Professional Documents
Culture Documents
id091700800200
id091700800200
ac5uuw00007540
Meter hood
2
(See METER HOOD REMOVAL/INSTALLATION.)
Ventilator grille
3
(See VENTILATOR GRILLE REMOVAL/INSTALLATION.)
Speaker grille
4
(See SPEAKER GRILLE REMOVAL/INSTALLATION.)
Dashboard
(See DASHBOARD REMOVAL/INSTALLATION.)
5
(See DASHBOARD DISASSEMBLY/ASSEMBLY.)
Foot support
8
(See FOOT SUPPORT REMOVAL/INSTALLATION.)
Cluster switch
14
(See CLUSTER SWITCH REMOVAL/INSTALLATION.)
ac5uuw00005782
Ventilator grille
3
(See VENTILATOR GRILLE REMOVAL/INSTALLATION.)
Sunvisor
4
(See SUNVISOR REMOVAL/INSTALLATION.)
A-pillar trim
6
(See A-PILLAR TRIM REMOVAL/INSTALLATION.)
Column cover
7
(See COLUMN COVER REMOVAL/INSTALLATION.)
Glove compartment
8
(See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)
Side wall
9
(See SIDE WALL REMOVAL/INSTALLATION.)
Switch panel
13
(See SWITCH PANEL REMOVAL/INSTALLATION.)
Cup holder
14
(See CUP HOLDER REMOVAL/INSTALLATION.)
Rear console
(See REAR CONSOLE REMOVAL/INSTALLATION.)
15 (See REAR CONSOLE DISASSEMBLY/ASSEMBLY.)
ac5uuw00005783
Headliner
2
(See HEADLINER REMOVAL/INSTALLATION.)
C-pillar trim
3
(See C-PILLAR TRIM REMOVAL/INSTALLATION.)
Assist handle
5
(See ASSIST HANDLE REMOVAL/INSTALLATION.)
Floor covering
9
(See FLOOR COVERING REMOVAL/INSTALLATION.)
Trunk board
7
(See TRUNK BOARD REMOVAL/INSTALLATION.)
Sub-trunk
8
(See SUB-TRUNK REMOVAL/INSTALLATION.)
id091700804600
Driver-side
4.Insert the remover tool into the positions shown in the figure, move it in the order of arrows (1) and (2),
and detach the hooks.
Passenger-side
4.Insert the remover tool into the positions shown in the figure, move it in the order of arrows (1) and (2),
and detach the hooks.
4.Using a tape-wrapped flathead screwdriver, move it in the direction of arrow (1) shown in the figure and
while detaching the hook from the upper decoration panel, slide the center ventilator grille in the direction
of arrow (2) to remove it.
ac5uuw00006679
4.Remove the rear vent duct in the direction of the arrow shown in the figure.
6.Insert a tape-wrapped flathead screwdriver in the positions shown in the figure, move it in the order of
arrows (1) and (2) and detach the hooks.
7.Move the rear ventilator grille in the order of arrows (1) and (2), and remove it while detaching the
hooks.
id091700803100
3.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the direction
of arrow (1), and while detaching the hooks of the remote handle lever, open the cover in the direction of
arrow (2). (With remote handle lever)
ac5uuw00005394
12.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the
direction of the arrows, and remove the clips.
13.Move the trunk side trim in the order of arrows (1) and (2) shown in the figure, and detach the hook
from the body panel.
14.Move the trunk side trim in the order of arrows (1), (2), and (3) shown in the figure, and remove the
clips and hooks. (Left side) (With remote handle lever)
15.Move the trunk side trim in the order of arrows (1), (2), and (3) shown in the figure, and remove the
clips and hooks. (Left side and Right side) (Without remote handle lever)
16.Move the trunk side trim in the order of arrows (1), (2), and (3) shown in the figure, and remove the
clips, hooks, and the clip of the remote handle lever. (Right side) (With remote handle lever)
17.Insert a hand into the back side of the trunk side trim, press the tabs of the remote handle lever in the
direction of arrows (1) shown in the figure, and remove the remote handle lever in the direction of arrow
(2). (With remote handle lever)
18.Set the remote handle lever aside. (With remote handle lever)
ac5uuw00005403
ac5uuw00005827
id091700803400
1.Disconnect the negative battery terminal. (With Bose®) (See NEGATIVE BATTERY TERMINAL
DISCONNECTION/CONNECTION.)
ac5uuw00005382
ac5uuw00005383
5.Move the trunk end trim in the order of arrows (1) and (2) shown in the figure, remove it while detaching
the clips, pins, and the guides.
id091700460400
2.Remove the console side panel. (See CONSOLE SIDE PANEL REMOVAL/INSTALLATION.)
