Professional Documents
Culture Documents
Ordering information
MP 5 S 4 N
Main output(Comparative value output) Sub output(Display value output)
S Type
N Indicator -
N Indicator -
1 NPN open collector quintuple output -
Y Type 2 PNP open collector quintuple output -
3 Indicator BCD Dynamic
4 Indicator PV transmission output(DC4-20mA)
5 Indicator RS485 communication output
N Indicator -
Output A Five relay(HH, H, GO, L, LL) -
1 Triple relay(H, GO, L) -
2 NPN open collector quintuple output BCD dynamic
3 PNP open collector quintuple output BCD dynamic
W Type
4 NPN open collector quintuple output PV transmission output(DC4-20mA)
5 PNP open collector quintuple output PV transmission output(DC4-20mA)
6 NPN open collector quintuple output Low speed serial output
7 PNP open collector quintuple output Low speed serial output
8 NPN open collector quintuple output RS485 communication output
9 PNP open collector quintuple output RS485 communication output
N Indicator -
Relay single(High-limit) output
M Type 1 -
+ NPN open collector output
Relay dual(High/Low-limit) output
2 -
+ NPN open collector output
Power supply 2 24VDC(Only for MP5Y-24)
4 100-240VAC 50/60Hz
S DIN W48×H48mm
Size Y DIN W72×H36mm
W DIN W96×H48mm
M DIN W72×H72mm
Digit
5 99999(5digit)
Series
MP Pulse meter
※PNP open collector output : Option
M-6
Pulse(Rate) Meter
100-240VAC 100-240VAC
Power supply 100-240VAC 50/60Hz 24VDC (C)
50/60Hz 50/60Hz Door/Area
sensor
Allowable operation voltage 90 to 110%
Power consumption Max. 7.5VA Max. 6W Max. 7VA Max. 6VA (D)
Proximity
Power for external sensor 12VDC ±10%, 80mA sensor
• Soild-state input : Max. 50kHz(Pulse width : Each over 10㎲)
Input frequency
• Contact input : Max. 45Hz(Pulse width : Over 11ms) (E)
Pressure
[Voltage input] High : 4.5-24VDC, Low : 0-1.0VDC, Input impedance : 4.5kΩ sensor
Input level [No-voltage input] Impedance at short-circuit : Max. 300Ω, Residual voltage : Max. 1V
Impedance at open-circuit : Min. 100kΩ (F)
• Mode F1, F2, F7, F8, F9, F10 : 0.0005Hz to 50kHz • Mode F3 : 0.02s to 3,200s Rotary
Measuring range encoder
• Mode F4, F5, F6 : 0.01s to 3,200s • Mode F11, F12, F13 : 0 to 4 ×10 Count
Measuring accuracy • Mode F1, F2, F7, F8, F9, F10 : F.S. ±0.05% rdg ±1digit (G)
(23 ±5℃) • Mode F3, F4, F5, F6 : F.S. ±0.01% rdg ±1digit Connector/
Socket
Display period 0.05 / 0.5 / 1 / 2 / 4 / 8sec.(It is same with period of output update.)
Number of revolution/Speed/Frequency(F1), Passing speed(F2), Cycle(F3), Passing time(F4), (H)
Time width(F5), Time defference(F6), Absolute ratio(F7), Error ratio(F8), Density(F9), Error(F10), Temp.
Operation mode controller
Length measurement(F11), Interval(F12), Multiplication(F13)
※Refer to the M-20 to 23 for the operation mode. (I)
SSR/
Prescale function Direct input method(0.000I×10-9 to 9.9999×109) Power
※1 controller
Hysteresis 0 to 9999
• Lock setting function
• Lock setting function (J)
• Monitoring delay function Counter
• Auto-Zero time setting
• Auto-zero time setting function
function
• Current output range selection(Current output type only)
• Time unit selection (K)
• Comparative output function(HH, H, GO, L, LL) Timer
function
Other functions • Time unit selection function
• Peak value monitoring
• Deviation memory function(F output mode applied only)
function (L)
• Peak value monitoring function Panel
• Memory protection
• Remote/Local switching function(Communication output type only) meter
function ※2
• Data bank switching function
(Mode F13 applied only) (M)
• Memory protection function(Mode F13 applied only) Tacho/
Speed/ Pulse
Triple relay 250VAC 3A resistive load meter
-
Main output
Quintuple relay 3a
(N)
NPN Open collector - Display
unit
(Quintuple)
12-24VDC 30mA Max. 12-24VDC 20mA max.
