The document provides operational performance test results for three excavator models: R300LC-9S, R220LC-9S, and R210LC-7. It includes evaluation of engine speed, travel speed, track revolution speed, travel deviation, swing speed, swing function drift, swing bearing play, hydraulic cylinder cycle times, dig function drift, control lever operation force, and control lever stroke. Standards and maximum allowables are provided for each test category.
The document provides operational performance test results for three excavator models: R300LC-9S, R220LC-9S, and R210LC-7. It includes evaluation of engine speed, travel speed, track revolution speed, travel deviation, swing speed, swing function drift, swing bearing play, hydraulic cylinder cycle times, dig function drift, control lever operation force, and control lever stroke. Standards and maximum allowables are provided for each test category.
The document provides operational performance test results for three excavator models: R300LC-9S, R220LC-9S, and R210LC-7. It includes evaluation of engine speed, travel speed, track revolution speed, travel deviation, swing speed, swing function drift, swing bearing play, hydraulic cylinder cycle times, dig function drift, control lever operation force, and control lever stroke. Standards and maximum allowables are provided for each test category.
(1)Engine Speed Evaluation ( Cluster Type 1) Unit : rpm
Model Engine Speed Standard Remarks
Start idle 1000 ± 100
P mode 2100 ± 50 S mode 2000 ± 50 R300LC-9S E mode 1900 ± 50 Auto decel 1150 ± 100 One touch decel 1000 ± 100
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable
1 Speed 22.5 ± 2.0 29.9
R300LC-9S 2 Speed 13.6 ± 1.0 18.7
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable
1 Speed 35 ± 2.0 43.7
R300LC-9S 2 Speed 21.1 ± 2.0 26.4
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks
R300LC-9S 200 below 240
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power mode switch Standard Maximum allowable
P mode (Cluster type 1)
R300LC-9S 16.8 ± 1.5 21 M mode (Cluster type 2)
(6)Swing Function Drift Check Unit : Degree
Model Power mode switch Standard Maximum allowable
P mode (Cluster type 1)
R300LC-9S 90 below 157.5 M mode (Cluster type 2)
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks
R300LC-9S 0.5 ~ 1.5 3
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 4.0 ± 0.4 5
Boom lower 2.5 ± 0.4 3.2 R300LC-9S Arm in Regen ON 3.3± 0.4 4.3 Arm out 3.2 ± 0.3 4 Bucket load 2.4 ± 0.4 2.9 Bucket dump 2.4± 0.3 2.8
(9)Dig Function Drift Check Unit : mm/ 5 min
Model Drift to be measured Standard Maximum allowable Boom cylinder 10 below 20 R300LC-9S Arm cylinder 10 below 20 Bucket cylinder 40 below 50
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.6 or below 2
Arm Lever 1.6 or below 2 R300LC-9S Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 102 ± 10 128
Arm Lever 102 ± 10 128 R300LC-9S Bucket Lever 90 ± 10 113 Swing Lever 90 ± 10 113 Travel Lever 142 ± 10 178 Operational Performance Test (R200LC-9S)
(1)Engine Speed Evaluation ( Cluster Type 1) Unit : rpm
Model Engine Speed Standard Remarks
Start idle 850 ± 100
P (M)mode 2100 ± 50
S (H) mode 2000 ± 50
R220LC-9S E (S) mode 1900 ± 50
Auto decel 1150 ± 100
One touch decel 1000 ± 100
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 18.9 ± 2.0 23.6 R220LC-9S 2 Speed 13.1 ± 1.0 16.4
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable
1 Speed 28.8 ± 2.0 35.4
R220LC-9S 2 Speed 19.2 ± 2.0 23.4
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks
R220LC-9S 200 below 240
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power mode switch Standard Maximum allowable P mode (Cluster type 1) R220LC-9S 15.8 ± 1.5 19 R220LC-9S 15.8 ± 1.5 19 M mode (Cluster type 2)
(6)Swing Function Drift Check Unit : Degree
Model Power mode switch Standard Maximum allowable
P mode (Cluster type 1)
R220LC-9S 90 below 128.7 M mode (Cluster type 2)