3.Using a remover tool, move the switch panel in the order of arrows (1), (2), (3), and (4) shown in the
figure, detach the clips, and remove the switch panel.
ac5uuw00005251
Note
• When replacing the switch panel, remove the electric parking brake switch. (With commander
switch) (SeeELECTRIC PARKING BRAKE SWITCH REMOVAL/INSTALLATION.)
id091700810000
1.Move the center trunk board in the direction of the arrows shown in the figure, and remove the ends of
the center trunk board from the gap between the trunk side trim and the rear seat back.
ac5uuw00005385
2.Remove the center trunk board in the direction of the arrow shown in the figure.
1.Move the trunk board RH and trunk board LH in the direction of the arrows shown in the figure while
detaching the clips.
ac5uuw00005387
id091700801700
1.Disconnect the negative battery terminal. (With vanity mirror illumination) (See NEGATIVE BATTERY
TERMINAL DISCONNECTION/CONNECTION.)
2.Insert a tape-wrapped flathead screwdriver into the position shown in the figure.
ac5uuw00007931
3.Move the tape-wrapped flathead screwdriver in the direction of the arrow shown in the figure, detach
the tab, and remove the sunvisor cap.
5.Move the sunvisor in the direction of the arrow shown in the figure and detach the hook.
6.Disconnect the vanity mirror illumination connector. (With vanity mirror illumination)
7.Using two tape-wrapped flathead screwdrivers, press the center adapter tabs in the direction of arrows
(1) shown in the figure, and remove the center adapter in the direction of arrow (2).
id091700998600
1.Disconnect the negative battery terminal. (With Bose®) (See NEGATIVE BATTERY TERMINAL
DISCONNECTION/CONNECTION.)
4.Remove sub-trunks No.1 and No.2 in the direction of the arrows shown in the figure.
ac5uuw00005391
id091700805400
Driver-side
1.Remove the clip and hooks while pulling the side wall in the order of arrows (1) and (2) shown in the
figure.
Caution
• If the side wall is pulled forcibly when removing the hooks and clip, the guide could be damaged.
When pulling the side wall in the direction of arrows (1) and (2), be careful not to damage the guide.
ac5uuw00006683
2.Pull the side wall in the direction of arrow (3) shown in the figure and remove it while removing the
guide.
1.Remove the clip and hooks while pulling the side wall in the order of arrows (1) and (2) shown in the
figure.
Caution
• If the side wall is pulled forcibly when removing the hooks and clip, the guide could be damaged.
When pulling the side wall in the direction of arrows (1) and (2), be careful not to damage the guide.
ac5uuw00006684
2.Pull the side wall in the direction of arrow (3) shown in the figure and remove it while removing the
guide.
id091700960700
1.To prevent scratches or damage, apply protective tape to the position shown in the figure.
ac5uuw00006205
2.Insert the remover tool into the positions shown in the figure, move it in the order of arrows (1), (2), (3),
(4), (5), and (6) and detach the hooks.
3.Hold the shaded areas shown in the figure, move the center speaker grille in the order of arrows (1) and
(2) and remove it while detaching the hooks.
4.Move the tabs in the order of arrows (1) and (2) shown in the figure and remove the tweeter grille.
4.Remove the rear speaker grille in the direction of the arrow shown in the figure.
id091700898400
ATX
ac5uuw00005313
4.Using a remover tool, move the shift panel in the order of arrows (1), (2), (3), and (4) shown in the
figure, and detach the clips and hooks.
5.Move the shift panel in the direction of the arrow shown in the figure and remove it while detaching the
guides.
Note
• When replacing the shift panel, press the tabs in the order of arrows (1) and (2) shown in the figure
and remove the console mat.
MTX
3.Using a remover tool, move the shift panel in the order of arrows (1), (2), (3), and (4) shown in the
figure, and detach the clips and hooks.
4.Move the shift panel in the direction of the arrow shown in the figure and remove it while detaching the
guides.
Note
• When replacing the shift panel, press the tabs in the order of arrows (1) and (2) shown in the figure
and remove the console mat.
id091700801500
1.Hold part A shown in the figure, open the rear scuff plate in the direction of arrow (1), move it in the
direction of arrow (2), and detach tab A of the rear scuff plate from the B-pillar lower trim.
ac5uuw00005379
2.Hold the shaded areas shown in the figure, move the rear scuff plate in the direction of arrow (3), and
detach tab B of the rear scuff plate from the B-pillar lower trim.
3.Hold the shaded areas shown in the figure, move the rear scuff plate in the direction of arrow (1),
detach the clip from the inner panel, and pull out the pin.
4.Hold the shaded areas shown in the figure, move the rear scuff plate in the direction of arrow (2),
detach the clip from the inner panel, and pull out the pin.