PNP Open collector
(O)
(Quintuple) Sensor
controller
NPN Open collector
BCD Dynamic - NPN Open collector
12-24VDC 30mA Max.
Sub output
M-7
MP5S/MP5Y/MP5W/MP5M Series
Specifications(MP5M Series)
MP5M-4N MP5M-41 MP5M-42
Model
Indicator High-limit setting type High/Low-limit setting type
Display method 7 Segment LED display(Zero blanking), Character size : W4 X H8mm
Max. indication 0.0001 to 99999
Power supply 100-240VAC 50/60Hz
Allowable operation voltage 90 to 110%
Power consumption Approx. 7.5VA(240VAC) Approx. 8VA(240VAC)
Power for external sensor 12VDC ±10%, 80mA
• Solid-state input : Max. 50kHz(pulse width : over 10㎲)
Input frequency
• Contact input : Max. 45Hz(pulse width:over 11ms)
[Voltage input] High : 4.5-24VDC, Low : 0-1.0VDC, Input impedance : 4.5kΩ
Input level [No-voltage input] Impedance at short-circuit : Max. 300Ω, Residual voltage : Max. 1V
Impedance at open-circuit : Min. 100kΩ
• Mode F1, F2, F7, F8 : 0.0005Hz to 50kHz • Mode F3 : 0.02s to 3,200s
Measuring range
• Mode F4, F5, F6 : 0.01s to 3,200s • Mode F9, F10, F11 : 0 to 4 ×109 Count
Measuring accuracy(23 ±5℃) • Mode F1, F2, F7, F8 : F.S. ±0.05% rdg ±1digit • Mode F3, F4, F5, F6 : F.S. ±0.01% rdg ±1digit
Display period 0.05 / 0.5 / 1 / 2 / 4 / 8sec.(It is same with period of output update.)
Number of revolution/Speed/Frequency(F1), Passing speed(F2), Cycle(F3), Passing time(F4),
Operation mode Time width(F5), Time difference(F6), Absolute ratio(F7), Density(F8), Length measurement(F9),
Interval(F10), Multiplication(F11) ※Refer to M-20 to 23 for operation mode.
Prescale function Direct input method(0.0001×10-9 to 9.9999×109)
Hysteresis - 0 to 9999
• Lock setting function
• Monitoring delay function
• Lock setting function • Auto-Zero time setting function
• Lock setting function • Monitoring delay function • Time unit selection function
• Auto-Zero time setting function • Auto-Zero time setting function • Peak value monitoring function
• Time unit selection function • Time unit selection function • Memory protection function
Other function
• Peak value monitoring function • Peak value monitoring function (Mode F11 applied only)
• Memory protection function • Memory protection function • Comparative output function(H, L)
(Mode F11 applied only) (Mode F11 applied only) • Output mode selection function
• High-limit output function(H) (S, H, L, B, I, F)
• Deviation memory function
(F output mode applied only)
Main Relay 250VAC 3A resistive load 1c 250VAC 3A resistive load 1a×2
-
output NPN Open Collector 30VDC 100mA Max. 30VDC 100mA Max. ×2
Memory protection Non-volatile memory(Input : Min. 100,000 operations)
Approval
Unit weight Approx. 275g Approx. 310g Approx. 330g
※MP5S, MP5Y, MP5W have same function.
※Environment resistance is rated at no freezing or condensation.
Connections
MP5M Series
● MP5M-4N(Indicator) ● MP5M-41(High-limit setting type) ● MP5M-42(High/Low-limit setting type)
Black Black Brown Blue Black Black Brown Blue High Black Black Brown Blue High Low
8 9 10 11 12 13 14 8 9 10 11 12 13 14 8 9 10 11 12 13 14
INA INB +12V 0V INA INB +12V 0V INA INB +12V 0V
15 17 15 17 15 17
16 18 16 18 16 18
H L
1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 2 3 4 5 6 7
CONTACT OUT: CONTACT OUT:
250VAC 3A 250VAC 3A
SOURCE RESISTIVE LOAD SOURCE RESISTIVE LOAD SOURCE
100-240VAC 100-240VAC 100-240VAC
50/60Hz 50/60Hz 50/60Hz
M-8
Pulse(Rate) Meter
Connections (A)
Photo
● MP5S-4N(Indicator) (B)
Fiber
optic
sensor
RESET
※1
/HOLD (C)
Door/Area
Black Black Brown Blue sensor
6 7 8 9 10 (D)
Proximity
INA INB +12V 0V sensor
(E)
Pressure
sensor
1 2 3 4 5 (F)
SOURCE ※1: It is used for RESET terminal when an operation mode Rotary
encoder
(I)
PCB SSR/
② ④ ⑥ ⑧ ⑩ Power
controller
Black
Black
(J)
Counter
Brown Blue ① ③ ⑤ ⑦ ⑨
1 2 3 4 5 6 7 1 2 3 4 5 6 7 ※Hirose Connector:
(K)
HIF3BD-10PA-2.54DS Timer
INA INB 0V +12V SOURCE INA INB 0V +12V SOURCE
HOLD/RESET 100-240VAC 50/60Hz HOLD/RESET 100-240VAC 50/60Hz
+ - + - (L)
※1 24VDC ※1 24VDC Panel
meter
※1: It is used for RESET terminal when an operation mode is F13. (Refer to M-20 to 23 for operation mode.)
