Professional Documents
Culture Documents
id091000802600
id091000802600
ac5uuw00008886
Set plate
2
(See SET PLATE REMOVAL/INSTALLATION.)
Shroud panel
3
(See SHROUD PANEL REMOVAL/INSTALLATION.)
Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.)
4
(See FRONT BUMPER DISASSEMBLY/ASSEMBLY.)
Hood
(See HOOD REMOVAL/INSTALLATION.)
6 (See HOOD DISASSEMBLY/ASSEMBLY.)
Cowl panel
7
(See COWL PANEL REMOVAL/INSTALLATION.)
Fuel-filler lid
(See FUEL-FILLER LID REMOVAL/INSTALLATION.)
8
(See FUEL-FILLER LID ADJUSTMENT.)
Energy-absorbing form
15
(See ENERGY-ABSORBING FORM REMOVAL/INSTALLATION.)
Seal plate
16
(See SEAL PLATE REMOVAL/INSTALLATION.)
Rear bumper
(See REAR BUMPER REMOVAL/INSTALLATION.)
20
(See REAR BUMPER DISASSEMBLY/ASSEMBLY.)
id091000822500
2.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00008897
5.Disengage the pins and hook, remove the front bumper slider.
ac5uuw00008898
5.Disengage the pins and hook, remove the rear bumper slider.
id091000888900
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front under cover No.1 (See FRONT
UNDER COVER No.1 REMOVAL/INSTALLATION.) (4)Charge air cooler (SKYACTIV-D 2.2) (See
CHARGE AIR COOLER REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) (5)Active air shutter (with
active air shutter) (See ACTIVE AIR SHUTTER REMOVAL/INSTALLATION.)
3.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00008908
6.Move the bumper stiffener lower in the direction of arrows (1), (2) and remove the hooks.
id091000802000
(1)Windshield wiper arm and blade (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION.) (2)Cowl grille (See COWL GRILLE REMOVAL/INSTALLATION.)
(3)Windshield wiper motor and link (See WINDSHIELD WIPER MOTOR AND LINK
REMOVAL/INSTALLATION.) (4)Keyless beeper (with advanced keyless entry system) (See
KEYLESS BEEPER REMOVAL/INSTALLATION.)
3.Disconnect the wiper de-icer connector. (with wiper de-icer) (See WINDSHIELD REMOVAL.) (See
WINDSHIELD INSTALLATION.)
ac5uuw00009395
id091000888800
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Set plate (See SET PLATE
REMOVAL/INSTALLATION.)
3.Insert the flathead screwdriver shown in the figure, push the fasteners from back side of front bumper
reinforcement.
ac5uuw00008907
4.Pull the energy-absorbing form in the direction of arrow (2) shown in the figure while detaching guides.
id091000800400
1.Remove the front fog lights. (with front fog lights) (See FRONT FOG LIGHT
REMOVAL/INSTALLATION.)
id091000800600
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Set plate (See SET PLATE
REMOVAL/INSTALLATION.) (4)Energy-absorbing form (See ENERGY-ABSORBING FORM
REMOVAL/INSTALLATION.) (5)Front under cover No.1 (See FRONT UNDER COVER No.1
REMOVAL/INSTALLATION.) (6)Bumper stiffener lower (See BUMPER STIFFENER LOWER
REMOVAL/INSTALLATION.) (7)Charge air cooler (SKYACTIV-D 2.2) (See CHARGE AIR COOLER
REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) (8)Active air shutter (with active air shutter) (See
ACTIVE AIR SHUTTER REMOVAL/INSTALLATION.)
Caution
• Because the shroud panel is installed to the bumper reinforcement, support the shroud panel using
a jack before removing the bumper reinforcement so as not to apply excessive force to the shroud
panel.
Warning
• Removing the front bumper reinforcement without supporting it could cause the front bumper
reinforcement to fall and cause serious injury. Always perform the procedure with at least another
person to prevent the front bumper reinforcement from falling.
id091000800300
1.Affix the protective tape to the position shown in the figure to prevent scratches and damage.
ac5uuw00005157
3.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00008866
ac5uuw00009577
ac5uuw00005160
8.Slightly bend back the front under cover No.1 and remove the fasteners.
ac5uuw00005162
10.Pull the rear end of the front bumper in the direction of the arrow shown in the figure and detach the
front bumper from the front bumper slider while removing the tabs.
