Professional Documents
Culture Documents
L-1D
INSTRUCTION MANUAL
(Electrical)
CONTENTS
1. Safety instruction....................................................................................... 1
2. Operation box use...................................................................................... 2
3. Mode setting............................................................................................... 3
4. System parameter table :........................................................................... 4
5. Error codes............................................................................................... 13
6. Definition................................................................................................... 15
1. Safety instruction
Please read the operation manual and related sewing
1.2 Please make sure power off at least 1min and then can open
1.3 Please turn off the power while repairing or wearing needle in
–1–
2. Operation box use
thle
NO Function Describe
Key
Under standby interface, long press the button for 1.5
1 Reset setting
seconds
1. Identify key
2. for the belt clip line function model, the strength of long
2 Identify key press this button to display the thread clamp, LCD display
"[_7]"), press the key again to exit
3. Unlocking
1, Enter different parameter levels (parameters are divided
into 3 levels)In the sewing setting interface, press the "P" key
to enter (parameter interface), and the level I parameter in the
parameter list will be displayed.
Parameters setting In the sewing setting interface, long press the "P" key to enter
3
key
(password input interface). After entering the correct
maintenance password, press the "P" key to enter (parameter
interface). At this time, the level I and I] parameters in the
parameter list will be displayed. Level 2 password: 1111
Under normal sewing interface
1. Adjust the stitch size
–2–
Stop needle
selection 1, Up and down needle selection key
6 2 Thread clamp function on and off.Electronic tension is
key.Thread clamp enabled after open it
function
1,Anti-nest function on and off,is suitable for the machine with
Anti-nest Anti-nest equipment
7 function.Close 2. Close stitch function on and off.After opening,add one more
stitch function stitch,Enhance the reinforcing-sewing effect and reduce the
thread
circulation : front
Front AB Reinforcing-sewing / front double
8
Reinforcing-sewing Reinforcing-sewing /front Four solid Reinforcing-sewing /turn
off
circulation : back
Back A Reinforcing-sewing / back double
9 ocA]
Reinforcing-sewing Reinforcing-sewing /back Four solid Reinforcing-sewing /turn
off
Three segment
-
3. Mode setting
Debug mode: After entering
35
the normal sewing mode, press the right side 3
seconds" enter debug mode.If you want this pattern to return to normal
mode, press "?"key to exit into normal mode
Stitch length Adjustment Mode : After entering sewing mode normally,
long press *3seconds , Entering debug mode, press* + "or*-", switch to
parameter
to parameter P-7, press can correct the go-stitch lemgth switch to parameter
P-8, press can correct the reverse-stitch length, all the corrections are savec to
exit by press Mi].
–3–
Restore Factory settings : In normal sewing mode, long press the
button for more than 1.5 seconds, " will be ence ress +-
dispry
"J"
again
" yes
toadjust to"'no"}, and press the i ect parameters
are restored to the factory mode.
