must be in parallel to the next using the
EOLR configuration. The EOLR must then be placed across the last wired
detector, as shown:
a 414oXM
USES TERMINAL BLOCK
‘USE BRK SMOKE DETECYORS ONLY:
1400 lONKAllON
2400 PHOTOELECTRIC
24WTti PHOTO Wf125o HEAT SENSOR
ORANOE
I wmw I+) RED/YELLOW (A)
413oXM/513oXM BROWN
USES COLORED WIRES I\
I
13.ooo OHM
I END OF LINE
RESISTOR
I
1
ZONES 2 THROUGH 8 These zones have a 350 milliiecond response and can be assigned to any
zone type. They can be EOLR supervised or closed circuit unsupervised, as
required (program field ‘41 determines whether or not these zones will use
the 1,000 ohm EOLR: Enter [l] in field ‘41 to disable the use of EOLR’s on
zones 2 through 8). If programmed for use with EOLR’s. both closed-circuit
and open-circuit devices can be used with the 1.000 ohm EOLR resistor in
series with the bop at the last device, as shown in A below. If the use of
EOLR’s is disabled (‘41-l), only closed-circuft devices can be used, as
shown in B below. Note that the maximum resistance per zone is 300 ohms.
T&l
m-2
,--
TB-2
4140XM -
c
33
Qi
14
GENERAL To expand the system using a P-wire Polling Loop an&or wireless devices, a
INFORMATION 4171XT-XM dialer board, and a 4152LMB Loop Module must be installed as
shown below. (The 4171 XT-XM is factory installed in the 4140XM.)
4171XT-XM Remove the Control’s back cover and discard. Insert three small standoffs
INSTALLATION (supplied) into the three holes on the Control board (marked A. B & C on the
diagram), pressing each until they ‘snap’ into place. Insert the 1Spin male-to-
male adapter (supplied) into the interface socket pin holes on the underside
of the Dialer board as shown.
Guide the adapter pins into the pin holes on the Control bvoard, while
aligning the standoffs with their respective holes in the Dialer board. Be sure
the adapter pins are properly entering the Control board holes, and press
down until the pins are fully seated and the standoffs “snap” into place.
4152LMB Note the 8 square-shaped connector pins on’the dialer board. Position the
INSTALLATION 4152LMB board over that board so that these pins engage the mating
sockets (header) on the underside of the 4152LMB. Press the 4152LMB
down until the pins are fully seated. Secure the No. 4152LMB by means of 3
screws (supplied).
Wires from the 4208 Zone Expander, RPMs, and 4280 are connected to
Terminals 1 8 2 on the 4152LMB. For information regarding polling loop or
wireless expansion, refer to those sections which follow.
-
I ..
GENERAL To expand the system using a P-wire polling bop and remote point modules
INFORMATION (RPMs), a 4171XT-XM dialer board, and a 4152LMB loop module must be
installed, as de&bed in the ZONE EXPANSION MODULE section.
Any of the RPMs can be used, in any combination, to expand the system to a
maximum of 64 zones. For a complete list of available devices, see the
HARDWARE OVERVIEW section
The polling bop can be run in various ways, as shown. Choose the way that
best suits your needs, but make sure that polarity is correct throughout the ,
system. If polarity is reversed at any point, a Ioop short” will occur (displayed
as 197”). Calculate the total current required by completing the Polling Loop
Current Draw Worksheet found in the Summary of Connections section.
BASIC9
HARDWIRED ZONES
4197 LOOP EXTENDER If longer polling bop wire runs are needed or more than MmA current is
being drawn on the polling loop, a 4197 Loop Extender Module must be
used. Diagram 6 shows typical connections. Note that power from a local
power supply is not approved for UL installation.
VISTA
CONTROL NOTECONNECT TERMINALS 2
AND 3 AS SHOWN
n.
POWER SUPPLY: (CONNECT TO AN UNINTER-
RUPTED 12Ot!. 6OHz POWER SOURCE THAT IS ON
ADVISORY The maximum allowable current draw on the polling loop is 64mA. Refer to
the Polling Loop Current Draw Worksheet (found in the SUMMARY OF
CONNECTIONS section) for current draws of various polling loop devices.-If
more than 64mA is being drawn, use of the 4197 provides another loop with
64mA available.
..--.
a SE-KING UP A 4190WH The 4190WH is a O-zone (known as left and rtght zones) RPM. The lett zone
can be used tor cbsedcimult devices, with or without EOLR supervision. and
for open-circuit devices, with EOLR supervision. The left zone can also be
used wlth fast-response (10 millisecond) devices, if necessary. Follow the
chart below for cutting the correct jumpers and choosing the correct resistor
when using the left zone.
The right zone is for closed-circuit, unsupervised use only, and has a
response time of 400 milliseconds. Do not cut any jumpers or use a resistor
on this zone.
JUMPFRS USACj&&EFT Zu ONI Y\
RED: Cut tar fast-response (10 millisecond).
WHITE: Cut tar low current mode (reed type switches); use the
30,000 ohm resistor, provided. Must be cut if BLUE jumper is
cut.
BLUE: Cut tor use with no EOLR (closed-circuit only). Doing this
automatically puts an internal 30,000 ohm resistor in series
with the zone, so the whitejumper must also be cut.
NONE CUT: High current mode: Use the 4.700 ohm resistor, provided,
with mechanical switches in either an open-circuit or closed-
circuit configuration.
EXPLODED VIEW
SETTING UP THE 4208 The 4208 is an 8 zone RPM which is connected directly to the polling loop.
Each zone is end-of-line-resistor supervised and can be used with either
open-circuit or closed-circuit devices. Zone numbers used with the 4208 are
pre-assigned in groups of 8 (except the first group) beginning with zone 10,
and are set via the unit%DIP switches. Note that if more than one 4208 is
used, the system limits the number of zones supported by the first group of
addresses to 7 (zones lo-16 available). If only one 4208 is used, the first
group of addresses can be expanded to 8 zones (zones lo-17 available) by
entering a 1 in program field ‘86. See the PROGRAMMING section tar
information regarding this programming option. See the PROGRAMMING
section for information regarding the use of more than one 4208.
The first two zones are DIP switch programmable for fast response (10
millisecond). Zones connected to this module are factory set for 400
millisecond response. The first six zones are high current zones for use with
mechanical sensors. The last two zones can support only low current sensors
(reed switches, etc.).
PR?ZFAM
SWITCH
NOTES:
A. Uses both sealed (reed) and unsealed (mechanical) ContOctS. F. Requires en external 36.660 Ohm end-o&line resistor (large. H watt.
8. Requires an external 4700 Ohm end-of-line resistor (small W watt. ORANGE-BLACK-ORANGE color bands).
YELLOW-VIOLET-RED color bands). G. Uses 100 microsmps 01 current each.
C. Selectable fast or slow response (both loops as a pair). H. Make certain that the maximum current lrom the control’s polling
0. Uses 1 milliamp 01 current each. loop is not exceeded.
E. Uses only sealed (reed) contacts. 1. If set for zones S-16. loop #l is lost on the 4206.
GENERAL To expand the system using ALERT III wireless transmitters, a 4171XT-XM
INFORMATION dialer board, and a 4152LMB loop module must be installed, as described in
the ZONE EXPANSION MODULE section, and either one or two 4280s (or
4280-8% if only 8 wireless zones are required) must be connected to the
polling loop. Note that the 4280 draws 40mA current. If two receivers are
used, power for the second receiver should be taken from the auxiliary power
connection on the main Control.
NOTE: Unless stated otherwise, references to the 4280 Receiver represent
the 4280 andlor 4280-8 Receivers.
The 4280 RF receiver is a component of the VISTA XM system which
recognizes alarms, status messages and keypad control messages from
ALERT Ill transmitters at 345MHz (U.S.A.). These messages are processed
and relayed to the VISTA XM control panel via a P-wire polling loop. Using a
4280 allows expansion of up to 83 RF zones, plus a wireless keypad (5727).
RANGE The 4280 RF receiver can receive signals from wifeless transmitters within a
nominal range of 200 feet. This gives you greater expandability in installations
where hard wire might not be feasible.
SUPERVISION Each transmitter (except 5701 and 5727) is supervfsed by a check-in signal
that is sent to the receiver at 70-90 minute intervals. If at least one Check-in is
not received from a transmitter within a programmed interval, the keypad will ,,-.
display the transmitter number and ‘CHECK’ will be displayed. See the
section under PROGRAMMING RF OPTIONS. 1’31, for this selection. -
Each transmitter (including 5701 and 5727) is also supervised for low battery
conditions, and will transmit a low battery signal to the 4280 when the battery
has approximately 30 days of life remaining. See PROGRAMMING RF
OPTIONS. 1’28, for LOW BATTERY AUDIBLE ANNUNCIATION selection.
NOTE: After replacing a low or dead battery, activate the transmitter and enter
the security code + OFF to clear its memory of the “Low Battev signal.
The 4280 itself is also supervised three ways:
1. If the cover of the 4280 is removed, an ALARM or TROUBLE will be
displayed depending upon the response programmed in fields 1’08 and
1’09.
2. If the connection is broken between the 4280 and the control panel, an
ALARM or -TROUBLE will be displayed depending on the response
programmed in programming fields 1’08 l? 1’09. This response is usually
that of a DAY/NIGHT or 24 hour type.
3. If, within a programmed interval of time, the 4280 does not hear from any
of its transmitters, an ALARM or TROUBLE will be displayed depending
on the response programmed in fields 1’08 8 1’09. The interval is
programmed in 1’30.
HOUSE The 4280 responds only to transmitters with the same house ID (DIP switch
IDENTIFICATION programmable from 01-31). This prevents system interference from
transmitters in other nearby systems. To make sure you do not choose a
House ID that is in use nearby, put the system in the Sniffer Mode, which is
descrfbed later in this section.
;-.
SNIFFER MODE To check for house fDs being used in nearby systems, set the DIP switches in
the 4280 for a House ID of ‘00’ (all switches up), then enter your ‘Installer
Code’ + [#I + (21. The 4280 will now ‘sniff” out any House IDS in the area and
display them. Keeping the 4280 in this mode for about 2 hours will give a
good indication of the house ID’s being used. To exit the Sniffer Mode,
simply key your installer code + OFF, then set your house ID to one not
displayed in the Sniffer Mode’.
To check that all transmitters have been set for the proper house ID, set the
4280 to the proper house ID and enter the Installer code + [#] + 131. All
transmitter ID numbers that have the house ID set for the 4280 will be
displayed when each transmitter number checks in (up to 2 hours). A faster
way to do this is to faulf each transmitter, which causes a transmission to be
sent to the 4280. Check that the ID number is displayed when the transmitter
is faulted.
BUILT-IN *‘GO/NO GO” This mode helps determine the best location for each transmitter and is
TEST MODE activated by putting the system in the TEST mode and removing the 4280%
(Patented) cover. The receiver’s sensitivity is reduced by half. Once transmitters are
placed in their desired locations and the approximate length of wire to be run
to sensors is connected to the transmittefs screw terminals, open circuit each
transmitter. Do no? conduct this test with your hand wrapped around the
transmitter.
If a single 4280 is used, the keypad will beep three times to indicate signal
reception. If two 4280s are used, the keypad will beep once if the first 4280
received the signal, twice if the second 4280 received the signal and three
tfmes if both receivers heard the signal (which is desirable for redundant
configurations).
If the keypad does not beep, reorient or move the transmitter to another
location.
To exit this mode, replace the 4280’s cover, then enter the installer code and
press OFF. Note that the Receiver’s sensitivity is fully restored when the
wver is replaced.
4280 SET-UP ERRORS All RF zones must be designated as such in their respective programming
fields. tf using a 4280-8, on/y up to 8 zones can be enabled as RF zones. If
more than 8 zones are enabled, the message ‘SET-UP ERROR’
(5130XMI5137) or ‘E8’ (4130XMI4137) will be displayed.
32 SYSTEM CONFIGURATION (ZONES)
.--.
ADVISORIES 1. Do not place transmitters on or near metal objects. This will decrease
range ancVor block transmissions.
2. Place the 4280 in a high, centrally located area for best reception. Do not
place receiver on or near metal objects.
3. The 4280 receiver nust be at least 10 feet from the Control panel or any
remote consoles to avoid interference from their microprocessor.
4. When connecting a door/window contact to a 5711, 5711WM. or 5715
transmitter, avoid a wire length of 20-24 inches. This particular length
decreases range. A shorter or longer length has no effect.
WIRELESS Each RF zone can be programmed to respond as any zone type such as
ENTRY/EXIT, INTERIOR, PERIMETER, etc. (see the section under ZONE
ZONE TYPES TYPES for a complete explanation of each zone type). Desired alarm
responses can be broken down as follows:
ZONf NPF JRANSMTTTFRS
Wf
Entry/Exit Burg i through 63 l
32 through 47 (5775)
l
NOTES:
l
Transmitters set for an ID of 32 through 47 will have a 3 minute bck-
out between transmissions.
.. Transmitter ID’s 48 through 55 have highest signal priority.
... Transmitter ID’s 62 and 63 are unsupervised to allow removal of the
5701 otf premises - signal priority is lower than that of fire, but higher
than burglary.
USING TWO For additional security, some installations might warrant a redundant
RECEIVERS FOR configuration. This means that 2 receivers, connected to the same P-wire
REDUNDANCY polling loop, are used and set to the same house ID. Each of these receivers
listens to all of the transmitters on the job, but If one receiver happens to fail
or is sabotaged, or a path from one or more transmitters is inadvertently
blocked by a metal object, the other one will still be there to detect aiarms.
and fautts, and to supervise the transmitters. Roth 4280s (or 4280-8s) are
fully supervised so that ff one does fail or is deliberately sabotaged, you’ll
know about it.
cI----_
NH -.
USING TWO For installations where the area to be protected goes well beyond the 200
RECEIVERS TO range of the system, or the building configuration preventsgetting the rated
INCREASE COVERAGE range in ail paths to transmitters, a second receiver can be installed. The first
4280 is bcated at one end of the premises and the second 4280 at the other
with both 4280s connected to the same P-wire polling loop.
AREA 12
INTRODUCTION One of the VISTA system’s strengths is flexibility. VISTA permits the use of
homerun hard-wire, polling loop and wireless technologies in any
combination.. The first 9 zones can be efther ail hard-wired. ail wireless (using
a 4280 RF receiver with ALERT iii transmitters), or a combination of both
technologies. Zones 10 through 64 can use either ail polling ioop devices, ail
wireless (RF) devices,or a combination of both technologies.
The selecting of wireless or polling loop zones is programmed in fields 1’18
to 1’25. To enable a zone as a wireless (RF) zone simply enter a “1’ in the
tocation for that zone, as shown:
Ex: SELECT RF (ZONES 1-8) 12345678
01110001
In the above example, zones 2,3,4, and 8 are programmed to be wireless
(RF) zones; zones 1,s. 6 and 7 are hard-wired.
