Professional Documents
Culture Documents
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 1 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 2 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 3 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 4 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 5 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 6 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 7 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 8 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 9 of 10
Blue Rock Quarry Alfred Road Estcourt
TEL: (036) 3521244 or 0717261521
ATTENTION: Phillip TEL NO:
COMPANY: Bergmix Internal Checks - Phillip FAX NO:
REPORT No: 47669 CELL NO: 082 788 8218
PROJECT: Phillip Internal EMAIL: phillip@bergmix.co.za
PROBLEM CODES
1 Cube honeycombed/voided 2 Cube damaged 3 Cube mass low 4 Abnormal cube failure pattern 5 Cube dimensionally non-standard 6 Test results low strength 7 Test results
exceed allowed variance 8 Cubes received and tested dry 9 Non-std test, SABS requires 3 cubes/ set/ test age 10 See attached photo's 11 No concrete specification given to
CMT LAB 12 High variance of test results
CMT LAB cured cubes, where possible and conducted strength testing on cubes, however, CMT LAB was not involved in any processes that were outside its scope of work,
as defined by the customer. Such processes may have included sampling concrete, making, transporting and curing of cubes, as relevant. Cubes were cured by CMT LAB
from date received to date tested, as relevant
SABS 0100-2, clause 3.5.4, states: "valid test result: the average result obtained from three test cubes of concrete that have been tested in accordance with SABS method 863,
with the additional reuirement that curing water must be maintained at a temperature between 22 deg C and 25 deg C".
SABS 0100-2, clause 14.3.1.4, states: "The cubes shall be tested in accordance with SABS method 863. Three cubes shall be tested for acceptance at the age specified, which is
usually 28 days. For prestressed concrete, sets of three cubes shall be tested at 3 days. Sets of three cubes may be tested at other ages for information".
SABS method 863, clause 4, states: "Obtain samples of concrete and prepare and cure a set of three test specimens, as described in the relevant clauses of SABS method 862-
3, respectively".
If the cube strengths given in this report are to be used for acceptance in accordance with SABS 0100-2 (or any other specification with similar requirements to those of SABS
0100-2) then the above requirements must be complied with otherwise, acceptance based on cube strengths using the results given in this report, cannot be made
Reported on: 07 December 2020 at 15:20 CMT Laboratories (Pty) Ltd Reg:2017 TD 025/01 Page 10 of 10