correction value
Back stitch speed can keep needle from breaking while
P-09 500~1500(rpm) 50 800 1
limitation backstitching
–4–
0:Set the number of stitches to set
the value
Set the length of 1:When the length is set to self-made,
P10 the stitch from the number is the number of the 0/1 1 1 i
the set number pattern, that is, the total number of
stitches is the number of stitches x
set the value
Height of middle setting height of presser foot
P-12 presser. foot 0~100 60
lifting (valid lifting when sewing half 1 2
stepping)
Maximum height of setting Maximum height of presser
P
presser foot 0~100 50
lifting (valid foot lifting after trimming 1 2
stepping)
Speed of presser Stepping speed of resser foot
14 foot lifting 20~300(rpm) 10 150 2
(valid stepping) lifting
Speed of presser
P15 foot releasing Stepping speed of presser foot 10 150 2
20~300(rpm)
(valid stepping) releasing
Output duty cycle of Output duty cycle of presser foot soft
PZ 16 presser foot soft drop 0~100 1 0 2
drop
Cutting line for electromagnet:
When the shear line loose line duty
ratio (too small will affect the shear
Cut and loosen
P line electromagnet suction strength) 0-100 1 50 2
duty cycle
Cutting line for step
Loose line efforts to adjust the
(light)
Front Immediately after the end of front
reinforcing-sewin reinforcing-sewing, step on the
P-18 g setting after cutting line without the function 0/1 1 0 1
P-22 soft start speed 2 speed of the 2 nd needle of soft start 100~3000(rpm) 50 1000 1
–5–
The functionsetting of automatically
P-27
Power on and finding the needle position when the 1 0 1
positioning power is on 0 unavailable 1
available
Setting of signal mode of turn/lift
signal mode for switch of
P-28 0/1/2 1 0 1
turn/lift switch machine head 0: always open 1:
always close 2: forbid a protection
To set presser foot soft lowering time
Presser foot soft
P-29 The longer time the lower speed of the 100500 (ms) 5 80 2
lowering time
presser foot
Baseline count
P-30 0: unavailable 1: available 0/1 1 1
enable
Baseline initial
P
value setting
Baseline initial value setting 200~4000(0.1m) 20 160 1
Stop time of
decorative
Stop time of decorative tacking
«
counting by piece
Turn off time
P-39
Turn off time before presser foot soft
before presser 0~50 1 12 2
drop
foot soft drop
P-41 Low speed The lowest speed of pedal 100-500(rpm) 10 200 1
P-47
knee presses the When running, the knee presses the
foot to judge the foot to judge the speed
speed
When running the 0~100 0 2
When running the knee is raised by the 1
P-48 knee is raised by
foot
the foot
–6–
P-49 1~60 1 25
time time to force off
output time of 0~800(ms)
P-50
presser foot presser foot lifting
lifting
output duty cycle 0~100
of presser foot
output duty cycle of presser foot
P-§1 lifting 1 40
presser foot
hold time of presser foot lifting
lifting
starting
P-§3 reinforcing-sewin starting reinforcing-sewing speed 100~3000(rpm) 50 1800
g speed
Compensation
80-120 1 100
tacking sewing
sewing
Compensation
80~120 1 100
sewing
ending
P-56 reinforcing-sewin ending reinforcing-sewing speed 100-3000(rpm) 50 1800
g speed
starting
80~120 1 100
sewing
starting
80~120 1 100
back tacking sewing
tacking sewing
Continuous
P-59 reinforcing-sewin Continuous reinforcing-sewing speed 100~3000(rpm) 50 1800
g speed
1 0
g break)
may
10~100(0.1 BE) 1 40
medium pedal)
Pedal travel at Pedal position at highest rotating
P-64 highest rotation speed (Travel relative to medium 10~150(0.1 BE) 1 110
speed pedal)
–7–
Down needle
P-69 positioning To adjust down needle position 0~240 1 165
position
Reversal of needle lift function
P-70 after thread 0/1 1 0
trimming 0: unavailable 1: available
Reversal of needle lift
angle 0~45() 1 20
Thread clamp Adjust the thread clamp strength size
P-72 strength 0: Cli p line function is invalid 0~9 1 7
adjustment 1 9: Three Intensity Adjustment
