Professional Documents
Culture Documents
NET
Civil Engineer Lok sewa Model Question Sets - 2
A) Modulus of elasticity
C) Modulus of rigidity
2. A piece of round steel forged in place to connect two or more steel members is known as a
A) Bolt
B) Rivet
C) Screw
D) Stud
3. The distance measured along one rivet from the centre of a rivet on it to the centre of the
adjoining rivet on the adjacent parallel rivet line, is known as
A) Staggered putch
B) Alternate pitch
C) Reeled pitch
A) Lap joints
5. In an over-reinforced section
A) When the members are subjected to altermate external loads and the bending moment in the
sections reverse
B) When the members are subjected to loading eccentric on either side of the axis
A) 12%
B) 22%
C) 32%
D) 42%
D) none of these
B) Breadth of rib plus one- half of the clear distance between the rib
A) 5 mm
B) 10 mm
C) 15 mm
D) 20 mm
14. A reinforced slab, built monolithically with the suppprting columns and is reinforced in two or
more directions, without any provisions of beams, called a
B) Flat slab
C) continuous slab
D) Circular slab
15. The diameter of the columns head should be taken as its diameter measured below the
underside of the slab at a distance of
A) 20 mm
B) 40 mm
C) 60 mm
D) 80 mm
A) Equal to width
A) Combined footings
B) Strap footing
C) None of these
18. In the case of deformed bars, the value of bond stress for various grades of concrete is
greater by..........than the plain bars:
A) 10%
B) 20%
C) 30%
D) 40%
A) Drafter
B) Dust cloth
C) scale
A) Duster
B) Chalk
C) Sand box
D) Eraser
22. Number of equal pieces of A4 size paper from A0 is equal to
A) 2
B) 4
C) 6
D) 16
A) Diagonal scale
B) T-square
C) Set square
D) Plan meter
A) Height of letter
B) Orthographic Projection
C) Trigonometric
D) Axonometric Projection
27. In a topographic drawing the symbols representing natural features are drawn by free hand
while artificial work are drawn by
A) Free hand
B) Mechanically
D) None of these
28. The technique for free hand sketch to drawing straight line is
29. The number of years required for the net operating benefits to payback the initial cost of the
project is called
A) Operating periods
B) Service periods
C) Payback periods
D) Maintenance periods
32. Find the annuity for getting 10000 at the beginning of year at a interest rate of 12% for 12
years
A) Rs. 1600
B) Rs. 1614
C) Rs. 1628
D) Rs. 1656
A) increase
B) decrease
C) constant
A) Sensitivity analysis
B) Cost analysis
C) Benefit analysis
D) None of the Above
35. The discount rate that makes the net present value equal to zero is known as:
A) Break-even point
36. The internal rate of return (IRR) is a rate of return used in capital budgeting to measures
and compare the.........of investments
A) Vulnerability
B) Subtract
C) Multiply
D) None of These
37. In Nepal, Which of the following act contains the provisions on health and safety of the
worker ?
A) Contract act
B) industry act
C) Labor act
A) 42hr
B) 45hr
C) 48hr
D) 53hr
39. Ethics is the science which deals with
A) Rightness of professional
B) Wrong of professional
D) None of these
A) 55 and 57
B) 54 and 55
C) 55 and 56
D) 57 and 58
A) 2
B) 3
C) 4
D) 5
42. The Quantity of cement concrete PCC having thickness less than 75mm is normally
measured in
A) m
B) m2
C) m3
D) lump-sump
A) Detailed estimate
C) Cube rate
D) Depreciation method
A) Separate item
A) After agreement
B) After construction
C) After maintenance
47. The estimated quality of cement recuired in cement mortar (1:6) per cubic meter will be
A) 5.4 bags
B) 4.8 bags
C) 8 bags
D) 3 bags
A) Nature of works
B) Quantity of Materials
C) Types of Workmanship
D) Dimensions
49. In Specification of earth work in foundation trenches, drains etc, lead specified is (IS Code)
A) 30 m
B) 1.5 m
C) 50 m
D) 100 m
50.
Answer Sheet
1. C 2. B 3. D 4. A 5. A 6. B 7. C 8. D 9. B 10. C
11. D 12. A 13. C 14. B 15. B 16. D 17. A 18. B 19. D 20. D
21. D 22. D 23. D 24. B 25. C 26. C 27. B 28. A 29. C 30. B
31. A 32. B 33. B 34. B 35. C 36. D 37. C 38. C 39. C 40. A
41. B 42. B 43. A 44. B 45. D 46. C 47. A 48. D 49. A 50. C