5.Hold part A shown in the figure, open the rear scuff plate in the direction of arrow (1), move it in the
direction of arrow (2), and detach tab A of the rear scuff plate from the trunk side trim.
6.Hold the shaded areas shown in the figure, move the rear scuff plate in the direction of arrow (3), and
remove it while detaching tab B of the rear scuff plate from the trunk side trim.
id091700804300
ac5uuw00006668
id091700802600
2.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the direction
of the arrow and remove the inner handle cover while detaching the tabs.
ac5uuw00007850
ac5uuw00006164
5.Hold each shaded area and pull the rear door trim in the order of arrows (1), (2), (3), and (4), and
remove it while detaching the clips, hook, and pin.
id091700898600
ac5uuw00006685
2 Bolt
4 Screw
Console lid
5
(See CONSOLE LID REMOVAL/INSTALLATION.)
6 Screw
Side panel
7
(See Side Panel Removal Note.)
8 Screw
1.Move the side panel in the order of arrows (1) and (2) shown in the figure, and remove it while
detaching the guides.
id091700898500
3.Using a remover tool, detach the clips in the order of arrows (1) and (2) shown in the figure.
ac5uuw00005319
4.Move the console-up in the direction of arrow (3) shown in the figure and detach the clips.
6.Move the console-up in the direction of the arrow shown in the figure, detach the guides from the rear
console, and remove the console-up.
ac5uuw00005322
8.Insert the remover tool into the position shown in the figure, move it in the direction of the arrows, and
detach the clips.
9.Move the console panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and detach the
clips.
12.Move the rear console in the direction of the arrows shown in the figure, detach the clips and guides
from the center lower panel, and remove the rear console.
id091700608300
ac5uuw00006711
2 Cover No.1
3 Screw
4 Cover No.2
Note
• Meter hood No.2 (With active driving display (auto flip-up type)) cannot be disassembled. When
replacing Meter hood No.2 (With active driving display (auto flip-up type)), refer to the METER HOOD
REMOVAL/INSTALLATION. (SeeMETER HOOD REMOVAL/INSTALLATION.)
1 Screw
2 Hole cover
id091700800900
3.Hold the shaded areas shown in the figure, pull meter hood No.1 in the order of arrows (1) and (2), and
remove it while detaching clips A and B.
ac5uuw00007542
Meter hood No.2 (With active driving display (auto flip-up type))
id091700801100
Driver-side
ac5uuw00005269
5.Pull the driver-side lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and
remove it while detaching the clips, hook, tab, and guide.
Note
• When replacing the driver-side lower panel, remove the cluster switch. (SeeCLUSTER SWITCH
REMOVAL/INSTALLATION.)
Passenger-side
Removal
ac5uuw00005273
6.Move the passenger-side lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure,
and remove it while detaching the hook, clips, pins, tab, and guide.
Installation
1.Install the hook, clips, pins, tab, and guide while pressing the passenger-side lower panel in the order of
arrows (1), (2), (3), and (4) shown in the figure.
2.Assemble the passenger-side lower panel to the dashboard and tighten the bolts and screws
temporarily.
4.Measure the gap between the glove compartment and the passenger-side lower panel and verify that
the measured value is within the nominal value.
• If not within the nominal value, move the passenger-side lower panel and adjust the installation
position.
id091700803600
1.Hold the shaded areas shown in the figure and partially peel back the edge of the liftgate upper trim in
the direction of arrow (1) to detach the tab, move the liftgate upper trim in the direction of arrow (2) with
the tab detached, and detach clip A and B.
ac5uuw00006659
2.Hold the shaded areas shown in the figure, move the liftgate upper trim in the direction of the arrow and
detach the clip and pin.
3.Hold the shaded areas shown in the figure and partially peel back the edge of the liftgate upper trim in
the direction of arrow (1) to detach the tab, move the liftgate upper trim in the direction of arrow (2) with
the tab detached, and detach clip A and B.
id091700803700
1.Remove the liftgate upper trim. (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
ac5uuw00006662
3.Hold the shaded areas shown in the figure and detach the clips while moving the liftgate side trim in the
direction of the arrow.
4.Hold the shaded areas shown in the figure and partially peel back the edge of the liftgate side trim in the
direction of arrows (1) to detach the tabs, move the liftgate side trim in the direction of arrow (2) with the
tabs detached and remove the liftgate side trim while detaching the hook.
id091700467500
1.While pressing the liftgate recess in the direction of arrows (1) shown in the figure, move the liftgate
recess in the direction of arrow (2), and detach the liftgate recess tabs.
ac5uuw00006699
2.Remove the liftgate recess in the direction of arrow (3) shown in the figure while detaching the hooks of
the liftgate recess.
id091700803800
(1)Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.) (2)Liftgate side
trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.) (3)Liftgate recess (See LIFTGATE
RECESS REMOVAL/INSTALLATION.) (4)Power liftgate (PLG) rear switch (With power liftgate
system) (See POWER LIFTGATE (PLG) REAR SWITCH REMOVAL/INSTALLATION.)