WIRELESS
PERIPHERALS
SMOKE
4280
OR
4280-8
RF
RECEIVER
a I *
41520
LM@ a & RPM DEVICES
n POLLtNG LOOP
. f
RPM RPM
\ b b
COMBINATION CONFIGURATION:
BASIC 9 HARD-WIRED ZONES USING HARDWIRE, P-WIRE POLLING LOOP
AND WIRELESS TECHNOLOGIES
SECTION V
SYSTEM CONFIGURATION (PERIPHERALS)
- A. REMOTE CONSOLES -
GEP;IERAL Both the 4130XM and the 5130XM supply up to 28OmA (2OOmA for UL
certificated installations) of auxiliary power for remote consoles and/or other
auxiliary devices such as motion detectors or 4-wire smoke detectors. The
4140XM supplies up to 700mA for non-UL usage and up to 400mA for UL
applications. You must keep this in mind when adding remote consoles so
you don’t “overdraw’ current from the panel. This would result in a battery
which is never fully charged, or possibly a blown auxiliary power fuse.
In the event you need more than the allowed number of remote consoles,
you can use a second #1350 power pack to power up to 7 extra 4137s or up
to 4 extra 5137s. Instead of using the panel’s auxiliary power connection to
the red and black console lead, connect the Positive (+) terminal of the 1350
to the blue console lead, and the Negative (-) to the black lead. As long as AC
power is present, these extra consoles are active. If AC is lost , the system’s
back-up battery will take over and only the consoles powered from auxiliary
power will be active.
NOTE: lf using a 4140XM, make sure you power at least 1 remote console
from auxiliary power, otherwise there would be no means of controlling the
panel during an AC loss.
4137 - For use with the 4130XM. 4140XM or 5130XM Controls
-6OmAcurrentdraw
- Power up to 4 consoles from the 4130XM and 5130XM (non-UL)
l 5137
- Power up to 7 consoles from the 4140XM.(nonUL)
‘USECONFIGURATIQN(A) OR (8)
SEPAAATELY...NOT
TOGETHER!
I.
a.
- .-
...
-.*.
-.
-5 <:
UPT02 740s
wo0mEacoyBlNA1IoNs-
0 OR (D) 1 740 IN PARALLEL WITH 3 BRK PA400
. ? -1TO SOUNDER
+
VISTA
CONTROL BROWN
t-r TRlGaER
TRIGGER
NOTE:THE 4148
12VDC MODULEMUSTBE
4 AH MIN 3AFASTBLOFUSE LOCATU) As CLOSE
BATTERY POWERFUSE As POSSIBLETO
BATTERY
m 4148 RELAY MODULE l
l TIKI 4148 IS NOT UL
APPROVED FOR USE WnH
THE 413OXMI!33OXM.
Dlagmm 17. 4148 RELAY MODULE
719 SIREN
UP t0 two 719s can be used,. wired in parallel, as s,hown:
..-\.
1. Going beyond the above mentioned limits will result in a blown auxiliary
power or relay tuse.
2. The 4148 relay is rated at 2.8 Amps @ 28 VDC max. If sounders or drivers
other than the ones mentioned above are used, make sure the maximum
current draw does not exceed 2.8 Amps.
CAUTION: These sounders are polarized (+) and (-)! If polarity is reversed,
the sounder will not work!
:--. :
ADVISORY If the EOLR is not at the end of the loop, the zone is not fully supervised. The
system will not respond to an open circuit within the zone.
ZONES 2 THROUGH 8 These zones can suppart as many 4-wire Smoke detectors as can be
powered, when programmed as a FIRE zone, type 09, in program field ‘02.
There are only two requirements: (1) The zones must be configured for
EOLR supervision, and (2) A normally-closed, momentary Switch must be
Installed in series with the power to the detectors in order to allow reset of the
smoke detectors after an alarm. The detectors must be wired in parallel, with
the EOLR at the last detector, for full supervision. as shown:
ANY ZONE.2THRUS TB2
.
USE OF RELAY
SMOKE
DETECTORS I II II
lmo OHM
END OF LINE
RESISTOR
FOLLOW INSTRUCTIONS FOR INDIVIDUAL SUDKE DEMXDRS FOR PRDPER INSYALLATIDN AND WIRING
FDR CtRtXJll AND PDWER
D&gram 21. ZONES 2-8 EOLR SUPERVISED FOR CWIRE SMOKE DETECTORS
ADEMCO’s VISTA XM SERIES TECIYNICAL REFERENCE MANUAL
42 SYSTEM CONFIGURATION (PERIPHERALS)
,-,
POLLING LOOP Can be added to the g-wire Polling Loop via the 4152LME loop module, on
SMOKE DETECTORS zones 10 through 84 (as programmed in fields ‘05, 1’02, 1’03, 1’04 and
(4192S0, 4192SDT l’OS).These detectors have a built-in RPM which is DIP switch
programmable. They are wired in parallel to the polling loop, and do not need>
OR 4192CP) auxiliary power or a separate reset switch. The polling bDp provides power
and reset signals to the detectors,as well as alarm and trouble signals from
the detectors.
4152LMB
POLLING
LOOP I
WIRELESS Can be used on zones 48 through 55 as long as that zone is enabled for RF
SMOKE DETECTORS usage in program fields 1’23 and/or 1’24, and are programmed as FIRE
(5706) zones, type 09, in fields 1’03 an&or 1’04. These detectors have buiit-in
transmitters and are powered from a single 9 volt battery. A 4280 RF receiver
must be connected to the a-wire polling loop driven by the 4152LMB loop
module. These transmitter/detectors are DIP switch programmable and are
fully supervised for bw battery and check-in.
MODULE
4260 RF RECEIVER *
+
e
(+I(-) B%iE
‘UP TO 0 #Nemo
QQOO oElFcTonscAN
BEUSLD.
GENERAL Select a mounting site with the following notes in mind: Best coverage will be
INFORMATION obtained if the mounting site is selected such that the likely direction of
intruder motion is across the pattern of protection.
Avoid locating the unit where central heating radiators, flames or heating
outlet ducts are within the protective zones.
Avoid locating the unit in direct sunlight or directly above strong sources of
heat.
Avoid locating the unit on unstable surfaces.
Avoid running alarm wiring close to heavy duty electrical cables.
Make wire connections as shown:
POLLING LOOP PIR The 4196 is a quad element passive infrared detector with a buitl-in RPM that
(4196) is connected directly to the- polling loop. It provides up to 40 feet of
protection, using a wide angle mirror, or up to 70 feet of corridor protection
using the long range mirror (both mirrors are provided with the unit). A right
zone is available for use with closed-circuit devices and can be programmed
for a different zone type than the PIR. The 4196 can be flat wall mounted or
comer mounted, using the mounting plate provided. Programming of the
unit’s address ID is accomplished via the units DIP switches (see Table 1 in
the preceding section). Refer to the instructions accompanying the 4196 for
patterns of coverage and procedures for changing mirrors.
LiiFEl
WIDE ANGLE LONG RANGE
MIRROR MIRROR
POLLING LOOP PIR The 4275 is a dual element passive infrared detector, with a built-in RPM, that
(4275) is connected directly to the P-wire polling loop. It provides up to 45’ of
protection, using the wide angle mirror, or up to 70’ of narrow (corridor or
curtain) protection, using the long range mirror (both mirrors are provided).
The PIR can be mounted flat on the wall or comer mounted, with the
mounting plate provided. Programming is done via the DIP switches (see
Table 1 in the preceding section). Refer to the instructions accompanying the
4275 for patterns of coverage and procedures for changing mirrors.
Connect as shown:
.-
WIRELESS PIR The 5775 is a battery operated, wireless, dual element passive infrared
(5775) motion detector and provides wide angle protection with a range of up to 35’.
The PIR features a pulse count option and can be mounted flat on the wall or
corner mounted. Programming of house ID, transmitter ID and pulse count
option is done via the unit’s DIP switch. Note that there is a 3 minute delay
between transmissions to preserve battery life. Refer to the instructions
accompanying the 5775 for additional details.
OFF ON
4171 XT-XM/4171 XM The 4171XT-XM is factory installed in the 4140XM Control. For the
4130XM/5130XM Controls, connect the 4171 XT-XM or 4171XM as shown
INSTALLATION below. Note that If any zone expansion is being used, the Dialer board is
already installed (see ZONE EXPANSION section).
DIGITAL
coMuuwIcAlIoN 13CIN INTERFACE
INTERFACE BOARD coNWEclOn IAo*CIER
PiNS INSERTED FAOU
/ BELOW1
I3FIN YALE.16
e \I NALE ADAPTER
\ QwlyUNlCAllON
INlERFACE
PIN W)LES
Terminal
2. INCOMING PHONE LINE (Tip)
Terminal
3. INCOWlING PHONE LINE (RING).
Terminal
4. LOCAL HANDSETS (RING).
Terminal
5. LOCAL HANDSETS (TIP).
Connect
the green flying lead to a proper earth ground.
WARNING: To prevent the risk of shock, disconnect phone lines at telco
jack before servicing the unit.
1:’ , , , , ,-..--., , -, T ,
z
0
- USE RJ31X
FCORD NO.
A MO-366.
/
lOl@l@lO
w -
\ \ / / i
LOCAL PHONES
PHONE LINE
CONNECTOR BLOCK
BLACK
6 (-) AUX POWER (TB2-13 OR RED/BL .ACK)
‘~‘~*ORANGE JUMPER
MUST BE CUT!
(4171XT-XM ONLY)
l l l eoe l e
\
VOLTAGE TRIGGERS
NOfE: IF KEYSWITCH
OPTION IS SELECTED.
AUXILIARY ALARM OUTPUT
TRIGGERS ARE NOT AVAILABLE.
GROUND (-1
oPEN/cLosE(+)5voLTso\mAolJTPuToN~
BURGLARY/AUDIBLE PANIC/AUXILIARY 1 (+) 5 VOLTS @ ImA
(READY LED) SILENT PANIC/DURESS OLlTPUT ON ALARM’
\
-(ARMED LED)-FIRE I
ADVISORY If the keyswftch option is selected (field ‘15) the alarm trigger outputs are
disabled.
An optional Remote Keyswttch, can be used for remote arming and disarming
of the system. If used, and programmed by the installer (‘15=1), a normally-
open momentary switch is connected across a 1000 Ohm resistor on zone 7
of the control panel (Zone 7 must be given up as a protection zone but must
still be assigned a zone type). A momentary short across this zone will arm the
system in the .AWAY’ mode. If the short is held for more than 3 seconds, the
system will arm in the -STAY mode. (All zones designated as zone types 4 or
10 will be automatically bypassed). After the system has been armed, the
next time zone 7 is shorted, the system will disarm.
An optional closed-circuit tamper switch (model 112) can be wired in series
with zone 7. so that, if the switchplate is removed from the wall, the tamper will
open, disabling keyswitch operation until the system is next disarmed from
the console.
NOTES:
1. When keyswitch is selected, a 1000 ohm resistor must be used
regardless of whether.or not zones 2-8 are selected to use end of line
resistors.
2. Only one keyswitch with LEDs can be supported by the system’s power
supply. If more than one keyswitch is to be used, a 688-12 switching
module must be used to boost the signals used to drive the LEDs.
LED indications are defined as follows: .’- -.
DY
DISARMED & READY
ARMED AWAY
:-.
SELECTING SITES Proper selection of mounting location and height is important for optimum
viewabifity of the LCD display on the console. A bcatfon in which lighting k
dire&y above the console should be avoided, since this can shadow the
dkptay. For optimum viewing, the console should also be mounted so that
the display k slightly below eye level to ensure that the system’s users will
look down at the display. For Alpha Console users, refer to the VIEWING
ANGLE ADJUSTMENT paragraph later in this section for instructions for
adjusting theviewing angle of the LCD.
SURFACE MOUNTING 1. Use the template provided (on a separate sheet) to mark the posltiins on
the wall for the screw mounting holes and the cutout for the interface
wiring. Use wall anchors for the screws and make the cut-out in the wall no
larger than indicated on the template. DO NOT use a Xerox copy of the
tenplate. as it will increase in size by about 1O?h.
2. Pull the interface wiring in the wall through the cut-out.
3. Remove the console’s back cover. The securing screw at the front of the
wnsole must be removed to release the back cover (see Diagram 31 for
scrqw focatiin).
4. Pass the interface wiring through.the opening in the back cover and
through ttre 4143 Expansion Ring (lf used), then mount the back cover
to the wall surface wlth screws. See Diagram 31.
5. Splice the interface wiring to the console wires (or to the wires on the
interface connector supplied wfth 4137s). A wiring diagram k provided in
the SYSTEM CONFIGURATION (PERIPHERALS) section. Insulated
solderless wire splices (eg. 311) may be used for spfiiing. Check wire
connections carefully before splicing.
6. Attacf’r the main tidy of the console to the wall-mounted bar& cover. The
console is prop&y attached when ff snaps into pface. Use the securing
screw (previously removed) to secure the console to the back oover (see
Diagram 31 for location of screw hole), then Insert the small name plate
supplied into the recessed opening to cover the screw head (see
Diagram 33).
7. See Diagram 31 B for mercantile/industrfal mounting wfth metal cabinet.
Notes:
l The No. 4134 Surface Mount Metal
Cabinet is available in tow sizes; an 6”
x 8’ x 2” version (No. 4134-67 and a
larger 12” x 12’ x 3. version (NO.
4134-l 5-) that can hold various
modules in addition to the battery.
Also available is the 4134-l 2” (12 x 12
\ No 4134-S Metal Sur- x 3) with 4146 relay module for use
tace Mount Cabinet with the 702 or 719 siren.
l Knockouts for the interface wiring have
also been provided on the rear and
sides of the cabinet.
\ wlrlaowispmvieeafof
mounting the VISTA Applications:
Control andCommunciatof l Concrete, Brick or Cement/Cinder
on the trrmt ot the unit
Block wall construction
l Wherever else keypad is normally
‘TenntilRr@s(tihm mounted on cabinet
wrap push-in wiring) are
omwaaafoffietawinna
J nm4130XM85130XMan3 ULmercemite
listed. For UL mercantile jobs use me
414oATx.
I \ “Not Listed
Battery sRs inscte cabinet
when using lhe larger No. 4134-l 5 C&met. there is
&so mom tot a No. 675 Gtomt San Module. No
659EN Tew Lme Faull Mamor. No. 4208 Zone
Expanderand/or other modules.
SPRING (NOTE
YETALCUF END)
IS Too TNICK.
BREAKOFFTHESCORED WING
NOTE:
4-s is-x r-sww
WALLOPENING ISAEOUIRED FOR
FLUS4YOUNTING
l No. 311 Wii Bptices permit meter probe insertion at one and.
l standard plu~411wiring hmess comes wifh prfmripped leads for ease of
installation.
l If End-of-Line Resistors (EOLRs) will not be mounted at the zone sensor
fuMesI from the control. there is e software option to delete their use on
zones 2-8. H-r, since this eliminates zone supervision for short cir-
cuit& it is not ~ndeb(onlyN.C.typecontactscenbeusedilEOLRs
are not used).
l A wire ID tag has been incfuUed for the tiiing of wire assignments.
l Controfs can support UPto 3 P-wire smoke detectors on zone 1. (BRK 1400.