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks
R220LC-9S 0.5 ~ 1.5 3
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 3.5 ± 0.4 4.1
Boom lower 2.5 ± 0.4 3.2 Arm in Regen ON 3.2± 0.4 3.8 Cluster type 1 Regen OFF 3.7 ± 0.4 4.5 R220LC-9S Arm in (Cluster type 2) 3.7 ± 0.4 4.5 Arm out 3.0 ± 0.3 3.8 Bucket in 2.5 ± 0.4 3.3 Bucket out 2.3 ± 0.3 2.9
(9)Dig Function Drift Check Unit : mm/ 5 min
Model Drift to be measured Standard Maximum allowable
Boom cylinder 10 below 20
R220LC-9S Arm cylinder 10 below 20 Bucket cylinder 40 below 60 (10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.7 or below 2
Arm Lever 1.7 or below 2 R220LC-9S Bucket Lever 1.4 or below 2 Swing Lever 1.4 or below 2 Travel Lever 2.1 or below 3.15
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 112 ± 10 128
Arm Lever 112 ± 10 128 R220LC-9S Bucket Lever 90 ± 10 113 Swing Lever 90 ± 10 113 Travel Lever 139 ± 10 178 Operational Performance Test (R210LC-7) (1)Engine Speed Evaluation Unit : rpm
Model Engine Speed Standard Remarks
Start idle 1050 ± 100
M mode 2150 ± 50 R210LC-7 H mode 2050 ± 50 S mode 1950 ± 50 Auto decel 1200 ± 100 One touch decel 1050 ± 100
Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R210LC-7 R210LC-7 Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R210LC-7 Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178 Operational Performance Test (R290LC-7A) (1)Engine Speed Evaluation Unit : rpm Model Engine Speed Standard Remarks Start idle 800 ± 100 M mode 1850 ± 50 R290LC-7A H mode 1850 ± 50 S mode 1750 ± 50 Auto decel 1050 ± 50 One touch decel 800 ± 50
Model Kind of lever Standard Maximum allowable Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R290LC-7A Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R290LC-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178 Operational Performance Test (R35Z-7) (1)Engine Speed Evaluation Unit : t/rpm Model Engine Speed Standard Remarks Low idle 1100 ± 100 R35Z-7 High mode 2350 ± 50
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 28.8 ± 2.0 36 R35Z-7 2 Speed 16.0 ± 1.0 20
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 19.3 ± 2.0 24 R35Z-7 2 Speed 10.6 ± 2.0 13.2
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R35Z-7 200 below 240
(5)Swing Speed Evaluation Unit : Seconds / 2 revolutions
Model Standard Maximum allowable Remark R35Z-7 12.6 ± 1 15.8 (6)Swing Function Drift Check Unit : Degree
Model Standard Maximum allowable Remarks
R35Z-7 40 below 50
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks
R35Z-7 0.5 ~ 1.2 2.4
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Drift to be measured Standard Maximum allowable Boom cylinder 10 below 20 R35Z-7 Arm cylinder 20 below 30 Bucket cylinder 20 below 30
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable Boom Lever 1.4 or below 1.9 Arm Lever 1.4 or below 1.9 R35Z-7 Bucket Lever 1.4 or below 1.9 Swing Lever 1.4 or below 1.9 Travel Lever 2.0 or below 2.5
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R35Z-7 Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 86 ± 10 105 Operational Performance Test (R35Z-7A) (1)Engine Speed Evaluation Unit : t/rpm Model Engine Speed Standard Remark Low idle 1100 ± 100 R35Z-7A High mode 2350 ± 50
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 28.8 ± 2.0 36 R35Z-7A 2 Speed 16.0 ± 1.0 20
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 19.3 ± 2.0 24 R35Z-7A 2 Speed 10.6 ± 2.0 13.2
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R35Z-7A 200 below 240
(5)Swing Speed Evaluation Unit : Seconds / 2 revolutions
Model Standard Maximum allowable Remark R35Z-7A 12.6 ± 1 15.8 (6)Swing Function Drift Check Unit : Degree Model Standard Maximum allowable Remarks R35Z-7A 40 below 50
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R35Z-7A 0.5 ~ 1.2 2.4