3.Insert a remover tool into the service hole, move it in the direction of the arrow shown in the figure and
remove cover No.1. (Without power liftgate system)
ac5uuw00006180
4.Insert your hand into the cover No.1 installation hole and remove cover No.2 in the direction of the
arrow shown in the figure while detaching the tabs with the inserted hand. (Without power liftgate system)
6.Hold each shaded area and pull the liftgate lower trim in the order of arrows (1), (2), (3), and (4), and
remove it while detaching clips A, clips B, and the pin.
Note
• When replacing the liftgate lower trim, remove the cargo compartment light. (SeeCARGO
COMPARTMENT LIGHT REMOVAL/INSTALLATION.)
id091700804000
ac5uuw00005824
4.Pull the knee bolster in the order of arrows (1), (2) while detaching the hooks.
id091700606000
5.Pull the heel cushion in the direction of the arrow shown in the figure and remove it.
id091700801600
Caution
• The location of the headliner shown in the figure is installed to the roof panel using a clip via the
surface fastener. If the surface fastener is peeled off or a clip is removed forcibly when removing the
headliner, the headliner will be damaged. Disconnect the surface fastener using a string before
removing the headliner.
ac5wzw00009664
1.Form the steel wire (approx. φ 3 mm {0.1 in}) into the shape shown in the figure and tie a string (approx.
φ 3 mm {0.1 in}) to the steel wire end.
2.To prevent the steel wire from getting caught on the headliner, wrap the position shown in the figure
with protective tape.
REMOVAL
2.Mark the position shown in the figure using tape to verify the position of the surface fastener.
5.Open the lock covers of the wiring harness clips in the direction of arrow (1) shown in the figure and
remove the roof wiring harness in the direction of arrow (2).
ac5uuw00008137
6.Remove the wiring harness clips and disconnect the tuner and amp unit (TAU) connectors. (With center
display)
ac5uuw00008140
9.Pull the roof wiring harness and rear washer hose B in the direction of the arrow shown in the figure and
pull them out.
14.Temporarily install the seaming welts shown in the figure to the headliner.
Caution
• If the clips are detached without temporarily installing the seaming welts, the headliner may fall off
and the part may be damaged. Before detaching the clips, temporarily install the seaming welts to
prevent the headliner from falling off.
15.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the
direction of the arrow, and detach the clips.
16.For vehicles without the sunroof system, hook a string with the surface fastener using the following
procedure.
(1)Insert the steel wire processed for the preparation before servicing and a string between the roof
panel and the headliner from area A shown in the figure.
(2)Move the steel wire in the direction of arrow (1) shown in the figure and pull it out of area B shown
in the figure. (3)Insert the steel wire between the roof panel and the headliner from area C shown in
the figure. (4)Move the steel wire in the direction of arrow (2) shown in the figure and pull it out of
area D shown in the figure. (5)Adjust the string position so that the string contacts the surface
fastener.
17.For vehicles with the sunroof system, hook a string to the surface fastener using the following
procedure.
(1)Insert the steel wire processed for the preparation before servicing and a string between the roof
panel and the headliner from area A shown in the figure.
(2)Move the steel wire in the order of arrows (1) and (2) shown in the figure and pull it out of area B
shown in the figure. (3)Insert the steel wire between the roof panel and the headliner from area
Bshown in the figure. (4)Move the steel wire in the direction of arrow (3) shown in the figure and pull
it out of area C shown in the figure. (5)Adjust the string position so that the string contacts the
surface fastener.
18.Pull the string in the direction of the arrow with the string end shown in the figure held and disconnect
the surface fastener.
19.Partially peel back the seaming welts and take the headliner out from the opened liftgate.
ac5wzw00009676
1.Pull out area A of the clip for the surface fastener (roof panel side) shown in the figure using a flathead
screwdriver.
ac5uuw00008148
Note
• To avoid adhering the surface fastener to the headliner before installing the headliner, pull out area
A of the clip.
3.Press the headliner in the direction of the arrows shown in the figure and detach the clips.
9.Insert the roof wiring harness and rear washer hose B in the direction of the arrow shown in the figure.
ac5uuw00008139
11.Install the wiring harness clips and connect the tuner and amp unit (TAU) connectors. (With center
display)
13.Install the roof wiring harness in the direction of arrow (1) shown in the figure and close the lock covers
of the wiring harness clips in the direction of arrow (2).
15.Press the marked location by hand and press fit the surface fastener.
ac5wzw00009681
id091700800700
1.Pull the stay damper in the direction of the arrow shown in the figure and detach the hook.