10~150() 5 120
Thread pressing ~
Pedal speed 1
P-89
line release line release Angle 0~360 2 350
1 1
1 +
1 0
pedal
Anti-nest Anti-nest function selection: 0: hread
P-95 function clamp type 1; Anti-next type 2: 0/1/2 1 0
selection thread wiper type
0/1 1 1
1 0
pattern stitches
–8–
Presser foot Presser foot height sensor function
P-105 height 1 1 2
function setting setting 0: unavailable 1; available
The voltage
The voltage adjustment at zero
adjustment at zero
P-106 position of position of presser foot height 0~250 1 215 2
sensor (unit: 0.0lv) (presser foot
presser foot drop, feed dog is under the table)
height sensor
Overthickness Presser foot height sensor' s coltage
P
detection setting of overthickness detection 0-500 5 100 2
sensitivity Unit: mv) (Relative to the zero
setting position voltage)
Full pressure duty Full pressure duty cycle of thread
P-108 cycle of thread trimming (Buffering during the thread 50~100 1 90 2
trimming trimming and closing)
Force adjustment
Force adjustment of electromagnet for
of electromagnet
P
for presser foot presser foot lifiting (Cushion when 50~100 1 65 2
press foot is absorbed)
lifiting
Material
P 110 thickness and
Increase tension when sewing thick 1 0 2
material
tension control
Overthickness
P Limit speed of overthickness 500~3000(rpm) 50 1500 2
sewing speed
Overthickness
P-112 stitch offset Overthickness stitch offset deals 50~150(%) 1 120 2
coefficient
Needle compensate stitch length
Needle compensate
P-113 mode: Invaild:
stitch leng th mode set stitch 1 vaild (press P114 to 0/1 1 0 1
length)
Needle compensate stitch length
Needle compensate setting
Parameter range of Stitch length 5mm
P-114 stitch length 10~ 50 (70) mm 1 35 1
type (1. Omm 5. Omm)
setting Parameter range of stitch length 5mm
type (1. Omm"7. Omm)
Reverse sewing 0: reverse sewing 1: tightly sewn
P-115 button function 2: reverse sewing 0~3 1 0 2
setting 3: reverse sewingtreverse sewing
O: reverse sewing 1: tightly sewn
P-116
fill needle button 2: reverse sewing 0~3 1 2 2
function setting 3: reverse sewingtreverse sewing
Dense needle Pitch
P-117 Head button stitch stitch set 50~150 1 110 2
setting
Number of pretty Number of pretty sewing needle
P-118 sewing needle 1~10 1 2 2
setting setting
Pretty sewing
P-119 needle distance Pretty sewing needle distance setting 50~150 1 107 2
setting
Start trimming
P-121 angle of Paragraph Start trimming angle of Paragraph 1 200~300 2 230 2
P
Paragraph 1 stroke stroke of trimming 0~100 40
of trimming Paragraph 1 1 2
Start trimming
P-123 angle of Paragraph Start trimming angle of Paragraph 2 250-360 2 330 2
Paragraph 2 stroke
P
of trimming Paragraph 2 stroke of trimming 0~100 1 65 2
–9–
loose thread
P-126 enable when start 0: invaild 1: vaild 0/1 1 1
sewing
start-sewing loose 0~1000 10 100
loose thread
10 200
Display backlight
P-129 brightness Display backlight brightness Setting 0-10 1 5
Setting
0-1 1 0
parameter as factory parameter
Midway reverse
P-135 function 0: unavailable 1: available 0~1 1 0
selection
1~50 1 4
forth set
Q-1 1 0
time
P-139 Lock screen time setting: 0°240 (s) 0~1 1 20
1 100
Anti-nest
5 50
Anti-nest
Maxinum Maximum needle distance setting
e
setting
First off-line
P-151 prevented stitch 0.invaild 1. vaild 0~1 1 0
length
First off-line
length setting
Head button 0: Invalid »
1 0
– 10 –
0: Needle bar light off
Needle bar lamp
1 5: Adjust the brightness of needle
P-155 brightness 0-5 2
bar lamp of 5 gears ( HMI control
setting 0/1/2/3/4/5/Oswitch)
Back sewing mode setting
Back sewing switch 0: Back sewing only
P-157 1: back sewing plus attach stitch 0/1/2 1 0 1
function setting 2: Back sewing only, no action in
standby mode
Full pressure
output time of Full pressure output time of presser
P-158 back sewing (only 0~800(ms) 10 150 2
foot
presser foot,
thread trimming)
Output duty cycle
of back sewing