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable Boom raise 2.4 ± 0.4 3 Boom lower 2.1 ± 0.4 2.7 Arm in 2.9 ± 0.4 3.5 Arm out 2.3 ± 0.4 2.9 Bucket load 3.2 ± 0.4 3.9 R35Z-7A Bucket dump 2.1 ± 0.4 2.7 Boom swing(LH) 5.3 ± 0.4 6.4 Boom swing(RH) 4.0 ± 0.4 4.8 Dozer up(Raise) 1.3 ± 0.3 1.6 Dozer down(lower) 1.3 ± 0.3 1.6
(9)Dig Function Drift Check Unit : mm/ 5 min
Model Drift to be measured Standard Maximum allowable Boom cylinder 10 below 20 R35Z-7A Arm cylinder 20 below 30 Bucket cylinder 20 below 30 (10)Control Lever Operation Force Unit : kgf Model Kind of lever Standard Maximum allowable Boom Lever 1.4 or below 1.9 Arm Lever 1.4 or below 1.9 R35Z-7A Bucket Lever 1.4 or below 1.9 Swing Lever 1.4 or below 1.9 Travel Lever 2.0 or below 2.5
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R35Z-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 86 ± 10 105 Operational Performance Test (R500LC-7A) (1)Engine Speed Evaluation Unit : rpm
Model Engine Speed Standard Remarks
Start idle 800 ± 100
M mode 1950 ± 50 H mode 1850 ± 50 R500LC-7A S mode 1750 ± 50 Auto decel 1000 ± 100 One touch decel 800 ± 100
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 21.8 ± 2.0 27.3 R500LC-7A 2 Speed 13.8 ± 1.0 17.3
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 38.5 ± 2.0 48 R500LC-7A 2 Speed 24.0 ± 2.0 30
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R500LC-7A 200 below 250 (5)Swing Speed Evaluation Unit : Seconds / 3 revolutions Model Power selector switch Standard Maximum allowable R500LC-7A H mode 18 ± 1.5 22.5
(6)Swing Function Drift Check Unit : Degree
Model Mode select switch Standard Maximum allowable R500LC-7A H mode 90 below 112.5
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R500LC-7A 0.5 ~ 1.5 3
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable Boom raise 4.4 ± 0.3 5.2 Boom lower 3.8 ± 0.4 4.5 Arm in 4.0 ± 0.4 4.8 R500LC-7A Arm out 3.5 ± 0.3 4.3 Bucket load 3.0 ± 0.4 3.6 Bucket dump 3.1 ± 0.3 3.7
(9)Dig Function Drift Check Unit : mm/ 5 min
Model Drift to be measured Standard Maximum allowable Boom cylinder 10 below 20 R500LC-7A Arm cylinder 10 below 20 Bucket cylinder 40 below 50 (10)Control Lever Operation Force Unit : kgf Model Kind of lever Standard Maximum allowable Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R500LC-7A Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R500LC-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178 Engine Speed Evaluation (1)Engine Speed Evaluation ( Cluster Type 1) Unit : rpm
Model Engine Speed Standard Remarks
Start idle 1000 ± 100
P mode 2100 ± 50 R300LC-9S S mode 2000 ± 50 E mode 1900 ± 50 Auto decel 1150 ± 100 One touch decel 1000 ± 100
(1)Engine Speed Evaluation ( Cluster Type 1) Unit : rpm
Model Engine Speed Standard Remarks
Start idle 850 ± 100
P (M)mode 2100 ± 50 R220LC-9S S (H) mode 2000 ± 50 E (S) mode 1900 ± 50 Auto decel 1150 ± 100 One touch decel 1000 ± 100
(1)Engine Speed Evaluation Unit : rpm
Model Engine Speed Standard Remarks Start idle 1050 ± 100 M mode 2150 ± 50 H mode 2050 ± 50 R210LC-7 S mode 1950 ± 50 Auto decel 1200 ± 100 One touch decel 1050 ± 100
(1)Engine Speed Evaluation Unit : rpm
Model Engine Speed Standard Remarks Start idle 800 ± 100 M mode 1850 ± 50 R290LC-7A H mode 1850 ± 50 S mode 1750 ± 50 Auto decel 1050 ± 50 One touch decel 800 ± 50
(1)Engine Speed Evaluation Unit : t/rpm
Model Engine Speed Standard Remarks Low idle 1100 ± 100 R35Z-7 High mode 2350 ± 50
(1)Engine Speed Evaluation Unit : t/rpm
Model Engine Speed Standard Remark Low idle 1100 ± 100 R35Z-7A High mode 2350 ± 50
(1)Engine Speed Evaluation Unit : rpm
Model Engine Speed Standard Remarks Start idle 800 ± 100 M mode 1950 ± 50 R500LC-7A H mode 1850 ± 50 S mode 1750 ± 50 Auto decel 1000 ± 100 One touch decel 800 ± 100 Travel Speed Evaluation (2)Travel Speed Evaluation Unit : Seconds / 20 m Model Travel Speed Standard Maximum allowable 1 Speed 22.5 ± 2.0 29.9 R300LC-9S 2 Speed 13.6 ± 1.0 18.7
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 18.9 ± 2.0 23.6 R220LC-9S 2 Speed 13.1 ± 1.0 16.4
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 21.2 ± 2.0 26.5 R210LC-7 2 Speed 13.6 ± 1.0 17