(M)
Tacho/
Main output(Connector) Sub output(Connector) Speed/ Pulse
meter
● MP5Y- 1(NPN open collector output) ● MP5Y- 3(BCD dynamic output) (N)
MAIN OUT BCD OUT Display
unit
(NPN OPEN COLLECTOR:12-24VDC Max. 30mA) (NPN OPEN COLLECTOR:12-24VDC Max. 30mA)
A C D0 D2 D4 (O)
HH GO LL Sensor
controller
2 4 6 8 10
2 4 6 8 10
(P)
Switching
mode power
1 3 5 7 9 supply
1 3 5 7 9
(Q)
COM COM B D D1 D3
H L Stepper
motor&
Driver&Controller
● MP5Y- 4(PV transmission output)
● MP5Y- 2(PNP open collector output) DC4-20mA (R)
Graphic/
Load 600Ω Max. Logic
MAIN OUT (+) panel
(PNP OPEN COLLECTOR:12-24VDC Max. 30mA)
(S)
2 4 6 8 10 Field
HH GO LL network
device
2 4 6 8 10 1 3 5 7 9
(T)
Software
(-)
1 3 5 7 9 ● MP5Y- 5(RS485 communication output)
RS485 (U)
COM H L B(-) Other
2 4 6 8 10
1 3 5 7 9
M-9
MP5S/MP5Y/MP5W/MP5M Series
MP5W Series
● MP5W- N(Indicator) ● MP5W- A(Five relay output)
CONTACT OUT:
10 11 12 13 14 15 250VAC 3A 1a
Black Black Blue Brown HH H GO L LL COM RESISTIVE LOAD
1 2 3 4 5 6 7 8 9
MAIN OUT 2 4 6 8 10 12 14 16 18 20 2 4 6
MAIN OUT
(NPN open collector (PNP open collector
: 12-24VDC Max. 20mA) 1 3 5 7 9 11 13 15 17 19 :12-24VDC Max. 20mA) 1 3 5
● MP5W- 6/ MP5W- 7(NPN/PNP open collector output + Low speed serial output)
+24VDC ※POL signal is on when it is - display value
HH GO LL 30mA Max. ※POL CLOCK LATCH HH GO LL
2 4 6 8 10 12 14 16 18 20 MAIN OUT 2 4 6
MAIN OUT
(NPN open collector (PNP open collector
: 12-24VDC Max. 20mA) 1 3 5 7 9 11 13 15 17 19 :12-24VDC Max. 20mA) 1 3 5
COM1 H L COM1 H L
0V A(+)
RS485
M-10
Pulse(Rate) Meter
(B)
● Bracket 48 10 90
Min. 55 Fiber
optic
sensor
+0.5
0
(C)
45.5
Door/Area
sensor
Min. 62
61
45
+0.5
45.5 0
(D)
Proximity
sensor
(E)
Pressure
sensor
● MP5Y Series
● Panel cut-out (F)
Rotary
encoder
85 ※There is no Min. 91
72 6 104 connector in
(G)
indicator. Connector/
Socket
31.5 + 00.5
Min. 40
36
30
(H)
+0.7
68 0
Temp.
controller
100
(I)
※Hirose connector : HIF3BD-10PA-2.54DS SSR/
Power
controller
in indicator.)
