Professional Documents
Culture Documents
General Requirements
(Applicable Technical Standards, Tests etc.)
CIVIL WORKS
GENERAL REQUIREMENTS
(Applicable Technical Standards, Tests etc.)
CONTENTS
GENERAL REQUIREMENTS
(Applicable Technical Standards, Tests, etc.)
1 CIVIL WORKS
1.1 General
This part of the specification shall cover
¾ Design
¾ Construction
¾ Testing and
¾ Commissioning
¾ S-TR-CIVIL-MAS - Masonry
¾ S-TR-CIVIL-CONCRETE - Concrete and Reinforced Concrete
¾ S-TR-CIVIL-STEEL - Structural Steel Work
¾ S-TR-CIVIL-METAL - Metal Work
¾ S-TR-CIVIL-DRAIN - Drainage Work
¾ S-TR-CIVIL-SAN - Plumbing and Sanitary Installation
¾ S-TR-CIVIL-SURF - Surface Protection
¾ S-TR-CIVIL-ROAD - Roads and Pavements
¾ S-TR-CIVIL-FENCE - Security Fencing
¾ S-TR-CIVIL-FINISH - Finishing Schedule
¾ S-TR-CIVIL-LIGHT - Lighting and other Electrical Installations in Substations
¾ S-TR-CIVIL-CAB - Civil Works for Underground Cables
¾ S-TR-CIVIL-OHL - Civil Works for Overhead Transmission/ Distribution
Lines
• EARTHING / GROUNDING SYSTEMS
¾ S-TR-EARTH- - General Requirements (Applicable Technical Standards,
LIGHTNING-GEN Tests etc.)
¾ S-TR-EARTH-GROUND - Earthing / Grounding Systems
¾ S-TR-LIGHTNING - Lightning Protection System
• FIRE FIGHTING SYSTEMS
¾ S-TR-FIF - Fire Protection System
• ELECTROMECHANICAL SERVICES
¾ S-TR-ELMS-GEN - General Requirements (Applicable Technical Standards,
Tests etc.)
¾ S-TR-ELMS-LIFT - Lifts (Elevators)
¾ S-TR-ELMS-CRANE - Gantry Crane
¾ S-TR-ELMS- - Air Conditioning and Ventilation Systems
HVAC+VENT
Above specifications shall cover all civil works required to form a completely safe and reliably
designed system as tendered and in accordance with the technical description of the project.
For supply items standard designs and models from a manufacturing program of one supplier are
preferred, provided they meet the requirements of this Specification, and serve the intended
purpose.
If substantial improvements of any of the specified technical requirements, which are seen by the
Bidder/Contractor to provide technical or economical advantages to TRANSCO, are desired to
be presented in the Bid, the improvement may be proposed as an alternative in addition to the
specified design. However, it is not mandatory that the alternative design is to be accepted, but
shall be subject to the decision of TRANSCO upon evaluation of the same. The difference in
price shall be clearly stated in amount/percentage/unit.
It is not the intent to specify completely herein all the details of design and manufacturing of the
substation lighting system. It may be noted that norms specified are the bare minimum that is
required. The substation lighting system shall conform in all respects to high standards of
engineering design and workmanship and should be capable of performing continuous
commercial operation within the parameters guaranteed by the Bidder/Contractor in a manner
acceptable to TRANSCO, who will interpret the meanings of drawings and specifications and
shall have power to reject any material, which in his judgement is not in accordance with the
specifications and the guaranteed parameters.
All material and equipment to be used and/or supplied under these Specifications shall be new
and of the latest proven “state-of-the art” technology. Prototype equipment shall not be accepted.
3 APPLICABLE TESTS
Details of Tests are specified in Standard Technical Specification, Part:
APPROVAL OF DATA AND DRAWINGS
The following information and data must be submitted to TRANSCO for approval prior to
manufacturing of the equipment:
• Vendor(s) details / reference list
• Completely filled in data sheets
• Testing schedule
• Documentation formats and quantities.
documents must be submitted to TRANSCO:
• Bill of equipment showing complete re-ordering information for all replaceable parts
• Installation, operation and maintenance instructions including hardware / software.