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 23.2 ± 2.0 29 R290LC-7A 2 Speed 13.8 ± 1.0 17.3
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 28.8 ± 2.0 36 R35Z-7 2 Speed 16.0 ± 1.0 20
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 28.8 ± 2.0 36 R35Z-7A 2 Speed 16.0 ± 1.0 20
(2)Travel Speed Evaluation Unit : Seconds / 20 m
Model Travel Speed Standard Maximum allowable 1 Speed 21.8 ± 2.0 27.3 R500LC-7A 2 Speed 13.8 ± 1.0 17.3 Track Revolution Speed Evaluation (3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions Model Travel Speed Standard Maximum allowable 1 Speed 35 ± 2.0 43.7 R300LC-9S 2 Speed 21.1 ± 2.0 26.4
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 28.8 ± 2.0 35.4 R220LC-9S 2 Speed 19.2 ± 2.0 23.4
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 28.0 ± 2.0 35 R210LC-7 2 Speed 18.0 ± 2.0 22.5
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 36.9 ± 2.0 46.1 R290LC-7A 2 Speed 21.0 ± 2.0 26.3
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 19.3 ± 2.0 24 R35Z-7 2 Speed 10.6 ± 2.0 13.2
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 19.3 ± 2.0 24 R35Z-7A 2 Speed 10.6 ± 2.0 13.2
(3)Track Revolution Speed Evaluation Unit : Seconds / 3 revolutions
Model Travel Speed Standard Maximum allowable 1 Speed 38.5 ± 2.0 48 R500LC-7A 2 Speed 24.0 ± 2.0 30 Travel Deviation Evaluation (4)Travel Deviation Evaluation Unit : mm/ 20m Model Standard Maximum allowable Remarks R300LC-9S 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R220LC-9S 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R210LC-7 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R290LC-7A 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R35Z-7 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R35Z-7A 200 below 240
(4)Travel Deviation Evaluation Unit : mm/ 20m
Model Standard Maximum allowable Remarks R500LC-7A 200 below 250 Swing Function Drift Check (6)Swing Function Drift Check Unit : Degree
Model Power mode switch Standard Maximum allowable
P mode (Cluster type 1) R300LC-9S 90 below 157.5 M mode (Cluster type 2)
(6)Swing Function Drift Check Unit : Degree
Model Power mode switch Standard Maximum allowable P mode (Cluster type 1) R220LC-9S 90 below 128.7 M mode (Cluster type 2)
(6)Swing Function Drift Check Unit : Degree
Model Mode select switch Standard Maximum allowable R210LC -7 M mode 90 below 157.5
(6)Swing Function Drift Check Unit : Degree
Model Mode select switch Standard Maximum allowable R290LC-7A H mode 90 below 157.5
(6)Swing Function Drift Check Unit : Degree
Model Standard Maximum allowable Remarks R35Z-7 40 below 50
(6)Swing Function Drift Check Unit : Degree
Model Standard Maximum allowable Remarks R35Z-7A 40 below 50
(6)Swing Function Drift Check Unit : Degree
Model Mode select switch Standard Maximum allowable R500LC-7A H mode 90 below 112.5 Swing Speed Evaluation (5)Swing Speed Evaluation Unit : Seconds / 3 revolutions Model Power mode switch Standard Maximum allowable P mode (Cluster type 1) R300LC-9S 16.8 ± 1.5 21 M mode (Cluster type 2)
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power mode switch Standard Maximum allowable P mode (Cluster type 1) R220LC-9S 15.8 ± 1.5 19 M mode (Cluster type 2)
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power selector switch Standard Maximum allowable R210LC-7 H mode 15.2 ± 1.5 19
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power selector switch Standard Maximum allowable R290LC-7A H mode 16.8 ± 1.5 21
(5)Swing Speed Evaluation Unit : Seconds / 2 revolutions
Model Standard Maximum allowable Remark R35Z-7 12.6 ± 1 15.8
(5)Swing Speed Evaluation Unit : Seconds / 2 revolutions
Model Standard Maximum allowable Remark R35Z-7A 12.6 ± 1 15.8
(5)Swing Speed Evaluation Unit : Seconds / 3 revolutions
Model Power selector switch Standard Maximum allowable R500LC-7A H mode 18 ± 1.5 22.5 Swing Bearing Play Evaluation (7)Swing Bearing Play Evaluation Unit : mm Model Standard Maximum allowable Remarks R300LC-9S 0.5 ~ 1.5 3