2400 or 24OOTH).
l A larger No. 4162LG Battery Back Box is evaitatrtetor holding two 6V. 4.OAH
kad acid batteries (No. YA-NP46).
FLUSH MOUNTING lf a “rough-in’ ring (4133) has been previously installed in the wall (during new
WlTH TRIM RING construction; see Diagram 35) disregard step 1 and proceed to step 2, since
the required opening for the console is already present. If a wall plate (4136)
is installed over the rough-in ring, remove the plate to expose the opening.
Note: The four mounting tabs on the right-hand side of the 4133 rough-in
ring must be broken off before flush mounting can be performed.
1. Cut out a 4-314’ high by 6” wide opening in the wall between studs, no
less than 1-l/2g from either stud. See Diagram 34 (A). Use the template
provided to mark the cut-out.
2. Insert the four l-1/2’ long #6 screws through the mounting holes in the
supplied Trim Ring and then attach the four metal securing clips, as
shown in Diagram 34 (B). Use only two or three tums of each screw,
allowing the metal clips to hang freely. The clips must not protrude
beyond the sides of the Trim Ring or you will not be able to install the Trim
Ring into the cutout in the next step.
3. Install the trim ring into the opening in the wall with the hinge clasps to the
right, as in Diagram 34 (D). Making sure the trim ring is straight, tighten
each clip screw, making sure that the attached clip slides down into its
guide track. As each screw is tightened, the clip will be drawn up against
the wall (see Diagram 34 (C)). Tighten each screw until the trim ring is
securely held against the wall. DO NOT OVERTIGHTEN.
4. Referring to Diagram 34 (D). install the Console as follows: engage the
hinge clasps on the trim ring with the notches located in the back (right-
hand side) of the Console’s front panel. Swing the left side of the panel
toward the trim ring (the panel will pivot on the hinge clasps), and press
firmly until the panel “snaps. closed.
5. Use the panel securing screw (supplied with the Console) to secure the .f---.
left side of the panel, as shown in Diagram 34 (D). Insert nameplate into
the recessed area to cover the securing screw (see Diagram 33).
INSERT NAMEPLATE
INTO RECESSED
AREA (COVERS SCREWI
SECURING
SCREW
NOttbSZ
l The No. 4133 Rough-in Ring should
only be installed as shown, with the
No. 4133 Rough-m Ring right angle bend on the left-hand
II I for phsterkheet rook walls
side. This positions a bend in the
ring’s opening at the top of the con-
FhfdWiWlQatlaChHft0 trol, shielding the control from
loo0 in Rounh-m Rii flaking plaster and sheet rock gyp-
sum that could fall into it otherwise.
A loop is provided on the right angle
bend to which a wire tii can be
attached to clamp the field wiring in
place for convenient access when
the alarm system is installed.
l The No. 4136 Cover Plate is used in
installations where the builder is only
sold the alarm wiring, and the sale of the
individual alarm system is a final pur-
chaser option. The cover plate will
remain in place if the alarm system is
never sold.
less Steel Cover Plate
for Rough-in Ring Applications:
l Residential
0 Professional office
5130XM/5137 ONLY Insert the end of the small, key-shaped tool (supplied) into the small hole to
the left of the console display window (the adjustment screw is recessed in
this hole). Turn the adjjstmem screw to the left or right until optimum viewing
is achieved. Be sure to take the height of the users into account when
making thii adjustment.
BACK-UP POWER In the event of an AC power toss, all VISTA XM Controls are supported by a
back-up, rechargeable gel cell battery. (see the HARDWARE OVERVIEW
section for a Gsl of recommended batteries). Up to a 6.0 amp-hour battery can
be used, for maximum standby time (see chart below).
POWER-UP PROCEDUREI. VVrrethe 1350 (1360) DC Power Pack first (before the battery), making
sure polarity is correct and the terminal strip (or harness) is connected to
the Control panel. Do not plug in at this time.
2. Connect all auxitiary devices, such as consoles, PM. etc.
3. Plug the 1350 into an AC outlet. Check that the Auxiliary Voltage
measures between 13.5 and 14.0 volts DC. tt under 13.5 volts, too much
current is being drawn from the Control. See the SPECIFICATIONS
section for the current draw of each device.
4. Connect the battery as shown in the POWER CONNECTIONS diagrams.
Do not connect the battery lf Auxiliary Vottage is below 13.5 volts. as this
will prevent the battery Irom being fully charged.
TB2 T02
\ I
3 4 s 6
QOOOJ
I
EARTH
GROUND
- (+I
wi6a
18 MC DC POWER (+I f-1
@BsomA PACK
t-1
12 VOLT STANDBY
GEL CELL BAnERY
b wAl4 mqulfd for
CAlJTlOw: ‘OBSERVE FOLARIlV! UL imtallations)
‘KEEP WIRE RUNS AS SHORT AS POSSIBLE!
‘4eOAH MINIMUM BAmERY CAPACITY
‘B.OAll MAXIMUM BATTERY CAPACllY
VISTA
CONTROL
STANDBY
BAmERY
S.&H MAXIMUM!
CALmoM 0BBERvEPolARm
KEEP WIRE RUNS AS SHORT AS POSSIBLE1
INSTALLER’S CODE The installer programs the Installefs Code initially as part of the programming
(USER #l) procedure (see PROGRAMMING THE SYSTEM), and this code is the only
code that permits re-entty into the programming mode (unless ‘98 has been
previously used to exit the programming mode, see below). The Installers
Code can also be used to perform normal system functions, but cannot
assign temporary codes.
The system also provides an Installer Code lock-out feature, which prevents
the use of the Installers Code from re-accessing the Programming mode after
the initial programming. This feature is activated by pressing ‘98 to exit
Programming mode. The only way to access Programming mode once this
feature is activated, is by powering down the system and powering up again,
and then pressing both the and # keys at the same time within 30 seconds
l
MASTER CODE The Master Code is the code intended for use by the primary user of the
system when performing system functions, and is a permanent code. The
(USER t2) factory default master code is l-2-34. For addiiional security. the Master
Code can be used to assign up to twenty temporary codes, which can be
used by secondary users of the system who do not have a need to know the
Master Code (supervisors, employees, cleaning personnel. tenants, etc.).
Each user (ID number 0322) can be assigned a temporary code which can be
individually eliminated or changed at any time.
The installer is considered user 1. The person to whom the Master code is
assigned is considered user 2. In some applications (commercial installations,
for example), user 2 (with Master Code) will be the primary user of the system.
In other applications, user 2 (with Master Code) may not actually be the end
user of the system (apartment building owner, for example).
Note that the Master Code (assigned to user 2) and all temporary codes can
be used Interchangeably when performing system functions (a system armed
with a useb temporary code can be disarmed with the Master Code or
another use6 temporary code).
Temporary user 3 also has the ability to assign and eliminate other temporary
user codes (users 4-21). User 22 can only be assigned or changed by user 2.
.-.
TEMPORARY CODES Temporary Security codes can be assigned and deleted by user 2 (with
(USERS %3 - A22) Master Code) or user 3 as follows:
User 2: Master Code + CODE key + User # (0322) + Temporary Code
User 3: User 3’s CODE + CODE key + User # (04-21) + Temporary Code
User numbers must be entered as O-digit entries. Single digit user numbers
must, therefore, always be preceded by a ‘0” (example, 03. 04, 05, etc.).
Make sure the end user understands this requirement.
User 2 can assign temporary codes to all users, 3-22. User 3 can assign
temporary codes only to users 4-21. The system will emit a single beep when
each temporary code has been successfully entered.
Note: When a temporary code is inadvertently repeated for different users, or
one user’s code is anothers duress code (see below), the lower .user number
will take priority.
To delete temporary codes, do the following:
Master Code + CODE key + User # + Master Code
Note that user 3 cannot delete the temporary code assigned to user 22.
IMPORTANT!: Unless Ademco Contact ID reporting is used, only user
codes #1 - #15 can uniquely report to the central station using the
communication formats provided. Users #16 - #22 will report as User #15, if
enabled for open/close reporting, for the other repotting formats.
DURESS CODE The VISTA System duress code is a means of sending a silent alarm to a
central monitoring station if the user is being forced to disarm (or arm) the
system under threat. This feature is only useful if the system is connected to n
a central station. When the system’s Auxiliary Voltage Triggers are
connected to another communication’s media (Derived Channel/Long Range
Radio), note that duress is signalled on the same trigger that signals silent ._
panic (whereas duress has its own unique report when digitally
communicated).
The duress code is simply the usual security code, but with the fourth digit
increased by 1. For example, if the security code is ‘1 2 3 4’, the duress
code is ‘1 2 3 S. When used, the system will disarm (or arm), but will also
send a silent alarm to the central station. There will be no indication at the
console that an alarm was sent.
Note that duress codes are not available for security codes ending in the digit
‘9’.
IMPORTANT!: Users of temporary codes should be instructed to enter
their codes carefully, to avoid the possibility of accidentally entering the
duress code.
Do not assign sequential temporary codes 1 digit apart from each other (8x.
4096, 4097, 4098) as this will cause a Duress to be sent each time (one
users code is another useI’s duress code).
,Y----.
; ‘.
INTRODUCTION The VISTA XM system provides four modes of burglary protection: STAY,
AWAY, INSTANT, and MAXIMUM. In addition, if any zones are faufted pffor fo
arming (NOT READY wncfitiin). the console can dspfay them one at a time,
and specific zones can be sefecfivefy bypassed.
When an alarm occurs, wnsofe sounding and external sounding will occur,
and the zone(s) in alarm will be displayed on the console. Pressing any key
will silence the wnsole sounder for 10 seconds. Disarming the system will
silence both console and external sounders. When the system is disarmed,
any zones that were in an alarm condition during the armed period will bs
displayed (memory of alarm). To clear thisdisplay. simply repeat the disarm
sequence (enter the securfty code and press the OFF key).
The VISTA XM consoles also feature chime annunciation, and 3 panic key
pairs (for silent, audibie, fire or personal emergency alarms) which can notify
the central station of an atann wndiion, if that service is connected.
Note that ff QUICK ARM is enabled (field ‘29). the [#] key can be pressed
instead of entering the security code, for any of the arming procedures listed
below (Away, Stay, Instant, Maximum).
DISARMED Before armlng, the system must be In the READY wndition.(all zones must
NOT READY be intact). If the ‘NOT READY message appears, press the READY r] key to
display all faulted zones.
ARMING: AWAY This mode arms all protection zones, interior and perimeter and provides
(CODE + AWAY) entry/exit delays.
Enter the security code and press the AWAY key.
ARMING: STAY This mode arms perimeter zones only, allowing free movement inside, and
(CODE + STAY) provides entry/exit delays.
Enter the secutfty code and press the STAY key.
ARMING: INSTANT This mode Is similar to STAY mode, but INSTANT mode eliminates the entry
(CODE + INSTANT) delays. Exit delay remains.
Enter the sewrity code and press the INSTANT key.
ARMING: MAXIMUM This mode Is simiiar to AWAY mode. but MAXIMUM mode eliminates the entry
(CODE + MAXIMUM) delays. Exit delay remains.
Enter the security wde and press the MAXIMUM key.
BYPASSING ZONES If desired, the system can be armed with one or more zones left unprotected
(CODE + BYPASS + (bypassed). To bypass zones, first be sure the system is disarmed. Enter the
ZONE NUMBER) security code, press the BYPASS key, and then enter all the zone number(s)
(using 2-digit entries) that are to be bypassed. Single digit zone numbers
must be preceded by a zero (i.e. 01 for zone 1, etc.). After all entries are
made, the console will display the bypassed zones one at a time. Once zones
have been displayed, the system can be armed as usual. Failure to wait for
the sequential display can result in the loss of the bypasses. Bypasses are
removed when the system is .disarmed. Note that Fire zones cannot be
bypassed.
To display bypassed zones (before arming the system), enter the security
code and press the BYPASS key. All bypassed zones will be displayed
sequentially.
CHIME MODE The system can be set to annunciate any opening of entry/exit or perimeter
(CODE + CHIME) zones (doors, windows) while the system is disarmed. Enter the security
zone and press the CHIME key. Repeat to turn chime mode off.
USING THE BUILT-IN For 5130XM or 4140XM with 5137 consoles only.
USER’S GUIDE An abbreviated Use6 Manual is stored in the system’s memory, and can be
particularly useful to the end user if the printed User’s Manual is not
conveniently accessible when the user needs to perform a seldom used and
unfamiliar system procedure. The Built-in User’s Guide is displayed by simply
pressing any of the function keys (e.g., OFF, AWAY, STAY, MAXIMUM,
BYPASS, INSTANT, CODE, TEST, READY, #, and CHIME) for approximately
5 seconds and then releasing it. Abbreviated instructions relative to the key
that has been pressed will then be displayed (2 lines of text are displayed at a
time). This function is available when the system is in the armed or the
disarmed state.
pqF
For 5130XM14140XM wfth 5137 consoles, these panic keys can also be
programmed with an alpha descriptor.
IMPORTANT: For the Panic functions to be of practical value, the system
must be connected to a central station.
- C. TROUBLE CbNDlTlONS -
The word ‘CHECK” on the Console’s display, accompanied by a rapid ‘beeping’ at the Console, indicates that
there is a trouble condition in the system. The audible warning sound can be silenced by pressing any key.
Instruct users to call for servtce immediatety upon seeing any of the following messages.
o-
l A display of ‘LO BAT (5130XMI5137) or “BAT (4130XMI4137) and a
zone descriptor, accompanied by a once per minute beep at the Console
indicates that a tow battery condition exists in the wireless transmitter
displayed. The audible warning sound may be silenced by pressing any
key. A display of ‘SYSTEM LO BAT (5130XM15137) or ‘BAT with no
zone ID (413OXM/4137) indicates that a low battery condition exists with
the system’s backup battery.
. A display of -4280 SET UP ERROR’ (5130XMI5137) or ‘E8’
(413OXMI4137) at the console indicates that a 4280-8 receiver is being
used in a system wtth more than 8 RF zones programmed. 11this is not
corrected, none of the zones in the system will be protected. If more than
8 RF zones are desired. a 4280 Receiver must be used.
POWER FAlLUdE If the POWER indicator is off, and the message ‘AC LOSS (513OxM15137)
or -NO AC’ (413OXM14137) is displayed, the Console is operating on battery
power onty. Check the folbwing:
l At the premises, check circuit breakers and fuses and reset or replace as
necessary.
l Check to see that your system’s plug-in Power Pack has not been
accidentally pulled out.
l Instruct the user to call a servtce representative immediatety if AC power
cannot be restored.
NOTE: The power indicator may extinguish immediately upon power failure,
but the display message could take up to 2 minutes to appear.
Conversely, the power indicator may light immediately upon power
being restored, but it could take up to 2 minutes after power is
restored for the display message to change.
The System’s alarm memory retains all events for a period of 10 days. starting
at the time of the first event. Upon expiration of the 1Way period, all history
is automatically erased and the alarm memory will reset. The next 1O-day cycle
will begin when the next event occurs.
To display the 1Oday history, enter the security code and press the 0 key.
