Professional Documents
Culture Documents
HANDLE
FRONT BACK
Multiprime
• Helps improve consistency of surface APPLICATION spills immediately. Avoid contact with skin and eyes. Wear protective
Application
COVER WITH Product is ready to use. If left undisturbed for long equipment. Trowel up/scrape up and place spilled material in clean, Bostik Australia Pty Ltd
Tile adhesive, floor leveller, screed, render and other cement based periods of time colour separation may occur but dry, sealed container. Flush spill area with water. Refer to State/ 51-71 High Street,
systems and waterproofing membranes. this does not affect performance. If desired, remix Territory Land Waste Management Authority for disposal. FIRST AID: Thomastown VIC 3074
SUBSTRATES by stirring. Do not shake as this causes foaming If poisoning occurs, contact a Doctor or Poisons Information Centre www.bostik.com.au
Ensure the surface to be primed is correctly installed, suitable for the which can lead to pin-holes. This is particularly (Phone Australia: 131126). SWALLOWED: If swallowed, do NOT
intended use and adequately prepared. Use on porous surfaces such as: important for waterproofing and levelling installations. For best induce vomiting. Immediately give a glass of water. Seek medical Bostik New Zealand Pty Ltd
results apply with a brush or broom. Take care not to froth the advice. EYE: If in eyes, hold eyes open, flood with water for at least 19 Eastern Hutt Road,
• Concrete • Fibre cement • Hebel™
• Timber primer with the brush. Apply enough Multiprime to soak into the 15 minutes and see a doctor. SKIN: If skin or hair contact occurs, flush Lower Hutt 5019
• Render • Plasterboard www.bostik.co.nz
pores. Very porous surfaces may require damping down with water
Porous Substrate Primer
skin and hair with running water (and soap if available). Seek medical
RECOMMENDATIONS prior to priming and more than one coat of Multiprime may be attention in event of irritation. INHALED: Remove from contaminated
• Refer to Technical Datasheet and SDS before use. needed. Multiprime may also be applied using a roller or sponge area. Seek medical advice if in doubt.
• Intended for use only on porous surfaces. When priming non-porous but care must be taken to ensure enough is applied and that it is
surfaces consider using Prime Grip Non-porous Primer. worked into the pores. It is likely that the porosity will vary across
• It is advised that the surface porosity is tested before work commences the job. Ensure that enough primer is used on more porous sections. SMART HELP:
(see surface preparation section). Primed surface should be touch dry before application of adhesive DO NOT REUSE CONTAINER UNLESS THOROUGHLY 1800 267 845 (AUS)
• Do not use on non-porous surfaces such as existing tiles, waterproofing or waterproofing membrane. This will normally take approximately DECONTAMINATED. SEE THE SAFETY DATA SHEET 0508 222 272 (NZ)
membranes or steel trowel finished concrete. 30 minutes in normal conditions (22°C and 50% relative humidity). FOR ADDITIONAL INFORMATION. EMERGENCY
• May be used on water based acrylic paint prior to fixing tiles with a suitable If the surface dries within 10 minutes the surface may have high
INFORMATION (ALL HOURS) AUSTRALIA: 1800 033 111
tile adhesive. Refer to the relevant adhesive Technical Datasheet for more porosity, not enough primer may have been applied or the ambient
• Improves Surface Bonding Capabilities information. conditions may be too hot. In this case it’s recommended that the
PREP
• In order for this type of primer to work effectively, enough must be applied installation technique be assessed and changed as required. In
to penetrate the surface pores. It must be worked into the substrate pores. very hot and/or low humidity conditions it is recommended that
the application be postponed until conditions are more favourable. DISCLAIMER
• Increases Working Time of Adhesives • Extra care is required when priming very porous surfaces. It is recommended
that in these cases the surface is dampened down with a wet sponge All work must be carried out in accordance with relevant
The information provided is intended for the assistance of
immediately prior to priming. More than one coat of primer may be needed. purchasers and is of a general nature. It reflects the extent of our
standards and good workmanship practices
knowledge and experience of our products and is based on tests
INDOOR & • Avoid applying onto hot surfaces or in very warm or dry conditions. This can
COVERAGE which we believe to be reliable. However, no guarantee of accuracy
OUTDOOR lead to the primer “flash” drying before it can be absorbed into the substrate Coverage can be given due to the wide range of surfaces, environmental
pores resulting in a surface film and reducing the overall bond strength. Approximately 8m2 per litre depending on porosity
of substrate. Exact coverage will vary significantly and field conditions and variations encountered in raw materials,
• Take care to use enough material when applying with a roller or sponge. These
tools can thin out the primer and not work it into the pores. It is recommended depending on surface porosity and installation manufacturing equipment and methods at the place where the
that a long nap roller is used and that the primer is flood coated whenever conditions. work is performed. Some of these will be beyond our knowledge
or control. We recommend purchasers carry out their own tests to
Barcode
to be stripped
possible. If the primer seems to be drying within minutes it is probable that not
enough is being used. determine the suitability of the product for their particular purposes.
CLEAN UP
in here
• This product will not consolidate a substrate that is dusting, spalling or Clean Up Bostik Australia Pty Ltd limits its liability to replacement of the
Use water to wash-up. Remove from surfaces using products or refund of the purchase price, but this limitation does
otherwise unsound. Additional preparation may be required prior to treatment.
a damp cloth while still wet or soft. A small amount not affect consumers’ rights which cannot be excluded by law.
• The porosity of the surface may vary across the job. Ensure that sufficient of methylated spirits in wash-up water (1-2 cups into
primer is applied to each section.
20L
AYV-20LT-C FLAT
852.1 x 312.3 mm