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R220LC-9S 0.5 ~ 1.5 3
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R210LC-7 0.5 ~ 1.5 3
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R290LC-7A 0.5 ~ 1.5 3
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R35Z-7 0.5 ~ 1.2 2.4
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R35Z-7A 0.5 ~ 1.2 2.4
(7)Swing Bearing Play Evaluation Unit : mm
Model Standard Maximum allowable Remarks R500LC-7A 0.5 ~ 1.5 3 Hydraulic Cylinder Cycle Time Evaluation
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 4.0 ± 0.4 5 Boom lower 2.5 ± 0.4 3.2 Arm in Regen ON 3.3± 0.4 4.3 R300LC-9S Arm out 3.2 ± 0.3 4 Bucket load 2.4 ± 0.4 2.9 Bucket dump 2.4± 0.3 2.8
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 3.5 ± 0.4 4.1
Boom lower 2.5 ± 0.4 3.2 Arm in Regen ON 3.2± 0.4 3.8 Cluster type 1 Regen OFF 3.7 ± 0.4 4.5 R220LC-9S Arm in (Cluster type 2) 3.7 ± 0.4 4.5 Arm out 3.0 ± 0.3 3.8 Bucket in 2.5 ± 0.4 3.3 Bucket out 2.3 ± 0.3 2.9
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 3.0 ± 0.4 3.8 Boom lower 3.0 ± 0.4 3.8 Arm in 3.2 ± 0.4 4 R210LC-7 Arm out 2.8 ± 0.3 3.5 Bucket load 3.8 ± 0.4 4.8 Bucket dump 2.5 ± 0.3 3.1
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Function Standard Maximum allowable
Boom raise 4.0 ± 0.4 5
Boom lower 3.0 ± 0.4 3.8 Arm in 3.7 ± 0.4 4.6 R290LC-7A Arm out 3.2 ± 0.3 4 Bucket load 2.8 ± 0.4 3.5 Bucket dump 2.6 ± 0.3 3.3
(8)Hydraulic Cylinder Cycle Time Evaluation Unit : Seconds
Model Drift to be measured Standard Maximum allowable
Boom cylinder 10 below 20 R500LC-7A Arm cylinder 10 below 20 Bucket cylinder 40 below 50 Control Lever Operation Force (10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R300LC-9S Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.7 or below 2 Arm Lever 1.7 or below 2 R220LC-9S Bucket Lever 1.4 or below 2 Swing Lever 1.4 or below 2 Travel Lever 2.1 or below 3.15
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R210LC-7 Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.6 or below 2 Arm Lever 1.6 or below 2 R290LC-7A Bucket Lever 1.6 or below 2 Swing Lever 1.6 or below 2 Travel Lever 2.1 or below 3.15 (10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.4 or below 1.9 Arm Lever 1.4 or below 1.9 R35Z-7 Bucket Lever 1.4 or below 1.9 Swing Lever 1.4 or below 1.9 Travel Lever 2.0 or below 2.5
(10)Control Lever Operation Force Unit : kgf
Model Kind of lever Standard Maximum allowable
Boom Lever 1.4 or below 1.9 Arm Lever 1.4 or below 1.9 R35Z-7A Bucket Lever 1.4 or below 1.9 Swing Lever 1.4 or below 1.9 Travel Lever 2.0 or below 2.5
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 87 ± 10 109
Arm Lever 87 ± 10 109 R500LC-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178 Control Lever Stroke (11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 102 ± 10 128 Arm Lever 102 ± 10 128 R300LC-9S Bucket Lever 90 ± 10 113 Swing Lever 90 ± 10 113 Travel Lever 142 ± 10 178
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 112 ± 10 128 Arm Lever 112 ± 10 128 R220LC-9S Bucket Lever 90 ± 10 113 Swing Lever 90 ± 10 113 Travel Lever 139 ± 10 178
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R210LC-7 Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R290LC-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178 (11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R35Z-7 Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 86 ± 10 105
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable
Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R35Z-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 86 ± 10 105
(11)Control Lever Stroke Unit : mm
Model Kind of lever Standard Maximum allowable Boom Lever 87 ± 10 109 Arm Lever 87 ± 10 109 R500LC-7A Bucket Lever 87 ± 10 109 Swing Lever 87 ± 10 109 Travel Lever 142 ± 10 178