Recall by service personnel (using the entry indicated above) will display all
events that have occurred from the start of the lo-day cycle to the time of
recall. Note that Recall will end any lo-day cycle in progress. The LCD display
on the 4130XM14137 console will indicate the number of the zone in which
the event occurred (e.g., 01. 02. etc.). accompanied by the word CHECK
(trouble), ALARM and, tf appficable, FIRE, to describe the type of went that
occurred in the displayed zone. If a 5130XM15137 is used, an alpha
descriptor of the zone will be displayed in addition to its zone number. If mole
than one event had occurred, the events will be displayed in numerical
sequence. Each display will appear for 1-2 seconds, then the next event wilt
be displayed. When all events have been displayed, the displays are
repeated.
To exit Recall, enter the security code and press the OFF key. At this point,
all existing memory is erased and the alarm memory is reset. The 1O-day cycle
will start again only when the next event occurs.
--.
TWO PHONE NUMBERS Two different telephone numbers (primary and secondary: fields “33 8 ‘34)
can be programmed. Note that if a secondary phone number is used, a
secondary subscriber ID number must be assigned (see fields ‘32 8 ‘90).
The telephone number dialed depends on the report to be sent and on the
report routing option (dual, split or back-up reporting) that is enabled. If dual
reporting is enabled (field ‘51). all reports are transmitted to both numbers. If
split reporting is enabled (field 1’31). each report is transmitted to its
assigned number. Back-up reporting is also available, and is automatically
enabled tf a secondary phone number is programmed. Backup reporting
sends reports to the secondary number only if attempts to get through
to the primary number are unsuccessful.
After dialing the telephone number, the communicator will wait up to 30 or 60
seconds, whichever is programmed (field ‘45 8 ‘47), for the receiver’s
acknowledgment tone (handshake). The communicator will begin
transmitting its reports when the acknowledgment tone is received. If the
acknowledgment tone is not detected during the programmed waiting
period, then the communicator will hang-up and pause for 30 seconds,
insuring that any incoming calls are disconnected before attempting to dial
again (Vu&Jam”). The communicator will make 8 attempts to transmft a report
to one or both telephone numbers, depending upon the report routing
Option programmed. After the eighth attempt, the communicator will hang-up
and a Comm Failure (513OXMS137) or FC message (4130XM14137) will be
displayea at the Console.
REPORTS Reports are transmitted using the programmed format. When a report is
transmitted, up to 4 message rounds are sent. After each round, the
communicator looks for the receiver’s kissoff tone. if the kissoff tone is not
detected, the communicator will pause for 2 seconds before transmitting the
next round. If kiss-off is not heard after the four rounds, the communicator will
hang up and redial to try again.
- 8. COMMUNICATION FORMATS -
IMPORTANT!: l Up to 15 eventskones and uiers can be unlqueiy reported
using 3+114+114+2 Ademco Low Speed, SescoalRadionlcs
or Ademco Hlgh Speed (DTMF) formats.
l Up to 27 events/zones and 15 users can be uniquely
reported using 4+2 Express (685 Receiver requires Rev. 4.3
or higher software) or 4+2 Expanded Zone reporting
(Ademco Low Speed, SescoalRadionics).
l Up to 64 events/zones and 22 users can be uniquely
reported uslng Ademco’s Contact ID format (685 Receivier
requires Rev. 4.4 or hlgher software).
TYPES The VISTA XM Controls can send reports in any of the following
communication formats:
3+1&l
l ADEMCO LOW SPEED, 10 pps, standard or expanded.
l3+1&l SESCOA/RADIONICS, 20 pps, standard or expanded.
4+2, ADEMCO 10 pps or SESCOAlRADlONICS 2Opps. standard or expanded
l
ADEMCO LOW SPEED ADEMCO LOW SPEED is a pulsed format which responds to a 1400 Hz
handshake and kiss-off, and transmits data with 1900Hz pulse tones @ 10
pulses per second (pps). A typical message consists of two rounds which
must be,verified by the receiver. If both rounds match, the message is
validated, and kissed off. A complete standard report consists of either a 3 or
4digit account number followed by a l-digit alarm code. Even though 2
rounds are sent, only the valid report is displayed on the receiver:
Ex:1234 3
In expanded reporting, two messages are sent, two rounds per message, the
first being the account number and alarm code, the second being the zone
(or channel) to which the alarm was assigned. A complete expanded report
consists of a 3 or a-digit account number followed by a ldigit alarm code,
then the alarm code is repeated, followed by the channel number:
Ex:l 234 3 (code3)
3 3 3 3 9 (channel9)
To enable Ademco Low Speed reporting, enter a 0 in “46. To enable
expanded lw speed, enter 1 in ‘55-•60 for the desired expanded reports.
4+2 “EXPRESS” ADEMCO’s new Express format provides the same intonation as the 4+2
Expanded format, but with three differences:
1. The data is transmitted in DTMF (Dual Tone Multi-Frequency, known as
“TouchTone’, at the rate of 10 characters per second). This greatly
decreases the time il takes a report to go through to central station. An
average 4+2 Low Speed report might take as long as 20 seconds to
complete its report, but 4+2 Express takes under 3 seconds!
2. -Two message rounds are eliminated by the use of a checksum digit.
‘Instead of the communicator sending 2 rounds per report. it sends only 1
round with a checksum digit at the end. Doing this also helps in
decreasing the time it takes for a report to be sent. (CHECKSUM is
explained further at the end of this section).
3. The handshake frequency is 1400 Hz followed by 2300 Hz, and the
kissoff frequency is 1400 Hz.
To enable 4+2 Express, enter a 2 in field ‘48, and a 1 in field ‘53. Then use
fields l 72 through ‘81 to program up to 27 zones for unique event reporting.
IMPORTANT:
1. Do not make any entries in fields ‘61-‘71.
2. If the installation uses zones 28-64 and this format is selected, events in
zones 28-64 will not be transmitted.
LIMITATIONS 1. When using Ademco high speed, remember there are only 15 channels
available, plus a duress channel. If more than 15 zones are being used,
they will have to share channels.
2. With high speed reporting, channels 9-15 cannot report troubles or
bypasses. Use these channels for zones that will not have to repon these
conditions.
LIMITATIONS If reporting in 3+1 Low Speed format with checksum, be sure that the 695
Digital Receiver is also set for 3+1 with checksum, otherwise there might be
confusion as to the meaning of the reports. lf reporting in 4+1 Low Speed do
not enable checksum because ll will appear as a 4+2 report on the central
station’s receiver, and might cause confusion as to the meaning of the report!
4+2 e
SSS(S) A =W) A SSSS ACh
WA) Ch
Trouble -(S) T =@I T SSSS TCh
lmna
bW= =(S) B =W) B SSSS BCh
BBB(B) Ch
AC Loss sss(S) E =W) E ssss EAC
EEE(E) AC
Low Battery MS) L =w L ssss LLb
UYL) l.b
Open Sss(S) 0 =w 0 ssss ou
oow) u
Close sss(s)C =(s) c ssss cu
=w) u
CanCel sss(S) x sss(S) x ssss x0
Test SSS(S) Te SSS(S) Te SSSS Tee
Power Up Reset us p =m p ssss PGI
ProgramTamper SwS) M sss(S) M SSSS Me
Restore:
sss(s) R Ssso R SSSS RCh
RRR(R) Ch
AC Loss SSSOR sss(S) R ssss RAC
RRR(R) AC
Low Battery sss(S) R sss(s) R SSSS RLb
RRR(R) Lb
TrOLltIle sss(s)m SSS(S)Rt SSSS RtCh
RTRTRT(RT)Ch
SSS(S) RB SSS(s)Rb SSSS RbCh
RBRBRB(Rb)Ch
Where:
SSS or SSSS = Subscriber ID - Low Battery Code (1st digit!
A kb f pwnmh\! me (2nd dlgfl)
f gpcode
:h = ChannelNumber : - CbseCode
T = TmubleCode = User Number
B =Bvpgss- Ye - Test Code
E = AC Loss Code (1st Dill) = Restore Code (Alarm, AC Loss, Low Battery)
AC f ACiCyEe (2rxf digit) ll = Restore Code (Trouble)
X Rb- Restore Code (Bypass)
= PowerUpResetCode
rA o Program Tamper Code
SECTION X
PROGRAMMING THE SYSTEM
- A. GENERAL INFORMATION -
LOCAL/REMOTE . The Control can be programmed from the keypad or from a computer terminal
using the VISTA XM Downloading software (see DOWNLOADING section).
PROGRAMMING When programming from the 5130XMI5137 consoles, prompts for each field
description (only field number will be displayed on the 4130XMHl37
consoles) and field number will be displayed; also, each entry is displayed as
it is keyed in. After programming, values that have been entered in each field
can be reviewed and, if neccesssaty. modified.
PRE-PROGRAMMED The system is shipped with a set of standard preprogrammed values that are
designed to meet the needs of many installations. However, these can be
COMMUNICATION altered by the installer to suit the specific needs of a particular installation or
FORMATS installatiin company. In addition, four sets of pm-programmed communicator
defautts are available which may be loaded by the Installer. each set designed
0 for a specific communication format (see SUMMARY OF CONNECTIONS
section for lit of values). These, too, may be altered to suit the needs of a
particular installation.
IMPORTANT!: If any of these communication preprogrammed formats are
to be used, they must be programmed (using the appropriate command)
before any other field programming is performed.
TWO SETS OF The programming fields are grouped into two sets of add&es. The first set
of fields includes addresses ‘00 - l 90, and is accessible as soon as
PROGRAMMING FIELDS programming mode is entered. When in the first set of fields, the
5130XMI5137 consoles will display ‘PROGRAM MODE’ and will put a
hyphen in front of the field address. while the 4130XMI4137 consoles will
simply display the fiild address.
The second set of field addresses is accessed by pressing ‘94. while in
programming mode, and are referred to In this document by a -1. in front of
the address (ex. 1’39). The alpha consoles (513OXM15137) will indicate this
by displaying the words “ALT PROGRAM MODE* on the top line of the
display, and displaying a .l’ in front of the field address (i.e. field ‘32 of the
second set of addresses is displayed as 132). The 4130XMI4137 consoles
will display the word CHECK when the second set of addresses is accessed.
The second set of fields includes addresses 1’00 - 1’49. To return to the
first set of fields, press ‘99. noting that the alpha consoles display the words
‘PROGRAM MODE”. and the word CHECK disappears from the 4130XMI
4137 displays.
2. Sat Standard Defaults Once the Programming mode is entered, clear the system’s memory by
pressing 37. This ensures ail program fields are set to their factory set, pre-
programmed values.
3. Set Communlcatlon If the system is to be connected to a central station via telephone line, the
Format Defaults appropriate communication format settings should be programmed now.
(If deslred) VISTA provides four sets of preprogrammed communication formats, which,
lf used, fill all appropriate fields with preset values (see SUMMARY OF
CONNECTIONS section for Tit of values). These values can be modiii later
as desired. To pre-program a particular communication format, use the
following chart:
~~~~~~
4. Program the data flelds To program the first set of fiilds (fields 00-90). simply press the r] key plus
the P-digit field address (for example, press ‘01 for field ‘01). then make the
required entry. To program the sewed set of fields (fields l*OO-1’49). press
l 94, and note that the alpha consoles display the words ALT PROGRAM .
MODE, and the 413OXMI4137 consoles display the word CHECK. Once the
console indicates that it has accessed the second set of addresses, simply
press the r] key plus the P-digit field address (ex. ‘01 for field 1’01) and 1
make the required entry. To return to the first set of fiilds, press ‘99.
When a data field has been wnpletely programmed, the console WI %eep.
three times and then automatically display the next data field address in
numerical order. lf the number of digits that you enter ln the data fiilcl Is less
than the maximum pennltted (for example, phone number), the console
displays the fast entry and watts. To proceed, the next data field address to
be programmed must be entered manually (for example, press ‘05).
To review the contents of a data field, key # prus address (for example #05).
me fielcfs entries will be diifayed, but no changes can be made.
5. In case of errors If an address is improperty entered, the console will display FC . If a program
entry is improperly entered (for example, a larger number than that whii is
permitted), the console display will go blank. In either case, simply m-enter
the correcf number.
7. Exlt Progmmmlng Mode When all fields have been entered and checked, exit programming mode by
pressing either ‘98 or ‘99. A second entry of ‘99 is required If the exit is
being done from fields 1’00 and above. To prevent re-access to
Programming mode using the Installers code, use ‘98. The only way to re-
access Programming mode is by depressing both the r) and I#] keys at the
same time within 30 seconds of power up. Exiting by using ‘99 always allows
reentry into Programmfng mode using the Installers code. Either way of
exftii will allow access via downloading.
.-.
-.
‘39
User:
I 9 110 111 112 113 114 1 ’ 1 1 01 Ol Ol 01 01 01 01 01
15 16
1’00 I 1.1 I 1 I 1 1 01 01 01 01 01 01
User: 17 16 19 20 21 22
- C. ZONE DEFINITIONS -
RESPONSE TYPES The followlng Is a llst of the available response type
asslgnments for each zone:
00 - Assign for unused zones
01 = ENTRY/EXIT (Delay #l), Burglary
02 = ENTRYIEXlT (Delay #2), Burglary
03 = PERIMETER, Burglary
04 = INTERIOR, FOLLOWER, Burglary
05 = TROUBLE BY DAY/ALARM BY NIGHT. Burglary
06 = 24HOUR SILENT
07 = 24-HOUR AUDIBLE
08 = 24HOUR AUXIUARY
09 = FIRE
10 = INTERIOR, DELAY, Burglary
COMMENTS: For response type entries, enter the P-digit response type
using the numerical codes listed at the beginning of this section. To
designate a zone as a Right loop or an RF zone, enter a 1 in the
appropriate location. Right loops refer to the use of the right loop on a
4190WH and 4196. RF zones reter to the use of wireless devices. If
zones l-9 are to be used as wired zones, or if a zone is used as a wired
right loop zone, be careful not to select that zone for RF because it will
then be ignored, as the wireless option will take precedence. If zone 7 is
to be used for keyswitch ArnVDiiarm operation, enter 10 as lts response
type.
ZONES l-8 RESPONSE ‘02 I I I I I I I I I I I I I I I
SELECT RF 1.18 , I I I I I I I .-.
ZONE: 1 2 3 4 5 6 7 0
. .
ZONES 9-16 RESPONSE ‘03 I I I I I I I I I I I I I
DESIGNATE RIGHT LOOP ‘06 0 I I I I I
SELECT RF 1’19 c I I I
9 10 11 12 13 14 15 16
\
ZONES 17-24 RESPONSE ‘04 I I I I I I I I I .
DESIGNATE RIGHT LOOP ‘07 I
SELECT RF 1’20 c A
17 18 19 20 21 22 23 24
- D. RF OPTIONS -
FIRST 4260 1’26 III
RF EXPANDER SELECT I
(011) COMMENTS: Enter 1 if first 4260 is installed. Enter 0 if no 4280 is
installed.
SECOND 4260
RF EXPANDER SELECT
1’27
I I
(O/l 1 COMMENTS: Enter 1 if 2nd 4260 is installed. Enter 0 if only one or
no 4260 is installed.