P-159 (only presser Output duty cycle of presser foot 0~100 1 40 2
foot, thread
trimming)
Backing sewing Forced turnoff after back sewing
P 0~60 (S) 1 12 2
duration duration
Front tacking
sewing Stitch compensation parameters of
P 161 compensation] (onl front tacking sewing 0~100 1 23 1
y presser foot,
thread trimming)
Front tacking
sewing Stitch compensation parameters of
P-162 compensation2 (onl front tacking sewing 0~100 1 15 1
y presser foot,
thread trimming)
ending
reinforcing-sewin
compensationl Stitch compensation parameters of 0~100 1 30 1
(only presser ending reinforcing-sewing
foot, thread
trimming)
ending
reinforcing-sewin
P-164 compensation2 Stitch compensation parameters of 0~100 1 18 1
(only presser ending reinforcing-sewing
foot, thread
trimming)
Continuous
reinforcing-sewin
P-165 compensation1 Stitch compensation parameters of 0~100 1 30 1
(only presser Continuous reinforcing-sewing
foot, thread
trimming)
Continuous
reinforcing-sewin
P166 g compensation2 Stitch compensation parameters of 0~100 1 10 1
(only presser Continuous reinforcing-sewing
foot, thread
trimming)
Compensate system 0, P171~P176 Invalid parameter
P-170 enablement by 0~1 1 1 2
-1, P171~P176 Invalid parameter
speed
Speed clockwise
P-171 Speed clockwise sewing compensate 50~150 100
sewing 1 2
system
compensation
Speed
anti-clockwise Speed anti-clockwise sewing
P 50~150 1 100 2
sewing compensate system
compensation
– 11 –
Starting
reinforcing-sewin Speed Clockwise sewing compensation
P-173 speed Clockwise coefficient 1 2
sewing
compensation
Starting
reinforcing-sewin
174 g speed Speed Anti-clockwise sewing 50~150 1 100 2
Anti-clockwise compensation coefficient
sewing
compensation
ending
reinforcing-sewin Speed Clockwise sewing compensation
P-175 g speed Clockwise coefficient 1 100 2
sewing
compensation
ending
reinforcing-sewin
176 g speed Speed Anti-clockwise sewing 50~150 1 100 2
Anti-clockwise compensation coefficient
sewing
compensation
Compensate system =0, P181 P200 Invalid parameter
P-180 enablement by 0~1 1 1 2
stitch length -1, P181 P200 Invalid parameter
lmm Clockwise
Imm Clockwise sewing compensation
P-181 sewing 50-150 1 100 2
coefficient
compensation
lnm
Anti-clockwise Anti-clockwise sewing
J sewing
lmm
compensation coefficient 50~150 1 100 2
compensation
2mm Clockwise
2mm Clockwise sewing compensation
P-183 sewing coefficient 50~150 1 100 2
compensation
2mm
Anti-clockwise 2mm Anti-clockwise sewing
P-184 coefficient 50~150 1 100 2
sewing compensation
compensation
3mm Clockwise
185
3mm Clockwise sewing compensation
sewing 50~150 1 100 2
coefficient
compensation
3mm
186
Anti-clockwise 3mm Anti-clockwise sewing
50~150 1 100 2
sewing compensation coefficient
compensation
4mm Clockwise 4mm Clockwise sewing compensation
187 sewing 50~150 1 100 2
coefficient
compensation
4mm
Anti-clockwise 4mm Anti-clockwise sewing
P 50~150 1 100 2
sewing compensation coefficient
compensation
5mm Clockwise
5mm Clockwise sewing compensation
P-189 sewing 50~150 1 100 2
coefficient
compensation
5mm
Anti-clockwise 5mm Anti-clockwise sewing
P-190 coefficient 50~150 1 100 2
sewing compensation
compensation
6mm Clockwise 6mm Clockwise sewing compensation
P-191 sewing coefficient 50~150 1 100 2
compensation
– 12 –
6mm
Anti-clockwise 6mm Anti-clockwise sewing
P-192 50~150 1 100 2
sewing compensation coefficient
compensation
7mm Clockwise
7mm Clockwise sewing compensation
P-193 sewing 50~150 1 100 2
coefficient
compensation
7mm
Anti-clockwise 7mm Anti-clockwise sewing
P-194 50~150 1 100 2
sewing compensation coefficient
compensation
5. Error codes
Error Code Contents Possible reasons Checking and treatment
If electric engine plug is well
contacted;
€011
Motor signal error
Motor position sensor if electric engine signal detecting
£012 signal failure device has been broken;
if sewing machine handwheel correctly
installed.