Caution
• If the glove compartment is closed without the stay damper attached to the hook, the stay damper
may become damaged. Verify that the stay damper is attached to the hook before closing the glove
compartment.
ac5uuw00005256
ac5uuw00005257
3.Lower the glove compartment in the direction of arrow (1) shown in the figure, pull it up in the direction
of arrow (2), and remove it while detaching the hooks.
id091700802400
1.Remove the front scuff plate. (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
ac5uuw00005293
5.Pull the front side trim in the direction of the arrow shown in the figure and remove it while detaching the
clip.
id091700801400
1.Hold area A shown in the figure, open the front scuff plate in the direction of arrow (1), and detach tab A
of the front scuff plate from the front side trim while moving it in the direction of arrow (2).
ac5uuw00007544
2.Hold the shaded areas shown in the figure and detach tab B of the front scuff plate from the front side
trim while moving the front scuff plate in the direction of arrow (3).
3.Hold area A shown in the figure, open the front scuff plate in the direction of arrow (1), and detach tab A
of the front scuff plate from the B-pillar lower trim while moving it in the direction of arrow (2).
4.Hold the shaded areas shown in the figure and detach tab B of the front scuff plate from the B-pillar
lower trim while moving the front scuff plate in the direction of arrow (3).
5.Hold the shaded areas shown in the figure and detach the clip from the inner panel while moving the
front scuff plate in the direction of arrow (1).
6.Hold the shaded areas shown in the figure and detach the clip from the inner panel while moving the
front scuff plate in the direction of arrow (2).
7.Pull out the pins and remove the front scuff plate.
id091700802500
2.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the direction
of the arrow and remove the inner handle cover while detaching the tabs.
ac5uuw00007968
ac5uuw00006875
5.Hold each shaded area and pull the front door trim in the order of arrows (1), (2), (3), and (4), and
detach the clips, hook, and pin.
6.Lift up the front door trim in the direction of the arrow shown in the figure being careful not to open the
lower end of the front door trim excessively, and remove the front door trim from the clip.
8.Disconnect the power window main switch connector (driver-side) or power window subswitch
connector and door lock switch connector (passenger-side).
10.While pressing the tabs of the clip in the directions of arrows (1) shown in the figure, pull the clip in the
direction of arrow (2) to remove the clip from the front door.
id091700804200
Driver-side
ac5uuw00007851
Passenger-side
id091700803900
ac5uuw00005296
4. Move the front console box in the direction of the arrow shown in the figure and remove it while
detaching the clips.
id091700606100
ac5uuw00006706
4.Remove the foot support in the direction of the arrow shown in the figure.
id091700803000
ac5uuw00006718
ac5uuw00006719
13.Fold the floor covering and remove it from the door opening.
14.Install in the reverse order of removal. (See Floor Covering Installation Note.)
Caution
• When installing the floor covering, the floor covering may press the A/C unit drain hose and deform
it. When installing the floor covering, align the floor covering to the body to prevent deforming the A/C
unit drain hose.
2.Before installing the side wall, verify that the A/C unit drain hose is not deformed.
• If the rear seat cushion lock lever is covered by the floor mat, the rear seat cushion lock cannot be
released. When installing the floor covering, do not cover the rear seat cushion lock lever with the floor
covering.
id091700806600
2.To prevent scratches or damage, apply protective tape to the position shown in the figure.
ac5uuw00005298
ac5uuw00005299
ac5uuw00005300
5.Move the lower decoration panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and
remove it while detaching the clips.
ac5uuw00005301
Note
3.To prevent scratches or damage, apply protective tape to the position shown in the figure.
ac5uuw00005302
4.Insert remover tool A into the position shown in the figure and secure a clearance to insert remover tool
B.
6.Move remover tools A and B in the direction of the arrows shown in the figure and detach the clip.
8.Move the remover tool in the direction of the arrow shown in the figure and detach the clip.
9.Move the upper decoration panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and
remove it while detaching clips A and B.
Note
• When replacing the upper decoration panel, remove the hazard warning switch. (SeeHAZARD
WARNING SWITCH REMOVAL/INSTALLATION.)
• When replacing the upper decoration panel, remove the center ventilator grilles. (SeeVENTILATOR
GRILLE REMOVAL/INSTALLATION.)
1.To prevent scratches or damage, apply protective tape to the position shown in the figure.
3.Move the remover tool in the direction of the arrow shown in the figure and detach the clip.
4.Move the driver-side decoration panel in the direction of the arrow shown in the figure and remove it
while detaching the clip.
id091700600900
Note
• The driver-side decoration panel and lower decoration panel cannot be disassembled. When
replacing the driver-side decoration panel and lower decoration panel, refer to DECORATION PANEL
REMOVAL/INSTALLATION. (SeeDECORATION PANEL REMOVAL/INSTALLATION.)