IMPORTANT!: If second 4260 is installed, cut Blue jumper on 2nd
4260.
RF TRANSMITTER 1’26 I
LOW BATTERY I
ANNUNCIATION ENABLE COMMENTS: Enter 0 if audible beep and display annunciation upon
(O/l 1 RF transmitter low battery condition is desired only in disarmed state.
Enter 1 if audible beep and display is desired in both armed and
disarmed states.
RF .TRANSMllTER 1’29 El
LOW BATTERY I
REPORT ENABLE COMMENTS: Enter 1 if a trouble message for RF transmitter low
(O/l 1 battery conditions is to be sent to the central station. Enter 0 if no
report for transmitter low battery is desired. Note that a trouble
message will be sent for a transmitter supervision failure independent
of this selection.
4260 CHECK-IN
INTERVAL
1’30 1 1 I lolsl
(02-15 or 00 for no check-in) COMMENTS: Enter the check-in monitoring interval in a-hour
increments; enter 02-15 (4-30 hours). Failure of a receiver to
receive any RF signal within the time entered will result in activation of
the response type programmed for zone 90 for the first 4260 (4260-
6)-and zone 66 for the second 4260 and their related communication
reports.
NOTES: If a zero is programmed; super-&ion of the RF receiver will
be disabled (response types for zones 66 and 90 are disabled).
RF TRANSMITTER 1.31 I [ ll
CHECK-IN INTERVAL 1
(02-15 or 00 for no check-in) COMMENTS: Enter the check-in monitoring interval in P-hour
increments; enter 02-15 (4-30 hours). Failure of an individual
transmitter to send a supervision signal within the time entered will
result in a trouble response and related communication report.
NOTES: If a zero is programmed, this feature is disabled.
DISABLE
KEYPAD
WIRELESS 1’46
I III
(O/l ) COMMENTS: Enter 1 if wireless keypad is not to be used (disable
keypad). Enter 0 if wireless keypad is used.
DISABLE TROUBLE
SOUNDER FOR
1’49 I El
RF SUPERVISION COMMENTS: Enter 1 to disable trouble sounding for transmitter
(O/l 1 check-in failure; enter 0 il audible sounding is desired.
- E. SYSTEM OPTIONS -
ENTRY DELAY #1 l 09 rj mj
(01-15 times 15 seconds or 00 for no delay)
COMMENTS: Enter the entry delay time (multiply entry by 15
seconds for actual delay time), up to a maximum delay of 225
seconds (entry 15 times 15 seconds), for the zone assigned to Entry
Delay #l .
EXIT DELAY #2
1 1 1 lolel
‘12
(01-l 5 times 15 seconds or 00 for no delay)
COMMENTS: Enter the exit delay time (muflipfy entry by 15 seconds .P :
for actual delay time), up to a maximum delay of 225 seconds, for the
zone assigned to Exit Delay #k?. Note that this delay must be bnger ._
than Exit Delay #I.
.-..
KEYSWITCH ARM/DISARM l 15 I
ENABLE I
(O/l ) COMMENTS: Enter 1 for keyswitch enable: other&se, enter 0.
Requires the use of zone 7 wired bop (zone 7 no longer available as
protectiin zone when used for keyswltch operation).
NOTE: Zone type 10 nust have been entered for Zone 7 in field ‘02.
Reports opening&losing by user #7 ff reporting is enabled in field
‘52. lf this field is enabled (enter l), the fire and panic alan voltage
triggers automatically become ARMING and READY status outputs
for support of the Keyswltch LEDs.
POWER UP IN ‘26 I
I
PREVIOUS STATE
(O/l 1 COMMENTS: Ente?l if it is desired that upon power-up (after a low-
battery is sensed), the system will assume the system status prior to
power down. Enter 0 if it is desired that the system will atways power
up in a disarmed state. When the system powers up armed, an alarm
will occur 3 minutes after arming if a zone is faulted. When so armed,
reports closing as User #7 if open/close reporting for User #7 was
enabled in Address ‘52.
CONFIRMATION OF ‘18 El
ARMING DING ENABLE I
(O/l 1 COMMENTS: Enter 1 to enable haff second external alarm sounding
(‘ding’) at either the end of exit delay #l , if OpenlCiOSe reporting is
not selected, or when kissoff is received from central station if
Open/Close reporting is programmed. Enter 0 to disable the “ding”.
CONTROL ALARM va
I
SOUNDER DISABLE I
(O/l 1 COMMENTS: Must be zero for 4140XM. For 4130XM1513OXM. enter
1 to disable internal alarm sounder. Does not apply to remote
consoles.
CONTROL ALARM
SOUND SELECTION ‘26 I 0 lol
(O/l ) COMMENTS: For 4130XM/5130XM, enter 1 for a sweeping sound
at the Control upon alarm. Enter 0 for steady sound. This field does
not apply to the 4140XM nor to the 413715137 consoles.
0 00 08
01 : 09
: A
3 8: E0 NoT usE)
: 12
: xi 13
Ear; 14
; 8; FW#l 15
..-.
COMMUNICATOR SPLiT
REPORT SELECTION
1’34
1 m-
(O/1/2) COMMENTS: Enter 0, 1, or 2, in accordance with the following:
0 = split reporting disabled; 1 = alarm, alarm restore 8 cancel reports
sent to primary Teiw number, ail others to secondary Telco number;
2 = open/close 8 test reports sent to secondary Teico number and ail
other reports to primary.
.!
I. . I
.
COMMENTS: Enter 0 if 30 second central station receiver
acknowleqige..?atjime for secondary phone number. is desired.
Enter 1 ‘for 6Q+-e~xl acknowledge wait time. For UL installations,
select 30 seconds.
.-r
:.a:..
.- BWGLAky A&ARg:
‘CO4MUNl6ATION DELAY
*j&8
I 161
COMMENTS; FnJerp for m. tj$,iayon burglav~alarm w~mmunicatiin,
~, .f -
or 1 for 1O-secondde@y(no’delay on ‘%I-hotir repoti j.
‘.-
-. .
. .
- :
--
;
.’ i
. .-L I_.
._ .
..
- , ‘7 r 7
, .
_
;ii-’
i. ,-.. _
- H. REPORTING OPTIONS -
SINGLE MESSAGE l 49 El
TRANSMISSION WITH I
CHECKSUM VERIFICATION COMMENTS: Enter 1 to send a verification digit to validate the
(O/l 1 message at the receiver without having to send two message
rounds.
NOTE: Selection applies to both primary and secondary phone
numbers, and is valid for 3+1,4+2, and Ademco High Speed reports.
ZONE
REPORTTYPES RESTORE
ENABLE ‘69 I I I I 1 1 11 11.11 13
.
(O/l 1 TYPE: 1234
] 11 01 01 OJ
. 5-6 7 8
.: 7.1.i:..
.mE*m
. 910
I
COMMENTS:. Enables Restore reporting for individual zone types
Enter 1 to select restore reporting for the zone type; enter 0 to
inhibit restore reports.
:_
_.
;.. ,:-
, =..i
ZONE: 41 42 43 44 45 46 47 46
- L. REPORT CODES -
(3+1/4+1, 4+2 STANDARD, ADEMCO HIGH SPEED & CONTACT ID FORMATS)
ALARM REPORT CODES ‘66 I I I I I I I I I I I I I I I 1
FOR EACH CHANNEL 1
CHANNELS 1-8 CHANNEL: 1 2 3 4 5 6 7 8
- N. DOWNLOADING OPTIONS -
CENTRAL STATION l 35 111
DOWNLOAD PHONE #
When in thii mode, the console keys perform the following functions:
[3] &~~s both alphabetand actual words in ascendingalphabetical
Note that the first letter of the alphabet appears after the zone number,
and that the zone number.is automatically included with the proposed
description.
4. Select the first letter of the desired description‘ (note that *A” is already
displayed). Use key 131to advance through the alphabet and key [l] to go
backward. For example, assume the desired description for zone 1 is
BACK DOOR. Press key (31repeatedly (or hold down the key) until ‘B
appears; then press key (61.to display the first available word beginning
with B. Repeatedlypress key [3] to advance through the available words
until the word BACK is displayed. Press key [l] to move backward
through the word list.
5. For selection ot the second word (DOOR), press key IS]. “A” will now be
displayed again after the first word selected . Press key 13) until the
desired first letter of the second word appears (in this example, l D”).
Then press key [6] to display the first available word beginning with ‘D’.
Press key [3] repeatedly until the desired word (DOOR) appears.
6. If you wish to add a third word (provided there is sufficient space for if in
the display), repeat step 5 for that word.
7. When ail desired words have been entered, press key [S] to store the
description in memory.
6. To review the zone descriptions, key [#I]plus zone number
(e.g., #Ol). To edit zone descriptions, key [‘I plus zone number (e.g.. ‘01)
9. To exit the zone description mode, key ‘99.
NOTE: Alpha descriptor entry can be accomplished locally at the 5137
console or remotely using a 4130PC Downloader.
3. Now key 00 to get into the mode which will allow the custom words to be
created. The foifowingwill bs displayed: ED ?
l
.n.
CREATING A Normally, when the sy6tem Is In the disarmed state, the following display is
present on the Console.
CUSTOM MESSAGE ““DISARMED”” READYTO ARM
DISPLAY Part or ail of the above messagecan be modlfied to create a custom in6taiier
(iNBTALLER’B MESSAGE) message. For example, ““DISARMED *** on the first line or READY TO
l
message.has been stored in memory, press 00 and then press key [5].
The new’message should be displayed.
8. Key l 99 to exit the descriptor/programmingmode.
SECTION XI
DOWNLOADING
WHAT IS Downloading allows the installer or central station operator to remotely
access. program, and control the security system over normal telephone
DOWNLOADING? lines. Anything that can be done directly from the keypad can be done
remotely,using DOWNLOADING.
HOW DOES DOWN- At the protected premises, the VISTA XM Control panel must be connected
LOADING WORK? to the existing telephone line via the 417lXT-XM dialer board (refer to the
PHONE LINE CONNECTIONSsection).
Assuming a new installation,the installer must do 3 things:
(1) Enter the programming mode and load the factory defaults by
pressing ‘97. This loads specific information needed to complete a
successful first wmmunication.
(2) Program a phone number to which the computer and modem are
attached (‘35). This number is known as the “CALL-BACK NUMBER”.
(3) Programthe number of rings at which the VISTA XM is to ‘answer
f44). Thii k known as the ‘RING COUP.
The panel k now readyfor its first wmmunicatiin.
In order to remotelyaccess. wntroi, or program the alarm panel, a ‘link’ must
be establishedbetween the computer and the wntroi panel, as follows:
1. The computer calls up the Control panel. (The phone number for each
customer k entered Into the wstomefs account file on the computer).
2. The Control panel ‘answers- at the pre-programmed ring count and
executes a handshakewith the computer.
3. The computersends a requebtfor call-back to the Control panel.
4. The panel acknowledgesthe request and hangs up. During the next few
seconds, the Control panel will process the request making sure certain
encrypted information, received from the computer, matches its own
memory.
5. Upon a succes6fuimatch, the Control panel will seize the phone line and
call the computerback.
6. The computer answer6, usually by the second ring, and executes a
handshakewith the panel.
7. The panel then send6 other default information to the computer. if this
information matches the computeh information, a successful link ‘a
established.Thii is known as being *ON-LINE”.
HOW SECURE IS Accessing the Control panel from a remote location is protected against
DOWNLOADING? compromise by the use of 4 levels of security protection: .,-
1. Security Code Handshake: The subscribers account number as
well as an B-digit central station ID number (CSID) (known only to the
office) must be matched between the Control and computer.
2. Hang-Up and Call-Back: The Control panel will ‘hang-up’ and call
the computer back at the pre-programmed number only if the security
codes match, as explained above.
3. Data Encryptlon: Ail data that is exchanged between the computer
and Control panel is encrypted to reduce the possibility of anyone
Wpping~ the iine-and conupting the data.
4. Operator Access Levels: Up to 15 operators can have access to the
DOWNLOADER, each having their own log-on code. However, each
operator can be assigned one of three levels of access in both FILE and
COMMAND functions, as follows:
FILE ACCESS:
Read Only: able only to look at the database; cannot change any
information, and cannot see the customeVsaccess codes.
Part ReadMlftte: able to look at and change all information. except the
customets access codes.
Full ReadMlrlte: able to look at and change any and all information in
the database.
CONTROLlCOMM ACCESS:
Read Only: able only to Upload and arm the system. Not able to
DISARM, BYPASS, or change any programmedinformation.
Part ReadMlrlte: able to ARM, BYPASS, UPLOAD, DOWNLOAD
but cannot shutdown the system.
Full ReadMlrlte: able to perform all control and status commands, as ..-.
well as shutdownall or pan of the system.
ADVISORIES: 1. Alarm and trouble responses and reports are disabled during on-line
time. Should an event occur during this time, the responsewill take place
and the report will go through as soon as the remote access sequence k
completed.Alarm and trouble conditions are not ignored, they are simply
delayed.
2. The keypads are inactive during downloading communication, and
resume normal functions after hang up. All keypad entries are ignored
during on-line time.
=.
-. I.
. _
...
SECTION XII
TESTING THE SYSTEM
USING TEST MODE After the installation is completed, the Security System should be thoroughly
tested as follows:
1. With the System in the disarmed state, check that all zones are intact. If
DISARMED - Press r] to show fautts (5137) or NOT READY (4137) is
displayed, press the [‘I key to display the descriptors of the faulted
zone(s). Restore faulted zone(s) if necessary, so that “‘*DISARMED”’
READY TO ARM (5137)or READY (4137) is displayed.
2. Enter the security code and press the TEST key. The external sounder (if
used) should sound for 3 seconds and then turn off (the system is
operatingon the backup battery only at this time).
NOTE 1. The system will not enter the Test mode il the battery voltage is
too low, if the battery is not connected, or if any communication
messages are waiting to be transmitted.
NOTE 2. As a reminderthat the system k in the Test mode, the Console
will sound a single beep at lbsecond intervals if no protection zones are
violated.
NOTE 3. In the Test mode, no alarm reports will be sent to the central
station. Also, the external sounder (if used) will not be activated.
Dgors and windows Open and close each protected door and window in turn. Each action should
produce three beeps from the Console. The descriptor for each protection
zone will appear on the Console display.
0 Motion detectors Walk in front of any interior motion detectors Listen for three beeps when the
detector senses movement. While it is activated, its descriptor will remain
displayed on the Console. Note that wireless PlRs will have a 3 minute
lockout between transmissionsto consewe battery life
Smoke detectors Follow the test procedure provided by the manufacturer of each smoke
detector to ensure that all detectors are operational and are functioning
pmwriy..
NOTE: A 2-w& smoke detector display will not clear until the Test mode is
exited.
Turning off TEST mode Enter the security code and press the OFF key.
TURNING THE SYSTEM 1. Fully explain the operation of the system to the user by going over each
OVER TO THE USER 2 of tts functionsas well as the Use& Manual supplied.
in particular, explain the operation of each zone (entry/exit, perimeter,
interior, fire, etc.). Be sure the user understands how to operate any
emergencyfeature(s) programmedinto the system. .f---.