Caution
• Carefully remove the front bumper from the front bumper slider. If the front bumper is removed from
the front bumper slider with excessive force, the front bumper hooks may be damaged because the
front bumper and the front bumper slider are engaged firmly.
• Detach the front bumper hooks from the front bumper slider using two people, one person supports
the front bumper. If the front bumper hooks are detached from the front bumper without supporting
the front bumper, it may fall off and be damaged.
11.Pull the front bumper in the direction of the arrows shown in the figure and pull out the locator pin.
ac5uuw00005165
Warning
• After removing the front bumper, secure the front over fender and front mudguard with tape to
prevent the front over fender from being damaged and to prevent injury.
id091000804000
1.Remove the front over fender. (See FRONT OVER FENDER REMOVAL/INSTALLATION.)
ac5uuw00008895
1.Remove the front over fender. (See FRONT OVER FENDER REMOVAL/INSTALLATION.)
3.Move the front fender insulator No.2 in the direction of the arrows and remove it.
id091000801000
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front combination light (See FRONT
COMBINATION LIGHT REMOVAL/INSTALLATION.) (4)Front bumper slider (See BUMPER
SLIDER REMOVAL/INSTALLATION.) (5)Front over fender (See FRONT OVER FENDER
REMOVAL/INSTALLATION.) (6)Edge rubber
ac5uuw00008876
ac5uuw00006858
9.Remove the front fender cover in the direction of the arrow shown in the figure.
id091000803900
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front combination light (See FRONT
COMBINATION LIGHT REMOVAL/INSTALLATION.)
ac5uuw00008887
ac5uuw00008889
9.Install in the reverse order of removal. (See Front Fender Stay Paint Note.)
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front combination light (See FRONT
COMBINATION LIGHT REMOVAL/INSTALLATION.)
ac5uuw00008892
8.Install in the reverse order of removal. (See Front Fender Stay Paint Note.)
Caution
• If the bolt contact area is painted when the front fender stay is newly replaced, it could cause a
malfunction in the PCM. Before painting a newly replaced part, protect the bolt contact areas with
masking tape.
Note
• After installing the bolt, apply touch-up paint to the exposed base material area of the front fender
stay.
id091000878700
ac5uuw00008899
2.Pull the lower front over fender in the direction of the arrow shown in the figure and disengage the tabs.
ac5uuw00008900
ac5uuw00005174
Warning
• When installing the front over fender, verify that clips are not damaged, if they are damaged,
replace them with new ones. Otherwise, the front over fender may fall off while the vehicle is being
driven, leading to a serious accident.
id091000800100
ac5uuw00008864
id091000965300
ac5uuw00009381
2 Hood insulator
5 Stop rubber
6 Hood
id091000801200
Warning
• Always perform the procedure with at least another person to prevent the hood from falling.
Otherwise, the hood may fall and cause injury.
ac5uuw00006798
id091000800800
ac5uuw00008875
1 Rear reflector
id091000800900
3.Remove the hanger rubber in the direction of the arrow shown in the figure.
ac5uuw00007993
4.Remove nuts.
Warning
• Removing the rear bumper reinforcement without supporting it could cause the rear bumper
reinforcement to fall and cause serious injury. Always perform the procedure with at least another
person to prevent the rear bumper reinforcement from falling.
5.Remove the rear bumper reinforcement in the direction of the arrow shown in the figure.
id091000800700
1.Affix the protective tape to the position shown in the figure to prevent scratches and damage.
ac5uuw00008869
3.Remove the rear combination right. (See REAR COMBINATION LIGHT REMOVAL/INSTALLATION.)
ac5uuw00008870
ac5uuw00008871
ac5uuw00008872
9.Press the tab of rear under cover and remove it. (with rear under cover)
ac5uuw00005110
11.Detach the rear bumper from the rear bumper slider while holding the rear end of the rear bumper,
moving it in the direction of the arrows shown in the figure, and detaching the hooks.
12.Move the rear bumper in the direction of the arrow shown in the figure and detach it from rear bumper
bracket.
ac5uuw00008874
Warning
• After removing rear bumper, it may hit the rear over fender and cause a damage and/or injury.
Perform the following procedure to prevent the rear over fender from being damaged.