If electric engine plug is well
contacted;
if machine head or thread-cutting
E021 motor stall mechanism has been
Motor overload
E023 motor overload blocked completely;f materials are too
thick;
Electrical signal detection signal
whether the normal.
Current detection Current detection loop system is
E101
Hardware drivers abnormal working
fault Driving hardware properly;Whether the damage to the
error device driver.
System into line voltage is too high;
High input voltage
E111 Brake circuit fault Braking resistance are working
Voltage too high Voltage detection properly;
€112
error System voltage detection circuit are
working properly.
Actual low voltage
If the voltage on the inlet wire is too
E121 low Whether the
Voltage too low Voltage detection is circuit
E122 system voltage detection the
wrong normal work.
E131 Current circuit Current detection Current detection loop system is
fault abnormal working properly.
E133 Oz circuit fault Oz circuit fault Oz circuit system is working properly.
Automatic resistance Brake resistor plug is in good contact
£134 DBFLT malfunction
circuit failure Brake resistance is damaged
Current detection loop system is
Current detection
E201 over current working properly
error Electrical signal is normal.
E211 Abnormal motor Current or voltage If electric engine plug is well
detection error contacted
E212 operation If electric engine signal
Communication
if operation box plug is well contacted;
£301
error Sci circuit error if operation box components are
damaged.
E302 Operation inner Sci circuit error check whether the operating box is
failure damaged.
– 13 –
E303 Sci circuit error check whether the main control board is
breakdown damaged.
E304
the operating box is
failure
E402 Pedal ID fault verification Pedal connection is loosen.
E403 pedal is
E502 Fuel fault alarm Fuel fault alarm Add oil Tips
Current detection loop system is
E601
fault
Current detection loop system is
E602
fault
drivers Current detection
E603 working properly: Whether the damage to
circuit the device driver.
Feed motor STEP2 The
£604 Motor signal error initial mechanical Feed motor connector is a good contact
angle
E605
rotor stuck
Current detection loop system is
E606
fault
E607
drivers
overcurrent the device driver.
E608
drivers
overcurrent the device driver.
Hardware drivers
E609
fault
Presser foot trimming
E610
angle
Presser foot trimming
£611
is a good contact Machinery is stuck
rotor stuck
drivers
E612 motor STEP1 Motor working properly;Whether the damage to
winding circuit the device driver.
d mo
E613
Current detection loop system is
the device driver.
The Presser foot Feed motor connector is a good contact
E614
or rotor stuck the device driver.
P.OFF Power off Display Power off Wait for power supply to resume.
EVAL Trial expired Trial expired Contact the dealer processing
L.bob
The bottom line
Press key to enter the interface,
P.bob
state
– 14 –
6. Definition
@Burn connector
4 Spindle motor power cord
1
connector
©) Spindle motor encoder
connecto
© Stepper motor encoder
connector
@ Stepper motor power cord
connector
(USB connector
@Oil level warning connector
Control box wire connector
@)Fan wire connector
103
stitch 10
Defin Back
Electromag groun Electromag Electromag Electromag
compens
ition net voltage stitch d net voltage net voltage net voltage
ation
– 15 –
Company Name ADD TEL FAX HTTP E-Mail
20 BENDEMEER ROAD,
JUKI SINGAPORE #04-12 BS BENDEMEER (65)6553-4 http: //www.ju we.sgp-sales@ml.ju
PTE LTD. CENTRE SINGAPORE 388 ki.com.sg/ ki.com
339914
153 HOA LAN STR.,
JUKI Machinery
WARD 2, (84)28-351 (84)28-351
Vietnam Company sales@jukimv.com
PHU NHUAN DIST., HO 78833 78318
Ltd
CHI MINH CITY, VIETNAM
UL.POLECZKI 21(PLATAN
JUKI CENTRAL (48)22-545 (48) http://jukieuro
PARK C) 02-822
EUROPE -0400 22-5450411 pe.com/
WARSAW, POLAND
8500 NW 17TH STREET,
(1)305-594 https: //juki.co
JUKI America INC SUITE 100, DORAL, FL
-0059 m/
33126-1035, U.S.A.
– 16 –