IMPORTANTI: In the spaces provided in the Use6 Manual, record the
Entry and Exit Delay times, and those functions that have been
programmedinto the avaiiablepairs of PANIC keys (’ and #, 1 and l , 3 and
#I*
3. Make sure the user understands the importance of testing the system at
least weekly, folbwing the procedureprovided in the Usefs Manual.
i
Regular maintenance and inspection (at bast annually)by the installer and frequenttesting by the user are vital to
continuous satisfactory operation of any alarm system.
The installer should assume the responsibility of devebping and offering a regular maintenanceprogramto the
user as well as acquaintingthe user with theproperoperationand limitationsof the alarm system and Its
component parts. Recommendationsmust be includedfor a specifii programof frequent testing (at teast weekly)
to insure the system’s proper operation at all times.
SECTION XIII
SPECIAL UL REQUIREMENTS
PRODUCTS NOT UL LISTED l 675 Ground Start Module
9 4148 Keyswitch
l 4133 Rough-InRing
9 4136 cover for No. 4133 Rough-InRing
l 4145 Splice Box Kii
l 4149 702 Siren Junction Box Kit
l ABB1031 Motor Bell and Box
702 OutdoorSiren
l
EARTH GROUND
FAl WOUL
Diagram 38. No. 414oATXUL GRADE A INSTALLATION
106 SPECIAL UL REQUIREMENTS
INSTALLATION NOTES 1. All wiring between AB12 and 4140ATX must be in conduit, and all
conduit holes (knockouts) on the Control panel shall be used or blocked
from access. (See Diagram38,414OATXGrade A Installation.)
2. Use 12V 4 AH (minimum)Battery.
3. Value of End-of-lineresistor is 1K ohms (‘41=0).
4. Entry Delays cannot exceed 80 seconds for UL Commercial Burglary
Listings.
5. ~e&tirsout cannot be less than 18 minutes for UL Commercial Burglary
-.
Diagram 39. COMMERCIAL GRADE AA CENTRAL STATION 4140ATX CONNECTED TO No. 696UL STU
ADEMCO’s VISTA XM SERIES TECHNICAL REFERENCE MANUAL
SPECIAL UL REQUIREMEh’TS 107.
. 698UL
CABINET
TAMPER
LINER
CABINET 9
1
MOUNTING’
SCREW
-w-e-
- . AB 12 BELL BOX -I
ABIZ-1
AR12-2
I .@- SWITCHES
I I I
I’ .
o- INNER (1
I BOX
TB2 ML WIRING IN CONDUIT
I
OUTER I
EOL:: I
BOX
I
FROM
1.4 EARTH GROUNO
c-y
UL 1610 GRADE A CENTRAL ._.STATlON,~,MERCANTlLE BURGLARY
INSTALLATIONS -USING iQNQ.1 . RANGE RADIO
IMPORTANT!: Requires the use of No. 414OATXControl.
NOTE: Not a UL Listed application.
BELL CONNECTIONS Audible alanns must be provided-by the use of AB12 Bell in Box..The AB12
must be mounted so that it can b;e;lheard dutside the protected area.
INSTALLATION NOTES 1. All wiring between AB12 and 4140ATX must be in conduit, and all
conduit holes (knockouts) on the Control panel shall be used or blocked
from access. (Bee Diagram38.)
2. Use 12V 4’AH (minimum)Battery.
3. Value of End-of-line resistor is li( ohr& (‘41=0).
4. Entry Delays cannot exceed 60 seconds for UL Commercial Burglary
- Listings.
5. Bell timeout cannot be less than 18 minutes for UL Commercial Burglary
Listings.
6. If 4199WH Dual Point RPM are used, tamper detection in Reid Address
‘24 must be enabted (enter 0).
7. Field ‘16 Confirmationof Arming Ding must be enabled.
8. Field l 18 AC Loss Alarm after 4 hours must &* enabled.
9. Field ‘27 24 Hour Test must be enabled.
10. Op&Close reporting must be enabled. ‘-.
-: ,
XMIT OUTWT ox
t TOREMOTELEDw('
GQvurrlc4lon
L
11
rn’
D
414oAT-x
110 SPECIAL VL REQUIREMENTS
BELL CONNECTIONS Audible alarms must be provided by the use of AB12 Bell in Box..The AB12
must be mounted so that it can be heard outside the protected area.
INSTALLATION NOTES 1. All wiring between AB12 and 4140ATX must be in conduit, and all
conduit holes (knackouts) on the Control panel shall be used or blocked
from access. (Bee Diagram36.)
2. Use 12V 4 AH (minimum)Battery.
3. Value of End-of-lineresistor is 1K ohms (‘41~0).
4. Entry Delays cannot exceed 60 seconds for UL Commercial Burglary
Listings.
5. Bell timeout cannot be less than 16 minutes for UL Commercial Burglary
Listings.
6. If 4190WH Dual Point RPM are used, tamper detection in Field Address
‘24 must be enabled (enter 0).
7. Field ‘16 Confirmationof Arming Ding must be enabled.
6. field ‘16 AC Loss Alarm after 4 hours must be enabled.
I I
a
4
0@6 I 06 0T
I f t
TELEWONE LINE TO
NO YINIMOWURM OR I
-LocAlE
- (ORANQE ’
.,-.
Diagram 42. UL GRADE AA CENTRAL STATION INSTALLATION USING 445 GRADE AA
LINE SECURITY TRANSMfTTER
ADEMCO’s VISTA XM SERIES TECHNICAL REFERENCE MANUAL
UL 1610 & UL 365 GRADE A CENTRAL STATION & POLICE
STATION MERCANTILE BURGLARY INSTALLATIONS USING HIGH
LINE SECURITY DIRECT WIRE TRANSMISSION
IMPORTANT!: Requires the use of No. 4140ATX Control.
BELL CONNECTIONS Audible alarms must be provided by the use of AB12 Bell in Box..The AB12
must be mounted so that lt can be heard outside the protected area.
INSTALLATION NOTES 1. All wiring between ABlP and 4140ATX must be in conduit, and all
conduit holes (knockouts)on the Control panel shall be used or blocked
tram acoess. (See Diagram36.)
2. Use 12V 4 AH (minimum)Battery.
3. Value of End-of-lineresistor is 1K ohms (‘41~0).
-4. Bntry Delays-cannot exceed 60 seconds for UL Commercial Burglary
tjistings.
5. ~eltir$out cannot be less than 16 minutes for UL Commercial Burglary
LOCATE
687.888.346
WITHIN
-_by
k+l oRzL
NOT I I I
I
I
I
414OATX 6M -
CABINET
N.O. CONTACTS (IF USED)
CLOSING ACROSS THESE
TERMINALS RESULTS
IN A TELEPHONE LINE
TROUBLE CONDITION.
Diagram 43. GRADE A CENTRAL STATION INSTALLATION USING 346 REVERSING RELAY MODULE
INSTALLATION NOTES 1. (‘21) Fire timeout must be disabled (no fire timeout allowed).
2. (1’26) RF transmitter tow battery annunciationmust be enabled.
3. (1’30) 4260 supervisory check-in monitoring interval cannot exceed 12
hours.
4. (1.31) RF transmitter check-in interval cannot exceed 12 hours.
5. (1’49) Audible sounder for transmitter check-in failure must be enabled.
,-.
SECTION XIV
TROUBLESHOOTING
- A. CONSOLES -
SYMPTOM
Console is . Power down completely (AC + battery), disconnect the battery, and
inoperable; power up again (AC only).
erratic display l Check that auxiliary voltage is between 13SVDC-14.OVDC. If not,
disconnect all auxiliary devices, and take another reading. If within the
above range, there is too much current being drawn by the auxiliary
devices. (see the SPECIFICATIONS section tar the current draw of each
device). lf still not within the above range, check incoming power from the
No. 1350 (or 1360) power pack. Voltage should bs between 16-22VDC
with the control hooked up, and 20-24VDC with no load. If below 16VDC,
carefully check the AC supply for a minimum of 110 VAC.
l With all auxiliary devices and battery still disconnected,check the voltage
on the red & black battery leads. It should be 13.65VDC (approx.). lf not,
replace the Control. If it is @ 13.65VDC. the battery may not be at full
charge (allow the battery to charge 4-6 hours before reconnecting the
auxiliary devices) or the battery may be bad, and not able to hold a
charge.
Console displays l Check to make sure there is a zone type response entered in program
“Not Ready” but lield ‘05 for ‘97 (polling loop short). lf no zone response is entered and
no zone is a loop short occurs, the display will only read ‘NOT READY”, without an
explanation.
displayed when
the I’] ready key l Check to detemrine lf a right loop has been enabledfor an RPM in a zone
expanded system and no zone response is assignedto that sensor loop.
is depressed
PTOM ACTlON
Zone 1 in trouble If programmed for fire or burglary using open-circuit sensors, a 13.000
(“CHECK”) ohm EOLR must be used across the zone, at the last device, as
described in the SYSTEM CONFIGURATION:ZONES section.
Zones 2-8 not detecting If using EOLRs, check that program field ‘41=0; if not using EOLRs,
faults when their EOLRs ‘41-l.
are shorted (READY
display stays on)
Zone 9 Is indicating This zone ls for closed circuit, unsupervised use only. Do not use open
a fault (“READY” will circuit devices or an EOLR on this zone.
not appear)
Zone 9 false alarms This zone has a response time of 6-l 0 milliseconds, and should be used
perlodically with ‘Fast response’ devices, such as vibration sensors or glass break
sensors, only. If devices with a response time of greater than 10
milliseconds are used, the zone may false alarm due to contact %ounce”,
if used in areaswhere vibrations may occur.
Zones l-9 not detecting Check program fields 1’16 and 1’19 to make sure the wired zone(s) in
faults (READY light question have not been enabled as RF zones.
stays on)
-Cc. RPMs -
SYMPTOM ACTION
Zones indicating . Check that the DIP switches are set correctiy.
“CHECK” conditions . If only left bops are being used, make sure program fields ‘06, ‘07, ‘08,
1’10,1*11,1’12, and 1’13 are programmedas -0..
. If both left and right loops are being used, make sure program fietds ‘06,
l 07, ‘06, 1’10, 1’11, 1’12, and 1’13 are programmed with “O’s for the
teft loops and ‘1% for the right loops. NOTE: On a 4190WH you cannot
use a right bop unless the left bop is used also.
. Check polling loop voltage at the control as well as at each RPM. There
should be fluctuating 6-1lVDC on the loop. If there is no voltage or
steady voltage, check that the 4152LMB is not shorting against the dialer
board (there should be “fish paper installed in between these boards).
. Check if programmedfor tamper detection in programfield ‘24. lf ‘24 L 0,
the RPM will come up in trouble when its cover is removed (4190WH
only).
. If a 4206 is being used for zones 1O-l7, program field ‘66 must be set for
‘l‘, and the DIP switches should be set as follows: 1,2,3,4, = ON, 5 =
OFF. If any other 4206 configuration is being used, field ‘86 must = -0
and the DIP switches set accordingto the instructions accompanyingthe
4208.
Zones indicating . If using a 419OWH,make sure that the jumpers are set up in accordance
fault conditions with the EOLR being used on the left loop (the right loop never uses an
(“READY” not displayed) EOLR). See the SYSTEM CONFIGURATION:ZONES section for proper
use of these jumpers and EOLRs.
If using a 4208, make sure the zones are set up with the correct EOLRs.
See the SYSTEM CONFIGURATION:ZONES section for 4208 usage.
If using a 4196 right loop, make sure only closed-circuitdevices are used,
and check the program fields ‘06 through ‘08, and 1’10 through 1’13 to
make sure the zones in question are enabled as right loops (‘1”).
“97” appears in This indicatesthat a ‘short. has been detected on the polling loop.
console display Check that polling loop polarity is correct at the control as well as at each
and rapid beeping RPM.
occurs D&on&t the polling loop from the 4152LMB and check for continuity
from the posltive (+) side of the loop to ground. There should be no
continuity to ground. lf there is a ground, the source must be found and
eliminated.
“READY” display not Check program fields 1’19 through 1’25 to make sure that the zones in
going out when zones question are not enabled as RF zones.
are faulted Make sure each zone in question has been programmedfor a response
in fields ‘02~-05 and 1’01-1’05.
Console displays Check program fields ‘06 through ‘08, and 1’10 through 1’13 to make
“NOT READY” but no sure that right loops are enabled for the correct zones. If no right loops
zone is displayed are being used, these fields should = ‘0’.
when [‘I READY key Check program field l 05 to make sure there is a zone type response
is depressed entered for ‘97”. If a polling loop short occurs and no response is
entered for 97. the display would indicate ‘NOT READY” with no
explanation.
ADEMCO’s VISTA XM SERIES TECHNICAL REFERENCE MANUAL
116 TROUBLESHOOTING
- D. WIRELESS -
“88” or “90” appears l The receiver is not receiving any signals from any of the transmitters in
in console display the system. .An“68. is for the 2nd 4280; a “90’ is for the 1st 4280. These
and rapid beeping displays are enabled by assigning a zone response type in program fields
1’06, and 1’09. The recommended response is either zone type 05 or
occurs 07 (see the ZONE TYPE DEFlNlTlONS section. wireless installation.
l Check that the antenna is installed properly and is not shorted to any
metal object, refer to WIRELESS EXPANSION section for details.
. Check that the transmittersare poweredup with fresh 9 voit batteries.
l Check that the house ID’s match betweentransmitters and the 4260.
l Determine if anything is blocking transmission to the 4280 (ex: metal
cabinets or shetves, etc.)
l Remove the 4280%cover and put the system in the test mode, then see
if the transmitters check-in. If not, move the 4260 to another location and
test again.
“89” or “9,”
l The 4280 is not responding to the Control panel. An ‘89’ refers to the
appears in console second 4280 and a 91’ refers to the first 4280.
display and rapid l Check that the 4280’s cover is on and the magnet is in close proximity to
beeping occurs the reed switch.
. Check that the polling bop is attached to the 4280.
l Determinethat the total current draw on the polling loop is not more than ..-.
64mA. See SPECIFICATIONS. If the draw does exceed 64mA, install a
4197 loop extender module as described in the WIRELESS
EXPANSION section, or power the 4280 from auxiliary power, as
described.
l Check that the polling loop length is in agreement with the
recommendedwire gauge. If the length exceeds what is recommended,
install a 4197 loop extender module as described in the WIRELESS
EXPANSION section.
Zones, not pro- * Check program fields l 02 through ‘05, and 1’01 through 1’05’to make
grammed in the sure .allunused zones are 00s.
system, are indicating l Check program fields 1’18 through 1’25 to make sure that all non-RF
“CHECK” conditions zones are 0s.
Zones indicating
“NOT READY” condition, l Put the system in the SNIFFER MODE for at least 2 hours. to see if
but transmitter contact another system in the area is using the same house ID. If so, change this
loop is intact system’s house ID number at the 4280 and at all transmitters.
l Make sure zones In question are selected as RF in fields 1’18-1’25.