Min. 116 (L)
Panel
48
meter
46 + 0.6
0
(M)
Tacho/
Min. 52
Speed/ Pulse
+0.8 meter
Main Terminal 92 0
(N)
Display
unit
(O)
※Hirose connector(There is no connector in indicator.): Sensor
6 103 controller
HIF3BA-20PA-2.54DS
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(U)
Other
Min. 91
67
+0.7
68 0
M-11
MP5S/MP5Y/MP5W/MP5M Series
Input specifications
Input signal
● Solid-state input
• Input frequency : 50kHz Max. Min. 10㎲
Standard duty ratio of input signal is 1:1,
High
ON/OFF pulse width should be over 10㎲.
• Input voltage level : High → 4.5-24VDC, Low → 0-1.0VDC Low
ON OFF *T : 1cycle of input signal
● Relay contact input
• Input frequency : 45Hz Max. T
ON/OFF pulse width should be over 11ms.
• Relay contact specification : Please use a relay contact that can carry the load current(Min. 12VDC 2mA).
Input type
MP5 has NPN input and PNP input and it is able to select in Parameter group 1.
● When it is NPN input type
②NPN voltage ③NPN open collector
①Contact output type sensor output type sensor MP5 Series
+12V
Sensor circuit
Sensor circuit
Main circuit
4.5kΩ
IN
0V(COM)
Sensor circuit
Main circuit
IN
4.5kΩ
0V(COM)
M-12
Pulse(Rate) Meter
Low speed serial output(Negative logic) (A)
Photo
● Output : Display value electric
sensor
● Output signal : Clock, Data, Latch
● Clock cycle : 50Hz (B)
Fiber
● Output CLK bit : 25 bit optic
sensor
● Output Data bit : 25 bit
● Output form : NPN open collector (C)
Door/Area
● Rated load voltage : 12-24VDC sensor
20ms (F)
Rotary
encoder
Data D1 D2 D3 D23 D24 D25 D1 D2 D3 D4
20㎲ (G)
Connector/
Socket
5ms
(H)
Latch Temp.
controller
Clock 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 (J)
Counter
ordering Shift
(K)
Timer
Segment
Data ordering
MSB(4)
MSB(3)
MSB(2)
MSB(1)
MSB(5)
LSB(5)
LSB(4)
LSB(3)
LSB(2)
LSB(1)
(L)
DP(3)
DP(2)
DP(1)
DP(5)
DP(4)
Panel
meter
Decimal Data Decimal Data Decimal Data Decimal Data Decimal Data (M)
Tacho/
point point point point point Speed/ Pulse
meter
104 Digit 103 Digit 102 Digit 101 Digit 100 Digit (N)
Display
unit
PV transmission output(DC4-20mA)
● Application : Transmit the measured value (O)
Sensor
● Function : This function is to transmit DC4-20mA converted Display
controller
from measured display value between High limit output(FS-H) value (P)
and Low limit (FS-L). FS-H Switching
mode power
● Range of High/Low limit output setting supply
• High limit setting range (FS-H) If set FS-L and FS-H in FS-L (Q)
From min. to max within range of measurement certain section, the output will be Stepper
motor&
• Low limit setting range (FS-L) DC4-20mA. Driver&Controller
M-13
MP5S/MP5Y/MP5W/MP5M Series
PSt;;
Parameter group 0
PSt ;
PSt L
PStLL
:PEK
lPEK
MODE
IN-A
IN-B
Parameter group 1
OVT-T
;YS
GVArD fDEFY
GVArD STArT
AUToA
AUToB
MEMO
pBANY
DOT
tVNT
PSt;;
Parameter group 2
PSt ;
PSt L
PStLL
PScaH
PScaY
PScbH
PScbY
DISpT
FS-;
Parameter group 3
FS-L
ADDR
BPS
REMOT
LOC
※ : Data bank(pBANK)setting is available in only MP5W-☐N.
M-14
Pulse(Rate) Meter
● " " : When select the operation mode, the parameter will be displayed. (B)
"×" : When select the operation mode, the parameter will not be displayed. Fiber
optic
● " " : It is only able to set NPn:For PNp:F for IN-B sensor type in F11, F12, F13 of operation mode. sensor
PSt;;
(D)
PSt ; Proximity
sensor
Parameter PSt L
(E)
group 0
PStLL Pressure
sensor
:PEK
(F)
lPEK Rotary
encoder
MODE (G)
Connector/
IN-A Socket
IN-B (H)
Temp.
OVT-T controller
FS-L (S)
Field
Parameter ADDR network
device
group 3
BPS When it is RS485 communication output, it operates in all mode.
(T)
REMOT Software
(U)
M-15