Type A
2.Remove the hazard warning switch. (See HAZARD WARNING SWITCH REMOVAL/INSTALLATION.)
2 Bezel
3 Dashboard pad
4 Screw
5 Center panel
6 Screw
7 Print plate A
8 Screw
9 Print plate B
10 Screw
11 Decoration plate
Type B
2.Remove the hazard warning switch. (See HAZARD WARNING SWITCH REMOVAL/INSTALLATION.)
1 Screw
2 Bezel
3 Dashboard pad
4 Screw
5 Center panel
6 Screw
7 Decoration plate
id091700807200
1.With the end of the hook pressed in the direction of arrow (1) shown in the figure, pull the dashboard
under cover in the direction of arrows (2) and detach the hooks and pins.
ac5uuw00005312
2.Pull the dashboard under cover in the direction of arrow (3) shown in the figure and remove it while
releasing the guide.
Caution
id091700800300
Replacement part
Bolt
Quantity: 2
Removal
Warning
• Handling the driver's air bag module improperly can accidentally operate (deploy) the air bag
module, which may seriously injure you. Read the SRS air bag system service warnings and cautions
before handling the air bag module. (SeeAIR BAG SYSTEM SERVICE WARNINGS [STANDARD
DEPLOYMENT CONTROL SYSTEM - MEXICO SPEC.].) (SeeAIR BAG SYSTEM SERVICE
WARNINGS [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.].) (SeeAIR
BAG SYSTEM SERVICE CAUTIONS [STANDARD DEPLOYMENT CONTROL SYSTEM - MEXICO
SPEC.].) (SeeAIR BAG SYSTEM SERVICE CAUTIONS [TWO-STEP DEPLOYMENT CONTROL
SYSTEM - US/CANADA SPEC.].)
1.Disconnect the negative battery terminal and wait for 1 min or more. (See NEGATIVE BATTERY
TERMINAL DISCONNECTION/CONNECTION.)
(1)Windshield wiper arm and blade (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION.) (2)Cowl grille (See COWL GRILLE REMOVAL/INSTALLATION.)
(3)Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.) (4)Front side trim
(See FRONT SIDE TRIM REMOVAL/INSTALLATION.) (5)A-pillar trim (See A-PILLAR TRIM
REMOVAL/INSTALLATION.) (6)Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE
REMOVAL [STANDARD DEPLOYMENT CONTROL SYSTEM - MEXICO SPEC.].) (See DRIVER-
SIDE AIR BAG MODULE REMOVAL [TWO-STEP DEPLOYMENT CONTROL SYSTEM -
US/CANADA SPEC.].) (7)Steering wheel (See STEERING WHEEL AND COLUMN
REMOVAL/INSTALLATION.) (8)Upper column cover (See COLUMN COVER
REMOVAL/INSTALLATION.) (9)Lower column cover (See COLUMN COVER
REMOVAL/INSTALLATION.) (10)Lower decoration panel (See DECORATION PANEL
REMOVAL/INSTALLATION.) (11)Upper decoration panel (See DECORATION PANEL
REMOVAL/INSTALLATION.) (12)Driver-side decoration panel (See DECORATION PANEL
REMOVAL/INSTALLATION.) (13)Meter hood No.1 (See METER HOOD
REMOVAL/INSTALLATION.) (14)Center display component (With center display) (See CENTER
DISPLAY REMOVAL/INSTALLATION.) (15)Instrument cluster (See INSTRUMENT CLUSTER
REMOVAL/INSTALLATION.) (16)Meter hood No.2 (With active driving display) (See METER
ac5uuw00006726
6.Remove the electric parking brake control module. (See ELECTRIC PARKING BRAKE CONTROL
MODULE REMOVAL/INSTALLATION.)
8.Disconnect the dashboard wiring harness connectors and remove wiring harness clips A and B. (With
center display)
13.To prevent damage to the windshield, apply protective tape to the position shown in the figure.
ac5uuw00006731
16.Lift the dashboard up in the direction of arrow (1) shown in the figure and remove it from the guide pins
on the vehicle body sides, and pull out the dashboard in the direction of arrow (2).
ac5uuw00006733
18.Remove the dashboard from either the driver-side or passenger-side front door opening.
Installation
1.Rotate the plate nuts by hand in the direction of the arrow shown in the figure until they are seated.
Caution
• After removing the dashboard, the plate nuts of the member junctions will have loosened. If the
dashboard is installed with the plate nuts loosened, the plate nuts may contact the vehicle body,
causing a dent or damage to the coating film, and the dashboard installation will be difficult. Before
inserting the dashboard into the cabin, seat the plate nuts of the member junctions.