.-.
“97” appears in the . Thk indicates that the polling loop has etther a direct short, or a short to
console display ground on the (+) side. Might ako Indicate that the 4280 RF Receiver k
and rapid beeping causing the short (dinned 4280 to vedfy).
occurs . Chedcthatpollingkoppolarltykoonectatthecontlrolpanel,aswllas~
each 4280.
. Check oontinulty from (+) slde of the loop to ground (disconnect the
polling loop from the Control first!) - an open should be read (no
continuity).If a short to ground exists, find and eliminate the short.
a Check voltage across the polling hop at the Control panel as well as at
each 4280 - there should be fbctuatbn between 8-l 1VDC. tf there k no
voltage or steady voltage, check that the 4152LMB k not shorting
against any components on the dialer hoard - there should be Yish
paper installed between these two hoards.
“READY” display not . Check that the house ID’s match between the transmftters and the 4280.
going out when RF . Check that the 4280 is enahkd In program fields 1’26 for the first 4280
zones faulted and 1’27 for the second 4280.
. Check that the zones in question are enabled for RF In program fields
1’18 through 1’25.
l
Check that a zone response k programmedfor the zones in question, tn
fields ‘02 through l 05, and 1’01 through 1’05.
.
Check that the 4280%antennak property installed.
.
Remove any sensors from the transmitters and short across the
transmitterterminals. Then fault the transmttterto see tl the ‘READY fight
goes out. If it does not go out, check the programmingfor that particular
transmitter; if it does go out, check the sensors on that zone.
.
Move the 4280 to another bcatiin for better reception.
Console displays .
Check program field ‘05 to make sure ‘97 has a zone type response
“NOT READY” but no entered. lf a loop short occurs and no response k entered for 97”. the
zone is displayed consolewould display only ‘NOT READY, with no explanation.
when [‘J READY .
A Siknt Panic conditiin may be present. Key the security code + OFF to
key is depressed see it the condition dears.
:-..
- E. COMMUNICATIONS -
SYMP~m!l P-ION
“FC” or “COMM ‘FC’ (413OXM/4137)or ‘COMM FAILURE’ (5130XM/5137)indicates that
FAILURE”, is the communicator has attempted 8 times to send a report to the central
displayed station but did not get kissoff.
Check with the central station to make sure the programmed format is
acceptable to the central station’s receiver. (Check program field ‘46.
PRlMARYTRANSMlSSlONFORMAT).
Check program field ‘49 to see if single message wtth checksum has
been enabled. The central station receiver might not be able to handle
checksum.
Check program field 1’34 to see if split reporting is enabled. If only a
primary central station phone number is being used, field 1’34 must = O!
Check program field ‘31, PABX ACCESS CODE. Enter up to s-digits
only if an outside line must be accessed before the number is dialed or if
“call waiting’ is to be suppressed. The latter feature must be obtained
from the local telephone company. To make sure this field is empty, key
‘31’ to erase this location.
. Check program fietd ‘30 for either TouchTone or rotary dialing. In most
cases, if rotary Is selected dialing will be successful, but if TouchTone is
se&ted, then the line must be a TouchTone line. It is possible that a line
that had permitted TouchTone service previously was now being blocked
from that use by the telephone company because the user was not .->
paying for that service. At installationtime, ft is importantto check with the :’
user to determine if they are paying for TouchTone service. --
. In some cases, the telco switching network may cause a delay
before the acknowledge handshake reaches the communicator. If so.
the communicator may hang up before the acknowledge is received.
If this occurs, enter a ‘1’ in program field ‘45, to increase the
wait tipe for acknowledge.
. If SESCOAlRADlONlCS format is being used, check program field
‘SO. If hexadecimal codes are being sent, enter a ‘0’. If only O-9
is being sent, either a -1” or a “0’ is acceptable. Check with the
central station to verify acceptance of B-F codes.
If 3+1&l LOW SPEED is being used, check programfields ‘53 and l 54
(4+2 selections). There should be ‘0” in both of these fields. Some
central station receivers cannot handle 4+2 reporting.
Check the telephone numbers programmed in fields ‘33 & ‘34.
Liaen to the outgoing call attempts using a handset.
Check the wiring on the Tel00 connector of the 4171XT-XM14171XM.
READ ONLY Pertaining to downloading,an operator wfth this level of access can Only
read informationfrom the database: cannot overwrite any information.
REDUNDANCY Using two systems so that tf one fails the other will carry ofi, as when two
4280 receivers are used, to insure that the transmitters get through to at
least one of the receivers.
RF RECEIVER A wireless receiver, such as the 4280. RF is an abbreviation for Radio
Frequency.
RING/TIP With regard to telephone lines, the ‘rtng” side is the (-), or ‘ground side
of the line, and the Iltip- side is the (+) side of the line. Typical phone line
voftage is 48VDC.
ROUGH-IN RING A metal ring used during new construction and is attached to wall studs to
designate where the VISTA Control or console is going to be mounted,
so that the plasterercan cut an opening in the watl for it when the walls are
installed.
RPM Abbreviationfor Remote Point Module, which is used on the polling loop
for zone expansion. EX: 4190,4208.
RS232 Typical computer serial interface using pins 2, 3, 7, and 20, between
computer and printer, or other peripheral device.
SELF-CONTAINED Refersto when the Control panel and keypad are contained in one unit.
SPDT Abbreviation for Single-Pole, Double-Throw; a 3-terminal switch
consisting of a common terminal, a normally closed side, and a normally
open side; can be used in either open-circuit or closed-circuit
applications; when activated, the closed side opens, and the open side
closes.
SUPERVISED ZONE A zone which uses an end-of-line resistor to differentiate between a short
acrossthe resistor, and an open in the circuit, as in a Fire zone.
UNSUPERVISED ZONE A zone that does not use end-of-line resistors and recognizes only open
circuits, as in burglaryzones.
UPLOADING To send data from the Control panel to the computer.
VOLATILE Refers to RandomAccess Memory (RAM), which loses all data if power is
lost.
ZONE EXPANSION Zones 10 through 84 using the a-wire polling loop with RPMs, 4280
wireless, or both.
WR’=GA’‘m
22 (0.64 mm O.D.) 65O.ft(200 m)
20 (0.61 mm O.D.) 950 ft (290 m)
18 (1.0 mm O.D.) 125Oft(46Om)
16 (1.3 mm O.D.) 165Oft(73Om)
428014280-8 RECEIVER/TRANSPONDER
1. Physical: Width: 4.6” (117 mm)
HeigM: 7.6. (193 mm), 16.5’ (419 mm) with antenna ’
Depth: 2.5” (64 mm)
NOTE: The antenna does not have to be vertically pointed up. Attematiiely,~theheight and width dimensions can
be interchanged it the untt is mounted with the antenna in a horizontalposition.
2. Electrical: Voltage: 7-l 1 Volts (with 1kHz modulationfrom an Ademco polling Loop)or 7-14 VDC
Input Current:. 40mA
SECTION XVII
SUMMARY OF CONNECTIONS
&
PROGRAMMING DEFAULTS
- A. SUMMARY OF CONNECTIONS -
TABLE 9. AUXILIARY DEVICE CURRENT DRAW WORKSHEET
VISTA CURRENT x NUMBER TOTAL
DEVICE DRAW OF UNITS = CURRENT
REMOTE CONSOLES
4137 6OmA
5137 150 mA
KEYSWITCH
4146 2omA
GROUND START
675 5omA
RF RECEIVERS
4280 or 4280-8 40 mA
l If the total current draw exceeds 64 rnA, a 4197 Loop Extendermodule must be used.
’ tf using two 4280s or 42808s you can power one of them from auxiliary power insteadof using a
4197 luop extender module. See Wireless Expansionfor proper connections.
r--------“7
MERNATIVE
‘ZONE1
fN C LOOP)
LO
L-,---,-,,,
-OPEN/CLOSE
.-.
SUbihfARY OF CONNECYIONS 131
33073m3do.
132 SUA~MARY OF CONNECTIONS
DEslGNATERiGHT 10 11 12 13 14 15 16
ZONE USAGE(W-16) ro1PlrolfolfolroJ WI mm
‘07 DESlGNATERla-rr 1716192021222324
ZONE USAGE(17-24) PI PI f0lr01PI WI PI PI mm
l 06 DESIGNATERIGHT 2526272829303132
ZONE USAGE (2532) WI PI KU01tOI VI WI(01Wne)
l 09 ENfRY DEIAY #l [0X2] (30 seamds)
‘10 EXITDEIAYM [0)[3] (45 seoonds)
‘11 ENTRY DEIAY #2 [0][6] (90 seconds)
‘12 EXflDElAY#2 [One] (120 seconds)
‘13 ~~MMUNDER tolt41 (8 -w
‘14 NoTusED
‘15 KEYSWITCHARhd/DlSARM
‘16 wNRRMAnoiuoF
ARMNGDING
‘17 AC POWERLOSS SOUNDING [q (Disabie)
‘18 AC POWERLOSS ALARM PI (No-1
‘19 NOTUSED to1
l 20 NOT USED IO1
‘21 DISABLEFIRETIMEOUT lo1I
-22 NOT USED PI
-23 MULTIPLEALARMS Ill (v=)
‘24 TAMPER DETECTION WI e-w
DISABLE (ZONES 10-64)
25 DURESS REPORTDISABLE p] (Enabie)
(ADEMCOHIGH SPEED)
‘26 NOT USED PI
‘27 TEST REPORTINTERVAL f21 (24 t-w
26 POWERUP IN Fl (VM
PREVIOUS STATE
29 QUICKARM fll m-w
30 TOUCH-TONEOR Fl CToudr-TOW
ROTARY DIAL
l 31 PABX ACCESS CODE
‘32 PRIMARYSUBSCRIBER
ACCT. No.
. -33 PRIMARYPHONENo. No Entry
34 SECONDARYPHONE No. No Entry
35 CS DOWNLOADPHONE No.
36 csiDNo.
37 DOWNLOADCOMMAND Dialer Shutdown enabled
ENABLES System Shutdown enabled
Not Used
Remote Bypass enabled
Remote Disarm enabled
Remote Arm enabled
Upload Programenabled
DownloadPm enabled
-38 INHiBm BYPASSOF [OHO](AJInon-firezones bypassable)
ONE ZONE (1-31)
39 OPEN/CLOSE REPORTlNG [O][O][O][O~O~O~O][O]
(disabled for Users 9-l 6)
ENABLE BY USER CODE
‘40 REPROGRAMor DOWNLOAD [On01(No code reported)
AITEMPT REPORT
‘41 EOLR DISABLE (Zones 2-8) VI (-f-Line Resistor supewisiin not required)
l 42 DfALTONE PAUSE PI (5 -fw
l 43 DIALTONE DETECTION [l] (Diil Tone DetectionEnabled)
‘44 RING DETECTiONCOUNT [O][O] (Ring detection disabled)
‘45 PRlMARYAcKWAfT PI (30 s@=w
‘46 PRIMARYTRANSMISSION IO1 W-=0 h speed)
FORMAT
-47 SECONDARYACK WAlT WI w smm
l 46 SECONDARY PI We- Lfi9~speed)
TRANSMISSION FORMAT
‘49 SINGLE MESSAGE PI (No)
TRANSMfSSlONWfTH
CHECKSUM VERIFICATION
SESCOAIRADIONICS [O] Radiinics with O-9,B-F reporting.
SELECTION ,-.
DUALREPORTING PI (No)
OPEMXOSEREPORTMG 12 3456 78
ENABLEBY USERCODE [l~O~O][O][O~O][O][O]
(diiblsd for Users 2-6)
‘53 4+2 ZONE EXPANDED to1 (Not-leded)
FORMATSELECTION
‘54 4+2 ZONE STANDARD
FORMATSELECTION
‘55 AlAfW REPORT
36 RESTOREREPORT
57 BYPASS REPORT
38 TROUBLE REPORT
‘59 OPENCLOSE REPORT
LOW BATTERY,AC LOSS
AND TEST REPORT
‘61 CHANNELASSIGNED
TO EACH ZONE
0 ‘62 CHANNELASSIGNED Z9 [Ol[ol Zeroes for zones 9-16 (no code repotlad)
TO EACH ZONE (CONT’D) ZlO fwJ1
Zll _ _- _
101~01
212 f01f01
213 m01
214 tol~ol
Z15 rao1
Zl6 [OHO]
‘63 CHANNELASSIGNED 217 [OIO] Zeroesfor zones 17-24 (no code reported)
TO EACH ZONE (CONT’D) Zl8 PIP1
z19 fWO1
220 101101
‘64 CHANNUS ASSIGNED 1 [OIO] Z25 All zeroesin 8 bcatiins (same as Addressl 61)
TO ZONES 25-27, DURESS 2 fW1 226
AND VARIOUSKEYPAD 3 _101101
__ Z27
PANICS 4 [OHO] Durew
5 [O][O]Short on Wiring to Zone Expander(displays97)
6 roll01
- -. - 18 Panic (dffiphys 95)
l
,f-=.
74 4+2 EXPANDEDFORMAT 1 [OIO] AL Zeroes for zones 17-24 (no codes reported)
ZONES 17-24EVENT 2 l-R
f01101
Di(=(l@efw BY
3 f01101
4 [OHO]AL RE
5 [O][O]TR RE
6 [0x0] BY RE
75 1 ron01AL
2 loll01TR
. I.-.
3 tOI BY
4 [OHO]AL RE panics and for zone expander
5 [OHO]TR RE witi~~i~~ (no
6 [Ogo)BY RE
76 “MAT
(2nd dill)
[O][O]3 8 # Panic
[O][O] & # Panic
l
NOT USED
ZONE EXPANDER TYPE
SELECTION
97 ENTRY WARNING (continuousbeeps)
-88 BURGLARYAfARM (no 0
COMMUNlCATfON DELAY
-89 NOTUSED
SECONDARY SUBSCRIBER
ACCT. No.
NOTE: The following fields are accessed by inttfalfykeyfng ‘94 while in the programmingmode. Afthough
numbered from 00 to 49, they are not the same fiekfs as 00 to 49 fisted previously, and are identifiedin this manual
as fiefds 1’00 to 1’49 where the leading -1. fs not keyed.
,-.
