Professional Documents
Culture Documents
Select Ivo
Select Ivo
0
Database version
2022.7.20.14.22
Date
11/11/2022
62 Orange Ave
10901 Suffern, NY
Phone: +1 845 504 5098
Fax: +1 845 625 2666
info@fischerfixingsusa.com
www.fischerfixingsusa.com
Design Specifications
Anchor
Anchor system fischer Bolt anchor FAZ II
Anchor Bolt anchor FAZ II 12/20,
zinc plated steel
Calculated anchorage 70 mm
depth
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 1
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
Input data
Design actions *⁾
# NSd VSd,x VSd,y MSd,x MSd,y MT,Sd Type of loading
tf tf tf tfm tfm tfm
1 4.70 0.00 0.25 0.00 0.00 0.00 Permanent-Transient/Static
0.00 - - 0.00 0.00 - Sustained Load
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 2
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
βN,s
Anchor no. % Group N° Decisive Beta
1 41.5 1 βN,s;1
2 41.5 2 βN,s;2
3 41.5 3 βN,s;3
4 41.5 4 βN,s;4
Eq.
(17.4.2.1a/1b)
Eq.
(17.4.2.1c)
Eq.
(17.4.2.2a)
Eq. (17.4.2.4)
Eq.
(17.4.2.5a/5b)
Eq. (17.4.2.6)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 3
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
βN,cb
Anchor no. % Group N° Decisive Beta
1, 2 98.5 1 βN,cb;1
3, 4 98.5 2 βN,cb;2
βV,s
Anchor no. % Group N° Decisive Beta
1 3.0 1 βV,s;1
2 3.0 2 βV,s;2
3 3.0 3 βV,s;3
4 3.0 4 βV,s;4
Eq.
(17.5.3.1a/b)
Eq.
(17.4.2.1a/1b)
Eq.
(17.4.2.1c)
Eq.
(17.4.2.2a)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 4
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
Eq. (17.4.2.4)
Eq.
(17.4.2.5a/5b)
Eq. (17.4.2.6)
βV,cp
Anchor no. % Group N° Decisive Beta
1, 2 2.8 1 βV,cp;1
3, 4 2.8 2 βV,cp;2
Proof successful
Eq. (17.6.3)
Technical Remarks
The transmission of the anchor loads to the supports of the concrete member shall be shown for the ultimate limit state and
the serviceability limit state; for this purpose, the normal verifications shall be carried out under due consideration of the
actions introduced by the anchors. For these verifications the additional provisions given in the current design method shall
be taken into account.
As a pre-condition the anchor plate is assumed to be flat when subjected to the actions. Therefore, the plate must be
sufficiently stiff. The C-Fix anchor plate design is based on a proof of stresses and does not allow a statement about the
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 5
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
stiffness of the plate. The proof of the necessary stiffness is not carried out by C-Fix.
The anchors must be installed in accordance with the manufacture's installation instructions. Please check the latest ICC-ES
Evaluation Report
Supplemental reinforcement: Condition A applies where supplementary reinforcement is present except for pullout and pryout
strength.
Condition B applies where supplemental reinforcement is not present and for pull out or pry out strength.
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 6
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
Installation data
Anchor
Anchor system fischer Bolt anchor FAZ II
Anchor Bolt anchor FAZ II 12/20, Art.-No. 95420
zinc plated steel
Installation details
Thread diameter M 12
Drill hole diameter d0 = 12 mm
Drill hole depth h2 = 90 mm
Calculated anchorage hef = 70 mm
depth
Installation depth hnom = 84 mm
Drilling method Hammer drilling
Drill hole cleaning
Installation type Push-through installation
Annular gap Annular gap not filled
Installation torque Tinst = 0.01 tfm
Socket size 19 mm
Base plate thickness t = 16 mm
Total fixing thickness tfix = 16 mm
Tfix,max tfix, max = 20 mm
Attachment
Profile type Customized profile
Profile dimensions mm
Height 100
Web thickness 3
Flange thickness 3
Load application on X-axis 95
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 7
C-FIX 1.110.0.0
Database version
2022.7.20.14.22
Date
11/11/2022
Anchor coordinates
x y
Anchor no. mm mm
1 -45 130
2 45 130
3 -45 -130
4 45 -130
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 8