• If the plate nuts are tightened excessively, the plate nuts may not move when installing the bolts,
resulting in damage to the member junction tab and the vehicle body. After seating the plate nuts,
verify that they can be rotated by hand.
Note
• If the plate nuts cannot be rotated by hand, loosen the plate nuts using a hexagonal wrench.
2.Verify that the member junction tabs are engaged to the dashboard.
Caution
• If the member junction tabs are disengaged from the dashboard when inserting the dashboard into
the cabin, the vehicle body could be damaged. Before inserting the dashboard into the cabin, verify
that the member junction tabs are engaged with the dashboard.
3.Insert the dashboard from either the driver-side or passenger-side front door opening.
4.Move the dashboard in the direction of the arrow shown in the figure, align it with the guide pins on the
vehicle body sides, and set it.
Note
• Visually verify the installation condition of the guide pins on the vehicle body sides and the
dashboard from the position shown in the figure.
Note
• Tighten the bolts to the specified torque after positioning the member junction.
ac5uuw00006737
ac5uuw00006738
Note
• When seating the bolts, visually verify from the lower side of the dashboard that the plate nuts of the
member junctions emerge toward the body panel while rotating.
8.Verify that the bolt holes on the vehicle side and the bolt insertion position of the member junctions are
aligned.
Note
• If the bolt holes on the vehicle side and the bolt insertion position of the member junctions are not
aligned, remove the bolts on the driver-side and passenger-side and repeat from Step 5.
Caution
• If the bolts are reused, the plate nuts of the member junctions cannot be moved and the dashboard
frame and the vehicle body could be damaged. Always replace the bolts with new ones.
ac5uuw00006741
10.Tighten the bolts on the driver-side to the specified torque and install the caps.
11.Tighten the bolts on the passenger-side to the specified torque and install the caps.
ac5uuw00008369
ac5uuw00007930
17.Connect the dashboard wiring harness connectors and install wiring harness clips A and B. (With
center display)
20.Install the electric parking brake control module. (See ELECTRIC PARKING BRAKE CONTROL
MODULE REMOVAL/INSTALLATION.)
ac5uuw00006745
id091700800400
Warning
• Handling the front passenger's air bag module improperly can accidentally operate (deploy) the air
bag module, which may seriously injure you. Read the SRS air bag system service warnings and
cautions before handling the air bag module. (SeeAIR BAG SYSTEM SERVICE WARNINGS
[STANDARD DEPLOYMENT CONTROL SYSTEM - MEXICO SPEC.].) (SeeAIR BAG SYSTEM
SERVICE WARNINGS [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.].)
(SeeAIR BAG SYSTEM SERVICE CAUTIONS [STANDARD DEPLOYMENT CONTROL SYSTEM -
MEXICO SPEC.].) (SeeAIR BAG SYSTEM SERVICE CAUTIONS [TWO-STEP DEPLOYMENT
CONTROL SYSTEM - US/CANADA SPEC.].)
1.Remove the passenger-side air bag module. (See PASSENGER-SIDE AIR BAG MODULE
REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM - MEXICO SPEC.].) (See
PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT
CONTROL SYSTEM - US/CANADA SPEC.].)
2 Screw
3 Center defroster
4 Screw
5 Side defroster
6 Bolt
7 Screw
8 Dashboard frame
9 Member junction
10 Seal tape
12 Screw
13 Dashboard box
14 Screw
15 Center duct
16 Dashboard
Note
1.The shape of the wiring harness clips at the positions shown in the figure cannot be visually verified.
Refer to wiring harness clips A and B shown in the figure when removing the dashboard wiring harness.
ac5uuw00006716
id091700969100
2.Remove the console side panel. (See CONSOLE SIDE PANEL REMOVAL/INSTALLATION.)
ac5uuw00005327
6.Move the remover tools in the direction of the arrows shown in the figure and detach the clips from the
rear console.
7.Move the cup holder in the order of arrows (1) and (2) shown in the figure, and remove it while
detaching the clips and hooks.
id091700606600
ac5wzw00011715
2.Pull the clean cloth up in the direction of the arrow shown in the figure and remove the clips.
3.Hold the shaded area shown in the figure, move the console side panel in the direction of the arrow,
and remove it while detaching the clips and guides.
id091700607400
ac5uuw00006708
ac5uuw00006709
7.Move the console lid in the direction of arrow (1) shown in the figure, and detach the pins.
8.Remove the console lid in the direction of arrow (2) shown in the figure.
id091700800800
2.Press the shaded areas shown in the figure, lift the upper column cover in the direction of the arrows,
and detach the pins, tabs, and guides from the lower column cover.
ac5uuw00005259
ac5uuw00005260
4.Detach all the tabs of meter hood No.1 from the upper column cover.