― Fix the rear over fender and rear fender panel with protective tape.
15.If the rear bumper is replaced, perform the blind spot monitoring (BSM) radar test. (with blind spot
monitoring (BSM) system) (See BLIND SPOT MONITORING (BSM) RADAR TEST.)
Caution
• If the rear bumper installation position is changed or individual differences (coating film/thickness)
occur, the blind spot monitoring (BSM) control module radar angle will deviate which could result in
the module not detecting a vehicle approaching from the rear correctly. If the rear bumper is replaced,
perform the blind spot monitoring (BSM) radar test.
id091000878800
ac5uuw00008901
ac5uuw00008902
ac5uuw00008903
4.Pull the rear over fender in the direction of the arrow shown in the figure and remove it.
Warning
• When installing the front over fender, verify that clips are not damaged, if they are damaged,
replace them with new ones. Otherwise, the front over fender may fall off while the vehicle is being
driven, leading to a serious accident.
id091000466600
ac5uuw00008863
2.Remove the seal board upper in the direction of the arrow shown in the figure.
id091000889000
2.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00008910
5.Remove the seal plate in the direction of the arrow shown in the figure while detaching the tab.
id091000878900
2.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00008905
8.Remove the set plate in the direction of the arrow shown in the figure.
id091000801900
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front combination light (See FRONT
COMBINATION LIGHT REMOVAL/INSTALLATION.) (4)Set plate (See SET PLATE
REMOVAL/INSTALLATION.) (5)Energy-absorbing form (See ENERGY-ABSORBING FORM
REMOVAL/INSTALLATION.) (6)Front under cover No.1 (See FRONT UNDER COVER No.1
REMOVAL/INSTALLATION.) (7)Active air shutter (with active air shutter) (See ACTIVE AIR
SHUTTER REMOVAL/INSTALLATION.) (8)Charge air cooler (SKYACTIV-D 2.2) (See CHARGE
AIR COOLER REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) (9)Bumper stiffener lower (See
BUMPER STIFFENER LOWER REMOVAL/INSTALLATION.) (10)Seal plate (See SEAL PLATE
REMOVAL/INSTALLATION.) (11)Front bumper reinforcement (See FRONT BUMPER
REINFORCEMENT REMOVAL/INSTALLATION.) (12)Horn (See HORN
REMOVAL/INSTALLATION.) (13)Shroud upper member (See SHROUD UPPER MEMBER
REMOVAL/INSTALLATION.) (14)Radar unit (with Mazda radar cruise control (MRCC) system) (See
RADAR UNIT REMOVAL/INSTALLATION.) (15)Hood latch (See HOOD LATCH
REMOVAL/INSTALLATION.) (16)Crash zone sensor (See CRASH ZONE SENSOR
REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM - MEXICO SPEC.].)
(See CRASH ZONE SENSOR REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL
SYSTEM - US/CANADA SPEC.].) (17)Ambient temperature sensor (See AMBIENT
TEMPERATURE SENSOR REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER].)
(18)Fresh air duct installation bolt (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)].) (See INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER
DEACTIVATION)].) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
3.While pressing the tabs of wiring harness clips A and B in the directions of the arrows, remove wiring
harness clips A and B secured to the shroud panel.
ac5uuw00006859
ac5uuw00008883
6.Pull up the radiator in the direction of arrow (1) shown in the figure.
Warning
• Removing the shroud panel without supporting it could cause the shroud panel to fall and cause
serious injury. Always perform the procedure with at least another person to prevent the shroud panel
from falling.
7.Pull down the shroud panel in the direction of arrow (2) shown in the figure, then remove it from the
radiator mount guide.
Caution
• Support the lower surface of the radiator with a jack to prevent the radiator from falling off after the
shroud panel is removed.
11.Adjust the radar unit aiming. (with MRCC system) (See RADAR UNIT AIMING.)
id091000889800
(1)Seal board upper (See SEAL BOARD UPPER REMOVAL/INSTALLATION.) (2)Front bumper
(See FRONT BUMPER REMOVAL/INSTALLATION.) (3)Front combination light (See FRONT
COMBINATION LIGHT REMOVAL/INSTALLATION.) (4)Horn (See HORN
REMOVAL/INSTALLATION.)
ac5uuw00006844