Professional Documents
Culture Documents
GO
LO FOR COLUMN BASE PLATE Rev :
1 Design Loads
Load case Max vertical Min vertical Max moment Min moment
Design Data
2 Base Plate
Length of plate Lp = 400 mm C/C of bolt
Width of plate Wp = 300 mm
Thickness Tp = 32 mm f
Thk of top Plate (Ttp) = 32 mm
Length of top Plate (Ltp) = 350 mm Lc Dc
width of top plate Wtp = 300 mm
Catilever length Lc = 50 mm Ttp
Material Specifications
Grade of concrete = M30
Comp Strength Fck = 30 N/mm2
Bearing strength 0.45*Fck = 7.5 N/mm2
Ec = 28576.791 N/mm2
permissible comp stress = 8.4 N/mm2
Base plate
Grade of steel = E 250
Yield Strength = 250 N/mm2
Min Specified Tensile Stress = 410 N/mm2
Permissible Bending Stress = 165 N/mm2
Es = 200000 N/mm2
Bolts
Grade of bolt = 4.6
Yield Strength = 240 N/mm2
Tensile Stress = 400 N/mm2
WELDS
Welding Electrodes = Ex 41xx IS 814
Permissible Stress = 410 N/mm 2
Calculation of anchore bolt force & base pressur [Ref. design of welded structure by omer W. Blodgett]
Depending on nature of P & value of e there will be foure cases as defined below
Case-1: e <= D/6 and P is +ve Case-3: e <= f and P is -ve
sc,max = P/(BxD)+6Mz/(BxD ) 2
sc,max = 0
Pt = 0.00 Pt = P/2(1+e/f)
Case-2: e > D/6 and P is +ve Case-4: e > f and P is -ve
sc,max = (PtxY)/[Asxnx(D/2-Y+f)] sc,max = (PtxY)/[Asxnx(D/2-Y+f)]
Pt = -P[D/2-Y/3-e)/(D/2-Y/3+f)] Pt = -P[D/2-Y/3-e)/(D/2-Y/3+f)]
Y +k1Y +k2Y+k3 = 0
3 2
Y3+k1Y2+k2Y+k3 = 0
Where Where
As = Total area of bolts on tension side k1 = 3(e-D/2)
= AbxNr k2 = [(6nAs)/B]x(f+e)
= 1628 mm 2
k3 = -k2(D/2+f)
n = Modular ratio As & n are same as defined in Case-2
= Es/Ec = 7.00
Y = Distance between max. to zero base pressure
k1 = 3(e-D/2)
k2 = [(6nAs)/B]x(f+e)
k3 = -k2(D/2+f)
4 Design of plates
Plate 1 Base plate Stiff Plate 2 Panel 1
Max compression =
6.02 N/mm 2
size is O.K
Max Cantilever moment due to compression
Max cantilever Lc = 50 mm
Cantilever moment = 7521 Nmm per mm width
Stiff plate 3
Panel 1 Lc
no of stiifner plate 4 = 0 Panel 2
no of stiifner plate 3 = 1 Stiff Plate 1 Panel 3
Stiff Plate 4
2 side supported panel Panel 2
no of stiff plate 1 = 1 nos a1
a = 50 mm a1 = 146 mm
b = 150 mm d1 = 138 mm d1
a/b = 0.33 a/d = 1.06
β = 0.057 coefficient = 0.11
Moment = 7676 Nmm per mm width
Wx = 0.2963 Wx = 1.38 kN
Wy Wy
= 20 mm < 32 mm
= 86.861 mm
5 Design of Boltss
6 Design of weld
Built up 126.9 550 200 16 20 161.6 73893.47 2684.07 2687.04 268.41 3160.4 432.64 21.38 4.1 510.00 100.00 5.00 31.88 Plastic 510
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 k1 k2 k3
1 -633 125367 -94025585
.
x 659.20
CommandButton1
MUKHANOV's-TABLE
Case-1 For 4 side Supported Portion (As per Mukhanov's Text Book)
b
Plate
Supporte a/b 1.0 1.1 1.2 1.3 1.4
d on all
a1 0.048 0.055 0.063 0.069 0.075
Four
Sides a2 0.048 0.049 0.05 0.05 0.05
Case-2 For 3 side Supported Portion (As per Mukhanov's Text Book)
a1
d1
Plate
Supported a1/d1 0.5 0.6 0.7 0.8 0.9
on Three
Sides a3 0.06 0.074 0.088 0.097 0.107
0.5 0.06
0.6 0.074
0.7 0.088
0.8 0.097
0.9 0.107
1.0 0.112
1.1 0.116
1.2 0.12
1.3 0.123
1.4 0.126
1.5 0.127
1.6 0.128
1.7 0.129
1.8 0.13
1.9 0.131
2.0 0.132
0
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9
0.112 0.116 0.120 0.123 0.126 0.127 0.128 0.129 0.129 0.131
2.0 >2.0
0.132 0.133