Professional Documents
Culture Documents
3rd Quarter
Summative Test Set 1
WEEK 1 and 2
TLE 7
CARPENTRY
Directions: Read and answer each item. Write the letter of your answer on the SEPARATE PAPER
PROVIDED TO YOU.
B. Read and answer each item. Write the letter of your answer on the SEPARATE PAPER
PROVIDED TO YOU.
11. What is the most frequently used material in carpentry which is used to used houses and furniture?
a. Varnish b. Paint c. wood d. plywood
12. It is a type of wood that has been processed or sawn into beams and planks, a stage in the process
of wood production.
a. plywood b. lumber c. narra d. yakal
13. It is by-product of lumber.
a. hinge b. shellac c. wood d. plywood
14. It is a coloring substance composed of pigment, vehicle, thinner and drier.
a. Varnish b. adhesive c. paint d. shellac
15. A carpentry material used with a padlock and has a slotted plate fitting over the staple to prevent
its removal when locked.
a. Drawer pull b. safety hasp c. Hinge d. padlock
16. It is a movable joint or mechanism on which a door gate or lid swings as it opens or closes.
a. drawer pull b. safety hasp c. hinge d. padlock
17. It is used to join wood, metal, stone and other materials.
a. shellac b. adhesive c. varnish d. paint
18. These are used in digging in and wedging into a material when turned using a screwdriver.
a. coping saw b. screws c. screw drivers d. chisels
19. What do you call a carpentry material which is applied on the wood in a thin film giving the wood a
transparent shine?
a. Varnish b. adhesive c. paint d. shellac
20. A carpentry material used as a handle to pull a drawer out of a chest of drawers.
a. drawer pull b. safety hasp c. Hinge d. padlock
¾ plywood
these are the materials to be written on the “MATERIALS AND
Thinner DESCRIPTION” below , make sure to write it on its
sand paper corresponding requisition unit
__________________ _____________________
(your name)
Republic of the Philippines
Caraga Administrative Region
Division of Butuan City
PINAMANCULAN NATIONAL HIGH SCHOOL
Butuan City
TLE 7
CARPENTRY
Answer Sheet
1. 1. 1.
2. 2. 2.
3. 3. 3.
4. 4. 4.
5. 5. 5.
6. 6-10.(sentence form) 6.
7. 7.
8. 8.
9. 9.
10. 10.
11. 11. 11.
12. 12. 12.
13. 13. 13.
14. 14. 14.
15. 15. 15.
16. 16-20. (STOP SIGN) 16.
17. 17.
18 18
19. 19.
20. 20.
21. 21-25. (POISONOUS SIGN) 21-25. (paragraph form)
22.
23.
24.
25.
26. 26-30. (SLIPPERY WHEN WET)
27.
28.
29.
30.
3rd Quarter
Summative Test Set 2
WEEK 3 and 4
I . Write TRUE if the statement is correct and FALSE if it’s not correct.
1. Materials and tools may be substituted if it can save and lower cost regardless of the effect on the
quality of work.
2. Request is done as per company’s standard operating procedure.
3. Bulky and heavier materials on the top, lighter and smaller materials at the bottom.
4.Purchased materials are listed in the requisition form.
5. Needed materials are listed in the requisition form.
6-10. Why is it important to inspect and check materials and tools for defects and damage before
receiving them?
I . Classify the following tools according to its uses; choose your answer from the box.
1. Try square
2. Pencil
3. Compass
a. Driving tools
4. Chisel
b. Personal Protective Equipment
5. Rip saw c. Portable power tools
6. Drill bit d. Miscellaneous Tools
7. Screw driver e. Holding tools
8. Apron f. Boring tools
9. Jigsaw g. Tooth-cutting tools
10. Paint brush h. Edge cutting tools
i. Testing tools
11. Mallet
j. Marking lining tools
12. Coping saw
13. Pencil
14. C-clamp
15. Electric drill
II . Read the questions below and write the letter of your answer on the answer sheet.
16. It reduces friction between moving metal surfaces. It prevents corrosion, block contaminants and
can serve as a coolant.
a. paint b. varnish c. lubricants d. glue
17. A type of oil that contain little wax.
a. naphthenic oil b. paraffinic oils c. silicones d. greases
18. These are ideal for lubricating bearings, gaskets, seals and other moving parts.
a. Oil b. greases c. silicones d. dry lubricant
19. This lubricant is used mainly to dissolve rust.
a. Oil b. rust remover c. silicones d. dry lubricant
20. These are known as very stable and very inert lubricants, which provide a wider range of operating
temperatures.
a. Penetrating lubricans b. Silicones c. Rust remover d. oil