3.Lower the lower column cover in the direction of arrows (2) shown in the figure while keeping it open in
the direction of arrows (1).
ac5uuw00005262
5.Move the lower column cover in the direction of the arrow shown in the figure and remove it while
pulling out the guide.
ac5uuw00005264
id091700601500
2.Remove the driver-side front scuff plate. (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
3.Remove the driver-side front side trim. (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)
ac5uuw00006700
6.Pull the driver-side lower panel in the order of arrows (1) and (2) shown in the figure, and detach the
clips, hook, and tab.
7.Set the driver-side lower panel aside to a position where the cluster switch hooks can be detached.
9.With the hooks pressed in the direction of arrows (1) shown in the figure, push out the cluster switch in
the direction of arrow (2) and remove it from the driver-side lower panel.
id091700606400
3.Move the center lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and remove
it while detaching clips A and B from the dashboard.
id091700802200
4.Pull the C-pillar trim in the order of arrows (1), (2), and (3) shown in the figure and detach the clips and
pin.
ac5uuw00006656
ac5uuw00006657
Note
• When replacing the C-pillar trim, remove the rear speaker. (With Bose®) (SeeREAR SPEAKER
REMOVAL/INSTALLATION.)
• When replacing the C-pillar trim, remove the rear speaker grille. (With Bose®) (SeeSPEAKER
GRILLE REMOVAL/INSTALLATION.)
6.Install in the reverse order of removal. (See C-Pillar Trim Installation Note.)
1.Move the C-pillar trim in the direction of the arrow shown in the figure and insert clip A into the clip B
receptacle.
2.Verify that the clip and pin installation positions and their installation holes are aligned.
id091700802000
1.Remove the front scuff plate. (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
2.Remove the rear scuff plate. (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
ac5uuw00006651
4.Hold the shaded areas shown in the figure, and while pulling the B-pillar lower trim in the directions of
arrows (1) and (2), remove the hooks and pins.
5.Hold the shaded areas shown in the figure, remove the B-pillar lower trim by pulling it in the direction of
the arrow to detach the clips and pins.
id091700802100
(1)Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.) (2)Rear scuff plate
(See REAR SCUFF PLATE REMOVAL/INSTALLATION.) (3)B-pillar lower trim (See B-PILLAR
LOWER TRIM REMOVAL/INSTALLATION.) (4)Adjust anchor cover on the front seat belt (See
FRONT SEAT BELT REMOVAL/INSTALLATION.) (5)Upper anchor installation bolt on the front seat
belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
ac5uuw00006654
3.Hold the shaded areas shown in the figure and while pulling the B-pillar upper trim in the direction of
arrow (1), remove the clips, pin A, and pin B.
Caution
• If the B-pillar upper trim is pulled forcibly when removing the clips, pin A, and pin B, the guide could
be damaged. When pulling the B-pillar upper trim in the direction of arrow (1), be careful not to
damage the guide.
4.Pull the B-pillar upper trim in the direction of arrow (2) shown in the figure, and remove it while pulling
out the guide.
id091700801800
Removal
1.Insert a tape-wrapped flathead screwdriver into the service hole and remove the assist handle covers.
ac5uuw00007548
2.Pull the assist handle in the order of arrows (1) and (2) shown in the figure and remove it while
detaching the clips.
Note
Installation
1.Push the assist handle in the direction of the arrows shown in the figure and insert it into the assist
handle brackets.
2.Push the assist handle covers in the direction of the arrows shown in the figure to install the assist
handle.
id091700801900
Replacement part
Quantity: 1
Removal
1.Disconnect the negative battery terminal. (With tweeter) (See NEGATIVE BATTERY TERMINAL
DISCONNECTION/CONNECTION.)
ac5uuw00007552
3.Hold the shaded areas of the A-pillar trim shown in the figure, pull it in the direction of the arrow, and
then detach clips A and B.
4.Cut the lead wire connecting clip B and the grommet using a nipper.
5.Pull the A-pillar trim in the direction of the arrow shown in the figure and remove it while detaching
guides A and B.
7.Remove the tweeter and the tweeter grille as a single unit. (With tweeter)
8.Insert a tape-wrapped flathead screwdriver into the position shown in the figure, move it in the direction
of the arrow, and then detach the hook.
9.Insert the tape-wrapped flathead screwdriver into the position shown in the figure, and while moving it in
the direction of arrow (1) to detach the hook, pull the grommet in the direction of arrow (2) and remove it
from the front pillar inner panel.
Installation
3.Insert guide B into the position on the dashboard shown in the figure.
4.Pull out the tweeter connector from the tweeter installation hole. (With tweeter)
7.Move the tweeter in the order of arrows (1) and (2) shown in the figure and install it. (With tweeter)
ac5uuw00007552