3334353637383940
1’10 DESIGNATERIGHT PI 101PI PI 101PI 101PI
ZONE USAGE (33-40)
4142434445464746
1'11 DESIGNATERIGHT PI PI PI PI 101PI IO1to1
ZONE USAGE (4148)
4950515253545556
1’12 DESIGNATERIGHT uI101PI to1PI PI to1M
ZONE USAGE (49-56)
5756596061 626364
1’13 DESIGNATERIGHT PI PI 101WIPI vu PI 101
ZONE USAGE (57-64)
1’34 COMMUNICATORSPLIT
REPORT SELECTION
1’35 CHANNELASSIGNEDTO 10m z28
E%H ZONE (CONl’D) [OHO]229 Zeroesfor zones 26-32
101101
z30 (no- repofled)
Pm 231
MI01232
136 CHANNEL
ASSIGNEDTO
EACHZONE [OI[O]235 Zeroes for zones 33-40
(-1 IOlPI236 (no-f wof’W
&P~ g
PIPI 239
[OH01240
[O]IO]241
[OHO]242
[O][O]243 Zemes for zones 41-46
p\~~ (no code mfled)
Imolz~
IOHOJ249
I=0
1Z51 Zeroes for zones 49-56
1252 (no code reported)
CHANNELASSIGNED zs vJlr41
TO EACH ZONE (CONT’D) ZlO [Ol[O]
Zll [ON01
a2 101101
213 101101
214 101101
z15 [ONO]
Z16 101101
‘84 CHANNELSASSIGNED
TO ZONES 25-27, DURESS
AND VARIOUSKEYPAD
E227
PANICS Duress
Short on Wiring to Zone Expander (displays 97)
l.&*Panic(displays95)
38#Panic(displays96)
l 8 # Panic (displays99)
‘65 ALARM REPORTINGCODES
ASSIGNEDTO EACH
CHANNEL
CHANNELASSIGNED ZQ19lIQl
TO EACH ZONE (CONTD) z10 m91
Zll [O~O)
212 101P1
Zf3 101~01
214 101t01
Z15 wto1
2% 101101
ADEMCO’x VISTA XM SEBIBS TBCHNKAL RRFERBNCB MANUN.
146 SVddMARY OF CONNECTIONS.
VquLE
‘64 CHANNUS ASSIGNED 1 KJlM 225
TO ZONES 25-27, DURESS 2 IWO1226
AND VARIOUSKEYPAD 3 1w1 227
PANICS 4 [inO) Duress
5 [O)[O)Short on Wiring to Zone Expander (displays 97)
6 [O)[O)18 Panic (displays95)
l
5155 5555 7
5515 5555 7
55515555 7
ASSIGNR-E
TYPE FOR ZONES9-16
f :
Zl
‘04 ASSIGN RESPONSE
lYPE FORZONES17-24
E!E?l
INTFOLL
INT,FoLL
PERIM
PERIM
PERIM
PERIM
INTDEL
TRBL,DAY/ALRM,NIGHT
TRBL,DAY/ALRM,NIGHT
TRBL,DAY/ALFiM,NIGHT
TRBL,DAY/ALRM,NIGHT
PERIM
PERIM
PERIM
PERlM
DURESS
LOOPSHORT
2; ::
‘&# 1E
NON-ALARM CODES
OPEN
POWERUP
CLOSE
AC LOSS
LOW BAIT
AC RESTORE
LOW BAlT-RESTR
CANCEL
E&R
:--.
WARNING
THE LlYtTATlONS OF THls ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other
emergency. Any alarm system, whether commercial or residential. is subject to compromise or failure to warn for a number of
reasons. For example:
l Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or
disconnect an alarm warning device.
0 Intrusion detectors (e.g.. passive infrared detectors). smoke detectors. and many other sensing devices will not work without
power. Battery operated devices will not work without batter% with dead batteries. or if the batteries are not put in properly.
Devices powered solefy by AC will not work if their AC power supply is cut off for any reason, however briefly.
l Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the
signal path has been recently checked during a weekly test. blockage can occur if a metal object is moved into the path.
l A user may not be able to reach a panic or emergency button quickly enough.
0 While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or
provide early warning for a variety of reasons in as many as 95% of all fires, according to data published by the Federal
Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work
are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that
Stan where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors.
Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example,
may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense
every kind of fire every time. In general. detectors may not always warn about fires Caused by carelessness and safety hazards
like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits,
children playing with matches, or arson. Depending on the nature of the fire and/or the location of the smoke detectors. the
detector, even ff ft operates as antdpated, may not provide sufficient warning to allow all occupants to escape in time to
Prevent injury or death.
l Passive infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation
manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and
intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that
takes place behind walls, ceilings, floors. closed doors, glass partitions, glass doors, or windows. Mechanical tampering.
masking, painting or spraying of any material on the mirrors, windows or any pan of the optical system can reduce their
detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the
protected area approaches the temperature range of 90’ to 150°F. the detection performance can decrease.
l Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers who are located on the other
side of a closed or partly open doors. If warning devices sound on a dierent level of the residence from the bedrooms, then
they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the
alarm is muffled by noise from a stereo, radio, air conditioner or other appliances, or by passing traffic. Finally. alarm warning
devices, however bud, may not warn hearing-impaired people or waken deep sleepers.
l Telephone lines needed to transmit alarm signats from a premises to a central monitoring station may be out of service or
temporarily out of SenriCe. Telephone lines are also subject 10 compromise by sophisticated intruders.
l Ev&n if the system responds to the emergency as intended. however. occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system. authorities may not respond appropriately.
a This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as
long as 10 years, the electronic components could fail at any time.
The most common cause of an alam, system not functioning when an intrusion or fire occurs is inadequate maintenance. This
alarm system should be tested weekly to make sure all sensors are working property.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance.
Homeowners, property owners and renters should continue to act prudently in protectrng themselves and continue to insure their
lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones
to learn about these developments.
ADEMCO
LIMITED WARRANTY
Alarm hViCe Manufacturing Company. a Division of Prltway Corporation. and its divisions. subsidiaries and affiliates (“Seller”). 166 Erfeen Way.
SyOSSet.New York 11791. warrants its products to be in conformance with its own plans and specifrcatrons and lo be free from defects In materials
and workmanship under normal use and service for 16 months from the dale stamp control on the product or. for products not havrng an Ademco
date Stamp. IOr 12 months from date of original purchase unless the rnstallation instruclrons or catalog sets forth a shorter period. In which case the
shorter period shall apply. Sellers obltgalion shall be kmited to repainng or replacrng. al 11soption. free of charge for malenals or labor. any part which
iS proved not In compliance with Seller’s specificatrons or proves detectwe in materials or workmanship under normal use and service. Seller shall
have n0 obligatron under this Limited Warranty or otherwise if the product is altered or improperly reparred or serviced by anyone Otherthan Ademco
factory sernce. For warranty service. return product transportation prepaid.lo Ademco Factory Service. 165 Eileen Way. Syosset. NewYork 11791.
THERE ARE NO WARRANTIES. EXPRESSOR IMPLIED.OF MERCHANTABILITY. OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE.
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. EXPRESS OR IMPLIED. OR UPON ANY
OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER’S OWN NEGLIGENCE OR FAULT.
Seller does not represent that its product may not be compromised or circumvented: that the producl will prevent any personal Injury or properly loss
by burglary. robbery. IIre or otherwise; of that the product will in all cases provide adequate warnmg or protection. Buyer understands that a properly
installed and maintained alarm may only reduce the risk of a burglary. robbery or fire without warning. but it is not insurance or a guarantee that such
will not occur or that there will be no personal intury or properly loss as a result. CONSEQUENTLY. SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY. PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However. if Seller
is held liable. whether directly or rndirectfy. tor any loss or damage arising under this Limited Warranty or otherwrse. regardfess of cause or ongin.
Seller’s maximum liability shall not rn any case exceed the purchase pnce of the product. which shall be the complete and exclusve remedy agarnst
Seller.
This warranty replaces any previous warranlres and islhe onty warranty made by Selter on this product. No increase or alteration. written or verbal. of
the obligation of this Lrmited Warranty is authorized.
a0 2u
231 236 2u
238 247
240 249
4+2 EXPANDED
FORMAT NON- ‘194 ZNS 49 - 56 ‘105 MS 67 - 64 ,196 ASSIGN RESP.
ALARM CODES 249 TYPE 2ND 4269
(Emer 01 - 15; OPEN REPORT
00.mmde 250
W=Nl) LOW SATT REPORT
251
LOW SATT RESTORE RPT
252
TEST REPORT
253
4+2 EXPANDED
FORMAT NON
ALARM CODES -R-up REPoRT
%ddi9itisdsoowQDnddi~tWpoorpm
(CONT’D) remper-(~W
(Elnw 01 - 15:
oo-nocode AC LOSS REPORT
fwwQn9) ‘196 NOT USED 107 NOT USED
AC RESTORE REPORT
‘109 ASSIGN RESP. TYPE 1ST & 2ND 4266
CANCEL REPORT ~ND~~~ONOTRESPJE~DWNNTOPANEL
1ST4299NOTRECENffiXWTTERSY;W.S
264
SELECTION OF WIRELESS FOR: 11l YES.0 - W
‘116 ZN 1 - 6 zND426oNo
266
XMTR CHECK-IN
iiiiipipl FAULT
-119 P(S-16
8 10 11 12 13 lb 15 16 ‘143 CHANNEL 269 ZND
I . 4
4280 NOT FUNCTION4L
llll1I II ASSlGNED
TO RF RCVR I-H
290 1ST 4280 NO XMTR CHECK-IN FAULT
17 16 19 20 21 22 23 24
FAULTS n, 1ST 4260 NOT FUNCTIONAL
‘120 P(l7-24
25
lIlllll~
26 27 26 29 30 31 32
tn
‘144 WIRELESS KEYPAD TAMPER
l 12l m26-32
I I I I I I I 1 lDzy E.ABLE cl
333495363738 39 40
‘145 iNAiL; CONSOLE ANNUN
‘122 zN33-40
lllllll] ,lfJ:;Nf F DELAY cl
41 42 U 44 45 46 47 46
l 123 zN41.48 l 146 AUX. ‘OhPUT FUNCTION
49
IIIIIIII
50 51 52 53 54 55 56
ENABLE
0 I CND START. 11 OPtCL TRGR.
Cl
2.wNsaEsotnas
01-15 cl X2wuRS
‘132 sD$Fsy Hs. CONTACT RPT FMT 5
‘133 IfDhoi/$OTARY BACKUP
I m II
734 COh’lM SPLI? REPORTING
b NO. 1 -ALARMS PRWUTHEAS SEC. 2 c
I OPICL. TST SEC. OTHERS PRI
231 244
232 215
238 246
43l
239 247
216 246
XWPR am
m
4130XM/4140XM/5130XM PROGRAMMING FORM
INSTALLER CODE
W=RW
MASTER CODE -0l
(WTER &O) ZONES
RESPONSE TYPE l 02
(ENTER -10)
‘23cl
zoN!Es
009wnmdzmo
ol-6lEn
QP-6682
039Prinm
wr-
mmrli
1 II ! II I-JDISABLETAMPER
12 DETECTIONIN
‘24
cl
049hlawfo9mu
o!i-T~byd6y/
-byfw
06124hShm
07124HrAdible
05124hAuxiby
08-F&@
10~hmioroslay
O-norsport: -12hn.;2~24hrs.3~165hrs
/* 358 ‘58
POWER-UP IN ‘28
(0 f’ ,;2
,,- .13- *.14
,, ..15
r,-,fi~~~~mSTATE cl
DESIGNATE RIGHT ‘66
lm uo~5zoe
4181,4,?.4104A21j
413s
uu&
17 15
--------
10 20 21 22 23 24
II II Juu
a&
I rvr.o-NO
iii 928
un
ndbtWlbOplpoplWWHUbd
PlRan4188; l brri@htboopan
’ 31 32 TOUCH-TONE DIAL ‘36
El
41ooHM ald aticy hop on 3cluno I-Voa.OrROlARY
4105.
ENTRY DELAY #I
xlssaa(oo-15) m PABX CODE 9’ I
m
00.os:B-F(ll-15)
EXIT DELAY #I PRIM SUBSCRIBER #
x15Boa(00-15)
m
00-OQ;B-F(11-15)
ENTRY DELAY #2 PRIMARY PHONE t ‘33
X15ssa(oO-15)
EXlTDELAY#2
Xl5ua(OO-15) m O-OE
ALARM SOUNDER
TIME DURATION m SEC PHONE # -34
x 2 tins.
NOT USED
(01-15)
-14 cl0 o-Q E
MJ8TBEo. E DOWNLOAD5
l 15
q
EEemmm
CONFIRMATION OF l 16 cl
fM:Nt ZNG ENABLE -36
!ii?&%-F(lO-15)
AC L&i TRBL SOUND ‘17
El
l-Ya.0.No
AC PWR LOSS ALARM ‘18 DOWNLOADING 57
1 IYeB.OIrn El
COMMANDS IDLU~RSIW~DOWN
CDNTROL ALARM ‘19 ALLOWED
cl 2SYsTEusHITDowN
SOUNDER DISABLE 1 -Y8S.Olm
l~voa.o~No uako8mdiinnabr4140
6RWDTEARM
7uPLmoPRaRAM
8 -D PRoGRaM
CHANNEL ASSIGNED ‘61 lEmn O1- 15:00 -
PRJORKY ZONE no mdrm8mm)
01-31(00w6nzonn~
w-1
OPENICLOSE
‘62
REPORT ENABLE
1rvr.o-M
PROGRAM TAMPER RPT l 40
(lrfdigiqOl-15(00-nonpoq
USE EOLRs ON
ZONES 2-6
1 - NC. loops. 0 - EDLR rupmriatrn
‘64
DIAL TONE PAUSE ‘42
0-5aws..l-ll66cs.2-3486c~ cl ZONE 25 26 27 DURESS SHORT 16. 361 l 68
DIAL TONE DETECT
1 - Yes. 0 I No; JUST PAUSE
RING DETECT COUNT
‘42
l 44
cl mmmmmmmm ‘66
ALARM CODES FOR ‘66
cl EACH CHANNEL
00rnL?lingllolut01-14tuIingonJnm0t1-14;
15 when talaphms l rwanng m6dtii is wnnocad to (Enter 01 -15: CHl w9
mssmnephomLi* 00-flOod0W!OMQ)
CHlO
cl42
PRIM ACK WAIT ‘45 cH3 CHll
0-30saa.:1~60saa. cl
Cn12
PRIM XMIT FORMAT Cl-U
O-ADEMCOLQ 1 -SE scildi? cl
2 - ADEMCD HI SPEED cl45 CH13
0-3oSECS;l.6OSECS. cl
cH7 CHl5
SEC XMIT FORMAT ‘46
0 - ADEMCO Lo: 1 I SESCtRAD cl
a46
2 - ADEMW HI SPEED
CHECKSUM VERIFY ~49 n Liz
1 -Yas.olm NON-ALARM CODES %7 ‘88
SESCOAIRAMONICS ‘60 (Enter 01 - 1%
SELECTlON OO-flOOOdO~rparmg)
O.R~OIW¶WW’O-RB.F~;
-TfcITlnm
RESTORE REPORT
o-sml4md:1-Gpmdod
‘56
cl 4+2 EXPANDED
FORMAT ZONES
‘72
1stDIGIT
76
2fmDlGlT
BYPASS REPORT
0-an6ue1-Exp8ndd
‘67
cl l-8 REPORTS ALRM 21
TROUBLE REPORT
O-BtwIuctl-Expmrhd
‘58
cl (Elmlo
001mode
-1
- 15;
TRBL 22
OPEt@ClOSE
0=Bm6ad;1r6xpM%d
REPORT l 69
Cl BYPABS
23
24
LOW BAT; AC LOSS
REPORT
‘60
Cl MRM RESTR
TRBLRESTR Ls
09Bma&1~6xpudad
26
BYPASS RESTR
27
26